SEARCH · Search NASA

Results for “Constraint Shapes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Search for low-mass resonances decaying into two jets and produced in association with a photon or a jet at √s = 13 TeV with the ATLAS detector

A search is performed for localized excesses in the low-mass dijet invariant mass distribution, targeting a hypothetical new particle decaying into two jets and produced in association with either a high transverse momentum photon or a jet. The search uses the full Run 2 data sample from LHC proton-proton collisions collected by the ATLAS experiment at a center-of-mass energy of 13 TeV during 2015–2018. Two variants of the search are presented for each type of initial-state radiation: one that makes no jet flavor requirements and one that requires both of the jets to have been identified as containing b-hadrons. No excess is observed relative to the Standard Model prediction, and the data are used to set upper limits on the production cross section for a benchmark Z' model and, separately, for generic, beyond the Standard Model scenarios which might produce a Gaussian-shaped contribution to dijet invariant mass distributions. The results extend the current constraints on dijet resonances to the mass range between 200 and 650 GeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1981

Numerical optimization of circulation control airfoils

A numerical procedure for optimizing circulation control airfoils, which consists of the coupling of an optimization scheme with a viscous potential flow analysis for blowing jet, is presented. The desired airfoil is defined by a combination of three baseline shapes (cambered ellipse, and cambered ellipse with drooped and spiralled trailing edges). The coefficients of these shapes are used as design variables in the optimization process. Under the constraints of lift augmentation and lift-to-drag ratios, the optimal airfoils are found to lie between those of cambered ellipse and the drooped trailing edge, towards the latter as the angle of attack increases. Results agree qualitatively with available experimental data.

Tai, T. C.↗

NASA NTRS1984

Numerical optimization of circulation control airfoil at high subsonic speed

A numerical procedure for optimizing the design of the circulation control airfoil for use at high subsonic speeds is presented. The procedure consists of an optimization scheme coupled with a viscous potential flow analysis for the blowing jet. The desired airfoil is defined by a combination of three baseline shapes (cambered ellipse and cambered ellipse with drooped and spiraled trailing edges). The coefficients of these shapes are used as design variables in the optimization process. Under the constraints of lift augmentation and lift-to-drag ratios, the airfoil, optimized at free-stream Mach 0.54 and alpha = -2 degrees can be characterized as a cambered ellipse with a drooped trailing edge. Experimental tests support the performance improvement predicted by numerical optimization.

Tai, T. C.↗

NASA NTRS1986

Trajectory shaping rendezvous guidance

The Space Station will bring a great increase in rendezvous traffic. Formerly, rendezvous has been expensive in terms of time and crew involvement. Multiple trajectory adjustments on separate orbits have been required to meet safety, lighting, and geometry requirements. This paper describes a new guidance technique in which the approach trajectory is shaped by a sequence of velocity increments in order to satisfy multiple constraints within a single orbit. The approach phase is planned before the mission, leaving a group of free parameters that are optimized by onboard guidance. Fuel penalties are typically a few percent, compared to unshaped Hohmann transfers, and total fuel costs can be less than those of more time-consuming ways of meeting the same requirements.

Klumpp, A. R.↗

NASA NTRS1986

Computer vision for robots; Proceedings of the Meeting, Cannes, France, December 2-6, 1985

The conference presents papers on segmentation techniques, three-dimensional recognition and representation, processing image sequences, and navigation and mobility. Particular attention is given to determining the pose of an object, adaptive least squares correlation with geometrical constraints, and the reliable formation of feature vectors for two-dimensional shape representation. Other topics include the real-time tracking of a target moving on a natural textured background, computer vision for the guidance of roving robots, and integrating sensory data for object recognition tasks.

Faugeras, O. D.↗

NASA NTRS1989

Power flows and Mechanical Intensities in structural finite element analysis

The identification of power flow paths in dynamically loaded structures is an important, but currently unavailable, capability for the finite element analyst. For this reason, methods for calculating power flows and mechanical intensities in finite element models are developed here. Formulations for calculating input and output powers, power flows, mechanical intensities, and power dissipations for beam, plate, and solid element types are derived. NASTRAN is used to calculate the required velocity, force, and stress results of an analysis, which a post-processor then uses to calculate power flow quantities. The SDRC I-deas Supertab module is used to view the final results. Test models include a simple truss and a beam-stiffened cantilever plate. Both test cases showed reasonable power flow fields over low to medium frequencies, with accurate power balances. Future work will include testing with more complex models, developing an interactive graphics program to view easily and efficiently the analysis results, applying shape optimization methods to the problem with power flow variables as design constraints, and adding the power flow capability to NASTRAN.

Hambric, Stephen A.↗

NASA NTRS1991

Aerodynamic calculations related to tethered sub-satellite experiments

The results are presented of four aerodynamic studies that were in support of a broader, preliminary inquiry concerning the potential use of downward-deployed tethered sub-satellites for in-flight aerothermodynamic research. There are a multitude of questions regarding the general tethered satellite concept and the present report addresses only a few of these. A method for estimating drag and local surface pressure and shear on orbiting or re-entereing bodies is described, and examples based on the planned TSS-2 (Tethered Satellite System) are given. The problem of pressure measurement are explored, taking into account thermal transpiration, lag time, and the disturbed flow field created by the satellite body. The performance of an aerodynamic stabilizer, a ring-tail design, is calculated and its influence on satellite motion is illustrated. A method for optimizing future satellite shapes for desired aerodynamic properties is transitional rarefied flow with given geometric constraints is proposed and examples are shown.

Potter, J. Leith↗

NASA NTRS2001

Simultaneous Aerodynamic and Structural Design Optimization (SASDO) for a 3-D Wing

The formulation and implementation of an optimization method called Simultaneous Aerodynamic and Structural Design Optimization (SASDO) is shown as an extension of the Simultaneous Aerodynamic Analysis and Design Optimization (SAADO) method. It is extended by the inclusion of structure element sizing parameters as design variables and Finite Element Method (FEM) analysis responses as constraints. The method aims to reduce the computational expense. incurred in performing shape and sizing optimization using state-of-the-art Computational Fluid Dynamics (CFD) flow analysis, FEM structural analysis and sensitivity analysis tools. SASDO is applied to a simple. isolated, 3-D wing in inviscid flow. Results show that the method finds the saine local optimum as a conventional optimization method with some reduction in the computational cost and without significant modifications; to the analysis tools.

Gumbert, Clyde R.↗

NASA NTRS2008

From Concept to Design: Progress on the J-2X Upper Stage Engine for the Ares Launch Vehicles

In accordance with national policy and NASA's Global Exploration Strategy, the Ares Projects Office is embarking on development of a new launch vehicle fleet to fulfill the national goals of replacing the space shuttle fleet, returning to the moon, and exploring farther destinations like Mars. These goals are shaped by the decision to retire the shuttle fleet by 2010, budgetary constraints, and the requirement to create a new fleet that is safer, more reliable, operationally more efficient than the shuttle fleet, and capable of supporting long-range exploration goals. The present architecture for the Constellation Program is the result of extensive trades during the Exploration Systems Architecture Study and subsequent refinement by the Ares Projects Office at Marshall Space Flight Center.

Byrd, Thomas↗

NASA NTRS2008

Structural Model Tuning Capability in an Object-Oriented Multidisciplinary Design, Analysis, and Optimization Tool

Updating the finite element model using measured data is a challenging problem in the area of structural dynamics. The model updating process requires not only satisfactory correlations between analytical and experimental results, but also the retention of dynamic properties of structures. Accurate rigid body dynamics are important for flight control system design and aeroelastic trim analysis. Minimizing the difference between analytical and experimental results is a type of optimization problem. In this research, a multidisciplinary design, analysis, and optimization [MDAO] tool is introduced to optimize the objective function and constraints such that the mass properties, the natural frequencies, and the mode shapes are matched to the target data as well as the mass matrix being orthogonalized.

Lung, Shun-fat↗

NASA NTRS2008

Structural Model Tuning Capability in an Object-Oriented Multidisciplinary Design, Analysis, and Optimization Tool

Updating the finite element model using measured data is a challenging problem in the area of structural dynamics. The model updating process requires not only satisfactory correlations between analytical and experimental results, but also the retention of dynamic properties of structures. Accurate rigid body dynamics are important for flight control system design and aeroelastic trim analysis. Minimizing the difference between analytical and experimental results is a type of optimization problem. In this research, a multidisciplinary design, analysis, and optimization (MDAO) tool is introduced to optimize the objective function and constraints such that the mass properties, the natural frequencies, and the mode shapes are matched to the target data as well as the mass matrix being orthogonalized.

Lung, Shun-fat↗

NASA NTRS1992

Search for deterministic pulse trends in gamma ray burst temporal profiles

Most cosmic gamma-ray burst temporal profiles appear to be comprised of several individual pulses, many of which overlap. It is advantageous to deconvolve the temporal structures into their constituent pulses, and thereby investigate the shape, intensity and temporal distributions of the pulses as a function of energy. Such fundamental pulse descriptors would provide constraints for theoretical modeling of the burst emission process, such as indications of source size, optical depth and geometry, as a function of time. We have developed a deconvolution algorithm which treats sequences of pulse shapes that change deterministically. The algorithm, a generalization of autoregressive techniques, has been applied to a few bright bursts observed by BATSE. Results indicate that, even within short intervals, constituent pulses are not self-similarly shaped, nor do pulse shapes evolve in a simple manner throughout a burst. Hence, the direction of our future work on pulse deconvolution will focus on analysis methods which allow pulse shape to vary.

Norris, J. P.↗

NASA NTRSDate not supplied

On-board Limb-based Shape Modeling for Small Body Navigation

Missions to small bodies within our solar system are becoming more frequent. Generally, shape models of the target body are required to perform proximity operations as demonstrated by the OSIRIS-REx, Hayabusa2, and Rosetta missions. However, these missions required image downlinking to create high-resolution models on the ground. In some missions, especially small-sats, there may be data downlink data constraints, resulting in the inability to provide the large number of images needed for high-resolution shape models. A solution to this is the ability to generate shape models on-board during the approach to the target or initial proximity surveying. Current work implements a limb-based shape model routine that is able to be executed on a Raspberry Pi 1, which is similar to the processing capability to the flight computer on OSIRIS-REx, and that does not require low phase angle geometries. Initial shape model results generated from Bennu approach (Nov 2-3, 2018) show that the limb-based shape model agrees well with a 75-cm SPC shape model generated after Preliminary Survey; Results are: min difference -7.047m, max difference 17.347m, mean 1.122m, and RMS 3.219m. Further scenarios are presented herein.

Limb-based↗

NASA NTRS2008

Characterization of Ni19.5Ti50.5Pd25Pt5 High-Temperature Shape Memory Alloy Springs and their Potential Application in Aeronautics

Shape memory alloys (SMAs) have been used as actuators in many different industries since the discovery of the shape memory effect, but the use of SMAs as actuation devices in aeronautics has been limited due to the temperature constraints of commercially available materials. Consequently, work is being done at NASA's Glenn Research Center to develop new SMAs capable of being used in high temperature environments. One of the more promising high-temperature shape memory alloys (HTSMAs) is Ni19.5Ti50.5Pd25Pt5. Recent work has shown that this material is capable of being used in operating environments of up to 250 C. This material has been shown to have very useful actuation capabilities, demonstrating repeatable strain recoveries up to 2.5% in the presence of an externally applied load. Based on these findings, further work has been initiated to explore potential applications and alternative forms of this alloy, such as springs. Thus, characterization of Ni19.5Ti50.5Pd25Pt5 springs, including their mechanical response and how variations in this response correlate to changes in geometric parameters, are discussed. The effects of loading history, or training, on spring behavior were also investigated. A comparison of the springs with wire actuators is made and the benefits of using one actuator form as opposed to the other discussed. These findings are used to discuss design considerations for a surge-control mechanism that could be used in the centrifugal compressor of a T-700 helicopter engine.

Stebner, Aaron↗

NASA NTRS1989

Launch packaging options for the photovoltaic power module cargo element

The National Aeronautics and Space Administration recently embarked on the Space Station Freedom program, which will utilize the Shuttle Orbiter for transportation to orbit. This task will be accomplished with a number of flights over several years. Each flight is unique in terms of the hardware that is manifested and the method by which it is integrated to form viable cargo elements. Work Package 4 is responsible for the electric power system for Space Station Freedom, and was delegated the authority to develop a photovoltaic (PV) power module cargo element. The PV power module consists of several unique assemblies. The first of these is the combined solar array/beta gimbal assembly. The remaining assemblies form the single combined integrated equipment assembly for each PV power module. These three combined assemblies are packaged into a launch cradle to form the PV power module cargo element, which is placed in the cargo bay of the Shuttle Orbiter for transportation to orbit. Various constraints determine the packaging options for the three PV power module combined assemblies. The size and shape of the combined assemblies in relation to the Shuttle Orbiter cargo bay dimensions and other manifested hardware are ultimately a factor in determining the acceptable packaging schemes for the PV power module cargo element. Several packaging options for the PV power module cargo element are presented. These options are discussed in terms of their impact on the overall flight hardware manifest as determined by the various constraints.

Hoberecht, Mark A.↗

DOE OSTI2025

A joint analysis of 3D clustering and galaxy × CMB-lensing cross-correlations with DESI DR1 galaxies

The spectroscopic data from DESI Data Release 1 (DR1) galaxies enables the analysis of 3D clustering by fitting galaxy power spectra and reconstructed correlation functions in redshift space. Given low measurements of the amplitude of structure from cosmic shear at z ∼ 1, redshift space distortions (RSD) + Baryon Acoustic Oscillation (BAO) signals from DESI galaxies combined with weak lensing can break degeneracies and provide a tight alternative constraint on the z ∼ 1 amplitude of structure. In this paper we perform joint analyses that combine full-shape + post-reconstruction information from the DESI DR1 BGS and LRG samples along with angular cross-correlations with Planck PR4 and ACT DR6 CMB lensing maps. We show that adding galaxy-lensing cross-correlations tightens clustering amplitude constraints, improving σ 8 uncertainties by 30% over RSD+BAO alone. We also include angular galaxy-galaxy and galaxy-lensing spectra using photometric samples from the DESI Legacy Survey to further improve constraints. Our headline results are σ 8 = 0.803 ± 0.017, Ω m = 0.3037 ± 0.0069, and S 8 = 0.808 ± 0.017. Given DESI's preference for higher σ 8 compared to lower values from BOSS, we perform a catalog-level comparison of LRG samples from both surveys. We test sensitivity to dark energy assumptions by relaxing our ΛCDM prior and allowing for evolving dark energy via the w 0 - w a parameterization. We find our S 8 constraints to be relatively unchanged despite a 3.5σ tension with the cosmological constant model when combining with the Union3 supernova likelihood. Finally we test general relativity (GR) by allowing the gravitational slip parameter (γ) to vary, and find γ = 1.17 ± 0.11 in mild (∼ 1.5σ) tension with the GR value of 1.0.

cosmological parameters from LSS↗

DOE OSTI2026

First experimental realization of robust negative triangularity plasma control in a spherical tokamak

In this work, we present the experimental realization of a plasma with a steady negative triangularity (NT) in a spherical tokamak (MAST-U) for the first time. An average triangularity of –0.1 was maintained for 100 ms in a double-null plasma with a plasma current of 600 kA, a neutral beam injected power of 3.2 MW, a normalized β of 2, and an elongation of 2 on the MAST-U spherical tokamak. Despite many constraints, this was made possible due to the development of a dedicated plasma shape control scheme and the validation and assessment of magnetic shape controllers in simulations. Furthermore, this effort lays the foundation for physics exploitation of the NT plasma in a spherical tokamak.

negative triangularity↗

NASA NTRS1990

Dynamic Analysis and Control of Lightweight Manipulators with Flexible Parallel Link Mechanisms

The objective is the theoretical analysis and the experimental verification of dynamics and control of a two link flexible manipulator with a flexible parallel link mechanism. Nonlinear equations of motion of the lightweight manipulator are derived by the Lagrangian method in symbolic form to better understand the structure of the dynamic model. The resulting equation of motion have a structure which is useful to reduce the number of terms calculated, to check correctness, or to extend the model to higher order. A manipulator with a flexible parallel link mechanism is a constrained dynamic system whose equations are sensitive to numerical integration error. This constrained system is solved using singular value decomposition of the constraint Jacobian matrix. Elastic motion is expressed by the assumed mode method. Mode shape functions of each link are chosen using the load interfaced component mode synthesis. The discrepancies between the analytical model and the experiment are explained using a simplified and a detailed finite element model.

Lee, Jeh Won↗