Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALUMINUM ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Strengthening model development and effects of low diffusing solutes to coarsening resistance in aluminum alloys

A modified Orowan strengthening model is proposed to account for finite rod-shaped precipitates with hemispherical caps in aluminum alloy systems. A combined computational and experimental approach is used to study the influences of anisotropic Orowan looping and solute-dislocation interaction on temperature-dependent yield strength. Here, the strengthening model is validated with a dataset containing 297 experimental precipitate geometries, chemistries, temperatures, and strength measurements, and achieves a strong predictive correlation of 0.8713 with experimentally measured yield strengths. Under conditions that are applicable to coarsening, constant particle volume fraction and aspect ratio, the model predicts that short rod precipitates provide far superior strengthening effects compared to plate precipitates. A cast Al-Si-Mg-Cu alloy with rod-shaped Q-phase (Al 3 Cu 2 Mg 9 Si 7 ) precipitates was developed with a novel chemistry exploring the use of low-diffusivity elements (Mn, Ni, V, Zr) to limit precipitate coarsening. The thermodynamic behavior of Mn, Ni, V, and Zr across the Q-phase interface is examined using transmission electron microscopy (TEM), first-principles density-functional theory (DFT) calculations. and atom-probe tomography (APT). DFT calculations utilizing TEM identified Q-phase/Al-matrix interfaces show that Mn, Ni, V, and Zr preferentially segregate to the Q-phase precipitate boundaries which suggests inhibition of precipitate coarsening and higher strengths after temperature exposure. Atom-probe tomography confirms solute atom partitioning/segregation at the Q-phase/Al-matrix interface, found in the modified commercial AS7GU alloy (A356 +0.5%Cu), which supports these observations.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Conversion Coatings for Aluminum Alloys by Chemical Vapor Deposition Mechanisms

With the rise of environmental awareness and the renewed importance of environmentally friendly processes, the United States Environmental Protection Agency has targeted surface pre-treatment processes based on chromates. Indeed, this process has been subject to regulations under the Clean Water Act as well as other environmental initiatives, and there is today a marked movement to phase the process out in the near future. Therefore, there is a clear need for new advances in coating technology that could provide practical options for replacing present industrial practices. Depending on the final application, such coatings might be required to be resistant to corrosion, act as chemically resistant coatings, or both. This research examined a chemical vapor deposition (CVD) mechanism to deposit uniform conversion coatings onto aluminum alloy substrates. Robust protocols based on solutions of aryl phosphate ester and multi-oxide conversion coating (submicron) films were successfully grown onto the aluminum alloy samples. These films were characterized by X-ray Photoelectron Spectroscopy (XPS). Preliminary results indicate the potential of this technology to replace aqueous-based chromate processes.

Reye, John T.↗
DOE OSTI2023

ON PROCESS STABILITY IN WAAM-CMT OF ALUMINUM ALLOYS

Wire-arc additive manufacturing (WAAM) has become a cost-efficient metal additive manufacturing process. However, depositing aluminum with WAAM is challenging due to its sensitivity to heat input (linear energy density), which can cause undesirable surface topology waviness if not controlled. Thus, a process window is needed that can produce stable geometry and deposition conditions while minimizing production times. In this study, 5183 aluminum alloy wire is used to deposit 10-layer walls with varying wire feed speeds (WFS) and traverse speeds (TS) (at a constant WFS/TS ratio) and varying interpass temperature (IPT). In-situ process data consisting of optical contact-tip-workpiece-distance (CTWD) and current/voltage measurements are collected to determine process condition stability throughout the build. Part geometry is measured using a 3D scanner and build porosity is characterized via digital X-ray. A process window is identified that produces stable surface topology and process conditions at a minimal production time.

aluminum alloy↗
NASA NTRS1939

Combined Beam-column Stresses of Aluminum-alloy Channel Sections

The results of a research program to obtain design data on the strength of open-channel aluminum-alloy sections subjected to combined column and beam action. The results of the tests of about 70 specimens were graphed for stresses due to axial load and stresses due to bending loading as functions of length to radius of gyration of the specimens. From these graphs a design chart was derived that is suitable for ready use.

COLUMNS, ALUMINUM-ALLOY - ALCOA 24ST - STRENGTH↗
DOE OSTI2022

Effect of Processing on Precipitation Kinetics in Nano Polycrystalline 7075 Aluminum Alloy

Fairmount Technologies (FT) seeks to optimize the thermomechanical processing of Aluminum Alloy 7075. The target yield strength is 20% higher than commercially available 7075-T6 temper sheet which will enable structural light weighting by a similar magnitude and reduce the carbon footprint of the transportation sector. To reduce processing cost and make this commercially viable, it is important to understand physical mechanisms driving microstructural changes. A mesoscale phase-field model seeded with experimentally measured microstructures and assessed thermodynamic and kinetic properties will be developed and exercised using HPC at PNNL. It will account for the effect of deformation, temperature, and chemistry on precipitation kinetics in nanocrystalline microstructures. Our objective is to understand this “stress-aging” coupling by performing parametric simulations with mesoscale models for a better understanding of GP zone and η' formation in nanocrystalline 7075 Al. This will help FT optimize processing schedules to achieve desired microstructures that increase both strength and ductility.

36 MATERIALS SCIENCE↗
NASA NTRS1981

An improved stress corrosion test medium for aluminum alloys

A laboratory test method that is only mildly corrosive to aluminum and discriminating for use in classifying the stress corrosion cracking resistance of aluminum alloys is presented along with the method used in evaluating the media selected for testing. The proposed medium is easier to prepare and less expensive than substitute ocean water.

Humphries, T. S.↗
NASA NTRS1984

The effect of thickness on fatigue crack propagation in 7475-T731 aluminum alloy sheet

Tests were conducted on three thicknesses of 7475-T731 aluminum alloy sheet to investigate the effect of thickness on fatigue crack propagation under constant amplitude loading conditions and on retardation following a single peak overload. Constant amplitude loading tests were performed at stress ratios of 0.05 and 0.75 to obtain data for conditions with crack closure and without crack closure, respectively. At both stress ratios a thickness effect was clearly evident, with thicker specimens exhibiting higher growth rates in the transition from plane strain to plane stress region. The effect of thickness for a stress ratio of 0.05 corresponded well with the fracturing mode transitions observed on the specimens. A model based on the strain energy release rate which accounted for the fracture mode transition was found to correlate the thickness effects well. The specimens tested at the stress ratio of 0.75 did not make the transition from tensile mode to shear mode, indicating that another mechanism besides crack closure or fracture mode transition was active.

Daiuto, R. A.↗
NASA NTRS2004

Effect of Thermal Exposure on the Tensile Properties of Aluminum Alloys for Elevated Temperature Service

Tensile properties were evaluated for four aluminum alloys that are candidates for airframe applications on high speed transport aircraft. These alloys included the Al-Cu-Mg-Ag alloys C415 and C416 and the Al-Cu-Li-Mg-Ag alloys RX818 and ML377. The Al-Cu-Mg alloys CM001, which was used on the Concorde SST, and 1143, which was modified from the alloy used on the TU144 Russian supersonic aircraft, were tested for comparison. The alloys were subjected to thermal exposure at 200 F, 225 F and 275 F for times up to 30,000 hours. Tensile tests were performed on thermally-exposed and as-received material at -65 F, room temperature, 200 F, 225 F and 275 F. All four candidate alloys showed significant tensile property improvements over CM001 and 1143. Room temperature yield strengths of the candidate alloys were at least 20% greater than for CM001 and 1143, for both the as-received and thermally-exposed conditions. The strength levels of alloy RX818 were the highest of all materials investigated, and were 5-10% higher than for ML377, C415 and C416 for the as-received condition and after 5,000 hours thermal exposure. RX818 was removed from this study after 5,000 hours exposure due to poor fracture toughness performance observed in a parallel study. After 30,000 hours exposure at 200 F and 225 F, the alloys C415, C416 and ML377 showed minor decreases in yield strength, tensile strength and elongation when compared to the as-received properties. Reductions in tensile strength from the as-received values were up to 25% for alloys C415, C416 and ML377 after 15,000 hours exposure at 275 F.

Edahl, Robert A., Jr.↗
NASA NTRS1945

Column and Plate Compressive Strengths of Aircraft Structural Materials: Extruded 24S-T Aluminum Alloy

Column and plate compressive strengths of extruded 24S-T aluminum alloy were determined both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-,and channel-section columns. These tests are part of an extensive research investigation to provide data on the' structural strength of various aircraft materials. The results are presented in the form of curves and charts that are suitable for use in the design and analysis of aircraft structures.

Heimerl, George J.↗
DOE OSTI2021

High speed manufacturing of aluminum alloy 7075 tubing by Shear Assisted Processing and Extrusion (ShAPE)

Shear assisted processing and extrusion (ShAPE) was used to extrude aluminum alloy 7075 tubing at speeds up to 12.2 m/min. This is in comparison to 2.0 m/min which is generally the limit for conventionally extruded 7075. The increased speed is primarily attributed to more extensive shear deformation, compared to conventional extrusion, which results in a high density of low angle grain boundaries that facilitate continued deformation and delay the onset of surface tearing. Mechanical testing after heat treating to the T6 condition gave an ultimate tensile strength of 565.3 ± 4.6 MPa, yield strength of 495.7 ± 8.7 MPa, and elongation of 16.8 ± 0.8%. Strength values exceed the ASTM minimum standard and are on par with ASM typical values, while elongation was substantially improved compared to 7 and 11% for the ASTM and ASM values respectively. Finally, it was observed that low temperature extrusion at 341 °C and 40 rpm gave superior material properties in the T6 condition compared to high temperature extrusion at 441 °C and 120 rpm due to variances in nanoscale second phase size and distribution.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Synthetic sea water - An improved stress corrosion test medium for aluminum alloys

A major problem in evaluating the stress corrosion cracking resistance of aluminum alloys by alternate immersion in 3.5 percent salt (NaCl) water is excessive pitting corrosion. Several methods were examined to eliminate this problem and to find an improved accelerated test medium. These included the addition of chromate inhibitors, surface treatment of specimens, and immersion in synthetic sea water. The results indicate that alternate immersion in synthetic sea water is a very promising stress corrosion test medium. Neither chromate inhibitors nor surface treatment (anodize and alodine) of the aluminum specimens improved the performance of alternate immersion in 3.5 percent salt water sufficiently to be classified as an effective stress corrosion test method.

Humphries, T. S.↗