Search NASA⌕ Search

SEARCH · Search NASA

Results for “Checking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Jig Quickly Checks Connector Pin Alinement

Test jig checks whether pins of connector are within location tolerance. Jig greatly reduces test time. Machined slots on opposite faces of plate form matrix of rectangular windows at intersections. If connector pin is out of alinement, it makes electrical contact with side of window, triggering indicator.

Hall, W. M.↗

Advanced Microbial Check Valve development

The Microbial Check Valve (MCV) is a flight qualified assembly that provides bacteriologically safe drinking water for the Space Shuttle. The 1-lb unit is basically a canister packed with an iodinated ion-exchange resin. The device is used to destroy organisms in a water stream as the water passes through it. It is equally effective for fluid flow in either direction and its primary method of disinfection is killing rather than filtering. The MCV was developed to disinfect the fuel cell water and to prevent back contamination of stored potable water on the Space Shuttle. This paper reports its potential for space applications beyond the basic Shuttle mission. Data are presented that indicate the MCV is suitable for use in advanced systems that NASA has under development for the reclamation of humidity condensate, wash water and human urine.

Colombo, G. V.↗

Wind-Tunnel-Model Leak-Checking System

Voice-actuated system allows one operator to do work of three. System uses voice-recognition-and-response unit and graphics terminal to interact with technician and to provide technician visual feedback. Computer-based Leakcheck system allows computer to do more of total work in checking model for leaks to reduce time and manpower required to perform task.

Larson, W. E.↗

Seismic analysis of the large 70-meter antenna. Part 2: General dynamic response and a seismic safety check

An extensive dynamic analysis for the new JPL 70-meter antenna structure is presented. Analytical procedures are based on the normal mode decomposition which include dumping and special forcing functions. The dynamic response can be obtained for any arbitrarily selected point on the structure. A new computer program for computing the time-dependent, resultant structural displacement, summing the effects of all participating modes, was developed also. Program compatibility with natural frequency analysis output was verified. The program was applied to the JPL 70-meter antenna structure and the dynamic response for several specially selected points was computed. Seismic analysis of structures, a special application of the general dynamic analysis, is based also on the normal modal decomposition. Strength specification of the antenna, with respect to the earthquake excitation, is done by using the common response spectra. The results indicated basically a safe design under an assumed 5% or more damping coefficient. However, for the antenna located at Goldstone, with more active seismic environment, this study strongly recommends and experimental program that determines the true damping coefficient for a more reliable safety check.

Kiedron, K.↗

In-situ technique for checking the calibration of platinum resistance thermometers

The applicability of the self-heating technique for checking the calibration of platinum resistance thermometers located inside wind tunnels was investigated. This technique is based on a steady state measurement of resistance increase versus joule heating. This method was found to be undesirable, mainly because of the fluctuations of flow variables during any wind tunnel testing.

Daryabeigi, Kamran↗

Quick Check Of Butt-Weld Alignment

Proposed tool measures alignments of plates before butt-welded. Provides nearly instantaneous check on alignment, thereby facilitating repetitive measurements along length of weld joint. Reduces risk of contamination of weld from dirty measuring tools. Middle photodetector indicates acceptable alignment when position of transmitter fiber preciously matches that of center receiver fiber. If plates offset, other photodetectors signal misalignment.

Smith, Matthew A.↗

Checking Automated-Welder Programs By Computer

Computer system detects and displays actual and potential errors in programs for computer-controlled electron-beam welder. Uses personal computer, separate from welding computer. Programmed specifically to highlight errors in welding program. Eliminates need for preweld full-power test run reducing checkout time to about half hour. Assures much higher quality, damage-free welding. Used to create and edit new programs for welder. Control computer thereby free for production. Useful for checking programs for such other computer-controlled equipment as inertia welders, robots, machine tools, and heat treaters.

Damicone, L. O.↗

Solar sensor subsystems alignment check using solar scans for the Halogen Occultation Experiment

The alignment of a dual-axes sun sensor subsystem to a telescope having a multiple sensor subsystem is described. The sun sensor consists of two analog and one digital silicon detectors. The analog detectors are shadow mask type operating in the visible spectrum. The detectors are mounted for azimuth and elevation positioning of biaxial gimbals. The digital detector is a linear diode array that operates at a spectral position of 0.7 micron and is used for elevation positioning. The position signals correspond to relative angles between the sun sensor and the solar disk. These three detectors are aligned on an Invar structure which is mounted to a Cassegrain telescope. This telescope relays solar radiance to an eight channel detector subsystem operating in the infrared range from 2 to 10 microns. The test technique and results to check the boresight alignment of these two subsystems by scanning the solar disk will be reported. The boresight alignment for both the azimuth and elevation axes of the two detector subsystems is verified using this technique.

Jurczyk, S. G.↗

Calibration Check For Programmed Welding Robot

Preweld calibration check helps to ensure welding torch on computer-controlled welding robot mounted properly, right gas cup selected, and length of extension of electrode adjusted correctly. Performed by operator just before dry run for each set of parts welded. Procedure takes 2 to 3 minutes and enables correction of errors before parts or equipment damaged.

Sliwinski, Karen E.↗

Self-checking sequential circuit design using m-out-of-n codes

A technique for designing sequential circuits which are totally self-checking for single stuck at faults is presented. This technique uses m-out-of-n codes for state assignments and for output encoding. The next stage logic and the output logic are implemented such that any stuck-at-fault will either create a single bit error or unidirectional multibit error at the output. The technique has been applied to MCNC benchmark circuits and the overhead is estimated.

Busaba, F. Y.↗

Nonlinear smoothing identification algorithm with application to data consistency checks

A parameter identification algorithm for nonlinear systems is presented. It is based on smoothing test data with successively improved sets of model parameters. The smoothing, which is iterative, provides all of the information needed to compute the gradients of the smoothing performance measure with respect to the parameters. The parameters are updated using a quasi-Newton procedure, until convergence is achieved. The advantage of this algorithm over standard maximum likelihood identification algorithms is the computational savings in calculating the gradient. This algorithm was used for flight-test data consistency checks based on a nonlinear model of aircraft kinematics. Measurement biases and scale factors were identified. The advantages of the presented algorithm and model are discussed.

Idan, M.↗

Regenerable Microbial Check Valve - Life cycle tests results

Life cycle regeneration testing of the Microbial Check Valve (MCV) that is used on the Shuttle Orbiter to provide microbial control of potable water is currently in progress. Four beds are being challenged with simulated reclaimed waters and repeatedly regenerated. Preliminary results indicate that contaminant systems exhibit unique regeneration periodicities. Cyclic throughput diminishes with increasing cumulative flow. It is considered to be feasible to design a regenerable MCV system which will function without human intervention and with minimal resupply penalty for the 30 year life of the Space Station.

Atwater, James E.↗

Magnetic Check Valve

Poppet in proposed check valve restored to closed condition by magnetic attraction instead of spring force. Oscillations suppressed, with consequent reduction of wear. Stationary magnetic disk mounted just upstream of poppet, also containing magnet. Valve body nonmagnetic. Forward pressure or flow would push poppet away from stationary magnetic disk so fluid flows easily around poppet. Stop in valve body prevents poppet from being swept away. When flow stopped or started to reverse, magnetic attraction draws poppet back to disk. Poppet then engages floating O-ring, thereby closing valve and preventing reverse flow. Floating O-ring facilitates sealing at low loads.

Morris, Brian G.↗

Dashpot Damps Oscillations In Check Valve

Operation of check valve improved by redesigning poppet and adding two new components: dashpot and dashpot ring between dashpot and poppet. Modifications eliminate self-sustaining poppet oscillations that cause premature wear and jamming of poppet mechanism.

Morris, Brian G.↗

Check valve with poppet damping mechanism

An inline check valve for a flow line is presented where the valve element is guided for inline travel forward and rearward of a valve sealing member and is spring biased to a closed sealing condition. One of the guides for the valve element includes a dashpot bore and plunger member to control the rate of travel of the valve element in either direction as well as provided a guiding function. The dashpot is not anchored to the valve body so that the valve can be functional even if the plunger member becomes jammed in the dashpot.

Morris, Brian G.↗

Check valve with poppet dashpot/frictional damping mechanism

An inline check valve for a flow line where the valve element is guided for inline travel forward and rearward of a valve sealing member and is spring biased to a closed sealing condition is presented. One of the guides for the valve element includes a dashpot housing with a bore and plunger member to control the rate of travel of the valve element in either direction, providing a guiding function. The plunger member is arranged with a dashpot ring to frictionally contact the dashpot bore and has an interior tortuous flow path from one side to the other side of the dashpot ring. The dashpot housing is not anchored to the valve body so that the valve can be functional even if the dashpot ring becomes jammed in the dashpot housing.

Morris, Brian G.↗

Magnetically operated check valve

A magnetically operated check valve is disclosed. The valve is comprised of a valve body and a movable poppet disposed therein. A magnet attracts the poppet to hold the valve shut until the force of fluid flow through the valve overcomes the magnetic attraction and moves the poppet to an unseated, open position. The poppet and magnet are configured and disposed to trap a magnetically attracted particulate and prevent it from flowing to a valve seating region.

Morris, Brian G.↗