Search NASA⌕ Search

SEARCH · Search NASA

Results for “CUTTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Hollow needle used to cut metal honeycomb structures

Hollow needle tool cuts metal honeycomb structures without damaging adjacent material. The hollow needle combines an electrostatic discharge and a stream of oxygen at a common point to effect rapid, accurate metal cutting. The tool design can be varied to use the hollow needle principle for cutting a variety of shapes.

Gregg, E. A.↗

Modified soldering iron speeds cutting of synthetic materials

Modified soldering iron cuts large lots of synthetic materials economically without leaving frayed or jagged edges. The soldering iron is modified by machining an axial slot in its heating element tip and mounting a cutting disk in it. An alternate design has an axially threaded bore in the tip to permit the use of various shapes of cutting blades.

Schafer, W. G., Jr.↗

Study made of explosive cutting in simulated space environments

Study indicates the feasibility of explosive cutting and establishes techniques applicable to in-space cutting operations. Results show no degradation of the explosive and that work hardening of the target material is limited to the cut edge.

Coleman, E. R.↗

Refrigerated cutting tools improve machining of superalloys

Freon-12 applied to tool cutting edge evaporates quickly, leaves no residue, and permits higher cutting rate than with conventional coolants. This technique increases cutting rate on Rene-41 threefold and improves finish of machined surface.

Dudley, G. M.↗

An observation on tone cut-off in static test data from jet engine fans

The far-field acoustic data for eight full-scale fans tested at a NASA-Lewis outdoor facility were analyzed for the effect of a cut-off design feature where the number of rotor and stator blades are proportioned so that the blade-passage tone will not propagate. Inlet flow distortions, prevalent during static testing, interact with the rotor to generate tones that generally mask this cut-off phenomenon. Distortion tone properties previously evaluated are used to analyze the tones propagating from the aft fan duct. The analyzed data clearly differentiated the fans that are and are not cut-off.

Heidmann, M. F.↗

Flow stress model in metal cutting

A model for the plastic deformation that occurs in metal cutting, based on dislocation mechanics, is presented. The model explains the fundamental deformation structure that develops during machining and is based on the well known Cottrell-Stokes Law, wherein the flow stress is partitioned into two parts; an athermal part which occurs in the shear fronts (or shear bands); and a thermal part which occurs in the lamella regions. The deformation envokes the presence of a cellular dislocation distribution which always exists in the material ahead of the shear process. This 'alien' dislocation distribution either exists in the metal prior to cutting or is produced by the compressive stress field which operates in front of the shear process. The magnitude of the flow stress and direction of the shear are shown to be correlated to the stacking fault energy of the metal being cut. The model is tested with respect to energy consumption rates and found to be consistent with observed values.

Black, J. T.↗

Cutting a Tapered Edge on Padding Material

Resilience and flexibility of felt, rubber, or other padding materials allow them to be clamped in form block, cut straight down, and then released to produce straight clean tapered edge. With material held in slanted position, edge can be cut straight down; hence cut depth is minimum.

Mitchell, M. J.↗

Cutting Head for Ultrasonic Lithotripsy

Kidney stones lodged in urinary tract disintegrated with increased safety and efficiency by cutting head attached to end of vibrated wire probe. Aligns probe with stone and enables probe to vibrate long enough to disintegrate stone. Design of cutting head reduces risk of metal-fatigue-induced breakage of probe tip leaving metal fragments in urinary tract. Teeth of cutting head both seat and fragment kidney stone, while extension of collar into catheter lessens mechanical strain in probe wire, increasing probe life and lessening danger of in situ probe breakage.

Angulo, E. D.↗

Increasing Fatigue Lives of Laser-Cut Parts

Cut edges sanded to restore strength. Simple abrasion process removes transverse striations resulting from laser cutting of inconel 718 or equivalent alloy, increasing fatigue strengths of parts cut by laser beams. For stresses in range of 80 to 130 ksi (550 to 900 MPa) high cycle fatigue strengths restored to levels comparable to conventionally machined parts.

Glick, Edward W.↗

Enclosed Cutting-And-Polishing Apparatus

Proposed apparatus cuts and polishes specimens while preventing contamination of outside environment or of subsequent specimens processed in it. Designed for use in zero gravity but also includes features useful in cutting and polishing of toxic or otherwise hazardous materials on Earth. Includes remote manipulator for handling specimens, cutting and polishing wire, inlets for gas and liquid, and outlets for waste liquid and gas. Replaceable plastic liner surrounds working space.

Rossier, R. N.↗

Welding And Cutting A Nickel Alloy By Laser

Technique effective and energy-efficient. Report describes evaluation of laser welding and cutting of Inconel(R) 718. Notes that electron-beam welding processes developed for In-718, but difficult to use on large or complex structures. Cutting of In-718 by laser fast and produces only narrow kerf. Cut edge requires dressing, to endure fatigue.

Banas, C. M.↗

Impact of tether cutting on onboard navigation during the Tethered Satellite Mission-1

The first Tethered Satellite System mission (TSS-1) is manifested for Shuttle Flight STS-44 in January of 1991. The TSS mission presents a new challenge to engineers, requiring advanced guidance, navigation and control concepts. Current NASA flight rules require that the navigational state of the Orbiter at deorbit burn be known to an accuracy of 20 nautical miles. Response of the Shuttle crew to this contingency may involve cutting the tether prior to a complete retrieval. The degradation of the navigational state accuracy as modelled by Shuttle navigation system is examined. Responses to the loss of communication scenario are proposed for two cases. The first case examines navigational performance during a nominal attitude profile. The second case is identical to the first, with the inclusion of modelled tether electrodynamical forces. Comparisons of trajectories propagated from the onboard navigational state vector and a reference ephemeris state vector were performed, with the tether cut simulated at various points during the mission. Additionally, updates to the onboard navigational state via ground uplinks were provided prior to the assumed loss of communication. Through these comparisons, the onboard navigation state error was determined. Alternative responses result from efforts to minimize this error during the various phases of TSS-1 deployment. These results demonstrated existing NASA flight rules could be violated by cutting the tether, and suggests reponses to a loss of communications contingency to maintain a more accurate navigational state.

Pirker, Dana M.↗

Experimental investigations of the effects of cutting angle on chattering of a flexible manipulator

When a machine tool is mounted at the tip of a robotic manipulator, the manipulator becomes more flexible (the natural frequencies are lowered). Moreover, for a given flexible manipulator, its compliance will be different depending on feedback gains, configurations, and direction of interest. Here, the compliance of a manipulator is derived analytically, and its magnitude is represented as a compliance ellipsoid. Then, using a two-link flexible manipulator with an abrasive cut off saw, the experimental investigation shows that the chattering varies with the saw cutting angle due to different compliance. The main work is devoted to finding a desirable cutting angle which reduces the chattering.

Lew, J.↗

Self-pumped phase conjugation and four-wave mixing in 0- and 45-deg-cut n-type BaTiO3:Co

Relatively fast self-pumped phase-conjugate and four-wave-mixing rise times are reported in n-type cobalt-doped barium titanate. With the crystal oriented in a 45-deg cut as compared with the same crystal in a 0-deg cut we find a factor of 3 decrease in the 0-90-percent rise time to 800 ms with 25-mW input power at 514.5 nm. Also, the self-pumped phase-conjugate reflectivity increases from 20 to 40 percent. We deduce that the phase conjugation is from internally seeded stimulated photorefractive backscattering. The four-wave-mixing rise time of the 45-deg-cut crystal is 4 ms with a reflectivity of 48 percent when the pumping beams are derived from self-pumped phase conjugation that has an input power of 25 mW.

Garrett, M. H.↗

The Nichols Wing Cutting Equipment

Described here is wing cutting equipment for the economical production of metal wings for wind tunnel models. The machine will make any size of constant-section wing or strut up to one-sixth inch chord by 36-inch span and up to a thickness of one and one-quarter inches. It cuts a smooth, true model that is accurate to within two-thousandths of an inch on any ordinate. The holding jaws are so designed as to leave the model free of chip marks, and the only hand finishing necessary after the cutting is a rub with amunite to remove burrs. The actual change on ordinate in this finishing rub is less than .0002 inches.

Ford, James B↗

Stresses around large cut-outs in torsion boxes

The problem treated here is that of the stresses in a torsion box with a large rectangular cut-out. The theoretical treatment is confined to stresses termed the 'primary stresses.' Comparison of the theoretical results with strain gage data for a series of cut-outs indicates that the primary stresses are probably adequate for designing the major part of the structure, the only important exception being in the design of the cover sheet in the full section adjacent to the cut-out.

Kuhn, Paul↗

Some Factors Affecting the Reproducibility of Penetration and the Cut-Off of Oil Sprays for Fuel-injection Engines

This investigation was undertaken at the Langley Memorial Aeronautical Laboratory in connection with a general research on fuel-injection for aircraft. The purpose of the investigation was to determine the factors controlling the reproducibility of spray penetration and secondary discharges after cut-off. The development of single sprays from automatic injection valves was recorded by means of special high-speed photographic apparatus capable of taking 25 consecutive pictures of the moving spray at a rate of 4,000 per second. The effect of two types of injection valves, injection-valve tube length, initial pressure in the injection-valve tube, speed of the injection control mechanism, and time of spray cut-off, on the reproducibility of spray penetration, and on secondary discharges were investigated. It was found that neither type of injection valve materially affected spray reproducibility. The initial pressure in the injection-valve tube controlled the reproducibility of spray penetrations. An increase in the initial pressure or in the length of the injection-valve tube slightly increased the spray penetration within the limits of this investigation. The speed of the injection-control mechanism did not affect the penetration. Analysis of the results indicates that secondary discharges were caused in this apparatus by pressure waves initiated by the rapid opening of the cut-off valve. The secondary discharges were eliminated in this investigation by increasing the length of the injection-valve tube. (author)

Beardsley, E G↗