Search NASA⌕ Search

SEARCH · Search NASA

Results for “DRAG REDUCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Skin friction measurements following manipulation of a turbulent boundary layer

Results are presented from three experiments in which direct, local measurements of the skin friction reduction due to flat-plate turbulence manipulators for overall viscous drag reduction were obtained. The results suggest that only a very small overall net drag reduction will be possible for such devices at moderate momentum thickness-derived Reynolds number values, since maximum skin friction drag is neither large nor sustained.

Nguyen, V. D.↗
NASA NTRS1986

Natural laminar flow nacelle for transport aircraft

The potential of laminar flow nacelles for reducing installed engine/nacelle drag was studied. The purpose was twofold: to experimentally verify a method for designing laminar flow nacelles and to determine the effect of installation on the extent of laminar flow on the nacelle and on the nacelle pressure distributions. The results of the isolated nacelle tests illustrated that laminar flow could be maintained over the desired length. Installing the nacelles on wing/pylon did not alter the extent of laminar flow occurring on the nacelles. The results illustrated that a significant drag reduction was achieved with this laminar flow design. Further drag reduction could be obtained with proper nacelle location and pylon contouring.

Lamb, Milton↗
NASA NTRS1975

Rotorcraft low-speed download drag definition and its reduction

Download drag for rotorcraft in hover and low-speed flight is a burden which significantly affects useful load, fuel, and payload. Reduction of the burden will enhance these aspects of rotorcraft and complement the forthcoming improvements in isolated rotor performance. Analyses and experimental data are available, though fragmentary, regarding gross drag, thrust recovery, and other characteristics which can be utilized to define interim rotorcraft design changes to reduce the burden. Eventually the experimental data and a comprehensive combination of rotor, rotor-wake, and potential-flow analyses can evolve to reduce the burden to an absolute minimum.

Wilson, J. C.↗
NASA NTRS1992

Development of a hydrogen external burning flight test experiment on the NASA Dryden SR-71A aircraft

A captive-carry flight test experiment of the transonic external burning concept using gaseous hydrogen fuel has ben proposed for the SR-71A flight research test bed aircraft at the NASA Dryden Flight Research Facility, Edwards, California. This program will be the first large-scale, near-field flight test investigation of this base drag reduction technique at Mach numbers up to 3. Low-speed base drag reduction for supersonic and hypersonic flight vehicles is important in reducing vehicle drag and improving nozzle efficiency. Flight data will be correlated with a concurrent wind tunnel ground test of a similar test apparatus to confirm geometry and component performance scalability predictions and to investigate design parametrics under actual flight conditions. This paper describes the problem of transonic base drag for supersonic and hypersonic aircraft, a planned flight research program to address this problem, the test bed aircraft, and the flight experiment apparatus.

Hicks, John W.↗
NASA NTRS1951

Aerodynamic Characteristics of a Flying-Boat Hull Having a Length-Beam Ratio of 15, TED No. NACA 2206

An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of a flying-boat hull of a length-beam ratio of 15 in the presence of a wing. The investigation was an extension of previous tests made on hulls of length-beam ratios of 6, 9, and 12; these hulls were designed to have approximately the same hydrodynamic performance with respect to spray and resistance characteristics. Comparison with the previous investigation at lower length-beam ratios indicated a reduction in minimum drag coefficients of 0.0006 (10 peroent)with fixed transition when the length-beam ratio was extended from 12 to 15. As with the hulls of lower length-beam ratio, the drag reduction with a length-beam ratio of 15 occurred throughout the range of angle of attack tested and the angle of attack for minimum drag was in the range from 2deg to 3deg. Increasing the length-beam ratio from 12 to 15 reduced the hull longitudinal instability by an mount corresponding to an aerodynamic-center shift of about 1/2 percent of the mean aerodynamic chord of the hypothetical flying boat. At an angle of attack of 2deg, the value of the variation of yawing-moment coefficient with angle of yaw for a length-beam ratio of 15 was 0.00144, which was 0.00007 larger than the value for a length-beam ratio of 12.

Riebe, John M.↗
NASA NTRS1984

Performance of large-eddy breakup devices at post-transitional Reynolds numbers

Large-eddy alteration techniques were used to modify the drag characteristics of the turbulent boundary layer. Local skin-friction coefficients were measured for single and multi-element arrays of thin plates suspended in a fully turbulent, flat plate, boundary layer at R(theta) = 3,000. Effects of these devices were measured more than 300 boundary-layer thicknesses downstream to R(theta) = 17,000. It was found that although most of the devices reduced the local skin friction immediately downstream, this reduced skin-friction region persisted for only 100-120 delta-0, after which a rapid rise in skin-friction coefficient occurred, often exceeding flat plate values. Net drag reductions were obtained only for tandem configurations and these reductions were sensitive to device spacing and height. The maximum net drag reduction reported was approximately 7 percent with a device spacing of 10 delta-0 at a height of 0.8 delta-0.

Anders, J. B.↗
NASA NTRS1975

Cost consideration for aircraft configuration changes, 1

The costs of improvements in aircraft drag reduction design changes are outlined in the context of production decisions. A drag reduction design with increased airframe weight requires cost increases for direct labor, overhead and direct expenses, plus general and administrative expenses.

Tumlinson, R. R.↗
NASA NTRS1986

Flight research on natural laminar flow

Five decades of flight experiences with natural laminar flow (NLF) have provided a basis of understanding how this technology can be used for reduction of viscous drag on modern practical aircraft. The effects of cruise unit Reynolds number on NLF achievability and maintainability; compressibility effects on Tollmein-Schlichting growth; flight experiment on the Cessna Citation III business jet; flight instrumentation on Lear 28/29; OV-I NLF engine nacelle experiments; and viscous drag reduction are examined.

Holmes, B. J.↗
NASA NTRS1989

Effects of contamination on riblet performance

Thin-element polymeric film riblet surfacing materials previously shown to behave similarly to v-groove riblets in the reduction of aerodynamic drag have been tested to ascertain the effects of groove contamination. Three different levels of contamination were simulated for each of two kinds of contamination. Such contaminants as oil drops and condensates have no significant effect on drag reduction. Atmospheric particulates may, however, degrade riblet performance.

Lazos, Barry S.↗
NASA NTRS1991

Laminar-Separation Sensor

Reduction of viscous drag on airplanes explores limits of practical applications of natural laminar flow. Wind-tunnel and flight tests conducted to explore abilities of hot-film sensors to identify separation of laminar flow as principal mode of amplification of instability leading to transition from laminar to turbulent flow. Two different laminar-separation-sensor configurations developed and used to detect boundary-layer transitions. Results show hot-film laminar-separation-sensor technique viable means for detecting existence of transition as well as for indicating reversed flow in laminar-separation bubble. Refinement of sensor configurations provides tools necessary to explore, in all speed regimes, practical limits of laminar-flow applications and viscous-drag-reduction technology.

Manuel, G. S.↗
NASA NTRS1999

Supersonic Aerodynamic Design Improvements of an Arrow-Wing HSCT Configuration Using Nonlinear Point Design Methods

This paper is a discussion of the supersonic nonlinear point design optimization efforts at McDonnell Douglas Aerospace under the High-Speed Research (HSR) program. The baseline for these optimization efforts has been the M2.4-7A configuration which represents an arrow-wing technology for the High-Speed Civil Transport (HSCT). Optimization work on this configuration began in early 1994 and continued into 1996. Initial work focused on optimization of the wing camber and twist on a wing/body configuration and reductions of 3.5 drag counts (Euler) were realized. The next phase of the optimization effort included fuselage camber along with the wing and a drag reduction of 5.0 counts was achieved. Including the effects of the nacelles and diverters into the optimization problem became the next focus where a reduction of 6.6 counts (Euler W/B/N/D) was eventually realized. The final two phases of the effort included a large set of constraints designed to make the final optimized configuration more realistic and they were successful albeit with a loss of performance.

Unger, Eric R.↗
NASA NTRS1989

An Experimental Investigation of Helicopter Rotor Hub Fairing Drag Characteristics

A study was done in the NASA 14- by 22-Foot Wind Tunnel at Langley Research Center on the parasite drag of different helicopter rotor hub fairings and pylons. Parametric studies of hub-fairing camber and diameter were conducted. The effect of hub fairing/pylon clearance on hub fairing/pylon mutual interference drag was examined in detail. Force and moment data are presented in tabular and graphical forms. The results indicate that hub fairings with a circular-arc upper surface and a flat lower surface yield maximum hub drag reduction; and clearance between the hub fairing and pylon induces high mutual-interference drag and diminishes the drag-reduction benefit obtained using a hub fairing with a flat lower surface. Test data show that symmetrical hub fairings with circular-arc surfaces generate 74 percent more interference drag than do cambered hub fairings with flat lower surfaces, at moderate negative angle of attack.

Sung, D. Y.↗
NASA NTRS1957

A Theoretical Investigation of the Drag of Generalized Aircraft Configurations in Supersonic Flow

It seems possible that, in supersonic flight, unconventional arrangements of wings and bodies may offer advantages in the form of drag reduction. It is the purpose of this report to consider the methods for determining the pressure drag for such unconventional configurations, and to consider a few of the possibilities for drag reduction in highly idealized aircraft. The idealized aircraft are defined by distributions of lift and volume in three-dimensional space, and Hayes' method of drag evaluation, which is well adapted to such problems, is the fundamental tool employed. Other methods of drag evaluation are considered also wherever they appear to offer amplifications. The basic singularities such as sources, dipoles, lifting elements and volume elements are discussed, and some of the useful inter-relations between these elements are presented. Hayes' method of drag evaluation is derived in detail starting with the general momentum theorem. In going from planar systems to spatial systems certain new problems arise. For example, interference between lift and thickness distributions generally appears, and such effects are used to explain the difference between the non-zero wave drag of Sears-Haack bodies and the zero wave drag of Ferrari's ring wing plus central body. Another new feature of the spatial systems is that optimum configurations generally are not unique, there being an infinite family of lift or thickness distributions producing the same minimum drag. However it is shown that all members of an optimum family produce the same flow field in a certain region external to the singularity distribution. Other results of the study indicate that certain spatial distributions may produce materially less wave drag and vortex drag than comparable planar systems. It is not at all certain that such advantages can be realized in practical aircraft designs, but further investigation seems to be warranted.

Graham, E. W.↗
NASA NTRS2004

Using High Resolution Design Spaces for Aerodynamic Shape Optimization Under Uncertainty

This paper explains why high resolution design spaces encourage traditional airfoil optimization algorithms to generate noisy shape modifications, which lead to inaccurate linear predictions of aerodynamic coefficients and potential failure of descent methods. By using auxiliary drag constraints for a simultaneous drag reduction at all design points and the least shape distortion to achieve the targeted drag reduction, an improved algorithm generates relatively smooth optimal airfoils with no severe off-design performance degradation over a range of flight conditions, in high resolution design spaces parameterized by cubic B-spline functions. Simulation results using FUN2D in Euler flows are included to show the capability of the robust aerodynamic shape optimization method over a range of flight conditions.

Li, Wu↗
NASA NTRS2017

A Sweeping Jet Application on a High Reynolds Number Semispan Supercritical Wing Configuration

The FAST-MAC circulation control model was modified to test an array of unsteady sweeping-jet actuators at realistic flight Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center. Two types of sweeping jet actuators were fabricated using rapid prototype techniques, and directed over a 15% chord simple-hinged flap. The model was configured for low-speed high-lift testing with flap deflections of 30° and 60°, and a transonic cruise configuration with a 0° flap deflection. For the 30° flap high-lift configuration, the sweeping jets achieved comparable lift performance in the separation control regime, while reducing the mass flow by 54% as compared to steady blowing. However, the sweeping jets were not effective for the 60° flap. For the transonic cruise configuration, the sweeping jets reduced the drag by 3.3% at an off design condition. The drag reduction for the design lift coefficient for the sweeping jets provided only half the drag reduction shown for the steady blowing case (6.5%), but accomplished this with a 74% reduction in mass flow.

Gregory S Jones↗
NASA NTRS2017

A Sweeping Jet Application on a High Reynolds Number Semispan Supercritical Wing Configuration

The FAST-MAC circulation control model was modified to test an array of unsteady sweeping-jet actuators at realistic flight Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center. Two types of sweeping jet actuators were fabricated using rapid prototype techniques, and directed over a 15% chord simple-hinged flap. The model was configured for low-speed high-lift testing with flap deflections of 30 deg and 60 deg, and a transonic cruise configuration having a 0 deg flap deflection. For the 30 deg flap high-lift configuration, the sweeping jets achieved comparable lift performance in the separation control regime, while reducing the mass flow by 54% as compared to steady blowing. The sweeping jets however were not effective for the 60 deg flap. For the transonic cruise configuration, the sweeping jets reduced the drag by 3.3% at an off-design condition. The drag reduction for the design lift coefficient for the sweeping jets offer is only half the drag reduction shown for the steady blowing case (6.5%), but accomplished this with a 74% reduction in mass flow.

Jones, Gregory S.↗
NASA NTRS1976

Re-examination of compliant wall experiments in air with water substrates

A possible alternative explanation is proposed for compliant wall drag reductions measured in previous investigations. Standing waves were observed to form on the surfaces of compliant wall models in air with water substrates as the freestream velocity was increased from 15 to 30 m/s. These waves resembled sine waves with half of the wave protruding over the upstream portion of the model and the other half being recessed over the downstream end of the model. These data coupled with results of recent drag reduction experiments suggest that standing waves could have caused a shift in the model center of gravity creating a bending moment that was interpreted as a reduction in the skin friction drag.

Hefner, J. N.↗
NASA NTRS1986

Drag reducing outer-layer devices in rough wall turbulent boundary layers

The ability of outer-layer devices to reduce wall shear stress over a substantial streamwise distance in rough-wall turbulent boundary layers has been studied experimentally. The devices examined are a pair of thin flat ribbons placed in tandem as well as those having symmetric airfoil sections. The wall conditions examined are smooth, d- and k-type transverse-groove and sandgrain roughnesses. The wall drag is found to be reduced from the respective normal levels in all rough walls. All k-type rough walls exhibit a similar level of relative wall drag reduction which is also smaller than that in a smooth-wall. The d-type rough walls exhibit a transitional behaviour - the relative wall drag reduction drops from the smooth wall level to that of the k-type roughness with increasing roughness Reynolds number. However, the absolute reductions in the local wall shear stress are similar in both the rough and smooth walls. On the other hand, the relative reductions are lower in the rough walls because of a higher reference drag which is caused by the unique presence of a pressure component on which the devices are not as effective.

Bandyopadhyay, P. R.↗