Search NASA⌕ Search

SEARCH · Search NASA

Results for “Air Sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Speciation mapping of the oxidation layer on aged uranium dioxide using scanning transmission x-ray spectromicroscopy

In this study, UO 2 was aged in humid air and prepared as a thin section using a focused ion beam (FIB) instrument. The specimen was measured using synchrotron radiation spectromicroscopy techniques at the Beamline 11.0.2 STXM end station of the Advanced Light Source (ALS). Non-negative matrix factorization (NMF) methods were used to identify and map three component x-ray absorption near-edge structure (XANES) spectra in the oxygen K-edge data, revealing a surface layer of U 4 O 9 with a thickness of 206 ± 21 nm, and the bulk of the sample remaining as UO 2 . Uranium N 4,5 -edge XANES spectromicroscopy supports these results. The diffusion-controlled parabolic rate constant for UO 2 oxidation to U 4 O 9 was calculated from the observed layer thickness and compared to literature values. Complementary transmission electron microscopy (TEM) was used to image the sample and identify the phases present in various regions, confirming the STXM results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Imaging nanomagnetism and magnetic phase transitions in atomically thin CrSBr

Since their first observation in 2017, atomically thin van der Waals (vdW) magnets have attracted significant fundamental, and application-driven attention. However, their low ordering temperatures, T c , sensitivity to atmospheric conditions and difficulties in preparing clean large-area samples still present major limitations to further progress, especially amongst van der Waals magnetic semiconductors. The remarkably stable, high-T c vdW magnet CrSBr has the potential to overcome these key shortcomings, but its nanoscale properties and rich magnetic phase diagram remain poorly understood. Here we use single spin magnetometry to quantitatively characterise saturation magnetization, magnetic anisotropy constants, and magnetic phase transitions in few-layer CrSBr by direct magnetic imaging. We show pristine magnetic phases, devoid of defects on micron length-scales, and demonstrate remarkable air-stability down the monolayer limit. We furthermore address the spin-flip transition in bilayer CrSBr by imaging the phase-coexistence of regions of antiferromagnetically (AFM) ordered and fully aligned spins. Our work will enable the engineering of exotic electronic and magnetic phases in CrSBr and the realization of novel nanomagnetic devices based on this highly promising vdW magnet.

36 MATERIALS SCIENCE↗
DOE OSTI2026

1996 Bay Area Travel Study Wave 2

The 1996 Bay Area Travel Study, conducted by the Metropolitan Transportation Commssion, collected demographic, socioeconomic, and travel data for 3,618 households in California's nine-county Bay Area: Alameda, Contra Costa, Marin, Napa, San Francisco, San Mateo, Santa Clara, Solano, and Sonoma counties. The goal of the study was to collect information on activities for all people in each household, regardless of age or relationship. Respondents were asked to record all activities, including trips, over a two-day period. The data gathered during the survey will be used for the area's long-term transportation and air quality planning needs. The survey collected both weekday and weekend multi-day data and was the first activity-based survey conducted in the Bay Area. It also included separate sub-projects. A stated preference congestion pricing survey was administered to 150 of the respondents with a follow-up survey conducted with 110 participants. A follow-up survey was also completed by over half of the 3,618 respondent households to update contact and demographic information. These participants were then used as a panel sample for the 2000 Bay Area Travel Survey (NuStats Research and Consulting 1999).

1Hz data↗
DOE OSTI2024

End-Use Savings Shapes Upgrade Package Documentation: LED Lighting, HP-RTU and ASHP-Boiler

Building on the successfully completed effort to calibrate and validate the U.S. Department of Energy's ResStock and ComStock models over the past 3 years, the objective of this work is to produce national data sets that empower analysts working for federal, state, utility, city, and manufacturer stakeholders to answer a broad range of analysis questions. The goal of this work is to develop energy efficiency, electrification, and demand flexibility end-use load shapes (electricity, gas, propane, or fuel oil) that cover a majority of the high-impact, market-ready (or nearly market-ready) upgrade measures, or upgrades. "Measures" refers to energy efficiency variables that can be applied to buildings during modeling. An end-use savings shape is the difference in energy consumption between a baseline building and a building with an energy efficiency, electrification, or demand flexibility upgrade applied. It results in a time-series profile that is broken down by end use and fuel (electricity or on-site gas, propane, or fuel oil use) at each time step. ComStock is a highly granular, bottom-up model that uses multiple data sources, statistical sampling methods, and advanced building energy simulations to estimate the annual subhourly energy consumption of the commercial building stock across the United States. The baseline model intends to represent the U.S. commercial building stock as it existed in 2018. The methodology and results of the baseline model are discussed in the final technical report of the End-Use Load Profiles project. This documentation focuses on an upgrade package of three end-use savings shapes upgrades - Light Emitting Diode (LED) Lighting, Heat Pump Rooftop Unit (RTU) (HP-RTU), and Air-Source Heat Pump (ASHP) Boiler, which we will refer to collectively as the "Interior Lighting and Heat Pump" package. More details on the individual upgrades can be found on the ComStock Measures Documentation page. An upgrade package applies two or more EUSS upgrades to a single building model simulation. Since ComStock is a bottom-up physics-based model, an upgrade package will go beyond aggregating or summing the individual upgrade results and produce novel results by simulating interactions between the upgrades. For example, pairing an envelope upgrade with an electrification upgrade would likely result in higher savings results than the sum of these upgrades individually, and the size of the heating, ventilating, and air conditioning (HVAC) equipment may be reduced if the envelope upgrade reduces the loads significantly.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Phase Transformation and Water Adsorption Behavior of As‐Deposited and Annealed Ru Metal Thin Films Prepared by Atomic Layer Deposition

ABSTRACT Surfaces play a central role in catalytic processes, and understanding the transformation of ruthenium metal into ruthenium oxide during annealing is essential for tailoring functional catalytic interfaces. In this study, we systematically investigate ≈22 nm thick Ru metal films deposited by atomic layer deposition (ALD) at 300°C, focusing on their chemical composition, structural evolution, and surface hydration behavior following post‐deposition annealing in air from 400 to 600°C. Lab‐based and synchrotron X‐ray photoelectron spectroscopy (XPS) reveal a gradual conversion from metallic Ru to fully oxidized Ru 4+ with increasing annealing temperature, accompanied by a corresponding increase in lattice oxygen. X‐ray diffraction (XRD) shows amorphous Ru oxide phases at 400°C and 500°C that evolve into crystalline RuO 2 at 600°C, while atomic force microscopy (AFM) indicates enhanced grain growth and surface roughening upon annealing. Ambient‐pressure XPS (AP‐XPS) under controlled H 2 O vapor environments (1–17 Torr) demonstrates that samples annealed at 400°C and 500°C exhibit initially high hydroxyl coverage that decreases with increasing water vapor pressure, concurrent with a rise in molecular H 2 O adsorption. In contrast, the crystalline RuO 2 surface formed at 600°C maintains stable hydroxylation and supports increased water uptake. Overall, this work provides fundamental insight into Ru oxide–H 2 O interactions and establishes design principles for engineering oxide surfaces optimized for electrocatalytic applications.

APXPS↗
DOE OSTI2025

GreenSight WxHive Unmanned Aerial System (UAS) Atmospheric Profiling at the SGP Central Facility

The GreenSight WxHive is capable of flying multiple nanodrones simultaneously to provide spatiotemporal atmospheric sampling. During the WH2yMSIE campaign, the WxHive would fly up to 5 nanodrones at once, performing profiling within the planetary boundary layer over the ARM SGP Central Facility site. The measurements provided by the WxHive include latitude, longitude, altitude, pressure, temperature, humidity, and wind speed and direction. See the attached WeatherHive User Guide for more details about the instrument and measurements.

Air pressure↗
DOE OSTI2025

Nanoscale control of LaAlO 3 /SrTiO 3 conductance beyond the polar catastrophe

Conductive atomic force microscope (c-AFM) lithography can be utilized to create a wide range of LaAlO 3 /SrTiO 3 (LAO/STO)-based nanoelectronic devices in a reconfigurable manner. Experiments were generally performed with intrinsically insulating LAO/STO heterostructures, with LAO thickness less than the critical value at which a polar catastrophe takes place [<4 unit cell (u.c.)]. Here, we use inductively coupled plasma reactive ion etching (ICPRIE) to fabricate c-AFM “canvases” on intrinsically conducting LAO/STO samples with ≥4 u.c. LAO. We observe that its interfacial two-dimensional electron gas (2DEG) can be pinched off and then switched back on by c-AFM lithography. Nanowires created with initially conductive LAO/STO interfaces have an order-of-magnitude longer lifetime in ambient conditions, when compared to an identically created 3.4 u.c. LAO/STO nanowire. We also demonstrate key nanoscale properties such as ballistic transport in a quasi-one-dimensional electron waveguide at a 5 u.c. LAO/STO interface. This approach frees c-AFM-written nanodevice designs from time constraints in air associated with <4 u.c. LAO/STO heterostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

PM2.5 Active Aerosol Collection Field Campaign Report

The long-range transport of aerosols can affect local air quality as well as contribute elements and constituents to mountain watersheds that have potentially positive (e.g., nitrate) and negative (e.g., heavy metals) effects to the local ecosystem. Isotopic analysis of aerosols can be a powerful tool for deconvolving the relative contributions of far-distant and local sources to the composition of collected aerosols. Our field campaign involved the week-long collection of PM2.5 (i.e., particulate matter with an aerodynamic diameter of about 2.5 microns) aerosols on filters, which were returned to the laboratories at Lawrence Berkeley National Laboratory (LBNL) for analysis. The sampling sites were located at the Gothic, Colorado Surface Atmosphere Integrated Field Laboratory (SAIL) Atmospheric Radiation Measurement (ARM) and the Mt. Crested Butte, Colorado SAIL ARM sites. The original intention was to measure the lead (Pb) and strontium (Sr) isotopic compositions of the collected aerosols at high precision to provide constraints on source portioning and attribution, as well as analyze the chemical compositions and nitrogen and carbon isotopic compositions. However, severe blank issues arose that prevented the planned isotopic analyses of Sr, Pb, C, and N and severely affected the analyses of the bulk chemical compositions of the collected aerosols, resulting in the failure of the study. The issue is described in Section 2.0.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Demonstration and characterization of insertable passive thermal switches for dynamic building envelopes

A dynamic building envelope integrated with thermal energy storage, such as phase change material (PCM), is an emerging technology that offers a promising solution to improve the energy efficiency of buildings. This study reports the development of insertable thermal switches, which modulate thermal resistance, thereby making building envelopes dynamic and enhancing the use of free ambient heating and cooling. The reported thermal switches are passive, meaning they work solely based on indoor and outdoor temperatures. A single switch when inserted into 10 × 10-in (0.064-m 2 ) XPS foam board insulation demonstrates effective thermal conductivity of 0.050 W/m-K in the resistive state and 0.285 W/m-K in the conductive state. Thermal switches exhibit an effective switching ratio of 5.7, with no noticeable degradation in performance over 770 cycles. Additionally, when integrated into a wall sample containing a PCM layer, switches significantly reduce the PCM solidification time by 43.2% during the cooling process.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

ResStock Measure Documentation: Residential Two-Stage Geothermal Heat Pump (4.0 COP, 20.5 EER) With Envelope Improvements and Advanced Air Sealing

The goal of this work is to develop energy efficiency, demand flexibility, and other retrofit end-use load shapes (electricity, gas, propane, or fuel oil) that cover a majority of the high-impact, market-ready (or nearly market-ready) measures. "Measures" refers to retrofits that can be applied to buildings during modeling. An "end-use savings shape" is the difference in energy consumption between a baseline building and a building with an energy efficiency, demand flexibility, or other retrofit measure applied. It results in a time-series profile that is broken down by end use and fuel (electricity or on-site gas, propane, or fuel oil use) at each time step. ResStock is a highly granular, physics-based, bottom-up model that uses multiple data sources, statistical sampling methods, and advanced building energy simulations to estimate the annual subhourly energy consumption of the residential building stock across the United States. The baseline model intends to represent the U.S. residential building stock as it existed in 2018. Technical documentation for the inputs and assumptions in the baseline building stock model is available in Reyna et al. (2025). Calibration and validation of the baseline model results are available in the final technical report of the End-Use Load Profiles project (Wilson, et al. 2022). This document focuses on a single end-use savings shape measure: Residential Two-Stage Geothermal Heat Pump (GHP) (4.0 COP, 20.5 EER) With Envelope Improvements. This measure combines a two-stage GHP with envelope improvements as a single package. As this package is a combination of two other measures, this document focused on documenting the results associated with this combination of technologies, with individual measure documents for two-stage GHPs and envelope improvements providing the information on the details of these measures. When the two technologies are combined, envelope improvements can modestly reduce energy consumption by a further 10%-15%, but also reduce the required size of the ground heat exchanger and heat pump by approximately 33% on average across all sites. The cost of installing envelope improvements in these homes is likely to be more than paid for by the reduction in equipment and drilling costs in these buildings for the majority of the stock.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗
DOE OSTI2025

Detecting Reactive Products in Carbon Capture Polymers with Chemical Shift Anisotropy and Machine Learning

Aminopolymers are attractive sorbents for CO 2 direct air capture applications due to their high density of amine groups, which can readily react with atmospheric levels of CO 2 to form chemisorbed species. The identity of these chemisorbed species and the functional groups that form upon oxidative degradation depends on both material properties and processing conditions, forming a variety of carbonyl-type sites such as ammonium carbamates, bicarbonates, carbonates, carbamic acids, ureas, and amides. 13 C solid-state nuclear magnetic resonance (NMR) is often used to help elucidate the identity of these reacted species, but it is challenging due to the narrow chemical shift range of carbonyl sites. Herein, we demonstrate the application of a two-dimensional (2D) chemical shift anisotropy (CSA) recoupling pulse sequence (ROCSA) to obtain CSA tensor values at each isotropic chemical shift, overcoming limitations of isotropic peak resolution. CSA tensor values describe the local chemical environment and can readily differentiate between the chemisorbed and degradation products. To aid identification, we also developed a k-nearest neighbor (kNN) classification model to distinguish the functional groups via their CSA tensor parameters. This methodology was demonstrated on poly(ethylenimine) in γ-Al 2 O 3 exposed to CO 2 and showed that the chemisorbed products are ammonium carbamate and a mixed carbamate–carbamic acid species. The sample was analyzed again after desorption at 100 °C inducing mild degradation, and the remaining products were strongly bound carbamate and urea species. In conclusion, the combination of 2D CSA measurements coupled with a kNN classification model enhances the ability to accurately identify chemisorbed or degradation products in complex carbon capture materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Evolution of Dissipative Regimes in Atomically Thin Bi 2 Sr 2 CaCu 2 O 8 + x Superconductor

Thermoelectric transport is widely used to study Abrikosov vortex dynamics in unconventional superconductors. However, only a few thermoelectric studies have been conducted near the dimensional crossover that occurs when the vortex-vortex interaction length scale becomes comparable to the sample size. Here, the effects of finite size on the dissipation mechanisms of the Nernst effect in the optimally doped Bi 2 Sr 2 CaCu 2 O 8 + x high-temperature superconductor are reported, down to the atomic length limit. To access this regime, a new generation of thermoelectric chips based on silicon nitride microprinted circuit boards is developed. These chips ensure optimized signals while preventing sample deterioration. The results demonstrate that lateral confinement at the nanoscale can effectively reduce vortex dissipation. Investigating vortex dissipation at the micro- and nano-scale is essential for creating stable, miniaturized superconducting circuits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Data for "Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells"

Back contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl2 treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO3 using a combination of angle-resolved XPS and the cadmium modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO3 native oxide. The fate of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO3 alleviates the downward band bending by 40 meV from 470 meV to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy which shows losses in internal open circuit voltage (iVoc) from 820 meV to 795 meV, carrier lifetime from 123 ns to 45 ns, and PL quantum yield from 2.9x10-5 to 1.2x10-5. Modeling time-resolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗
DOE OSTI2024

Enhancing physicochemical, bioactive, and nutritional properties of sweet potatoes: Ultrasonic contact drying with slot jet nozzles compared to hot-air drying and freeze drying

Sweet potatoes are a rich source of nutrients and bioactive compounds, but their quality can be impacted by the drying process. This study investigates the impact of slot jet reattachment (SJR) nozzle and ultrasound (US) combined drying (SJR + US) on sweet potato quality, compared to freeze-drying (FD), SJR drying, and hot air drying (HAD). SJR + US drying at 50 °C closely resembled FD in enhancing quality attributes and outperformed HAD and SJR in key areas such as rehydration, shrinkage ratios, and nutritional composition. Notably, SJR + US at 50 °C produced the highest total starch (36.84 g/100 g), total dietary fiber (8.48 g/100 g), total phenolic content (158.19 mg GAE/100 g), total flavonoid content (119.08 mg QE/g), DPPH antioxidant activity (6.44 μmol TE/g), β-carotene (31.98 mg/100 g), and vitamin C (5.27 mg/100 g). It also exhibited higher glass transition temperatures (Tg: 14.49 °C), indicating better stability at room temperature. The hardness values for SJR + US samples were similar to FD, while HAD samples had the highest hardness. SJR + US at 50 °C resulted in the lowest total color changes (ΔE), indicating minimal impact on appearance. Additionally, FTIR analysis revealed that peaks in specific spectral regions indicated superior preservation of bioactive compounds in SJR + US samples compared to other methods, which was also confirmed by principal component analysis (PCA) and heatmap visualization. Overall, these findings suggest that SJR + US is an effective alternative to conventional drying techniques, significantly improving the quality of dried sweet potatoes.

Color↗
DOE OSTI2024

Aircraft Measurements from a U.S. Western Wildfire Demonstrating Day and Night Differences in the Chemical Composition and Optical Properties of Biomass Burning Aerosols and Their Atmospheric Evolution

The composition and transformations of biomass burning aerosols (BBA) have been measured onboard the NOAA Twin Otter research aircraft during the Fire Influence on Regional to Global Environments and Air Quality field study. Here, we analyze real-time aerosol mass spectrometry measurements across three flights during the afternoon, late afternoon, and night of August 28, 2019, for one midsized wildfire. Analysis of several metrics showed that the aerosol composition and optical properties varied depending on the burning conditions at the fire zone and the time of day the BBA was emitted, with substantial variations in the available sunlight. The total aerosol mass loadings were dominated by organic components with a much smaller contribution from inorganic species. A gradual buildup of organic material was observed during the afternoon as the plume aged, indicating the condensation of photochemically formed low-volatility oxidized organic compounds. Highly hygroscopic ammonium nitrate was the main inorganic component, suggesting potential water content in BBA particles and the likelihood of their aqueous-phase reactivity. Depletions of particle-phase NO 3 – and Cl – relative to carbon monoxide were observed in the late afternoon and nighttime plumes, respectively, aligning with known gas-particle partitioning thermodynamics and the heterogeneous chemistry of dissolved nitrate and chloride. The wavelength-dependent light absorption by aerosol species was higher for the plume sampled at night and showed no significant changes with plume age, despite observed trends in composition and mass downwind. These differences in particle composition and optical properties demonstrate that the processes involved in BBA aging are not uniform for the same wildfire over the course of the day and depend highly on when the BBA was emitted, as well as the burning phase at the emissions source.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells

Back-contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl 2 -treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO 3 by using a combination of angle-resolved XPS and the cadmium-modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO 3 native oxide. The fates of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO 3 alleviates the downward band bending by 40 meV from 470 to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy, which shows losses in internal open circuit voltage (iVoc) from 820 to 795 meV, carrier lifetime from 123 to 45 ns, and PL quantum yield from 2.9 × 10 −5 to 1.2 × 10 −5 . Modeling timeresolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗
DOE OSTI2025

Synthesis, Stability, and Magnetic Properties of Antiperovskite Co 3 PdN

Experimental synthesis and characterization of theoretically predicted compounds are important steps in the materials discovery pipeline. Here, we report on the synthesis of Co 3 PdN, which was recently predicted to be a stable magnetic antiperovskite. The Co 3 PdN thin films were grown by reactive sputtering and were confirmed to form in an antiperovskite crystal structure. The thermal stability of the compound is demonstrated up to 600 K by in situ X-ray diffraction, though the phase persists at slightly higher temperatures (700 K) in an air-free magnetometer. Both ab initio calculations and magnetization measurements find Co 3 PdN to be ferromagnetic with an experimentally determined Curie temperature of T C = 560 ± 5 K. The saturation magnetization of 1.2 μ B /Co found in the experiment is slightly lower than the 1.7 μ B /Co value expected by theory. A narrow magnetic hysteresis loop with a coercive field of 100 Oe at low temperature suggests that Co 3 PdN might be useful in electronic applications requiring fast switching of the magnetization vector. While prior prediction of Co 3 PdN showed a gapped electronic band structure for each spin channel, we show that this was due to incomplete sampling of Brillouin zone paths and that band crossings exist along R-X|M and X|M-R paths. The metallic nature of Co 3 PdN is further confirmed by temperature-dependent transport measurements, which also show a considerable anomalous Hall effect. Altogether, this work represents an appreciable step toward understanding the synthesis, structure, stability, and properties of a new magnetic material.

14 SOLAR ENERGY↗