Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIPOLE ANTENNA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

An 86-106 GHz quasi-integrated low noise Schottky receiver

An integrated planar receiver was developed and tested over the 82-112 GHz bandwidth. The quasi-integrated antenna used in the receiver has a high gain, a high Gaussian coupling efficiency, and a wide bandwidth. The novel mixer design consists of a planar GaAs Schottky diode placed at the feed of a dipole-probe suspended inside an integrated horn antenna. The diode uses an etched surface channel and a planar air bridge for reduced parasitic capacitance. At 92 GHz, the room-temperature antenna-mixer exhibits a double sideband conversion loss and noise temperature of 5.5 +/- 0.5 dB and 770 K +/- 50 K, respectively. The measured DSB conversion loss and noise temperature over a 20 GHz bandwidth (86 GHz-106 GHz) remain less than 6.2 dB +/- 0.5 dB and 1000 K +/- 50 K, respectively. The low cost of fabrication and simplicity of the design makes it ideal for millimeter- and submillimeter-wave receivers.

Ali-Ahmad, Walid Y.↗
NASA NTRS1975

Study of the performance of antennas in magnetized plasmas

The antenna studies were performed in a large magnetized plasma source, a schematic drawing of which is shown. The plasma diagnostics consist of a 70 GHz (4 mm) microwave interferometer for density measurements and of various Langmuir probes for spatially resolved measurements of t sub e, n sub e and the shape of the electron distribution function. All diagnostic data are time-resolved by sample-and-hold techniques so as to yield information about the plasma build-up, the steady-state discharge, and the plasma decay in the afterglow. Whistler waves are excited and detected with various antennas which are inserted into the center of the plasma column through one axial and two orthogonal radial ports. The antennas were tested for their proper dipole response and then calibrated in a known field geometry in air. For the electric dipole, a parallel plate capacitor field was used; the magnetic loop is calibrated in the near-zone field of a long linear conductor of known radio frequency current distribution. Results are presented and discussed.

Stenzel, R. L.↗
NASA NTRS1978

Space plasma laboratory - Experiment in simulated ionospheric plasma

Several experiments with simulated ionospheric plasma were performed in the Johnson Space Center's large (17 m diameter x 27 m height) vacuum chamber. Two of these, the RF discharge and the electron-beam plasma discharge, are described here. The RF experiment involved measurement of the loading on a 5 m dipole and a 5 m loop antenna caused by the presence of a plasma. The results indicate that when the RF frequency is near the electron gyro frequency a self-sustained plasma discharge is set up and the real part of the complex antenna impedance increases. The beam-plasma experiment was carried out to study a discharge produced by an electron beam with an energy of about 1 keV when the electron beam was injected parallel to the ambient magnetic field. As the beam current was raised to a critical level, a spontaneous transition occurred whereby a luminous halo was formed around the electron beam indicating a sustained discharge.

Konradi, A.↗
NASA NTRS1980

Solar power satellite offshore rectenna study

Offshore rectennas are feasible and cost competitive with land rectennas but the type of rectenna suitable for offshore use is quite different from that specified in the present reference system. A nonground plane design minimizes the weight and greatly reduces the number of costly support towers. This perferred design is an antenna array consisting of individually encapsulated dipoles with reflectors or tagis supported on feed wires. Such a 5 GW rectenna could be built at a 50 m water depth site to withstand hurricane, winter storm, and icing conditions for a one time cost of $5.7 billion. Subsequent units would be about 1.3 less expensive. More benign and more shallow water sites would result in substantially lower costs. The major advantage of an offshore rectenna is the removal of microwave radiation from populated areas.

Source record↗
NASA NTRS1980

Solar power satellite offshore rectenna study

It was found that an offshore rectenna is feasible and cost competitive with land rectennas but that the type of rectenna which is suitable for offshore use is quite different from that specified in the present reference system. The result is a nonground plane design which minimizes the weight and greatly reduces the number of costly support towers. This preferred design is an antenna array consisting of individually encapsulated dipoles with reflectors supported on feed wires. Such a 5 GW rectenna could be built at a 50 m water depth site to withstand hurricane and icing conditions for a one time cost of 5.7 billion dollars. Subsequent units would be about 1/3 less expensive. The east coast site chosen for this study represents an extreme case of severe environmental conditions. More benign and more shallow water sites would result in lower costs. Secondary uses such as mariculture appear practical with only minor impact on the rectenna design. The potential advantages of an offshore rectenna, such as no land requirements, removal of microwave radiation from populated areas and minimal impact on the local geopolitics argue strongly that further investigation of the offshore rectenna should be vigorously pursued.

Source record↗
NASA NTRS1983

Polarized-interferometer feasibility study

The feasibility of using a polarized-interferometer system as a rendezvous and docking sensor for two cooperating spacecraft was studied. The polarized interferometer is a radio frequency system for long range, real time determination of relative position and attitude. Range is determined by round trip signal timing. Direction is determined by radio interferometry. Relative roll is determined from signal polarization. Each spacecraft is equipped with a transponder and an antenna array. The antenna arrays consist of four crossed dipoles that can transmit or receive either circularly or linearly polarized signals. The active spacecraft is equipped with a sophisticated transponder and makes all measurements. The transponder on the passive spacecraft is a relatively simple repeater. An initialization algorithm is developed to estimate position and attitude without any a priori information. A tracking algorithm based upon minimum variance linear estimators is also developed. Techniques to simplify the transponder on the passive spacecraft are investigated and a suitable configuration is determined. A multiple carrier CW signal format is selected. The dependence of range accuracy and ambiguity resolution error probability are derived and used to design a candidate system. The validity of the design and the feasibility of the polarized interferometer concept are verified by simulation.

Raab, F. H.↗
NASA NTRS2007

Antenna for Measuring Electric Fields Within the Inner Heliosphere

A document discusses concepts for the design of an antenna to be deployed from a spacecraft for measuring the ambient electric field associated with plasma waves at a location within 3 solar radii from the solar photosphere. The antenna must be long enough to extend beyond the photoelectron and plasma sheaths of the spacecraft (expected to be of the order of meters thick) and to enable measurements at frequencies from 20 Hz to 10 MHz without contamination by spacecraft electric-field noise. The antenna must, therefore, extend beyond the thermal protection system (TPS) of the main body of the spacecraft and must withstand solar heating to a temperature as high as 2,000 C while not conducting excessive heat to the interior of the spacecraft. The TPS would be conical and its axis would be pointed toward the Sun. The antenna would include monopole halves of dipoles that would be deployed from within the shadow of the TPS. The outer potion of each monopole would be composed of a carbon-carbon (C-C) composite surface exposed to direct sunlight (hot side) and a C-C side in shadow (cold side) with yttria-stabilized zirconia spacers in-between. The hot side cannot view the spacecraft bus, while the cold side can. The booms also can be tilted to minimize heat input to spacecraft bus. This design allows one to reduce heat input to the spacecraft bus to acceptable levels.

Sittler, Edward Charles↗
NASA NTRS1984

Status of the Jicamarca radar

The capabilities of the large 50-MHz radar at Jicamarca for mesosphere-stratosphere-troposphere MST observations were discussed in some detail. Hence this description will be quite brief and will concentrate on recent improvements in the facility. The radar is located about 20 km from Lima, Peru. It is well shielded by surrounding mountains, and most of the ground clutter is restricted to ranges of 15 km or less. The antenna consists of 18,432 half-wave dipoles (9216 crossed pairs) covering an area of 290 m by 290 m and divided up into 64 independent modules which can be individually phased and/or used as separate antennas in any way desired. The whole array can be steered about 3 degrees from the on-axis position (the limit is the beam width of the individual modules, which cannot be steered), and any polarization can be arranged. Even with this limited steerability it is straightforward to determine vector wind velocities by pointing segments of the antenna in different directions. The radar can also be used as in interferometer.

Farley, T.↗
NASA NTRS1985

Measurements of distributed polarized radio sources from spinning spacecraft - Effect of a tilted axial antenna ISEE-3 application and results

An analysis is presented of the system response of a satellite receiver-antenna system to locate a radio source when the satellite is tilted on its axis. The satellite is spin stabilized but experiences a tilt due to either a mechanical misalignment or a shift in the electrical axis caused by parasitic currents in other spacecraft structures. The shorter the antenna, the more significant the effects. Numerical techniques are developed for obtaining the Stokes parameters and the angular parameters of a uniform conical source sensed by a linear antenna in order to derive the average power response of a synthesized dipole to a point on a distributed polarized source. Relative gains are calculated along the antenna at different angles to the source. The techniques are applied to sample ISEE-3 satellite data for Type III solar radio bursts which were sensed by an axial and an equatorial antenna. The two antennas permit localization of the source and quantification of the polarization and angular extent of the source. The resulting high precision in calculations of all three source parameters commends use of the model in analyses of data from the planned ULYSSES mission.

Fainberg, J.↗
NASA NTRS1981

General aviation aircraft antennas for the global positioning system

Several antenna designs that utilize the NAVSTAR Global Positioning System in a low-cost system for general aviation aircraft were evaluated. Experimental investigations were made of crossed-dipoles, various types of crossed-slots, and microstrip antennas with modifications to improve their coverage. Principal plane radiation patterns for several of these antennas were measured on a one-seventh scale model of a Gates Lear Jet.

Gilreath, M. C.↗
NASA NTRS1975

MLS airborne antenna research

The geometrical theory of diffraction was used to analyze the elevation plane pattern of on-aircraft antennas. The radiation patterns for basic elements (infinitesimal dipole, circumferential and axial slot) mounted on fuselage of various aircrafts with or without radome included were calculated and compared well with experimental results. Error phase plots were also presented. The effects of radiation patterns and error phase plots on the polarization selection for the MLS airborne antenna are discussed.

Yu, C. L.↗
NASA NTRS1986

High-gain backup antenna design for Pioneer Venus Orbiter spacecraft

The development and performance is described of a high-gain antenna designed to serve on the Pioneer Venus Orbiter spacecraft as a backup to the principal high-gain antenna unit in the unlikely event the mechanically despun antenna mechanism malfunctioned. The final design, a center-fed standing wave array of six sleeve dipoles enclosed in a fiber glass radome, performed successfully, as did all the antennas, on the Pioneer Orbiter spacecraft which was launched on May 20, 1978, as part of the Pioneer Venus mission. Photographs of experimental models giving details of design and construction are included, as well as graphs showing measured pattern and impedance matching characteristics of the subject antenna.

Glaser, J. I.↗
NASA NTRS2005

Deployable Wide-Aperture Array Antennas

Inexpensive, lightweight array antennas on flexible substrates are under development to satisfy a need for large-aperture antennas that can be stored compactly during transport and deployed to full size in the field. Conceived for use aboard spacecraft, antennas of this type also have potential terrestrial uses . most likely, as means to extend the ranges of cellular telephones in rural settings. Several simple deployment mechanisms are envisioned. One example is shown in the figure, where the deployment mechanism, a springlike material contained in a sleeve around the perimeter of a flexible membrane, is based on a common automobile window shade. The array can be formed of antenna elements that are printed on small sections of semi-flexible laminates, or preferably, elements that are constructed of conducting fabric. Likewise, a distribution network connecting the elements can be created from conventional technologies such as lightweight, flexible coaxial cable and a surface mount power divider, or preferably, from elements formed from conductive fabrics. Conventional technologies may be stitched onto a supporting flexible membrane or contained within pockets that are stitched onto a flexible membrane. Components created from conductive fabrics may be attached by stitching conductive strips to a nonconductive membrane, embroidering conductive threads into a nonconductive membrane, or weaving predetermined patterns directly into the membrane. The deployable antenna may comprise multiple types of antenna elements. For example, thin profile antenna elements above a ground plane, both attached to the supporting flexible membrane, can be used to create a unidirectional boresight radiation pattern. Or, antenna elements without a ground plane, such as bow-tie dipoles, can be attached to the membrane to create a bidirectional array such as that shown in the figure. For either type of antenna element, the dual configuration, i.e., elements formed of slots in a conductive membrane, can also be used. Finally, wide bandwidth antennas or arrays can be formed in which the principal direction of radiation is in the plane of the membrane. For this embodiment, the set of elements on the membrane is arranged to form one or more traveling wave antennas. In this case, a nonconductive form of the perimeter springlike material is required to provide the deploying force.

Fink, Patrick W.↗
NASA NTRS1995

Electromagnetic compatibility and the all-electric airplane

NASA is studying the feasibility of installing 'all-electric' controls in future commercial aircraft, replacing the current hydraulic and pneumatic systems. Planes utilizing such equipment should weigh less and be cheaper to maintain, but might also be susceptible to interference from undesired external electromagnetic fields. Possible sources of these extraneous signals include radio and television broadcasters, two-way communications stations, and radar installations of all kinds. One way to reduce the hazard would be to use fiber-optic cables to carry signals from the cockpit to the various points of use, a concept known as 'fly-by-light' or FBL. However, electrical circuits (PBW, or 'power-by-wire') would still be required at both ends of the cables to perform control functions, so the possibility of harmful interference would remain. Computer models for two different antennas were created in order to find the magnitude of the electric fields which would be generated in the airspace around them while in the transmit mode. The first antenna was a horizontal 'rhombic' used by the Voice of America (VOA) for long-distance short-wave broadcasting. The second antenna was a multi-element 'log-periodic dipole array' (LPDA) of a type often used for two-way radio communications. For each case, a specified amount of power was applied in the computer model, and the resulting electric field intensity was predicted at a variety of locations surrounding the antenna. This information will then be used to calculate the levels of interference which could occur inside an airplane flying in the vicinity of these radiation emitters.

Christman, Al↗
NASA NTRS2006

MARSIS antenna flight deployment anomaly and resolution

This paper summarizes the resolution of an in flight anomaly that occurred during the deployment of the first of three MARSIS antenna booms. Characteristics of this deployment are described, along with a correlation to finite element models and measured spacecraft inertias, which allowed the intermediate state of the boom to be accurately determined. Based on this information, a spacecraft maneuver was performed that warmed the stalled hinge and led to the first boom successfully locking into its designed geometry. The confirmed partially deployed boom shape was then used to develop a thermal model of the stalled hinge both in its initial solar attitude and during the successful spacecraft maneuver. Results from the hinge thermal model and component level testing were evaluated in order to determine the root cause of the anomaly and the probability of its recurrence on subsequent deployments. These conclusions were then utilized in planning mitigating actions that were implemented during the remaining two boom deployments. Final flight data are presented for both dipole booms indicating a correctly deployed and healthy antenna. The monopole boom deployment was detected but the final state of the boom is unknown.

Mars↗
NASA NTRS1971

Analysis and design of antennas for air traffic collision avoidance systems.

The analysis and design procedure of an antenna for a CW Doppler radar system being developed for pilot warning of midair collision hazards is presented. The antenna consists of two vertical arrays of half-wavelength dipoles mounted near a circular conducting cylinder. Each vertical array is composed of three vertical dipoles. Each array provides relatively uniform illumination (2.3 dB) in the forward 180-deg angular segment of the horizontal plane and approximately plus or minus 10 to 15 deg coverage in the vertical plane. The antenna could be used in a two-mode operation, either in a standard monopulse radar system (sum and difference amplitude patterns) or in a system where amplitude and phase are the measurable quantities.

Balanis, C. A.↗
NASA NTRS1981

Antennas in matter: Fundamentals, theory, and applications

The volume provides an introduction to antennas and probes embedded within or near material bodies such as the earth, the ocean, or a living organism. After a fundamental analysis of insulated and bare antennas, an advanced treatment of antennas in various media is presented, including a detailed study of the electromagnetic equations in homogeneous isotropic media, the complete theory of the bare dipole in a general medium, and a rigorous analysis of the insulated antenna as well as bare and insulated loop antennas. Finally, experimental models and measuring techniques related to antennas and probes in a general dissipative or dielectric medium are examined.

King, R. W. P.↗