Search NASA⌕ Search

SEARCH · Search NASA

Results for “CIRCULAR CONFIGURATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Transmission of sound through nonuniform circular ducts with compressible mean flows

An acoustic theory is developed to determine the sound transmission and attenuation through an infinite, hard-walled or lined, circular duct carrying compressible, sheared, mean flows and having a variable cross section. The theory is applicable to large as well as small axial variations, as long as the mean flow does not separate. Although the theory is described for circular ducts, it is applicable to other duct configurations - annular, two dimensional, and rectangular. The theory is described for the linear problem, but the technique is general and has the advantage of being applicable to the nonlinear case as well as the linear case. The technique is based on solving for the envelopes of the quasi-parallel acoustic modes that exist in the duct instead of solving for the actual wave. A computer program was developed. The mean flow model consists of a one dimensional flow in the core and a quarter-sine profile in the boundary layer. Results are presented for the reflection and transmission coefficients in ducts with varying slopes and carrying different mean flows.

Nayfeh, A. H.↗

Computer analysis of flow perturbations generated by placement of choke bumps in a wind tunnel

An inviscid analytical study was conducted to determine the upstream flow perturbations caused by placing choke bumps in a wind tunnel. A computer program based on the stream-tube curvature method was used to calculate the resulting flow fields for a nominal free-stream Mach number range of 0.6 to 0.9. The choke bump geometry was also varied to investigate the effect of bump shape on the disturbance produced. Results from the study indicate that a region of significant variation from the free-stream conditions exists upstream of the throat of the tunnel. The extent of the disturbance region was, as a rule, dependent on Mach number and the geometry of the choke bump. In general, the upstream disturbance distance decreased for increasing nominal free-stream Mach number and for decreasing length-to-height ratio of the bump. A polynomial-curve choke bump usually produced less of a disturbance than did a circular-arc bump and going to an axisymmetric configuration (modeling choke bumps on all the tunnel walls) generally resulted in a lower disturbance than with the corresponding two dimensional case.

Campbell, R. L.↗

Annular Electrode Improves Solar-Cell Welds

Improved method of electrical-resistance welding of solar-cell inter-connections developed by using an annular welding-electrode shape. Improved weld electrode consists of two coaxial cylinders, outer one with annular cross section and inner one with circular cross section. Possible annular weld-electrode configurations result in better quality welds for interconnecting solar-array elements.

Baraona, C. R.↗

The 20 GHz circularly polarized, high temperature superconducting microstrip antenna array

The primary goal was to design and characterize a four-element, 20 GHz, circularly polarized microstrip patch antenna fabricated from YBa2Cu3O(x) superconductor. The purpose is to support a high temperature superconductivity flight communications experiment between the space shuttle orbiter and the ACTS satellite. This study is intended to provide information into the design, construction, and feasibility of a circularly polarized superconducting 20 GHz downlink or cross-link antenna. We have demonstrated that significant gain improvements can be realized by using superconducting materials for large corporate fed array antennas. In addition, we have shown that when constructed from superconducting materials, the efficiency, and therefore the gain, of microstrip patches increases if the substrate is not so thick that the dominant loss mechanism for the patch is radiation into the surface waves of the conductor-backed substrate. We have considered two design configurations for a superconducting 20 GHz four-element circularly polarized microstrip antenna array. The first is the Huang array that uses properly oriented and phased linearly polarized microstrip patch elements to realize a circularly polarized pattern. The second is a gap-coupled array of circularly polarized elements. In this study we determined that although the Huang array operates well on low dielectric constant substrates, its performance becomes extremely sensitive to mismatches, interelement coupling, and design imperfections for substrates with high dielectric constants. For the gap-coupled microstrip array, we were able to fabricate and test circularly polarized elements and four-element arrays on LaAlO3 using sputtered copper films. These antennas were found to perform well, with relatively good circular polarization. In addition, we realized a four-element YBa2Cu3O(x) array of the same design and measured its pattern and gain relative to a room temperature copper array. The patterns were essentially the same as that for the copper array. The measured gain of the YBCO antenna was greater than that for the room temperature copper design at temperatures below 82K, reaching a value of 3.4 dB at the lowest temperatures.

Morrow, Jarrett D.↗

Numerical analysis of natural convection in two-dimensional square and circular containers in low gravity

A numerical study of natural convection in circular cylinder and square enclosures shows that the analytic low Rayleigh number theory of previous investigators is valid for Rayleigh numbers up to 1000. For a Rayleigh number of 5000, steady state values of maximum fluid velocity differ by 20 percent. This deviation between analytic theory and numerical results increases for higher Rayleigh numbers. In addition, the low Rayleigh number theory is shown to be valid for higher Rayleigh numbers for a portion of the transient phase before significant deviation becomes apparent. It is also shown that square shaped experimental configurations may be analytically approximated with good accuracy by circular cylinders of equal cross sectional area for the prediction of convection velocities and flow patterns at low Rayleigh number.

Robertson, S. J.↗

THE RADIATIVE TRANSFER OF SYNCHROTRON RADIATION THROUGH A COMPRESSED RANDOM MAGNETIC FIELD

This paper examines the radiative transfer of synchrotron radiation in the presence of a magnetic field configuration resulting from the compression of a highly disordered magnetic field. It is shown that, provided Faraday rotation and circular polarization can be neglected, the radiative transfer equations for synchrotron radiation separate for this configuration, and the intensities and polarization values for sources that are uniform on large scales can be found straightforwardly in the case where opacity is significant. Although the emission and absorption coefficients must, in general, be obtained numerically, the process is much simpler than a full numerical solution to the transfer equations. Some illustrative results are given and an interesting effect, whereby the polarization increases while the magnetic field distribution becomes less strongly confined to the plane of compression, is discussed. The results are of importance for the interpretation of polarization near the edges of lobes in radio galaxies and of bright features in the parsec-scale jets of active galactic nuclei, where such magnetic field configurations are believed to exist.

79 ASTRONOMY AND ASTROPHYSICS↗

Combustion and Emissions Study Using a 7-Point Lean Direct Injector Array

This paper continues a parametric study in which we consider the effect of air swirler configuration on the flame structure and combustor performance using a circular 7-point Lean Direct Injector Array for gas turbine applications. The injector array consists of a center swirler element surrounded by six swirler elements. Parameters considered in this study include swirler angle (60° or 52°), handedness (co-swirling or counter-swirling) and center swirler offset. The primary focus considers flame stability, comparing four key air swirler configurations: for 1) fuel-lean flames; 2) high cold flow air reference velocity flames. We determined that the baseline swirler configuration had the best lean stability and could sustain the highest reference velocity. For this baseline configuration, we also compare the lean-blowout limits of four aircraft gas turbine reference fuels. With regard to lean blow-out, we determined that C4 could sustain the leanest flame, followed closely by A2. A1 was a poor performer.

gas turbine combustors↗

Combustion and Emissions Study Using a 7-Point Lean Direct Injector Array Focus on Flame Stability

This paper continues a parametric study in which we consider the effect of air swirler configuration on the flame structure and combustor performance using a circular 7-point Lean Direct Injector Array for gas turbine applications. The injector array consists of a center swirler element surrounded by six swirler elements. Parameters considered in this study include swirler angle (60° or 52°), handedness (co-swirling or counter-swirling) and center swirler offset. The primary focus considers flame stability, comparing four key air swirler configurations: for 1) fuel-lean flames; 2) high cold flow air reference velocity flames. We determined that the baseline swirler configuration had the best lean stability and could sustain the highest reference velocity. For this baseline configuration, we also compare the lean-blowout limits of four aircraft gas turbine reference fuels. With regard to lean blow-out, we determined that C4 could sustain the leanest flame, followed closely by A2. A1 was a poor performer.

fluid mixing↗

Design of a thermocapillary flow experiment in reduced gravity

Detailed considerations for the design of a low-gravity thermocapillary flow experiment are presented. The basic configuration is one in which a fluid contained in a circular dish is subjected to an imposed surface heat flux. Specific consideration is given to the imposed thermal signature, thermal boundary conditions, free-surface deformations, and g-jitter effects. Numerical analysis and ground-based and drop-tower tests are utilized to ensure that reasonable flows are obtained in which measurements can be made relatively easily. The configuration chosen is of further importance because it differs from others in which oscillations were observed.

Kamotani, Y.↗

Advanced Natural Gas Reciprocating Engine: Parasitic Loss Control through Surface Modification

This report presents results of our investigation on parasitic loss control through surface modification in reciprocating engine. In order to achieve the objectives several experimental and corresponding analytical models were designed and developed to corroborate our results. Four different test rigs were designed and developed to simulate the contact between the piston ring and cylinder liner (PRCL) contact. The Reciprocating Piston Test Rig (RPTR) is a novel suspended liner test apparatus which can be used to accurately measure the friction force and side load at the piston-cylinder interface. A mixed lubrication model for the complete ring-pack and piston skirt was developed to correlate with the experimental measurements. Comparisons between the experimental and analytical results showed good agreement. The results revealed that in the reciprocating engines higher friction occur near TDC and BDC of the stroke due to the extremely low piston speed resulting in boundary lubrication. A Small Engine Dynamometer Test Rig was also designed and developed to enable testing of cylinder liner under motored and fired conditions. Results of this study provide a baseline from which to measure the effect of surface modifications. The Pin on Disk Test Rig (POD) was used in a flat-on-flat configuration to study the friction effect of CNC machining circular pockets and laser micro-dimples. The results show that large and shallow circular pockets resulted in significant friction reduction. Deep circular pockets did not provide much load support. The Reciprocating Liner Test Rig (RLTR) was designed to simplifying the contact at the PRCL interface. Accurate measurement of friction was obtained using 3-axis piezoelectric force transducer. Two fiber optic sensors were used to measure the film thickness precisely. The results show that the friction force is reduced through the use of modified surfaces. The Shear Driven Test Rig (SDTR) was designed to simulate the mechanism of the piston ring pass through the liner. Micro PIV system was provided to observing the flow of lubricant in the cavity (pocket). The Vorticity-Stream Function Code was developed to simulate the incompressible fluid flow in the rectangular cavity.

03 NATURAL GAS↗

Experimental Aeroheating Study of Mid-L/D Entry Vehicle Geometries: NASA LaRC 20-Inch Mach 6 Air Tunnel Test 6966

Aeroheating data on mid lift-to-drag ratio entry vehicle configurations has been obtained through hypersonic wind tunnel testing. Vehicles of this class have been proposed for high-mass Mars missions, such as sample return and crewed exploration, for which the conventional sphere-cone entry vehicle geometries of previous Mars missions are insufficient. Several configurations were investigated, including elliptically-blunted cylinders with both circular and elliptical cross sections, biconic geometries based on launch vehicle dual-use shrouds, and parametrically-optimized analytic geometries. Testing was conducted at Mach 6 over a range of Reynolds numbers sufficient to generate laminar, transitional, and turbulent flow. Global aeroheating data were obtained using phosphor thermography. Both stream-wise and cross-flow transition occured on different configurations. Comparisons were made with laminar and turbulent computational predictions generated with an algebraic turbulence model. Predictions were generally in good agreement in regions of laminar or fully-turbulent flow; however for transitional cases, the lack of a transition onset prediction capability produced less accurate comparisons. The data obtained in this study are intended to be used for prelimary mission design studies and the development and validation of computational methods.

Hollis, Brian R.↗

Selection process for trade study: Graphite Composite Primary Structure (GCPS)

This TA 2 document describes the selection process that will be used to identify the most suitable structural configuration for an SSTO winged vehicle capable of delivering 25,000 lbs to a 220 nm circular orbit at 51.6 degree inclination. The most suitable unpressurized graphite composite structures and material selections is within this configuration and will be the prototype design for subsequent design and analysis and the basis for the design and fabrication of payload bay, wing, and thrust structure full scale test articles representing segments of the prototype structures. The selection process for this TA 2 trade study is the same as that for the TA 1 trade study. As the trade study progresses additional insight may result in modifications to the selection criteria within this process. Such modifications will result in an update of this document as appropriate.

Greenberg, H. S.↗

CHALLENGING SOME CONTEMPORARY VIEWS OF CORONAL MASS EJECTIONS. II. THE CASE FOR ABSENT FILAMENTS

When a coronal mass ejection (CME) appears in a coronagraph it often exhibits three parts. This “classic” three-part configuration consists of a bright leading edge, a dark circular- or teardrop-shaped cavity, and a bright core within the cavity. It is generally accepted that these are manifestations of coronal plasma pileup, the driving magnetic flux rope, and the associated eruptive filament, respectively. The latter has become accepted by the community since coronagraph CMEs have been commonly associated with eruptive filaments for over 40 years. In this second part of our series challenging views on CMEs, we present the case that the inner core of the three-part coronagraph CME may not be, and in the most common cases is not, a filament. We present our case in the form of four exhibits showing that most of the CMEs in a broad survey are not associated with an eruptive filament at the Sun, and that the cores of those CMEs that are filament-associated do not geometrically resemble or consist of material from the associated filament. We conclude with a discussion on the possible causes of the bright CME core and what happens to the filament material postlaunch. We discuss how the CME core could arise spontaneously from the eruption of a flux rope from the Sun, or could be the result of a mathematical caustic produced by the geometric projection of a twisted flux rope.

79 ASTRONOMY AND ASTROPHYSICS↗

Mission support plan STS-2

The plan defines the anticipated GSTDN/DOD station support and configuration requirements for a nominal flight with an orbital inclination of 38.4 degrees and a circular orbit of 120 nautical miles for the first 5 orbits and 137 nautical miles thereafter. A complete set of preliminary site configuration messages (SCM) define nominal station AOS/LOS times and configurations for S-Band and UHF support. This document is intended for use as a planning tool, providing the necessary guidelines and data base for SCM generation in support of STS-2.

Ibanez, F.↗

Nonreciprocity in circular magnetoplasma-filled waveguides above the cyclotron frequency

The electromagnetic behavior of a circular perfect electric conductor waveguide with various magnetoplasma filling configurations has been investigated near the cyclotron resonance region at 77 K with longitudinal magnetic bias. Faraday rotation in the forward and reverse directions along with the waveguide geometry effect provided the nonreciprocal attenuation to design an isolator for frequencies up to the terahertz region. Based on the finite element method, two-dimensional eigenvalue as well as three-dimensional numerical simulations are provided to illustrate the phenomena. Unprecedented performance was attained for the coaxial configuration in terms of the bias-to-frequency ratio. Other configurations were found to have some nonreciprocity as well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Constraining the Nature of the PDS 70 Protoplanets with VLTI/GRAVITY

We present K-band interferometric observations of the PDS 70 protoplanets along with their host star using VLTI/GRAVITY. We obtained K-band spectra and 100 μas precision astrometry of both PDS 70 b and c in two epochs, as well as spatially resolving the hot inner disk around the star. Rejecting unstable orbits, we found a nonzero eccentricity for PDS 70 b of 0.17 ± 0.06, a near-circular orbit for PDS 70 c, and an orbital configuration that is consistent with the planets migrating into a 2:1 mean motion resonance. Enforcing dynamical stability, we obtained a 95% upper limit on the mass of PDS 70 b of 10 M {sub Jup}, while the mass of PDS 70 c was unconstrained. The GRAVITY K-band spectra rules out pure blackbody models for the photospheres of both planets. Instead, the models with the most support from the data are planetary atmospheres that are dusty, but the nature of the dust is unclear. Any circumplanetary dust around these planets is not well constrained by the planets’ 1–5 μm spectral energy distributions (SEDs) and requires longer wavelength data to probe with SED analysis. However with VLTI/GRAVITY, we made the first observations of a circumplanetary environment with sub-astronomical-unit spatial resolution, placing an upper limit of 0.3 au on the size of a bright disk around PDS 70 b.

47 OTHER INSTRUMENTATION↗

Aeroacoustic characteristics of jet flap type exhausts.

This work which is intended to shed more light on the acoustic and fluid dynamic characteristics of jet flap type exhaust flows, reports and discusses some typical experimental results obtained with cold model air jets in a reverberation chamber. Acoustic data on the total sound power output and the overall noise spectrum of various jet flap configurations are given and compared with data from conventional circular jets. In addition various flow data for the same jets resulting from hot wire measurements are reported and general conclusions are obtained regarding the expected noise source distribution. The results indicate the dependence of the acoustic and flow characteristics on the major nozzle parameters. For the jet flaps the total radiated sound power is found to follow a 3 to 6 power of the exhaust velocity while for the circular jets the 8 power law is confirmed. The noise produced in the secondary mixing region downstream of the flap trailing edge tends to exceed the noise issuing from the primary mixing region.

Gruschka, H. D.↗