Search NASA⌕ Search

SEARCH · Search NASA

Results for “AFTERBURNER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Advanced supersonic propulsion study

A study was conducted to determine the promising propulsion systems for advanced supersonic transport application, and to identify the critical propulsion technology requirements. It is shown that noise constraints have a major effect on the selection of the various engine types and cycle parameters. Several promising advanced propulsion systems were identified which show the potential of achieving lower levels of sideline jet noise than the first generation supersonic transport systems. The non-afterburning turbojet engine, utilizing a very high level of jet suppression, shows the potential to achieve FAR 36 noise level. The duct-heating turbofan with a low level of jet suppression is the most attractive engine for noise levels from FAR 36 to FAR 36 minus 5 EPNdb, and some series/parallel variable cycle engines show the potential of achieving noise levels down to FAR 36 minus 10 EPNdb with moderate additional penalty. The study also shows that an advanced supersonic commercial transport would benefit appreciably from advanced propulsion technology. The critical propulsion technology needed for a viable supersonic propulsion system, and the required specific propulsion technology programs are outlined.

Sabatella, J. A.↗
NASA NTRS1974

Some comparisons of the flow characteristics of a turbofan compressor system with and without inlet pressure distortion

The measured effects of a circumferential distortion in inlet total pressure on the fan, low, and high compressor of an afterburning turbofan engine are presented and discussed. Extensive inner-stage instrumentation, combined with a unique test technique offered an accurate means of measuring the shifts in flow, performance, and stall mechanisms within the compressor. These effects are compared at one speed to the corresponding effects measured with undistorted inlet flow. The results show the rate at which the distorted flow areas were attenuated and rotated as well as the change in flow velocities that occurred at various points in the compressor. High response pressure traces indicated the location of stalls including the sequence of dynamic events from the onset and propagation of various stall-recovery events, to compressor surge, to the resulting hammershock.

Evans, D. G.↗
NASA NTRS1974

Cold-flow performance of several variations of a ram-air-cooled plug nozzle for supersonic-cruise aircraft

Experimental data were obtained with a 21.59 cm (8.5 in.) diameter cold-flow model in a static altitude facility to determine the thrust and pumping characteristics of several variations of a ram-air-cooled plug nozzle. Tests were conducted over a range of nozzle pressure ratios simulating supersonic cruise and takeoff conditions. Primary throat area was also varied to simulate afterburner on and off. Effect of plug size, outer shroud length, primary nozzle geometry, and varying amounts of secondary flow were investigated. At a supersonic cruise pressure ratio of 27, nozzle efficiencies were 99.7 percent for the best configurations.

Harrington, D. E.↗
NASA NTRS1974

Summary of recent investigations of inlet flow distortion effects on engine stability

A review is presented of recent experimental results, analytical procedures and test techniques employed to evaluate the effects of inlet flow distortion on the stability characteristics of representative afterburning turbofan and turbojet compression systems. Circumferential distortions of pressure and temperature, separately and in combination, are considered. Resulting engine sensitivity measurements are compared with predictions based on simplified parallel compressor models and with several distortion descriptor parameters.

Graber, E. J., Jr.↗
NASA NTRS1974

Some comparisons of the flow characteristics of a turbofan compressor system with and without inlet pressure distortion

The measured effects of a circumferential distortion in inlet total pressure on the fan, low, and high compressor of an afterburning turbofan engine are presented and discussed. Extensive inner-stage instrumentation, combined with a unique test technique offered an accurate means of measuring the shifts in flow, performance, and stall mechanisms within the compressor. These effects are compared at one speed to the corresponding effects measured with undistorted inlet flow. The results show the rate at which the distorted flow areas were attenuated and rotated, as well as the change in flow velocities that occurred at various points in the compressor. High response pressure traces indicated the location of stalls including the sequence of dynamic events from the onset and propagation of various stall-recovery events, to compressor surge, to the resulting hammershock.

Evans, D. G.↗
NASA NTRS1974

Conceptual design of a lift fan plus lift/cruise fighter aircraft

Results of a design synthesis and mission analysis of a supersonic VTOL fighter aircraft are presented. Propulsive lift is provided by a single turbotip-driven lift fan and deflected thrust from a high performance turbofan cruise engine fitted with an afterburner for supersonic flight. The inlet and thrust diverter in the main engine tail-pipe are seen to be the principal design problems. V/STOL and supersonic design tradeoffs are addressed in lift fan sizing and placement, reaction and aerodynamic control sizing, fuselage volume requirements, and area ruling. Range and turn rate are used as figures of merit.-

Hill, G. C.↗
NASA NTRS1975

Digital implementation of the TF30-P-3 turbofan engine control

The standard hydromechanical control modes for TF30-P-3 engine were implemented on a digital process control computer. Programming methods are described, and a method is presented to solve stability problems associated with fast response dynamic loops contained within the exhaust nozzle control. A modification of the exhaust nozzle control to provide for either velocity or position servoactuation systems is discussed. Transient response of the digital control was evaluated by tests on a real time hybrid simulation of the TF30-P-3 engine. It is shown that the deadtime produced by the calculation time delay between sampling and final output is more significant to transient response than the effects associated with sampling rate alone. For the main fuel control, extended update and calculation times resulted in a lengthened transient response to throttle bursts from idle to intermediate with an increase in high pressure compressor stall margin. Extremely long update intervals of 250 msec could be achieved without instability. Update extension for the exhaust nozzle control resulted in a delayed response of the afterburner light-off detector and exhaust nozzle overshoot with resulting fan oversuppression. Long update times of 150 msec caused failure of the control due to a false indication by the blowout detector.

Cwynar, D. S.↗
NASA NTRS1975

Nozzle exit exhaust products from space shuttle boost vehicle (November 1973 design)

Principal exhaust species emitted at various altitudes for two trajectories of the space shuttle vehicle are presented. The exhaust composition is given for the nozzle exit plane on the basis of equilibrium chemistry. Afterburning of excess H, H2, and CO in the plume is accounted for. Species considered include HCl and Al2O3, which have been recognized as environmentally significant, as well as others such as H2O (produced by both the solid rocket motor and the orbiter main engine) which, although innocuous, may participate in subsequent chemical reactions in the atmosphere.

Source record↗
NASA NTRS1975

Propulsion systems technology

The selection of components, control design, simulation, and tests are examined for designing supersonic propulsion systems. Inlet-engine combination under electronic control are shown. Design and test results from the integrated control for afterburning turbofan and supersonic cruise inlet are presented.

Hiller, K. W.↗
NASA NTRS1975

NO sub x deposited in the stratosphere by the space shuttle, phase 1

The results of calculations to determine the amount of NOx deposited in the stratosphere by space shuttle solid rocket motors (SRM) are presented. Flow properties and chemical composition in the exhaust nozzle and plume were analyzed. The nozzle calculations show that about 4.5 lbm/sec of NOx leaves the two SRMs. The total amount of NOx deposited in the stratosphere is related to the amount leaving the nozzle via an overall plume enhancement factor (OPEF), which depends upon the influence of afterburning and shocks in enhancing the exit plane NOx mole fraction. Calculations show that the OPEF is approximately 2, indicating the mass flow of NOx in the plume to be approximately l0 lbm/sec at 30 km altitude with a possible error factor of 4. For a vehicle velocity of 3750 ft/sec, therefore, the NOx deposition rate in the stratosphere is about 2.7 x 10(-3) lbm/ft.

Pergament, H. S.↗
NASA NTRS1975

Effect of a 180 deg-extent inlet pressure distortion on the internal flow conditions of a TF30-P-3

The measured effects of inlet pressure distortion on the internal flow temperatures and pressures of a TF30-P-3 afterburning turbofan engine are reported. Extensive inner-stage instrumentation combined with stepwise rotation of pressure distortion provided a high degree of circumferential resolution in the data. The steady-state spatial variation in pressures, temperature, and calculated flow velocity and the amplitude and extent of the distorted sectors are given. Data are presented for runs of 77 and 90 percent of low-speed-rotor design speed at pressure distortion levels two-thirds of that required to stall the engine. These data are compared with data taken at clean-inlet conditions. Results indicate that the inlet pressure distortion was quickly attenuated within the compressor, except at the hub of the low-pressure compressor. The distorted sectors also swirled and varied in extent as they passed through the engine. Average velocities within the compressor were about equal to the clean-inlet values.

Debogdan, C. E.↗
NASA NTRS1974

Castable thermal insulation for use as heat shields

Structural members supporting the afterburners of high thrust rocket engines are subjected to extreme heating, along with severe vibration and high acceleration levels during early lift-off. Chemically-bonded, castable, zircon composite foams were developed and successfully tested to meet specific, laboratory simulated lift-off conditions.

Mountvala, A. J.↗
NASA NTRS1975

Design and evaluation of a sensor fail-operational control system for a digitally controlled turbofan engine

A self-learning, sensor fail-operational, control system for the TF30-P-3 afterburning turbofan engine was designed and evaluated. The sensor fail-operational control system includes a digital computer program designed to operate in conjunction with the standard TF30-P-3 bill-of-materials control. Four engine measurements and two compressor face measurements are tested. If any engine measurements are found to have failed, they are replaced by values synthesized from computer-stored information. The control system was evaluated by using a realtime, nonlinear, hybrid computer engine simulation at sea level static condition, at a typical cruise condition, and at several extreme flight conditions. Results indicate that the addition of such a system can improve the reliability of an engine digital control system.

Hrach, F. J.↗
NASA NTRS1976

Modeling and analysis of the TF30-P-3 compressor system with inlet pressure distortion

Circumferential inlet distortion testing of a TF30-P-3 afterburning turbofan engine was conducted at NASA-Lewis Research Center. Pratt and Whitney Aircraft analyzed the data using its multiple segment parallel compressor model and classical compressor theory. Distortion attenuation analysis resulted in a detailed flow field calculation with good agreement between multiple segment model predictions and the test data. Sensitivity of the engine stall line to circumferential inlet distortion was calculated on the basis of parallel compressor theory to be more severe than indicated by the data. However, the calculated stall site location was in agreement with high response instrumentation measurements.

Mazzawy, R. S.↗
NASA NTRS1976

IPCS implications for future supersonic transport aircraft

The Integrated Propulsion Control System (IPCS) demonstrates control of an entire supersonic propulsion module - inlet, engine afterburner, and nozzle - with an HDC 601 digital computer. The program encompasses the design, build, qualification, and flight testing of control modes, software, and hardware. The flight test vehicle is an F-111E airplane. The L.H. inlet and engine will be operated under control of a digital computer mounted in the weapons bay. A general description and the current status of the IPCS program are given.

Billig, L. O.↗
NASA NTRS1976

Jet exhaust and support interference effects on the transonic aerodynamic characteristics of a fighter model with two widely spaced engines

Jet exhaust, nozzle installation, and model support interference effects on the longitudinal aerodynamic characteristics of a twin-engine fighter model were determined. Realistic jet exhaust nozzle configurations and a reference configuration with a simulated vertical-tail support were tested. Free-stream Mach number was varied from 0.6 to 1.2, and model angle of attack from 0 deg to 9 deg. The jet exhaust affected drag more than it affected lift and pitching moment. The largest effects occurred at a Mach number of 0.9 and for the afterburning mode of exhaust nozzle operation. The combined differences between the aerodynamic characteristics of the realistic and reference configurations (which were due to afterbody and nozzle contours, jet operation, and simulated reference support interference) were considerably different from those for the jet interference alone.

Compton, W. B., III↗
NASA NTRS1977

Effect of nonlifting empennage surfaces on single-engine afterbody/nozzle drag at Mach numbers from 0.5 to 2.2

The effect of empennage interference on the drag characteristics of a model with a single engine fighter aft end with convergent-divergent nozzles was studied. The dry and maximum afterburning nozzle power settings were investigated. A high pressure air system was used to provide jet total pressure ratios up to 20.0. In an attempt to quantify and reduce adverse empennage interference and decrease aft-end drag, several empennage arrangements (variable tail surface location), contour bump configurations, and locally contoured afterbodies were investigated. The results of the investigation indicate that empennage interference effects can be significant at transonic and supersonic speeds. The most effective means of reducing adverse empennage interference is the proper relocation of individual tail surfaces. The aft or conventional empennage arrangement produced the highest aft-end drag at all conditions investigated.

Berrier, B. L.↗
NASA NTRS1976

Procedures used in flight tests of an integrated propulsion control system on an F-111E airplane

A digital integrated propulsion control system (IPCS) was tested on an F-111E airplane. The IPCS provided full authority control of the left inlet and the TF30 afterburning engine. Supersonic test conditions were of primary interest. The operational procedures and maneuvers developed for IPCS evaluation, displays for test monitoring and data acquisition, flight safety, and problems encountered are discussed. The software refinements that made modifications to standard flight test procedures necessary are described. The flexibility of digital control and the ways software was used to overcome hardware deficiencies are discussed. Application of these procedures to a typical IPCS flight is described.

Baer, J. L.↗