Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Low cost scroll compressor or vacuum pump

A low cost scroll device and methods of manufacturing the same are described. The scroll device includes, for example, a drive pin hole and bearing bores machined into a scroll of the scroll device from the same side as the involute of the scroll; idler shaft assemblies with no more than one bearing in the orbiting scroll for mechanically coupling the orbiting scroll to the fixed scroll; and an epoxy coating applied using a process that requires assembly of the scroll device only once.

Mesward, Joshua R.↗
DOE OSTI2022

Nafion Passivation of c-Si Surface and Edge for Electron Paramagnetic Resonance

Effective surface passivation of crystalline silicon (c-Si) surface by reducing the carrier recombination rate has led to modern c-Si solar cells with efficiencies > 25% in both laboratory and industrial settings. Typical mainstream surface passivation techniques include high-temperature silicon oxide (SiOx), amorphous silicon (a-Si:H), hydrogen-rich silicon nitride (SiNx), and aluminum oxide (Al2O3) [1]. They have demonstrated excellent surface recombination velocity of < 1 cm/s owing to both chemical passivation (via the hydrogen saturation of Si dangling bonds at the c-Si surface), and field-effect passivation (via the band bending from the fixed charge of the dielectric layers). Recently, several groups have studied solution-based organic materials for c-Si passivation, including bis(trifluoromethane)sulfonimide (TFSI), polystyrenesulfonate, and Nafion [2, 3] via spin or dip coating. All films were processed at ambient room temperature, and a high lifetime of 12 ms, as well as a low saturation current density (J0) of 16 fA/cm2, have been demonstrated using Nafion passivation [2]. However, despite the air instability, Nafion has several advantages when introduced to PV applications: (a) Wafer quality can be measured at high throughput after several process stages. (b) It is compatible with PL mapping, compared to HF liquid passivation which cannot be performed in room ambient. (c) Nafion process is fast and poses fewer constraints on process complexity, and cleanness, compared to Al2O3 and a-Si:H passivation. (d) Nafion is the ideal room temperature passivation, which can be applied onto a small fragment of a degraded module to investigate microscopic mechanisms when studying degradation mechanisms. Edge passivation is needed for advanced characterization tests such as Electron Paramagnetic Resonance (EPR), Electrically Detected Magnetic Resonance (EDMR), Deep Level Transient Spectroscopy (DLTS), local cell current-voltage (J-V), and Suns-Voc. In such cases, the laser-damaged minicell edges will obscure the true degradation mechanisms, and Nafion can effectively passivate them without causing further degradation through elevated-temperature processes. In this contribution, we show the passivation results of Nafion on bare nCz and compare it with a Al2O3 witness. We highlight the importance of edge pre-treatment before Nafion to achieve good passivation. We show that Nafion can reach decent passivation without undergoing high-temperature processes. We also explore the temperature dependency of Nafion through photoluminescence (PL) study and demonstrate the application of Nafion under cryogenic temperature (~6 K) through EPR. Our results reveal that Nafion can reduce surface and edge Si dangling bonds at low temperatures. Thus, it can be used as an effective room temperature passivation technique for advanced characterization methods.

c-Si↗
DOE OSTI2025

Reducing Mass of Steel Auto Bodies using Thin Advanced High Strength Steel with Carbon-Fiber Reinforced Epoxy

Diversitak, a company based in Detroit, MI, has developed a proprietary, low specific gravity, carbon fiber-reinforced epoxy (CFRE) under U.S. patent number 9,963,58832. Preliminary testing on this new material conducted in collaboration with ArcelorMittal Steel Company proved out the CFRE concept. A thin layer of this CFRE was applied to a stamped sheet of steel with residual stamping oils from a mill, in a time corresponding to automotive processing (e.g., ~15 seconds), and processed following automotive e-coat procedures (phosphating + 175–200°C heating), to complete the curing. No problems with adherence or performance were noted. While the CFRE does add weight to a thin gauge steel panel, it weighs much less than what is displaced by using thicker conventional mild steel gauges. The application of the coating showed a significant increased dent resistance, oil canning resistance, and part stiffness.This current two-year project was designed to mature this new technology to near manufacturing readiness to reduce the weight of a vehicle and lower the cost of weight reduction. The process involves the use of thinner gauge steels than are currently used. The collaborative development team included two industrial manufacturers: Diversitak and ArcelorMittal Steel Company; LightMAT; and two National Laboratories: Oak Ridge National Laboratory (ORNL) and Idaho National Laboratory (INL). The team developed a new manufacturing process to reduce the weight of a vehicle and lower the cost of weight reduction, as well as a better understanding of how to apply the coating so that it will perform to a high standard in-service. The team also performed an in-depth study to determine the long-term durability of the materials manufactured using this technology and well-known automotive industry standard tests.The overall process involved stiffening the thinner gauge steel by applying the CFRE on only one side. To accomplish this goal, the optimal reinforcement fiber length and fiber concentration was first determined. This was followed by measuring the coefficient of thermal expansion (CTE) in all three directions, so it could be fed into manufacturing models and methods for rapidly and inexpensively applying the coating. This was followed by panel level evaluations of the coating and steel combination, and then by full part demonstration of the technology on door panels. The final step was corrosion testing of the parts.ArcelorMittal characterized the advanced high strength steel (AHSS) (e.g., metallurgy-heat treatment for required AHSS properties as a function of the sheet thickness, state of internal stress) and quantified CFRE adhesion to the steel as a function of sheet preparation (e.g., rolling and stamping).ORNL optimized the fiber length, fiber concentration, and coating thickness for best vehicle function and performance at the least cost. Along with the suppliers, ORNL developed a durable CFRE application process (e.g., gun material, design, robotic dispensing process) and identified the adhesion stability of the CFRE during process holding. An approach to ensure that application/curing timing conforms to conventional assembly line speed and plant cycle times was determined. ORNL also determined the CTE of the material in all three directions and performed material scanning electron microscopy (SEM) analyses.INL characterized the corrosion properties of the steel panels coated with CFRE. The panels were investigated for corrosion resistance and stability as replacement materials used in automotive body panels to reduce mass. The coupons tested at INL were supplied by Diversitak after an optimized CFRE formulation was achieved in the already coated form for corrosion testing.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2019

Experimental and Numerical Study of Coating Thickness Using Multi-slot Air Knives

Gas-jet wiping is a widely employed production technology for controlling the final zinc coating thickness on a moving substrate during continuous hot-dip galvanizing. This paper presents an experimental investigation and numerical analysis of a prototype multi-slot air knife, which offers an increase in wiping efficiency relative to the traditional single-slot jet geometry in the continuous galvanizing process. The applicability of the analytical coating weight model of Elsaadawy et al. (Metall Mater Trans B, 38:413-424, 2007) to predict the final coating weight was determined for the multi-slot geometry, where particular focus was devoted to the effect of geometric parameters. Experimental measurements under a variety of knife geometry and process conditions agreed with the coating weight predictions of the analytical model. It was also shown that the air-knife geometric parameters had a significant effect on the pressure profile and shear stress distribution applied by the air knives to the moving substrate. It was determined that the final coating thickness was significantly affected by the auxiliary jet width, D{sub a}, where lighter coating weights at higher strip velocities (up to 5.4 pct at V{sub s} = 1.5 m/s) could be achieved by using the multi-slot air-knives prototype vs. the conventional single-slot configuration.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultrathick Boron Carbide Coatings for Nuclear Fusion Targets

Boron carbide is an attractive ablator for next-generation inertial confinement fusion (ICF) targets. Here we describe several aspects of our ongoing systematic studies of the deposition and processing of B 4 C coatings for ICF targets. We show that residual compressive stress in films can be reduced and the deposition rate increased by N-doping. Further, we also demonstrate successful Si substrate etching and surface polishing and discuss remaining challenges and offer potential solutions to the buildup of particulates in the deposition chamber during prolonged coating runs, control of nodular growth defects, and lateral nonuniformity of film properties for deposition conditions with relatively low target-to-substrate distances.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Controlling Polymer Morphology in Blade-Coated All-Polymer Solar Cells

In this report translating all-polymer solar cells from spin-coating to scalable roll-to-roll-compatible fabrication techniques is a critical step toward the application of organic photovoltaics at a scale. Techniques to control polymer crystallization and phase separation during solution printing are essential to obtain high-performance printed organic solar cells. Here, we demonstrate a novel solvent additive approach employing trace amounts of phthalates as additives to control polymer crystallinity and suppress unfavorable phase separation in a representative PTB7-Th/P(NDI2OD-2T) all-polymer solar cell. The best-performing additive increased the blade-coated device performance from 2.09 to 4.50% power conversion efficiency, an over twofold improvement, mitigating the loss in performance that is typically observed during process transfer from spin-coating to blade-coating. It is suggested that the improved device performance stems from a finer polymer phase-separation size and overall improved active layer morphology, evidenced by device characterization data and indirectly supported by grazing incidence wide-angle X-ray scattering analyses. Real-time X-ray diffraction measurements during blade-coating provide mechanistic insights and suggest that the dioctyl phthalate additive may act as a compatibilizer, reducing the demixing of the donor and acceptor polymer during film formation, enabling a smaller phase separation and improved performance. The structural diversity of the class of phthalate additives makes this simple yet effective concept promising for translating other all-polymer material systems to blade-coating and other scalable printing techniques.

14 SOLAR ENERGY↗
DOE OSTI2022

Rapid scalable fabrication of roll-to-roll slot-die coated flexible perovskite solar cells using intense pulse light annealing

Perovskite solar cells have achieved high efficiencies at the lab scale using batch processes that often may not be scalable. Processes that can be integrated into a continuous manufacturing platform, such as roll-to-roll, where several processes can be carried out sequentially are necessary to develop a new cost-competitive solar technology. In this work, intense pulsed light thermal post-processing is coupled with scalable slot-die coating and air knife evaporation in a high-speed roll-to-roll process of up to 2 m min –1 . The optimization of IPL energy parameters, web speeds, solution flow rates, and concentration of precursor inks yielded a champion power conversion efficiency of 11.24% for a 1 cm 2 roll-to-roll coated device. The overall processing time for a single layer in this process is reduced from minutes to seconds and the overall footprint of the manufacturing process is decreased. Furthermore, this demonstrates the promising capabilities for intensed pulsed light to reduce manufacturing costs and paves a roadmap for scalable and efficient PSCs on a roll-to-roll platform.

14 SOLAR ENERGY↗
DOE OSTI2021

Comparison of the Mechanical Properties of a Conjugated Polymer Deposited Using Spin Coating, Interfacial Spreading, Solution Shearing, and Spray Coating

The mechanical properties of π-conjugated (semiconducting) polymers are a key determinant of the stability and manufacturability of devices envisioned for applications in energy and healthcare. These properties—including modulus, extensibility, toughness, and strength—are influenced by the morphology of the solid film, which depends on the method of processing. To date, the majority of work done on the mechanical properties of semiconducting polymers has been performed on films deposited by spin coating, a process not amenable to the manufacturing of large-area films. Here, we compare the mechanical properties of thin films of regioregular poly(3-heptylthiophene) (P3HpT) produced by three scalable deposition processes—interfacial spreading, solution shearing, and spray coating—and spin coating (as a reference). Our results lead to four principal conclusions. (1) Spray-coated films have poor mechanical robustness due to defects and inhomogeneous thickness. (2) Sheared films show the highest modulus, strength, and toughness, likely resulting from a decrease in free volume. (3) Interfacially spread films show a lower modulus but greater fracture strain than spin-coated films. (4) The trends observed in the tensile behavior of films cast using different deposition processes held true for both P3HpT and poly(3-butylthiophene) (P3BT), an analogue with a higher glass transition temperature. Grazing incidence X-ray diffraction and ultraviolet–visible spectroscopy reveal many notable differences in the solid structures of P3HpT films generated by all four processes. Herein, while these morphological differences provide possible explanations for differences in the electronic properties (hole mobility), we find that the mechanical properties of the film are dominated by the free volume and surface topography. In field-effect transistors, spread films had mobilities more than 1 magnitude greater than any other films, likely due to a relatively high proportion of edge-on texturing and long coherence length in the crystalline domains. Overall, spread films offer the best combination of deformability and charge-transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Embedding of Optical Fibers with Electric Field Assisted Sintering

The Electric Field Assisted Sintering (EFAS) technique was used for embedding the fibers, involving rapid heating via an electric current and pressure, reducing fiber exposure to high temperatures. Stainless steel guide tubes were inserted at the fiber-matrix junctions to prevent fiber breakage during the sintering process. The study varied key EFAS parameters—temperature (800°C to 980°C), pressure (40-50 MPa), and hold time (5-10 minutes)—to assess how they influenced fiber embedding. After embedding, the fibers were inspected using optical frequency domain reflectometry (OFDR) to evaluate optical losses and strain along the fiber length. The OFDR scans confirmed that the fibers remained intact, and subsequent transmission tests demonstrated no macroscopic fractures. The embedded samples were also analyzed using scanning electron microscopy (SEM) and X-ray computed tomography (CT) scans. These tests confirmed good bonding between the fiber and matrix with no cracking, though some porosity was present in samples fabricated at lower temperatures. At higher temperatures (980°C), the fiber-matrix bonding was continuous and defect-free, with metal coatings aiding in the bonding process. Elemental analysis showed interdiffusion between the fiber coatings and matrix materials, particularly between the gold coating and stainless steel. Helium leak tests revealed that lower sintering temperatures resulted in matrix porosity, causing leaks, but samples fabricated at 980°C were leak-tight.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2025

Improved thermoelectric performance in Cr-doped two-dimensional Bi 2 Te 3

Thermoelectric materials with high electrical conductivity and low thermal conductivity (e.g., Bi 2 Te 3 ) can efficiently convert waste heat into electricity. However, despite favorable theoretical predictions, individual Bi 2 Te 3 nanostructures such as two-dimensional (2D) nanoplates tend to underperform bulk Bi 2 Te 3 . We report a novel surface doping technique to synthesize highly n-type Bi 2 Te 3 nanoplates using an external Cr coating followed by a thermal annealing process in a reducing atmosphere, as well as the mechanism by which this surface coating – only a few atoms or less in thickness – can observably impact the thermoelectric performance of 2D Bi 2 Te 3 . The Cr atoms act as n-type carrier donors by directly incorporating into the Bi 2 Te 3 structure during thermal annealing, enhancing electrical conductivity by ∼ 70 % while increasing thermal conductivity by only ∼ 5 % at room temperature. Compared to the uncoated Bi 2 Te 3 nanoplate, the Cr-doped Bi 2 Te 3 nanoplate exhibits a doubled thermoelectric figure of merit (zT), which is still relatively low. Raman spectroscopy and chemical potential simulations further confirm that Cr atoms are incorporated into the Bi 2 Te 3 structure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Performance evaluation of an air conditioning system based on quasi isothermal dehumidifcation

This work presents a first study of novel air conditioning system based on quasi isothermal dehumidification combined with dew-point evaporative cooling through the Maisotsenko cycle (M-Cycle). The dehumidification process is realized in desiccant coated heat exchanger with heat rejection system. The key idea behind the solution is to maximize the cooling effectiveness by creating favourable conditions for dehumidification and evaporative cooling process. This is achieved by rejecting the heat of sorption in the desiccant system and providing cold and dry air for M-Cycle air cooler, which allows the system to be powered by using low-grade heat energy at 50 °C. The analysis is performed on the basis of experimentally validated numerical models of each component combined in a unified model of the system. The goal of the study is to determine the performance of the solution under different operational conditions. In addition two types of M-Cycle air coolers (i.e. cross-flow and regenerative unit) are compared to establish which unit is more suitable as the source of cooling energy for the system. It was established that proposed system is able to provide comfortable room parameters (supply air temperature equal 17 °C and humidity ratio equal 0.010 kg/kg-da) for outdoor air temperatures ranging from 28 to 36 °C and outdoor air humidity ranging from 0.010 to 0.018 kg/kg-da. This means that the proposed solution is able to provide comfortable conditions in temperate and humid climates. Results also indicate that the system consisting of the regenerative M-Cycle HMX allows better cooling load management, offers higher thermal Coefficient of Performance (COP th ) and uses less water compared to the system with the cross-flow HMX. However, the system with cross-flow heat and mass exchanger (HMX) has a relatively greater electrical Coefficient of Performance (COP el ) in most cases.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

The Importance of Nonequilibrium to Equilibrium Transition Pathways for the Efficiency and Stability of Organic Solar Cells

Controlled morphology of solution-processed thin films have realized impressive achievements for non-fullerene acceptor (NFA)–based organic solar cells (OSCs). Given the large set of donor–acceptor pairs, employing various processing conditions to realize optimal morphology for high efficiency and stable OSCs is a strenuous task. Therefore, comprehensive correlations between processing conditions and morphology evolution pathways have to be developed for efficient performance and stability of devices. Within the framework of the blend system, crystallization transitions of NFA molecules are tracked utilizing the first heating scan of differential scanning calorimeter (DSC) measurement correlating with respective morphology evolution of blend films. Real-time dynamics measurements and morphology characterizations are combined to provide optimal morphology transition pathways as NFA molecules are shown to be released from the mixed phase to form balanced ordered packing with variant processing conditions. Polymer:NFA films are fabricated using blade coating incorporating solvent additive or thermal annealing as processing conditions as a correlation is formulated between performance and stability of solar cells with morphology transition pathways. In conclusion, this work demonstrates the significance of processing condition-controlled transition pathways for the realization of optimal morphology leading to superior OSC devices.

14 SOLAR ENERGY↗
DOE OSTI2024

Formation and degradation mechanism of methylammonium lead iodide perovskite thin film fabricated by electrospray technique

Electrospray deposition technique has been reported previously for fabricating effective and stable perovskite thin film, leading to efficient perovskite solar cells. Here, in this work, a comprehensive investigation of the formation mechanism of methylammonium lead iodide perovskite (CH 3 NH 3 PbI 3 ) film by electrospray technique is demonstrated and compared to the formation mechanism through the conventional spin coating technique. In the electrospray process, charged MAI nanoparticles are gradually introduced onto the PbI 2 film, intercalating within the PbI 2 structure to produce the perovskite film. In contrast, the spin-coating method involves supplying the MAI solution in bulk, leading to perovskite crystal formation through the dissolution of the PbI 2 layer by the MAI solution, followed by recrystallization into perovskite oriented in the [110] direction, 30° inclined to the substrate. The impact of charge and the electric field on the formation of perovskite film using the electrospray is explored. Furthermore, the intrinsic stability of perovskite films is monitored in real-time in a highly humid environment (≥80 % relative humidity (RH)) using in-situ Grazing Incidence Wide Angle X-ray Scattering (GIWAXS), and a degradation mechanism is proposed to enhance the durability of the perovskite-based devices. The study further delves into the comparison of the stability of electrosprayed and spin-coated perovskite film, and the impact of humidity level and the presence of a hole-transporting layer on the stability of the perovskite layer. Overall, this work provides a detailed understanding of the formation and humidity-induced degradation mechanism of electrosprayed perovskite films, offering insights that can extend to various applications of perovskite materials.

14 SOLAR ENERGY↗
DOE OSTI2021

Adhesion of Titanium Coatings on Additively Manufactured Stainless Steel [Slides]

Additive manufacturing can improve fuel cell development by increasing design development speed, enabling complex designs through more flexible fabrication, and reducing wasted excess material. The goal of the project is to develop a process for strongly adhering a coating of titanium to additively manufactured stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Versatile acid solvents for pristine carbon nanotube assembly

Chlorosulfonic acid and oleum are ideal solvents for enabling the transformation of disordered carbon nanotubes (CNTs) into precise and highly functional morphologies. Currently, processing these solvents using extrusion techniques presents complications due to chemical compatibility, which constrain equipment and substrate material options. Here, we present a novel acid solvent system based on methanesulfonic or p-toluenesulfonic acids with low corrosivity, which form true solutions of CNTs at concentrations as high as 10 g/liter (≈0.7 volume %). The versatility of this solvent system is demonstrated by drop-in application to conventional manufacturing processes such as slot die coating, solution spinning continuous fibers, and 3D printing aerogels. Through continuous slot coating, we achieve state-of-the-art optoelectronic performance (83.6 %T and 14 ohm/sq) at industrially relevant production speeds. This work establishes practical and efficient means for scalable processing of CNT into advanced materials with properties suitable for a wide range of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Annealing temperature variation and its influence on the self-cleaning properties of TiO 2 thin films

Titanium dioxide (TiO 2 ) is an important material in science and engineering because of its basic and synthetic properties. Nevertheless, there is a dearth of reports in the open literature focusing on its ability to self-clean under temperature changes. In this study, we used the spin coating technique to produce TiO 2 thin films to evaluate its self-cleaning ability after annealing at different temperatures. The TiO 2 sol was obtained through an endothermal sol-gel process, and the gel was coated on a glass substrate using a spin coater. The deposited films were then annealed at 400 °C, 600 °C, and 800 °C for 1 h. The influence of annealing temperature variation on the self-cleaning properties of the thin film was characterized using X-ray diffraction, scanning electron microscope; Fourier transformed infrared spectrometric analysis and UV-vis spectrophotometer. A test to ascertain self-cleaning was conducted using the degradation of methylene blue, and the different films were tested for durability. The durability test confirmed the connection between solid coating and substrate at all annealing temperatures. Thin films annealed at 600 °C revealed the best self-cleaning properties. The morphological analysis revealed snowflake shapes uniformly distributed over the substrate at 400 °C, and agglomeration improved as the annealing temperature increased. Structural analysis showed an increase in crystallinity with an increase in annealing temperature for both rutile and anatase phases. At three different temperatures, the chemical bond and the absorption band pattern followed the same path, although the peak intensity declined with temperature rise. Finally, the optical bandgap of the thin coated TiO 2 declined from 3.39 eV to 3.20 eV as the binding temperature increased from 400 to 800 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Digital Light Processing (DLP): 3D printing of polymer-based graphene oxide nanocomposites—Efficient antimicrobial material for biomedical devices

Bacterial infections are one of the major causes of surgical implant inefficiency and failure. Herein, we present a Nanocomposite (NC) produced by the addition of Poly(N-vinyl carbazole)-Graphene Oxide dispersion (PVK-GO) as a nanofiller to a commercial photopolymer acrylate resin and 3D printed as coatings via the Digital Light Processing technique. Characterization and bioassay results against Escherichia coli and Staphylococcus aureus confirmed the elevated thermomechanical properties and efficient antibacterial activity of the printed NC-based coatings. In conclusion, the present study demonstrates the fabrication and optimization of a PVK-GO-based NC and its potential utilization as a 3D-printable material for biomedical applications.

2D materials↗
DOE OSTI2024

Novel One-Step Production of Carbon-Coated Sn Nanoparticles for High-Capacity Anodes in Lithium-Ion Batteries

Lithium-ion batteries offer the highest energy density of any currently available portable energy storage technology. By using different anode materials, these batteries could have an even greater energy density. One material, tin, has a theoretical lithium capacity (994 mAh/g) over three-times higher than commercial carbon anode materials. Unfortunately, to achieve this high capacity, bulk tin undergoes a large volume expansion, and the material pulverizes during cycling, giving a rapid capacity fade. To mitigate this issue, tin must be scaled down to the nano-level to take advantage of unique micromechanics at the nanoscale. Synthesis techniques for Sn nanoparticle anodes are costly and overly complicated for commercial production. A novel one-step process for producing carbon-coated Sn nanoparticles via spark plasma erosion (SPE) shows great promise as a simple, inexpensive production method. The SPE method, characterization of the resulting particles, and their high-capacity reversible electrochemical performance as anodes are described. With only a 10% addition of these novel SPE carbon-coated Sn particles, one anode composition demonstrated a reversible capacity of ~460 mAh/g, achieving the theoretical capacity of that particular electrode formulation. These SPE carbon-coated Sn nanoparticles are drop-in ready for present commercial lithium-ion anode processing and would provide a ~10% increase in the total capacity of current commercial lithium-ion cells.

25 ENERGY STORAGE↗