Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOUNDARY LAYER - WING SECTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗
NASA NTRS1983

An experimental study of surface curvature effects on a supersonic turbulent boundary layer

The mean flow results of an experimental study of compressible turbulent boundary layers in an adverse pressure gradient with and without surface curvature effects are presented. The test was conducted in an axisymmetric flow facility. The upstream Reynolds number based on boundary layer momentum thickness was 5884 and the boundary layer thickness was 0.90 cm. The curvature effects were examined by studying two flows with essentially identical adverse pressure gradients. One flow was along a concave compression surface test section, while the other was along a straight-walled test section. Mean flow measurements included wall static pressure distributions, wall temperatures, pitot pressure profiles and total temperature profiles. The mean flow results indicated that the surface curvature resulted in a definite increase of turbulent mixing in the boundary layer.

Chou, J. H.↗
NASA NTRS1981

Measurements of the boundary layer and near wake of a supercritical airfoil at cruise conditions

The flow behavior within the upper-surface boundary layer and near wake of a supercritical airfoil operating at cruise conditions is discussed. Experimental results obtained from wind-tunnel tests are presented which provide a more detailed description of the flow in these regions than was previously available. Mean streamwise velocity profiles measured by pitot-pressure-probe and laser-velocimeter techniques were found to be in excellent agreement. Other mean-flow properties obtained by the laser-velocimeter technique were the local flow angles in the viscous layers and the static pressures at the edges of the boundary layer and wake. The data set also includes measurements of the turbulence intensity and turbulent Reynolds-stress distributions as obtained by the laser-velocimeter technique. To assess the effects of the shock wave, a less extensive set of measurements was realized at a subcritical test condition. The two test conditions (Mach number at free-stream conditions = 0.72, airfoil section lift coefficient = 0.76 and Mach number of free-stream conditions = 0.5, airfoil section lift coefficient = 0.75) provide a good test for state-of-the-art prediction methods because the upper-surface-boundary layer is separated just upstream of the trailing edge in both cases.

Johnson, D. A.↗
NASA NTRS1981

Computation of airfoil buffet boundaries

The ILLIAC IV computer has been programmed with an implicit, finite-difference code for solving the thin layer compressible Navier-Stokes equation. Results presented for the case of the buffet boundaries of a conventional and a supercritical airfoil section at high Reynolds numbers are found to be in agreement with experimentally determined buffet boundaries, especially at the higher freestream Mach numbers and lower lift coefficients where the onset of unsteady flows is associated with shock wave-induced boundary layer separation.

Levy, L. L., Jr.↗
NASA NTRS1990

Numerical investigations in three-dimensional internal flows

The flow in the transonic test facility was investigated using the three dimensional computational fluid dynamics techniques. The application of the full Navier-Stokes three dimensional code to the flow qualities in the contraction section of transonic wind tunnel is discussed. Initially, two dimensional solutions indicated the possibility for large secondary flow to exist as a result of the asymmetries involved in the contraction section as it is constructed. The results of a full three dimensional solution indicate that only minor pressure variations actually occur in the contraction section within any given cross flow plane. Further analysis of the three dimensional solution indicated that these slight lateral pressure gradients lead to negligible secondary flows, except within a small region in the corners within the boundary layer. On the basis of present solution, it would not be expected that any flow asymmetries and/or secondary flow present within contraction section are associated with the methods by which the contraction is implemented in its present configuration.

Rose, William C.↗
NASA NTRS1975

Experimental results for the transpired turbulent boundary layer in an adverse pressure gradient

The fluid mechanics of transpired incompressible turbulent boundary layers under zero and adverse pressure gradient conditions is investigated using an open-ended wind tunnel with a porous floor in the test section and a secondary air system for supply and metering of the transpiration air. All velocity profiles and turbulence profiles are obtained by linearized constant-temperature hot-wire anemometry. The wall shear stress is determined by measuring the shear stress away from the wall and extrapolating to the wall by integrating the boundary layer equations for the shear-stress profile. Equilibrium boundary layers are obtained when the transpiration velocity is varied such that the blowing parameter and the Clauser pressure gradient parameter are held constant. The experimental results obtained are presented in tabular and graphical forms.

Andersen, P. S.↗
NASA NTRS2009

Experimental Study of the Effects of Periodic Unsteady Wakes on Flow Separation in Low Pressure Turbines

The present study, which is the first of a series of investigations of low pressure turbine (LPT) boundary layer aerodynamics, is aimed at providing detailed unsteady boundary layer flow information to understand the underlying physics of the inception, onset, and extent of the separation zone. A detailed experimental study on the behavior of the separation zone on the suction surface of a highly loaded LPT-blade under periodic unsteady wake flow is presented. Experimental investigations were performed on a large-scale, high-subsonic unsteady turbine cascade research facility with an integrated wake generator and test section unit. Blade Pak B geometry was used in the cascade. The wakes were generated by continuously moving cylindrical bars device. Boundary layer investigations were performed using hot wire anemometry at Reynolds number of 110,000, based on the blade suction surface length and the exit velocity, for one steady and two unsteady inlet flow conditions, with the corresponding passing frequencies, wake velocities, and turbulence intensities. The reduced frequencies cover the entire operation range of LP-turbines. In addition to the unsteady boundary layer measurements, blade surface pressure measurements were performed at Re = 50,000, 75,000, 100,000, 110,000, and 125,000. For each Reynolds number, surface pressure measurements are carried out at one steady and two periodic unsteady inlet flow conditions. Detailed unsteady boundary layer measurement identifies the onset and extension of the separation zone as well as its behavior under unsteady wake flow. The results, presented in ensemble-averaged and contour plot forms, help to understand the physics of the separation phenomenon under periodic unsteady wake flow.

Ozturk, Burak↗
NASA NTRS1997

Turbulence Modeling Validation, Testing, and Development

The primary objective of this work is to provide accurate numerical solutions for selected flow fields and to compare and evaluate the performance of selected turbulence models with experimental results. Four popular turbulence models have been tested and validated against experimental data often turbulent flows. The models are: (1) the two-equation k-epsilon model of Wilcox, (2) the two-equation k-epsilon model of Launder and Sharma, (3) the two-equation k-omega/k-epsilon SST model of Menter, and (4) the one-equation model of Spalart and Allmaras. The flows investigated are five free shear flows consisting of a mixing layer, a round jet, a plane jet, a plane wake, and a compressible mixing layer; and five boundary layer flows consisting of an incompressible flat plate, a Mach 5 adiabatic flat plate, a separated boundary layer, an axisymmetric shock-wave/boundary layer interaction, and an RAE 2822 transonic airfoil. The experimental data for these flows are well established and have been extensively used in model developments. The results are shown in the following four sections: Part A describes the equations of motion and boundary conditions; Part B describes the model equations, constants, parameters, boundary conditions, and numerical implementation; and Parts C and D describe the experimental data and the performance of the models in the free-shear flows and the boundary layer flows, respectively.

Bardina, J. E.↗
NASA NTRS2004

Free-Stream Turbulence Intensity in the Langley 14- by 22-Foot Subsonic Tunnel

An investigation was conducted using hot-wire anemometry to determine the turbulence intensity levels in the test section of the Langley 14- by 22-Foot Subsonic Tunnel in the closed or walls-down configuration. This study was one component of the three-dimensional High-Lift Flow Physics experiment designed to provide code validation data. Turbulence intensities were measured during two stages of the study. In the first stage, the free-stream turbulence levels were measured before and after a change was made to the floor suction surface of the wind tunnel s boundary layer removal system. The results indicated that the new suction surface at the entrance to the test section had little impact on the turbulence intensities. The second stage was an overall flow quality survey of the empty tunnel including measurements of the turbulence levels at several vertical and streamwise locations. Results indicated that the turbulence intensity is a function of tunnel dynamic pressure and the location in the test section. The general shape of the frequency spectrum is fairly consistent throughout the wind tunnel, changing mostly in amplitude (also slightly with frequency) with change in condition and location.

Neuhart, Dan H.↗
NASA NTRS1972

A procedure for predicting internal and external noise fields of blowdown wind tunnels

The noise generated during the operation of large blowdown wind tunnels is considered. Noise calculation procedures are given to predict the test-section overall and spectrum level noise caused by both the tunnel burner and turbulent boundary layer. External tunnel noise levels due to the tunnel burner and circular jet exhaust flow are also calculated along with their respective cut-off frequency and spectrum peaks. The predicted values are compared with measured data, and the ability of the prediction procedure to estimate blowdown-wind-tunnel noise levels is shown.

Hosier, R. N.↗
NASA NTRS1985

Numerical study of three-dimensional turbulent flow interactions between blockage models and wind tunnels including longitudinally slotted test sections

A spatial forward-marching approach is applied to compute three-dimensional turbulent flows for several blockage models in free flight, in a solid wall wind tunnel, and in a wind tunnel with longitudinal slots in the test section. The effects of area blockage in the tunnel, model growth and tunnel wall boundary layers, and of the slots are included. The large blockage models are found to have significant wall interference effects which can be reduced by the slots. The effects of the latter are confined to the region near the tunnel wall. Model/wall interference effects are not limited to the effects of area blockage; in particular, boundary layer profile shapes for a wind tunnel model in a tunnel are different from shapes for a model in free flight even when slots are used. This indicates that the flow responds differently in these two cases with the same pressure gradient.

Lin, S.-J.↗
NASA NTRS2007

Wall Boundary Layer Measurements for the NASA Langley Transonic Dynamics Tunnel

Measurements of the boundary layer parameters in the NASA Langley Transonic Dynamics tunnel were conducted during extensive calibration activities following the facility conversion from a Freon-12 heavy-gas test medium to R-134a. Boundary-layer rakes were mounted on the wind-tunnel walls, ceiling, and floor. Measurements were made over the range of tunnel operation envelope in both heavy gas and air and without a model in the test section at three tunnel stations. Configuration variables included open and closed east sidewall wall slots, for air and R134a test media, reentry flap settings, and stagnation pressures over the full range of tunnel operation. The boundary layer thickness varied considerably for the six rakes. The thickness for the east wall was considerably larger that the other rakes and was also larger than previously reported. There generally was some reduction in thickness at supersonic Mach numbers, but the effect of stagnation pressure, and test medium were not extensive.

Wieseman, Carol D.↗
NASA NTRS2021

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗
NASA NTRS2022

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗
NASA NTRS1998

The detection of clouds, aerosols and marine atmospheric boundary layer characteristics from simulated GLAS data

Scheduled for launch in 2001 as part of NASA's Earth Observing System (EOS), the Geoscience Laser Altimeter System (GLAS) will provide continuous laser sounding of the earth's atmosphere from space for the first time. From its polar orbit about 600 km above the surface, GLAS will employ a 40 Hz solid state laser operating at 1064 nm to measure topography to an accuracy of 10 cm. Simultaneously, the atmospheric channels (1064 and 532 nm) of GLAS will provide profiles of atmospheric backscatter from 40 km to the ground with 75 meter vertical resolution (Spinhirne and Palm, 1996). These measurements will give scientists an unprecedented global data set on the vertical structure of clouds and aerosols which will greatly aid research efforts aimed at understanding their effects on climate and their role in climate change (Hartman, 1994). To better understand and predict the performance of the GLAS atmospheric channels, a computer model was developed to simulate the type of signal that the instrument would likely produce. The model uses aircraft lidar data and provides realistic simulated GLAS data sets over large areas spanning a wide range of atmospheric conditions. These simulated GLAS datasets are invaluable for designing and testing algorithms for the retrieval of parameters such as cloud and aerosol layer height, optical depth and extinction cross section. This work is currently proceeding and in this paper we will present results of the cloud and aerosol detection algorithm with emphasis on the detection of Marine Atmospheric Boundary Layer (MABL) aerosol. In addition, we use a recently developed technique to ascertain the feasability of estimating MABL moisture and temperature structure from spaceborne systems such as GLAS.

Palm, Stephen P.↗
NASA NTRS1984

Natural laminar flow airfoil design considerations for winglets on low-speed airplanes

Winglet airfoil section characteristics which significantly influence cruise performance and handling qualities of an airplane are discussed. A good winglet design requires an airfoil section with a low cruise drag coefficient, a high maximum lift coefficient, and a gradual and steady movement of the boundary layer transition location with angle of attack. The first design requirement provides a low crossover lift coefficient of airplane drag polars with winglets off and on. The other requirements prevent nonlinear changes in airplane lateral/directional stability and control characteristics. These requirements are considered in the design of a natural laminar flow airfoil section for winglet applications and chord Reynolds number of 1 to 4 million.

Vandam, C. P.↗
NASA NTRS1997

Atmospheric Layers Measured from the NASA DC-8 During PEM-West B and Comparison with PEM-West A

The Pacific Exploratory Mission-West B (PEM-West B) explored atmospheric layer structure using measurements of O3, H2O, CO, and CH4 from the NASA DC-8 fast-response instruments. The mission took place in February-March 1994 over the western Pacific, mainly in the northern hemisphere. Results were compared with similar measurements made during the Pacific Exploratory Mission-West A (PEM-West A) in September-October 1991. PEM-West B sampled 94 vertical profiles, with an average atmospheric depth per profile of 6.4 km, and this sampling yielded 254 discrete layers. PEM-West A sampled 105 profiles, also with a 6.4 km average depth, yielding 538 layers. Both missions revealed that layers containing high ozone and low water vapor were the most abundant, and low ozone and high water vapor layers were the next most abundant. Lidar images and potential vorticity cross sections showed the former associated with subsidence from the stratosphere in middle latitudes, spreading into the tropics. The latter was associated with convection from the boundary layer. The partition among different types of layers only changed slightly in the two missions, although PEM-West B had half as many layers. Compared to PEM-West A, PEM-West B showed only one-third the number of layers associated with polluted continental air. However, PEM-West B revealed significantly more layers showing characteristics of descended clean marine air. In some cases these layers originated from the southern hemisphere. For ozone- and water-vapor-rich layers, the ozone deviation amplitude was higher in low latitudes and lower in high latitudes in PEM-West B. The mean thickness of layers increased from about 450 m in PEM-West A to 680 in in PEM-West B. Layers also existed in the Intertropical Convergence Zone. CO2 measurements had sufficient vertical resolution to show layer structure as well.

Wu, Zhongxiang↗
NASA NTRS1975

Data correlation and analysis of arc tunnel and wind tunnel tests of RSI joints and gaps, phase 2. Volume 1: Technical report

Heat transfer data measured in gaps representative of those being employed for joints in the space shuttle reusable surface insulation (RSI) thermal protection systems (TPS) were assimilated, analyzed, and correlated. Several types of gap were investigated with emphasis on simple butt joints. Gap widths ranged from 0.0 to 0.76 cm and depths ranged from 1 to 6 cm. Laminar, transitional, and turbulent boundary layer flows over the gap opening were investigated. The angle between gap axis and external flow was varied between 0 and pi/2 radians. The contoured cross section gap performed significantly better than all other wide gaps and slightly better than all other narrow gap geometries. Three dimensional heating variations were observed within gaps in the absence of external flow pressure gradients. Interactions between heating within gaps and heating of adjacent top tile surfaces were observed. Gaps aligned with the flow were observed to promote boundary layer transition. Heat transfer correlation equations were obtained for many of the tests. The TPS thickness requirements with and without gaps were computed for a current shuttle entry trajectory. Experimental data employed in the study are summarized. A description of each test facility, run schedule and test conditions, model descriptive information, and heat flux data are included.

Cristensen, H. E.↗