Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additive Process Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Zr-Hf-Ta fractionation during lunar evolution

Zr/Hf ratios and other elemental data in 68 samples of various mare basalts, KREEP units, and lunar glasses have been determined using instrumental neutron activation analysis coupled with coincidence-anticoincidence counting for greater precision. The data are presented in order to quantify further the amount of Zr/Hf fractionation that has occurred during primordial crystallization and cumulate remelting or by any other process. Models of Zr-Hf evolution are developed to place additional constraints on the bulk lunar composition and on the effects of minor phases that may be responsible for the observed fractionations. The Hf-Ta fractionation in lunar compositions is also reviewed in order to characterize normal Hf(4+) versus Ta(4+) behavior and to delineate possible effects due to the oxidation of Ta(4+) to Ta(5+) during late-stage ilmenite crystallization.

Hughes, S. S.↗
NASA NTRS1993

The influence of the hydrologic cycle on the extent of sea ice with climatic implications

Multi-temporal satellite images, field observations, and field measurements were used to investigate the mechanisms by which sea ice melts offshore from the Mackenzie River delta. Advanced Very High Resolution Radiometer (AVHRR) satellite data recorded in 1986 were analyzed. The satellite data were geometrically corrected and radiometrically calibrated so that albedo and temperature values could be extracted. The investigation revealed that sea ice melted approximately 2 weeks earlier offshore from the Mackenzie River delta than along coasts where river discharge is minimal or non-existent. There is significant intra-delta variability in the timing and patterns of ice melt. An estimation of energy flux indicates that 30 percent more of the visible wavelength energy and 25 percent more of the near-infrared wavelength energy is absorbed by water offshore of the delta compared to coastal areas with minimal river discharge. The analysis also revealed that the removal of sea ice involves the following: over-ice-flooding along the coast offshore from river delta channels; under-ice flow of 'warm' river water; melting and calving of the fast ice; and, the formation of a bight in the pack ice edge. Two stages in the melting of sea ice were identified: (1) an early stage where heat is supplied to overflows largely by solar radiation, and (2) a later stage where heat is supplied by river discharge in addition to solar radiation. A simple thermodynamic model of the thaw process in the fast ice zone was developed and parameterized based on events recorded by the satellite images. The model treats river discharge as the source of sensible heat at the base of the ice cover. The results of a series of sensitivity tests to assess the influence of river discharge on the near shore ice are presented.

Dean, Kenneson G.↗
NASA NTRS1997

Existing and Required Modeling Capabilities for Evaluating ATM Systems and Concepts

ATM systems throughout the world are entering a period of major transition and change. The combination of important technological developments and of the globalization of the air transportation industry has necessitated a reexamination of some of the fundamental premises of existing Air Traffic Management (ATM) concepts. New ATM concepts have to be examined, concepts that may place more emphasis on: strategic traffic management; planning and control; partial decentralization of decision-making; and added reliance on the aircraft to carry out strategic ATM plans, with ground controllers confined primarily to a monitoring and supervisory role. 'Free Flight' is a case in point. In order to study, evaluate and validate such new concepts, the ATM community will have to rely heavily on models and computer-based tools/utilities, covering a wide range of issues and metrics related to safety, capacity and efficiency. The state of the art in such modeling support is adequate in some respects, but clearly deficient in others. It is the objective of this study to assist in: (1) assessing the strengths and weaknesses of existing fast-time models and tools for the study of ATM systems and concepts and (2) identifying and prioritizing the requirements for the development of additional modeling capabilities in the near future. A three-stage process has been followed to this purpose: 1. Through the analysis of two case studies involving future ATM system scenarios, as well as through expert assessment, modeling capabilities and supporting tools needed for testing and validating future ATM systems and concepts were identified and described. 2. Existing fast-time ATM models and support tools were reviewed and assessed with regard to the degree to which they offer the capabilities identified under Step 1. 3 . The findings of 1 and 2 were combined to draw conclusions about (1) the best capabilities currently existing, (2) the types of concept testing and validation that can be carried out reliably with such existing capabilities and (3) the currently unavailable modeling capabilities that should receive high priority for near-term research and development. It should be emphasized that the study is concerned only with the class of 'fast time' analytical and simulation models. 'Real time' models, that typically involve humans-in-the-loop, comprise another extensive class which is not addressed in this report. However, the relationship between some of the fast-time models reviewed and a few well-known real-time models is identified in several parts of this report and the potential benefits from the combined use of these two classes of models-a very important subject-are discussed in chapters 4 and 7.

Odoni, Amedeo R.↗
NASA NTRS1999

Novel Three-Dimensional Vertical Interconnect Technology for Microwave and RF Applications

In this paper, novel 3D interconnects suitable for applications in microwave and RF integrated circuit technology have been presented. The interconnect fabrication process and design details are presented. In addition, measured and numerically modeled results of the performance of the interconnects have been shown. The results indicate that the proposed technology has tremendous potential applications in integrated circuit technology. C,

Goverdhanam, Kavita↗
NASA NTRS2001

Tropical Rainfall Measuring Mission: Monitoring the Global Tropics for 3 Years and Beyond

The Tropical Rainfall Measuring Mission (TRMM) was launched in November 1997 as a joint U.S.-Japanese mission to advance understanding of the global energy and water cycle by providing distributions of rainfall and latent heating over the global tropics. As a part of NASA's Earth System Enterprise, TRMM seeks to understand the mechanisms through which changes in tropical rainfall influence global circulation. Additionally, a goal is to improve the ability to model these processes in order to predict global circulations and rainfall variability at monthly and longer time scales. Such understanding has implications for assessing climate processes related to El Nino/La Nina and Global Warming. TRMM has also provided unexpected and exciting new knowledge and applications in areas related to hurricane monitoring, lightning, pollution, hydrology, and other areas. This CD-ROM includes a self-contained PowerPoint presentation that provides an overview of TRMM and significant science results; a set of data movies or animation; and listings of current TRMM-related publications in the literature.

Shepherd, Marshall↗
NASA NTRS2018

Carbon-Nitrogen Coupling Under Three Schemes of Model Representation: A Traceability Analysis

The interaction between terrestrial carbon (C) and nitrogen (N) cycles has been incorporated into more and more land surface models. However, the scheme of C-N coupling differs greatly among models, and how these diverse representations of C-N interactions will affect C-cycle modeling remains unclear. In this study, we explored how the simulated ecosystem C storage capacity in the terrestrial ecosystem (TECO) model varied with three different commonly used schemes of C-N coupling. The three schemes (SM1, SM2, and SM3) have been used in three different coupled C-N models (i.e., TECO-CN, CLM 4.5, and O-CN, respectively). They differ mainly in the stoichiometry of C and N in vegetation and soils, plant N uptake strategies, down regulation of photosynthesis, and the pathways of N import. We incorporated the three C-N coupling schemes into the C-only version of the TECO model and evaluated their impacts on the C cycle with a traceability framework. Our results showed that all three of the C-N schemes caused significant reductions in steady-state C storage capacity compared with the C-only version with magnitudes of −23%, −30%, and −54% for SM1, SM2, and SM3, respectively. This reduced C storage capacity was mainly derived from the combined effects of decreases in net primary productivity (NPP; −29%, −15%, and −45%) and changes in mean C residence time (MRT; 9%, −17%, and −17%) for SM1, SM2, and SM3, respectively. The differences in NPP are mainly attributed to the different assumptions on plant N uptake, plant tissue C : N ratio, down regulation of photosynthesis, and biological N fixation. In comparison, the alternative representations of the plant vs. microbe competition strategy and the plant N uptake, combined with the flexible C : N ratio in vegetation and soils, led to a notable spread in MRT. These results highlight the fact that the diverse assumptions on N processes represented by different C-N coupled models could cause additional uncertainty for land surface models. Understanding their difference can help us improve the capability of models to predict future biogeochemical cycles of terrestrial ecosystems.

Du, Zhenggang↗
NASA NTRSDate not supplied

Geometric Sensitivity of Residual Fields in Metal Additive Manufacturing

The sensitivity of geometrical parameters on the residual stress and distortion as computed by a metal additive manufacturing simulation is presented. A nozzle-like geometry was chosen with its length, wall thickness, and outer radius varied. A Latin hypercube sampling of 300 specimens produced the combinations of the geometrical parameters. Full thermomechanical simulations predicted the residual fields. Statistical analysis including regression curves shows that there is a strong correlation between these residual fields and the geometry, hinting that it may be possible to predictably influence the residual displacements and residual stresses by varying the overall geometry.

Multiscale Modeling↗
NASA NTRS2023

Technical Note: NASAaccess – A Tool for Access, Reformatting, and Visualization of Remotely Sensed Earth Observation and Climate Data

The National Aeronautics and Space Administration (NASA) has launched a new initiative, the Open-Source Science Initiative (OSSI), to enable and support science towards openness. The OSSI supports open-source software development and dissemination. In this work, we present NASAaccess, which is an open-source software package and web-based environmental modeling application for earth observation data accessing, reformatting, and presenting quantitative data products. The main objective of developing the NASAaccess platform is to facilitate exploration, modeling, and understanding of earth data for scientists, stakeholders, and concerned citizens whose objectives align with the new OSSI goals. The NASAaccess platform is available as software packages (i.e., the R and conda packages) as well as an interactive-format web-based environmental modeling application for earth observation data developed with Tethys Platform. NASAaccess has been envisioned as lowering the technical barriers and simplifying the process of accessing scalable distributed computing resources and leveraging additional software for data and computationally intensive modeling frameworks. Specifically, NASAaccess has been developed to meet the need for seamless earth observation remote-sensing and climate data ingestion into various hydrological modeling frameworks. Moreover, NASAaccess is also contributing to keeping interested parties and stakeholders engaged with environmental modeling, accessing the information available in various remote-sensing products. NASAaccess' current capabilities cover various NASA datasets and products that include the Global Precipitation Measurement (GPM) data products, the Global Land Data Assimilation System (GLDAS) land surface states and fluxes, and the NASA Earth Exchange Global Daily Downscaled Projections (NEX-GDDP) Coupled Model Intercomparison Project Phase 5 (CMIP5) and Coupled Model Intercomparison Project Phase 6 (CMIP6) climate change dataset products.

Ibrahim Nourein Mohammed↗
NASA NTRSDate not supplied

Acoustic Testing of the Joby Aviation Propeller in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel

The advanced air mobility sector has progressed in recent years with electric vertical take-Off and landing vehicles at the forefront. In response, the NASA Advanced Air Mobility Project has initiated the Advanced Air Mobility National Campaign to partner with industry to progress this emerging market. This resulted in NASA’s Revolutionary Vertical Lift Technology project to participate to progress research efforts for software tool validation for these advanced air mobility vehicle configurations. Noise has been identified as one of the main obstacles to succeeding in this emerging market for community acceptance. To further understand electric vertical take-Off and landing vehicle noise, an isolated Joby Aviation S4 propeller was tested in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel to aid in providing high quality performance, loads, and acoustic data. Details of test hardware and setup are described with a focus on acoustics, which includes facility, test model, microphone locations, and data acquisition system details. Additionally, the data processing techniques and completed test matrix for acoustic points are provided. To aid in identifying potential acoustic reflections, an acoustic reflection test was performed prior to the start of the test and highlighted the presence of reflections at every microphone location. Acoustic results are provided for various flight regimes for sweeps of blade pitch, RPM, flow angle, and wind speed. These results show an optimum RPM for a specific thrust level for noise, and further reductions in RPM can increase noise levels. This dataset will be used to evaluate and improve computational tools.

Aviation Propeller↗
DOE OSTI2024

Photoneutron Production Using an Electron Linear Accelerator for Applications in Neutron Imaging

Photoneutron production is possible using an electron linear accelerator and a target capable of generating photonuclear reactions. A short pulse neutron source can be useful for neutron imaging dynamic experiments. This study is aimed at the feasibility of photoneutron production using a 20 MeV electron linear accelerator and tungsten and depleted uranium targets of various thicknesses. MCNP6 (Monte Carlo N-Particle) code will be used to develop a computational model to estimate total neutron yield, and this will be verified at the Idaho State University’s Accelerator Center. After verification of the neutron yield and energy spectra, an additional MCNP6 model will be developed to analyze the neutron imaging processes. This study will potentially prove it is possible to conduct multi-mode imaging experiments on the anticipated Scorpius electron linear accelerator at the Nevada National Security Sites.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Assessment of Buffer-IPyC Thermomechanical Debonding Behavior Using New Experiment Strength Data in BISON

TRIstructural ISOtropic (TRISO) single sub-millimeter-diameter nuclear fuel particle consists of a spherical fuel kernel surrounded by four coating layers. During reactor operation, the TRISO coating layers are subjected to irradiation-induced dimensional changes and the associated thermomechanical behavior of each layer. One of the observed behaviors is gap formation between the buffer and IPyC layer due to the porous buffer’s irradiation-induced shrinkage exceeding that of the IPyC layer. To predict TRISO thermomechanical performance, multi-physics models have been built that are continually updated and refined. The BISON code is a finite element-based nuclear fuel performance code that may be used for TRISO particle simulations. One of the recent additions to the BISON code is the ability to model the process of layer debonding. This paper will focus on the simulation results of the improved BISON debonding model that will utilize updated strengths measured from irradiated TRISO fuel particles. The new experimental strength data from micromechanical tests of irradiated TRISO fuel samples were exercised in the BISON simulations and compared to baseline strength data to assess their applicability in the models. This also includes updated buffer-IPyC bond strengths to simulate layer delamination. Based on current experimental observations it is noted that the buffer-IPyC separation occurs not exactly at the junction of these two layers, but more on the side of the buffer layer. This improved modeling approach using experimental strength data to characterize buffer-IPyC debonding and its potential subsequent cracking will be presented in the paper along with comparisons to available experimental observations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessment of buffer-IPyC thermomechanical debonding behavior using new experimental strength data in BISON

TRIstructural ISOtropic (TRISO) fuel is a nuclear fuel commonly used in High Temperature Gas-cooled Reactors (HTGRs). A single sub-millimeter-diameter TRISO fuel particle consists of a spherical fuel kernel surrounded by four coating layers: a low-density pyrocarbon buffer layer, an inner pyrolytic carbon (IPyC) layer, a silicon carbide (SiC) layer, and an outer pyrolytic carbon (OPyC) layer. The kernel is commonly made of UO2 or a mixture of uranium carbide and uranium oxide (UCO). During reactor operation, the TRISO coating layers are subjected to irradiation-induced dimensional changes and the associated thermomechanical behavior of each layer. One of the observed behaviors is gap formation between the buffer and IPyC layer due to the porous buffer’s irradiation-induced shrinkage exceeding that of the IPyC layer. Not all irradiated particles will experience buffer-IPyC gap formation. The debonding may be partial, or it may be nearly total. However, from post-irradiation examination of UCO TRISO fuels irradiated as part of the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program, it was concluded that partial buffer-IPyC debonding was the most common type of buffer-IPyC interaction. To predict TRISO thermomechanical performance, multi-physics models have been built that are being continually updated and refined. The BISON code is a finite element-based nuclear fuel performance code that may be used for 1D, 2D, and 3D TRISO particle simulations. This code is used to calculate fuel temperature, kernel swelling, buffer densification, thermal and irradiation creep, fracture, and fission gas production and release. One of the recent additions to the BISON code is the ability to model the process of layer debonding. This paper will focus on the simulation results of the improved BISON debonding model that will utilize updated strengths measured from irradiated AGR TRISO fuel particles. The new experimental strength data from micromechanical tests of irradiated TRISO fuel samples were exercised in the BISON simulations and compared to baseline strength data to assess their applicability in the models. This also includes updated buffer-IPyC bond strengths to simulate layer delamination. Based on current experimental observations it is noted that the buffer-IPyC separation occurs not exactly at the junction of these two layers, but more on the side of the buffer layer. That observation is also implemented in the TRISO interface debonding model. This improved modeling approach using experimental strength data to characterize buffer-IPyC debonding and its potential subsequent cracking will be presented in the paper along with comparisons to available experimental observations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRSDate not supplied

Artificial Intelligence (AI) Methods for Augmenting the IMPACT Tool Evidence Library

Development of the Evidence Library for use with the IMPACT probability risk assessment tool took several years and involved a staggering amount of effort from a multi-disciplinary team. A very significant amount of the labor effort to collect, assess and finalize the Clinical Finding Form (CliFF) for each of the 119 medical conditions was provided by physician subject matter experts from the Exploration Medical Capability (ExMC) Element Clinical and Science Team. Many AI tools such as ChatGPT are excellent at summarizing large amounts of information and the current project was initiated to determine how such tools might streamline laborious processes, e.g., review and summarization of many scientific research publications, to execute key steps more efficiently in the process of developing CliFFs. The process for collecting the evidence which is found in the CliFFs is well documented in the Evidence Library Methods document (ELM; HRP-48036*). Using ELM and the CliFF development instructions as a guideline, a team of developers is leveraging Microsoft Azure AI tools and services along with open-source frameworks, to construct an AI-assisted automated pipeline. This pipeline is designed to search, retrieve, and process the necessary data sources, and ultimately help generate the final version of a CliFF. Currently, the large language model evaluates the relevance of each source material to spaceflights, either as direct evidence or as an analog. Additionally, the model assists in extracting keywords and generating brief summaries to enhance augmented retrieval and search processes in later stages of CliFF development. Once the data is ready, the model can perform semantic search and retrieval, generating and extracting valuable information for the CliFF. For instance, it can handle epidemiological statistical data, such as incidence rates and the likelihood of best or worst-case scenarios. The steps that required reading and summarizing articles were viewed as providing the greatest return on investment since large language models are very efficient and accurate in summarizing large amounts of text. Since labor effort to complete the original CliFF was not recorded with sufficient granularity, comparisons with an AI tool-generated CliFF will provide merely an approximation of time saved. Upon completion of the process, the CliFF for the medical condition “appendicitis” generated with the support of AI-based methods will serve as a proof-of-concept and will be compared to the original appendicitis CliFF to determine if use of the tools resulted in content and conclusory similarity. Based upon the results from face validation of the two CliFFs, modifications to the process will be made if necessary and additional condition CliFFs will be evaluated. Ultimately, CliFFs for the entire set of medical conditions will be created with the assistance of AI tools. Depending on the cost savings realized, CliFFs for additional medical conditions can be created to expand the Evidence Library. Future direction includes specifying the characteristics of the reviewer (prompting the AI tools to generate output assuming the reviewer is a sub-specialist physician, or nurse or EMT/medic) to determine if the effects on AI-generated output are different based on knowledge, skills and abilities. *Exploration Medical Capability Evidence Library Methods, HRP-48036 Rev A, July 2022.

Ali Al↗
DOE OSTI2025

Enhancing Gaussian Process Surrogates for Optimization and Posterior Approximation via Random Exploration

This paper proposes novel noise-free Bayesian optimization strategies that rely on a random exploration step to enhance the accuracy of Gaussian process surrogate models. The new algorithms retain the ease of implementation of the classical GP-UCB algorithm, but the additional random exploration step accelerates their convergence, nearly achieving the optimal convergence rate. Furthermore, to facilitate Bayesian inference with intractable likelihoods, we propose to utilize optimization iterates for maximum a posteriori estimation to build a Gaussian process surrogate model for the unnormalized log-posterior density. We provide bounds for the Hellinger distance between the true and the approximate posterior distributions in terms of the number of design points. We demonstrate the effectiveness of our Bayesian optimization algorithms in nonconvex benchmark objective functions, in a machine learning hyperparameter tuning problem, and in a black-box engineering design problem. The effectiveness of our posterior approximation approach is demonstrated in two Bayesian inference problems for parameters of dynamical systems.

Bayesian inference↗
DOE OSTI2021

AI-Batt (Autonomous Identification of Battery Life Models) [SWR 21-36]

Autonomous Identification of Battery Life Models (AI-Batt) AI-Batt is a MATLAB code base for developing lifetime models for batteries from accelerated aging data. The code base provides many functions for processing, visualizing, and modeling battery aging data, making the data processing, exploration, and modeling workflow substantially faster. These tools are tailored for working with battery aging data sets, which usually consist of many separate time-series for each cell, with many test conditions and possible replicates at each condition, which makes it difficult to simply process or visualize the data set. Complex modeling tasks, such as cross-validation, sensitivity analysis, and uncertainty quantification have been implemented to enable thorough statistical investigation of model predictions. Additionally, several machine-learning algorithms are implemented to autonomously identify suitable models via symbolic regression. Data processing functions automatically cast data from the struct data type, which is commonly used to store experimental data, but is not an acceptable input for most algorithms, to the table data type, which can be easily used as input to any optimization algorithm. Also, the data can be separated into time-invariant and time-variant data tables, which is helpful for exploring the data set as well as developing separate models for time-variant and time-invariant aging mechanisms. For example, in aging tests with constant temperature, temperature is a time-invariant experimental condition. Visualization tools enable plotting of data, model fits, and model simulations possible with single-line function calls, empowering data exploration of complex data sets with both time-varying and time-invariant trends. Plots can be automatically generated for the whole data set, or separated by data group (groups of test replicates) or individual data series. Data points or data series can be automatically colored by the value of a variable with a variety of color maps, and model predictions can also be colored by the value of a fit statistic. Comparisons between data sets and the predictions/simulations of different models on the same data set can be easily plotted as well. Distributions of parameter values from bootstrap resampling can be plotted to visualize the reliability of parameter estimation, or determine any correlations between parameters. Modeling tools handle the complex task of creating and parsing symbolic equations for modeling battery lifetime. Equations are parsed to grab relevant data variables, parameter values, or specified sub-models for input into optimization, evaluation, or simulation functions. Models can be optimized locally (one set of parameters for each data series), bi-level (some parameters shared across the data set), or globally (single set of parameters for all data). Functions implementing symbolic regression algorithms help users to discover effective model equations, even in poorly sampled, high-dimensional data.

Smith, Kandler [National Renewable Energy Lab. (NR↗
NASA NTRS1993

An extended supersonic combustion model for the dynamic analysis of hypersonic vehicles

The development of an advanced dynamic model for aeroelastic hypersonic vehicles powered by air breathing engines requires an adequate engine model. This report provides a discussion of some of the more important features of supersonic combustion and their relevance to the analysis and design of supersonic ramjet engines. Of particular interest are those aspects of combustion that impact the control of the process. Furthermore, the report summarizes efforts to enhance the aeropropulsive/aeroelastic dynamic model developed at the Aerospace Research Center of Arizona State University by focusing on combustion and improved modeling of this flow. The expanded supersonic combustor model described here has the capability to model the effects of friction, area change, and mass addition, in addition to the heat addition process. A comparison is made of the results from four cases: (1) heat addition only; (2) heat addition plus friction; (3) heat addition, friction, and area reduction, and (4) heat addition, friction, area reduction, and mass addition. The relative impact of these effects on the Mach number, static temperature, and static pressure distributions within the combustor are then shown. Finally, the effects of frozen versus equilibrium flow conditions within the exhaust plume is discussed.

Bossard, J. A.↗
DOE OSTI2024

Influence of alloy solidification path on melt pool behavior in additive manufacturing

Numerical models used to study transport phenomena in laser-powder bed fusion processes often rely on assumptions and simplifications to reduce their computational expense. One common simplification is in the description of latent heat evolution during the solid-liquid phase change (i.e., the solidification pathway), justified by the fact that the mushy zone thickness is similar to the numerical grid spacing used for continuum transport models. The lack of resolution of transport phenomena in the mushy zone motivates the use of computationally convenient solidification paths such as linear or sigmoidal relationships over pathways derived from fundamental solidification theory such as equilibrium or Scheil models. In the present work, an uncertainty quantification (UQ) framework is used to analyze the influence of solidification pathway selection on the solidification dynamics and melt pool geometries in laser based additive manufacturing (AM) of IN625. Results show the solidification pathway has a quantifiable influence on the cooling rate at the liquidus isotherm, mushy zone thickness, and solidification time. Due to similarities in the latent heat evolution at the beginning of solidification, the equilibrium and Scheil models predict similar cooling rates near the liquidus isotherm, however the wider freezing range of Scheil leads to a wider mushy zone compared to equilibrium. The non-physical latent heat release profiles of sigmoidal and linear paths lead to significant overpredictions of cooling rates at the liquidus isotherm compared to equilibrium and Scheil. Finally, these results indicate that careful consideration should be given to the choice of solidification pathway to ensure reliable model predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesis, Processing, and Use of Isotopically Enriched Epitaxial Oxide Thin Films

Isotopic engineering has emerged as a key approach to study the nucleation, diffusion, phase transitions, and reactions of materials at an atomic level. It aims to uncover mass transport pathways, kinetics, and operational and failure mechanisms of functional materials and devices. Understanding these phenomena leads to deeper insights into important physical processes, such as the transport of ions in energy conversion and storage devices and the role of active sites and supports during heterogeneous catalytic reactions. Likewise, isotopic engineering is being pursued as a means of modifying functionality to enable future technological applications. In this Account, we summarize our recent work employing isotope labeling (e.g., 18 O 2 and 57 Fe) during thin film synthesis and postgrowth processing to reveal growth mechanisms, defect chemistry, and elemental diffusion under working and extreme conditions. Isotope-resolved analysis techniques with nanometer-scale spatial resolution, such as time-of-flight secondary ion mass spectrometry and atom probe tomography, facilitate the accurate quantification of isotopic placement and concentration in our well-defined heterostructures with precisely positioned, isotope-enriched layers. By measuring the nanometer-scale redistribution between natural abundance and isotopically enriched oxygen layers during the deposition of Fe 2 O 3 and Cr 2 O 3 by molecular beam epitaxy, we identified intermixing processes driven by surface adatoms occurring both at the film growth surface and within the first few layers below the surface. Further insights into synthesis mechanisms were gained by studying the tungsten oxide thin films grown by evaporating WO 3 powder in the presence of background 18 O 2 , revealing minimal incorporation of background oxygen during the film formation process. Thermal and radiation-enhanced diffusion in epitaxial Fe and Cr oxides were precisely tracked using 18 O and 57 Fe tracer layers incorporated into model epitaxial oxide thin films. This approach has allowed us to access thermal diffusion behavior at lower temperatures than previously measured, revealing a potential changeover in diffusion mechanism. Understanding radiation-enhanced diffusion in model oxides that represent the surface layers on the structural components of nuclear reactors informs our understanding of their corrosion behavior under irradiation. Isotopic labeling can also provide unique insights into the surface exchange reactions and defect chemistry of electrocatalysts. For instance, tracking the change in 18 O concentration at the surface of an epitaxial LaNiO 3 thin film after the electrocatalytic oxygen evolution reaction revealed the participation of lattice oxygen, confirming a hypothesis that had been proposed previously. Lastly, we highlight a new direction wherein we perform in situ processing studies utilizing isotopic tracers in conjunction with model epitaxial thin films within the atom probe tomography instrument. Additionally, this Account illustrates the great potential of isotopic engineering to enable fundamental mechanistic insights into physical processes and engineer functional properties in epitaxial films, heterostructures, and superlattices.

36 MATERIALS SCIENCE↗