SEARCH · Search NASA

Results for “CYLINDER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Innovative design of composite structures: Axisymmetric deformations of unsymmetrically laminated cylinders loaded in axial compression

The study focuses on the axisymmetric deformation response of unsymmetrically laminate cylinders loaded in axial compression by known loads. A geometrically nonlinear analysis is used. Though buckling is not studied, the deformations can be considered to be the prebuckling response. Attention is directed at three 16 layer laminates: a (90 sub 8/0 sub 8) sub T; a (0 sub 8/90 sub 8) sub T and a (0/90) sub 4s. The symmetric laminate is used as a basis for comparison, while the two unsymmetric laminates were chosen because they have equal but opposite bending-stretching effects. Particular attention is given to the influence of the thermally-induced preloading deformations that accompany the cool-down of any unsymmetric laminate from the consolidation temperature. Simple support and clamped boundary conditions are considered. It is concluded that: (1) The radial deformations of an unsymmetric laminate are significantly larger than the radial deformations of a symmetric laminate, although for both symmetric and unsymmetric laminates the large deformations are confined to a boundary layer near the ends of the cylinder; (2) For this nonlinear problem the length of the boundary layer is a function of the applied load; (3) The sign of the radial deformations near the supported end of the cylinder depends strongly on the sense (sign) of the laminate asymmetry; (4) For unsymmetric laminates, ignoring the thermally-induced preloading deformations that accompany cool-down results in load-induced deformations that are under predicted; and (5) The support conditions strongly influence the response but the influence of the sense of asymmetry and the influence of the thermally-induced preloading deformations are independent of the support conditions.

Hyer, M. W.↗

NASA NTRS1989

Asymmetrical boundary layer separation at the base of a two cylinder geometry

This paper reports on the experimental description of the three-dimensional horseshoe vortex system occurring at the base of two cylinder mounted side by side on an endwall. The spacing between the two cylinders is adjusted to generate a family of viscous flows. Flow visualization performed in a water tunnel provides a qualitative understanding of the flow over a range of flow variables. A detailed wind tunnel experiment provides a quantitative description of the flow at a single test condition. At Re(D) = 2.5 x 10 to the 5th the measurements show an asymmetrical primary vortex with a wide flat cross section. A small counterrotating vortex is found between the primary vortex and the cylinder leading edge.

Boyle, M. T.↗

NASA NTRS1990

A model of filament-wound thin cylinders

A model was developed for simulating he manufacturing process of filament-wound cylinders made of a thermoset matrix composite. The model relates the process variables (winding speed, fiber tension, applied temperature) to the parameters characterizing the composite cylinder and the mandrel. The model is applicable to cylinders for which the diameter is large compared to the wall thickness. The model was implemented by a user-friendly computer code suitable for generating numerical results.

Calius, Emilio P.↗

NASA NTRS1990

Stabilization of Taylor-Couette flow due to time-periodic outer cylinder oscillation

The linear stability of circular Couette flow between concentric infinite cylinders is considered for the case when the inner cylinder is rotated at a constant angular velocity and the outer cylinder is driven sinusoidally in time with zero mean rotation. This configuration was studied experimentally by Walsh and Donnelly. The critical Reynolds numbers calculated from linear stability theory agree well with the experimental values, except at large modulation amplitudes and small frequencies. The theoretical values are obtained using Floquet theory implemented in two distinct approaches: a truncated Fourier series representation in time, and a fundamental solution matrix based on a Chebyshev pseudospectral representation in space. For large amplitude, low frequency modulation, the linear eigenfunctions are temporally complex, consisting of a quiescent region followed by rapid change in the perturbed flow velocities.

Murray, B. T.↗

NASA NTRS1990

Filament winding cylinders. II - Validation of the process model

Analytical and experimental studies were performed to validate the model developed by Lee and Springer for simulating the manufacturing process of filament wound composite cylinders. First, results calculated by the Lee-Springer model were compared to results of the Calius-Springer thin cylinder model. Second, temperatures and strains calculated by the Lee-Springer model were compared to data. The data used in these comparisons were generated during the course of this investigation with cylinders made of Hercules IM-6G/HBRF-55 and Fiberite T-300/976 graphite-epoxy tows. Good agreement was found between the calculated and measured stresses and strains, indicating that the model is a useful representation of the winding and curing processes.

Calius, Emilio P.↗

NASA NTRS1991

Analysis of flow on cones and cylinders using discrete vortex methods

Discrete vortex methods have been developed to investigate the vortex flows on cones and two-dimensional cylinders. The cone problem was solved by assuming that, to meet conical flow and zero-force conditions, the vortices move radially away from the body at a given cross-section. The two-dimensional cylinder problem was solved by limiting the velocity along the zero streamline surrounding the vortex field to two times freestream velocity and by limiting the lateral movement of the vortices. Variations in vortex position and strength with time were determined by taking into account the rate at which circulation is generated at separation points on the body. The calculated vortex positions and strengths were in good agreement with available experimental data. Viscous effects could be accounted for by adding empirically determined damping terms to the velocity equations. The models indicate that different types of asymmetry occur for the cone and two-dimensional cylinder. Asymmetry onset boundaries determined by the discrete vortex method show the same trend as experiment.

Gainer, Thomas G.↗

NASA NTRS1991

High frequency scattering from corrugated stratified cylinders

Interest in applying radar remote sensing for the study of forested areas led to the development of a model for scattering from corrugated stratified dielectric cylinders. The model is used to investigate the effect of bark and its roughness on scattering from tree trunks and branches. The outer layer of the cylinder (bark) is assumed to be a low-loss dielectric material and to have a regular (periodic) corrugation pattern. The inner layers are treated as lossy dielectrics with smooth boundaries. A hybrid solution based on the moment method and the physical optics approximation is obtained. In the solution, the corrugations are replaced with polarization currents that are identical to those of the local tangential periodic corrugated surface, and the stratified cylinder is replaced with equivalent surface currents. New expressions for the equivalent physical-optics currents are used which are more convenient than the standard ones. It is shown that the bark layer and its roughness both reduce the radar cross-section. It is also demonstrated that the corrugations can be replaced by an equivalent anisotropic layer.

Sarabandi, Kamal↗

NASA NTRS1991

Stability of the flow around a cylinder: The spin-up problem

A concern is the flow around an infinite cylinder, which at a certain instant impulsively starts to spin. The growth of vortices in the resulting boundary layer occurring outside the cylinder is investigated. This layer is essentially a Rayleigh layer which grows with time, so the mechanism involved is similar to that studied in Hall (1983). Vortices with wavenumber comparable to the layer thickness are shown to be described by partial differential equations that govern the system numerically. It is assumed that the Rayleigh layer is thin, so particles are confined to move in a path with radius of curvature the same as the cylinder. The Goertler number is a function of time, so the time scale which produces an order, is considered one Goertler number. The right hand branch calculation is considered by letting the time tend to infinity, also inviscid Goertler modes are considered.

Otto, S. R.↗

NASA NTRS1992

Bending response of thin-walled laminated composite cylinders

Closed-form linear response solutions are presented for the bending response of thin-walled laminated composite cylinders. Displacements and intralaminar stresses are computed using the Donnell theory, and interlaminar stresses are computed using 3D equilibrium equations of elasticity. Laminates with stacking sequencies and an aluminum cylinder are used to illustrate the displacement response, intralaminar, and interlaminar stresses for two length-to-radius ratios of 1 and 5. Data obtained indicate that if only fiber breakage causes ultimate failure, material failure will occur on the compression side of the cylinders, at the ends, due to fiber compression. The interlaminar normal stress is an order of magnitude smaller than the interlaminar shear stresses and it is not likely to initiate failure.

Fuchs, H. P.↗

NASA NTRS1993

In-flight investigation of a rotating cylinder-based structural excitation system for flutter testing

A research excitation system was test flown at the NASA Dryden Flight Research Facility on the two-seat F-16XL aircraft. The excitation system is a wingtip-mounted vane with a rotating slotted cylinder at the trailing edge. As the cylinder rotates during flight, the flow is alternately deflected upward and downward through the slot, resulting in a periodic lift force at twice the cylinder's rotational frequency. Flight testing was conducted to determine the excitation system's effectiveness in the subsonic and transonic flight regimes. Primary research objectives were to determine the system's ability to develop adequate force levels to excite the aircraft's structure and to determine the frequency range over which the system could excite structural modes of the aircraft. The results from the exciter were compared with results from atmospheric turbulence excitation at the same flight conditions. The results from the forced excitation were of higher quality and had less variation than the results from atmospheric turbulence. The forced excitation data also invariably yielded higher structural damping values than those from the atmospheric turbulence data.

Vernon, Lura↗

NASA NTRS1940

Analysis of Cylinder-pressure-indicator Diagrams Showing Effects of Mixture Strength and Spark Timing

An investigation was made to determine the effect of mixture strength and of normal as well as optimum spark timing on the combustion, on the cylinder temperature, and on the performance characteristics of an engine. A single-cylinder test unit utilizing an air-cooled cylinder and a carburetor and operating with gasoline having an octane rating of 92 was used. The investigation covered a range of fuel-air ratios from 0.053 to 0.118. Indicator diagrams and engine-performance data were taken for each change in engine conditions. Examination of the indicator shows that for fuel-air ratios less than and greater than 0.082 the rate and the amount of effective fuel burned decreased. For a fuel-air ratio of 0.118 the combustion efficiency was only 58 percent. Advancing the spark timing increased the rate of pressure rise. This effect was more pronounced with leaner mixtures.

Gerrish, Harold C↗

NASA NTRS1927

A Preliminary Study of Fuel Injection and Compression Ignition as Applied to an Aircraft Engine Cylinder

This report summarizes some results obtained with a single cylinder test engine at the Langley Field Laboratory during a preliminary investigation of the problem of applying fuel injection and compression ignition to aircraft engines. For this work a standard Liberty Engine cylinder was fitted with a high compression, 11.4 : 1 compression ratio, piston, and equipped with an airless injection system, including a primary fuel pump, an injection pump, and an automatic injection valve. The results obtained during this investigation have indicated the possibility of applying airless injection and compression ignition to a cylinder of this size, 8-inch bore by 7-inch stroke, when operating at engine speeds as high as 1,850 R. P. M. A minimum specific fuel consumption with diesel engine fuel oil of 0.30 pound per I. HP. Hour was obtained when developing about 16 B. HP. At 1,730 R. P. M.

Gardiner, Arthur W↗

NASA NTRS1936

The Effect of Baffles on the Temperature Distribution and Heat-transfer Coefficients of Finned Cylinders

This report presents the results of an investigation to determine the effect of baffles on the temperature distribution and the heat-transfer coefficient of finned cylinders. The tests were conducted in a 30-inch wind tunnel on electrically heated cylinders with fins of 0.25 and 0.31 inch pitch. The results of these tests showed that the use of integral baffles gave a reduction of 31.9 percent in the rear wall temperatures and an increase of 54.2 percent in the heat transfer coefficient as compared with a cylinder without baffles.

Schey, Oscar W↗

NASA NTRS1937

Blower Cooling of Finned Cylinders

Several electrically heated finned steel cylinders enclosed in jackets were cooled by air from a blower. The effect of the air conditions and fin dimensions on the average surface heat-transfer coefficient q and the power required to force the air around the cylinders were determined. Tests were conducted at air velocities between the fins from 10 to 130 miles per hour and at specific weights of the air varying from 0.046 to 0.074 pound per cubic foot. The fin dimensions of the cylinders covered a range in pitches from 0.057 to 0.25 inch average fin thicknesses from 0.035 to 0.04 inch, and fin widths from 0.67 to 1.22 inches.

Schey, Oscar W↗

NASA NTRS1946

Effect of compressibility at high subsonic velocities on the lifting force acting on an elliptic cylinder

An extended form of the Ackeret iteration method, applicable to arbitrary profiles, is utilized to calculate the compressible flow at high subsonic velocities past an elliptic cylinder. The angle of attack to the direction of the undisturbed stream is small and the circulation is fixed by the Kutta condition at the trailing end of the major axis. The expression for the lifting force on the elliptic cylinder is derived and shows a first-step improvement of the Prandtl-Glauert rule. It is further shown that the expression for the lifting force, although derived specifically for an elliptic cylinder, may be extended to arbitrary symmetrical profiles.

Kaplan, Carl↗

NASA NTRS1947

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.

Batdorf, S B↗

NASA NTRS1957

On panel flutter and divergence of infinitely long unstiffened and ring-stiffened thin-walled circular cylinders

A preliminary theoretical investigation of the panel flutter and divergence of infinitely long, unstiffened and ring-stiffened thin-walled circular cylinders is described. Linearized unsteady potential-flow theory is utilized in conjunction with Donnell's cylinder theory to obtain equilibrium equations for panel flutter. Where necessary, a simplified version of Flugge's cylinder theory is used to obtain greater accuracy. By applying Nyquist diagram techniques, analytical criteria for the location of stability boundaries are derived. A limited number of computed results are presented.

Leonard, Robert W↗

NASA NTRS1993

Extinction efficiencies from DDA calculations solved for finite circular cylinders and disks

One of the most commonly noted uncertainties with respect to the modeling of cirrus clouds and their effect upon the planetary radiation balance is the disputed validity of the use of Mie scattering results as an approximation to the scattering results of the hexagonal plates and columns found in cirrus clouds. This approximation has historically been a kind of default, a result of the lack of an appropriate analytical solution of Maxwell's equations to particles other than infinite cylinders and spheroids. Recently, however, the use of such approximate techniques as the Discrete Dipole Approximation has made scattering solutions on such particles a computationally intensive but feasible possibility. In this study, the Discrete Dipole Approximation (DDA) developed by Flatau (1992) is used to find such solutions for homogeneous, circular cylinders and disks. This can serve to not only assess the validity of the current radiative transfer schemes which are available for the study of cirrus but also to extend the current approximation of equivalent spheres to an approximation of second order, homogeneous finite circular cylinders and disks. The results will be presented in the form of a single variable, the extinction efficiency.

Withrow, J. R.↗