Search NASA⌕ Search

SEARCH · Search NASA

Results for “Beam sensitive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

System overview on electromagnetic compensation for reflector antenna surface distortion

The system requirements and hardware implementation for electromagnetic compensation of antenna performance degradations due to thermal effects was investigated. Future commercial space communication antenna systems will utilize the 20/30 GHz frequency spectrum and support very narrow multiple beams (0.3 deg) over wide angle field of view (15-20 beamwidth). On the ground, portable and inexpensive very small aperture terminals (VSAT) for transmitting and receiving video, facsimile and data will be employed. These types of communication system puts a very stringent requirement on spacecraft antenna beam pointing stability (less than .01 deg), high gain (greater than 50 dB) and very lowside lobes (less than -25 dB). Thermal analysis performed on the advanced communication technology satellite (ACTS) has shown that the reflector surfaces, the mechanical supporting structures and metallic surfaces on the spacecraft body will distort due thermal effects from a varying solar flux. The antenna performance characteristics (e.g., pointing stability, gain, side lobe, etc.) will degrade due to thermal distortion in the reflector surface and supporting structures. Specifically, antenna RF radiation analysis has shown that pointing error is the most sensitive antenna performance parameter to thermal distortions. Other antenna parameters like peak gain, cross polarization level (beam isolation), and side lobe level will also degrade with thermal distortions. In order to restore pointing stability and in general antenna performance several compensation methods were proposed. In general these compensation methods can be classified as being either of mechanical or electromagnetic type. This paper will address only the later one. In this approach an adaptive phased array antenna feed is used to compensate for the antenna performance degradation. Extensive work has been devoted to demonstrate the feasibility of adaptive feed compensation on space communication antenna systems. This paper addresses the system requirements for such a system and identify candidate technologies (analog and digital) for possible hardware implementation.

Acosta, R. J.↗
NASA NTRS1998

Ladder-structured photonic variable delay device

An ladder-structured variable delay device for providing variable true time delay to multiple optical beams simultaneously. The device comprises multiple basic units stacked on top of each other resembling a ladder. Each basic unit comprises a polarization sensitive corner reflector formed by two polarization beamsplitters and a polarization rotator array placed parallel to the hypotenuse of the corner reflector. Controlling an array element of the polarization rotator array causes an optical beam passing through the array element to either go up to a basic unit above it or reflect back towards output. The beams going higher on the ladder experience longer optical path delay. Finally, the ladder-structured variable device can be cascaded with another multi-channel delay device to form a new device which combines the advantages of the two individual devices. This programmable optic device has the properties of high packing density, low loss, easy fabrication, and virtually infinite bandwidth. In addition, the delay is reversible so that the same delay device can be used for both antenna transmitting and receiving.

Yao, X. Steve↗
NASA NTRS2003

Interferometer for Measuring Displacement to Within 20 pm

An optical heterodyne interferometer that can be used to measure linear displacements with an error <=20 pm has been developed. The remarkable accuracy of this interferometer is achieved through a design that includes (1) a wavefront split that reduces (relative to amplitude splits used in other interferometers) self interference and (2) a common-optical-path configuration that affords common-mode cancellation of the interference effects of thermal-expansion changes in optical-path lengths. The most popular method of displacement- measuring interferometry involves two beams, the polarizations of which are meant to be kept orthogonal upstream of the final interference location, where the difference between the phases of the two beams is measured. Polarization leakages (deviations from the desired perfect orthogonality) contaminate the phase measurement with periodic nonlinear errors. In commercial interferometers, these phase-measurement errors result in displacement errors in the approximate range of 1 to 10 nm. Moreover, because prior interferometers lack compensation for thermal-expansion changes in optical-path lengths, they are subject to additional displacement errors characterized by a temperature sensitivity of about 100 nm/K. Because the present interferometer does not utilize polarization in the separation and combination of the two interfering beams and because of the common-mode cancellation of thermal-expansion effects, the periodic nonlinear errors and the sensitivity to temperature changes are much smaller than in other interferometers

Zhao, Feng↗
NASA NTRS1994

Infrared astronomy from the Moon

The purpose of this paper is to exhibit the advantages and limitations to infrared astronomical observations form the moon. The most obvious apparent advantage is the lack of a lunar atmosphere; radiation arriving from the universe is neither extinguished nor refracted as it approaches the lunar surface. However, the Earth's atmosphere's protection against cosmic rays is also lost, and infrared detectors are highly sensitive to irradiation by energetic particles. A second apparent advantage is the relative ease with which beams from an array of telescopes can be interferometrically combined; again the vacuum environment with constant refractive index of unity throughout, permits combination without phase delay across the entire spectral range. But thermal radiation from optical components and stray radiation from the lunar environment, just outside the light path, tend to lessen that advantage, except in narrow-spectral-band spatial interferometry, in which only the radiation in individual spectral lines is mapped, and broad-band thermal emission can be effectively filtered out. On the Moon's night side, and in polar craters on the Moon, radiative cooling should permit the attainment of high sensitivity with large telescopes. Just as the proposed Edison spacecraft primary mirror is expected to reach temperatures around 40 K, so also large lunar primary mirrors might be expected to reach temperatures in that range, making the zodiacal glow the main source of noise at wavelengths shortward of 25 micrometers. The slow rota tion of the Moon, and the lack of vibrations from natural sources such as winds, should provide advantages in guiding on specific astronomical sources. To learn as much as possible about the difficulties of remote observations in a hostile environment, Antarctic observatories should be used as test beds for the rigors of lunar observations. The strenuous requirements for successful astronomical observations from the South Pole are similar to those expected to be encountered in observations conducted from the Moon.

Harwit, Martin↗
NASA NTRS1982

Integration and compaction of optical systems in the mid-infrared

Problems in the design of optical systems for use with mid-IR (MIR; 10.6-micron) lasers are reviewed. The cryogenically operated lead-chalcogenide tunable diode lasers currently used as sources emit complex far-field patterns and require sophisticated beam collection, shaping, and guide optics. Since conventional optics using large mirrors and Ge lenses are often awkward to use and sensitive to vibration, and since optical fibers for the MIR have not been perfected, current research concentrates on hollow flexible rectangular metallic pipes. These pipes are shown to provide transmission of 95 percent or better over a 1-m length, with beam shaping and polarization control. The low transmission losses and wideband IR transmission of single-crystal alkali halides suggest the feasibility of their use in MIR optical fibers and waveguides.

Yu, C.↗
NASA NTRS1986

Sensitivity of the Lidar ratio to changes in size distribution and index of refraction

In order to invert lidar signals to obtain reliable extinction coefficients, sigma, a relationship between sigma and the backscatter coefficient, beta, must be given. These two coefficients are linearly related if the complex index of refraction, m, particle shape size distribution, N, does not change along the path illuminated by the laser beam. This, however, is generally not the case. An extensive Mie computation of the lidar ratio R = beta/sigma and the sensitivity of R to the changes in a parametric space defined by N and m were examined.

Evans, B. T. N.↗
NASA NTRS1992

Radiation sensitivity of quartz crystal oscillators experiment for the Long Duration Exposure Facility (LDEF)

Factors determining the radiation sensitivity of quartz crystal oscillators were studied on NASA's LDEF. Quartz materials were examined in the transmission electron microscope (TEM) and classified as to their sensitivity to radiation damage by establishing the rate of damage caused by the electron beam in the microscope. Two types of materials, i.e., swept premium Q quartz and natural quartz were chosen because clear differences were observed in their response to the electron beam in the TEM studies. Quartz resonators were then fabricated from them, tested for frequency stability over a greater than 6 mo. period and flown on the LDEF satellite. After retrieval (more than 7 yrs in space) the stability of the resonators was again determined. All of the space exposed resonators fabricated with swept premium Q material exhibited a frequency shift above that of the control resonators: none of the resonators fabricated from the natural quartz materials exhibited such a shift. The significant differences observed between the two types of materials in both the ground-based TEM studies and the space radiation induced frequency changes suggest that there may be a correlation between the two observations.

Ahearn, J. S.↗
NASA NTRS1993

The HYDICE instrument design and its application to planetary instruments

The Hyperspectral Digital Imagery Collection Experiment (HYDICE) instrument represents a significant advance in the state of the art in hyperspectral sensors. It combines a higher signal-to-noise ratio (SNR) and significantly better spatial and spectral resolution and radio metric accuracy than systems flying on aircraft today. The need for 'clean' data, i.e., data free of sampling artifacts and excessive spatial or spectral noise, is a key driver behind the difficult combination of performance requirements laid out for HYDICE. Most of these involve the sensor optics and detector. This paper presents an optimized approach to those requirements, one that comprises push broom scanning, a single, mechanically cooled focal plane, a double-pass prism spectrometer, and an easily fabricated yet wide-field telescope. Central to the approach is a detector array that covers the entire spectrum from 0.4 to 2.5 microns. Among the major benefits conferred by such a design are optical and mechanical simplicity, low polarization sensitivity, and coverage of the entire spectrum without suffering the spectral gaps caused by beam splitters. The overall system minimizes interfaces to the C-141 aircraft on which it will be flown, can be calibrated on the ground and in flight to accuracies better than those required, and is designed for simple, push-button operation. Only unprocessed data are recorded during flight. A ground data processing station provides quick-look, calibration correction, and archiving capabilities, with a throughput better than the requirements. Overall performance of the system is expected to provide the solid database required to evaluate the potential of hyperspectral imagery in a wide variety of applications. HYDICE can be regarded as a test bed for future planetary instruments. The ability to spectrally image a wide field of view over multiple spectral octaves offers obvious advantages and is expected to maximize science return for the required cost and weight.

Basedow, R.↗
NASA NTRS2020

Comparison of Extreme Value Distributions for Electrostatic Discharge Magnitudes in Spacecraft Charging Tests

Electrostatic Discharge (ESD) induced by the accumulation of charge in the space environment is known to cause spacecraft anomalies and failures. While it is critical to estimate the worst-case expected ESD, sensitive radar instruments can be impacted by high rates of occurrence of very small ESD. To estimate the correct extreme behavior, it is important to select the correct extreme value distribution for extrapolation of test results limited in time and sensitivity. Quantile-quantile (Q-Q) analysis is used to compare electron beam-induced ESD test data to several statistical distributions used in the published literature. The best-fit distribution is shown to vary from between tests on different materials; however, it is clear that power law distributions are not good approximations for low amplitude events. Q-Q analysis is a convenient graphical method for evaluating multiple theoretical extreme-value distributions simultaneously.

Kim, Wousik↗
NASA NTRS1981

Performance of a magnetic multipole line-cusp argon ion thruster

A 17 cm diameter line cusp ion thruster was evaluated with inert gases which are candidate propellants for on orbit and orbit transfer propulsion functions for Large Space Systems. A semiempirical relationship was generated to predict thruster beam current in terms of plasma parameters which would allow initial thruster optimization without ion extraction and the associated large vacuum facilities. The sensitivity of performance to changes in discharge electrode configurations and magnetic circuit was evaluated and is presented. After final optimization a propellant utilization efficiency of 0.9 at a discharge chamber power expenditure of about 260 w per beam ampere was obtained. These performance parameters are the highest yet achieved with argon propellant.

Sovey, J. S.↗
NASA NTRS1989

Accurate calculation of control-augmented structural eigenvalue sensitivities using reduced-order models

A method is presented for generating mode shapes for model order reduction in a way that leads to accurate calculation of eigenvalue derivatives and eigenvalues for a class of control augmented structures. The method is based on treating degrees of freedom where control forces act or masses are changed in a manner analogous to that used for boundary degrees of freedom in component mode synthesis. It is especially suited for structures controlled by a small number of actuators and/or tuned by a small number of concentrated masses whose positions are predetermined. A control augmented multispan beam with closely spaced natural frequencies is used for numerical experimentation. A comparison with reduced-order eigenvalue sensitivity calculations based on the normal modes of the structure shows that the method presented produces significant improvements in accuracy.

Livne, Eli↗
NASA NTRS2015

Advanced Solar Electric Propulsion for Planetary Defense

Once the current survey to identify all near-Earth objects larger than 140-m diameter is complete, the major hazard from asteroid impacts may be from asteroids in the 50- to 100-m diameter size range. High-power solar electric propulsion systems employed in “slow-push” techniques may be the best way to deflect asteroids in this size range if deflection is warranted. The relative performance of three slow-push techniques—gravity tractor (GT), enhanced gravity tractor (EGT), and ion beam deflection (IBD)—are compared, assuming solar electric propulsion vehicles derived from NASA’s Asteroid Redirect Robotic Mission concept vehicle. Both the enhanced gravity tractor and ion beam deflection concepts are shown to be significantly better than the standard gravity tractor concept. The Hall-thruster based enhanced gravity tractor systems and ion beam deflection systems (based on the use of high-power gridded ion thrusters) are shown to provide comparable performance, i.e., similar deflection times and propellant required. Enhanced gravity tractor systems require the acquisition of material from the surface of the hazardous object in order to achieve the required “enhancement” of the gravitational coupling force. This makes EGT systems sensitive to the rotational state and surface properties of the unknown object, and potentially severely limits its applicability. Ion beam deflection is completely independent of the characteristics of the threat object. In fact, it is the only asteroid deflection technique, slow-push or otherwise, that can make this claim, thus potentially greatly increasing its applicability relative to other deflection techniques. Finally, high-power IBD systems are shown to be capable of deflecting the fictitious asteroid 2015 PDC used in the hypothetical asteroid impact exercise conducted at the 2015 Planetary Defense Conference.

Brophy, John↗
NASA NTRS1991

Distributed parameter estimation for NASA Mini-Mast truss through displacement measurements

Most methods of system identification of large flexible structures by far are based on the lumped parameter approach. Because of the considerable computational burden due to the large number of unknown parameters, distributed parameter approach, which greatly decreases the number of unknowns, has being investigated. In this paper a distributed parameter model for the estimation of modal characteristics of NASA Mini-Mast truss has been formulated. Both Bernoulli-Euler beam and Timoshenko beam equations are used to characterize the lateral bending vibrations of the truss. The measurement of the lateral displacement at the tip of the truss is provided to the maximum likelihood estimator. Closed-form solutions of the partial differential equations and closed-form expressions of the sensitivity functions are derived so that the estimation algorithm is highly efficient. The resulting estimates from test data by using Timoshenko beam model are found to be comparable to those derived from finite element analysis.

Huang, Jen-Kuang↗
NASA NTRS1981

Direction sensitive laser velocimeter

A laser velocimeter is described which determines the direction of movement of particles. A laser produces a transmitted beam that illuminates the volume under investigation. The backscattered light is divided into two equal intensity beams. A first part of a sample of the transmitted beam is mixed with one of the two equal intensity beams and applied to a first photodetector. A second part of the sample is phase shifted by 90 deg, mixed with the other of the two equal intensity beams and applied to a second photodetector. The output of the first photodetector is phase shifted by 90 deg and then multiplied with the output of the second photodetector to produce a signal indicative of direction of movement.

Franke, J. M.↗
NASA NTRS2013

Simulated Beam Extraction Performance Characterization of a 50-cm Ion Thruster Discharge

A 50 cm ion thruster is being developed to operate at >65 percent total efficiency at 11 kW, 2700 s Isp and over 25 kW, 4500 s Isp at a total efficiency of >75 percent. The engine is being developed to address the need for a multimode system that can provide a range of thrust-to- power to service national and commercial near-earth onboard propulsion needs such as station-keeping and orbit transfer. Operating characteristics of the 50 cm ion thruster were measured under simulated beam extraction. The discharge current distribution at the various magnet rings was measured over a range of operating conditions. The relationship between the anode current distribution and the resulting plasma uniformity and ion flux measured at the thruster exit plane is discussed. The thermal envelope will also be investigated through the monitoring of magnet temperatures over the range of discharge powers investigated. Discharge losses as a function of propellant utilization was also characterized at multiple simulated beam currents. Bulk plasma conditions such as electron temperature and electron density near engine centerline was measured over a range of operating conditions using an internal Langmuir probe. Sensitivity of discharge performance to chamber length is also discussed. This data acquired from this discharge study will be used in the refinement of a throttle table in anticipation for eventual beam extraction testing.

Foster, John E.↗
NASA NTRS2012

Development of a Robust, High Current, Low Power Field Emission Electron Gun for a Spaceflight Reflectron Time-of-Flight Mass Spectrometer

Carbon materials, including carbon nanotubes (CNTs) and nitrogen-incorporated ultrananocrystalline diamond (N-UNCD), have been of considerable interest for field emission applications for over a decade. In particular, robust field emission materials are compelling for space applications due to the low power consumption and potential for miniaturization. A reflectron time-of-flight mass spectrometer (TOF-MS) under development for in situ measurements on the Moon and other Solar System bodies uses a field emitter to generate ions from gaseous samples, using electron ionization. For these unusual environments, robustness, reliability, and long life are of paramount importance, and to this end, we have explored the field emission properties and lifetime of carbon nanotubes and nitrogen-incorporated ultrananocrystalline diamond (N-UNCD) thin films, the latter developed and patented by Argonne National Laboratory. We will present recent investigations of N-UNCD as a robust field emitter, revealing that this material offers stable performance in high vacuum for up to 1000 hours with threshold voltage for emission of about 3-4 V/lJm and current densities in the range of tens of microA. Optimizing the mass resolution and sensitivity of such a mass spectrometer has also been enabled by a parallel effort to scale up a CNT emitter to an array measuring 2 mm x 40 mm. Through simulation and experiment of the new extended format emitter, we have determined that focusing the electron beam is limited due to the angular spread of the emitted electrons. This dispersion effect can be reduced through modification of the electron gun geometry, but this reduces the current reaching the ionization region. By increasing the transmission efficiency of the electron beam to the anode, we have increased the anode current by two orders of magnitude to realize a corresponding enhancement in instrument sensitivity, at a moderate cost to mass resolution. We will report recent experimental and modeling results to describe the performance of a field emission electron gun as employed in the Volatile Analysis by Pyrolysis of Regolith (VAPoR) TOF-MS prototype.

Southard, Adrian E.↗
NASA NTRS1974

Holographic recording materials development

Developments in the area of organic cis-trans isomerization systems for holographic memory applications are reported. The chemical research effort consisted of photochemical studies leading to the selection of a stilbene derivative and a polymer matrix system which have greatly improved refractive index differences between the cis and trans isomers as well as demonstrated efficiency of the photoisomerization process. In work on lithium niobate effects of sample stoichiometry and of read and write beam polarizations on recording efficiency were investigated. LiNbO3 was used for a study of angular sensitivity and of capability for simultaneous recording of extended objects without interference. The current status of LiNbO3 as a holographic recording material is summarized.

Source record↗
NASA NTRS1974

A lidar system for remote probing of the lower atmosphere

The development and characteristics of a lidar system for atmospheric measurements are discussed. The lidar system employs a Q-switched ruby laser that radiates an intense pulse of light into the atmosphere to illuminate aerosol particles in the laser beam. Light backscattered from the particles is received by a Cassegrain telescope equipped with a sensitive photomultiplier tube. The output signal of the photomultiplier tube is displayed on an oscilloscope and recorded on polaroid film.

Craig, C. D.↗