The 100-kW hingeless metal wind turbine blade design, analysis and fabrication considerations
Explore the source record for details and available documents.
Donham, R. E.↗
SEARCH · Search NASA
Results for “Design Analysis”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Analysis, design, fabrication and testing of the mini-Brayton rotating unit (Mini-BRU). Volume 1: Text and tables
A 500 to 2100 watt power output Mini-Brayton Rotating Unit (Mini-BRU)was analyzed, designed, fabricated and tested. Performance and test data for the various components is included. Components tested include the 2.12 in. diameter compressor, the 2.86 in. diameter turbine, the Rice alternator and the cantilevered foil-type journal and thrust bearings. Also included are results on the fabrication of a C-103 turbine plenum/nozzle assembly and on offgassing of the organic materials in the alternator stator.
Dobler, F. X.↗
Analysis, design, fabrication and testing of the Mini-Brayton rotating unit (MINI-BRU). Volume 2: Figures and drawings
This volume contains the figures and drawings reference in Volume 1.
Dobler, F. X.↗
Digital controller design: Analysis of the annular suspension pointing system
The Annular Suspension and Pointing System (ASPS) is a payload auxiliary pointing device of the Space Shuttle. The ASPS is comprised of two major subassemblies, a vernier and a coarse pointing subsystem. The experiment is attached to a mounting plate/rim combination which is suspended on magnetic bearing/actuators (MBA) strategically located about the rim. Fine pointing is achieved by gimballing the plate/rim within the MBA gaps. Control about the experiment line-of-sight is obtained through the use of a non-contacting rim drive and positioning torquer. All sensors used to close the servo loops on the vernier system are noncontacting elements. Therefore, the experiment is a free-flyer constrained only by the magnetic forces generated by the control loops.
Kuo, B. C.↗
Off-design analysis of a gas turbine powerplant augmented by steam injection using various fuels
Results are compared using coal derived low and intermediate heating valve fuel gases and a conventional distillate. The results indicate that steam injection provides substantial increases in both power and efficiency within the available compressor surge margin. The results also indicate that these performance gains are relatively insensitive as to the type of fuel. Also, in a cogeneration application, steam injection could provide some degree of flexibility by varying the split between power and process steam.
Stochl, R. J.↗
Design, analysis, and test verification of advanced encapsulation system
Procurement of 4 in x 4 in polycrystalline solar cells were proceeded with some delays. A total of 1200 cells were procured for use in both the verification testing and qualification testing. Additional thermal structural analyses were run and the data are presented. An outline of the verification testing is included with information on test specimen construction.
Garcia, A.↗
Design, analysis, and test verification of advanced encapsulation systems
The construction of optical and electrical verification test coupons is detailed. Testing of these coupons was completed and the results are presented. Additionally, a thermal simulation of roof mounted array conditions was done and the results documented.
Garcia, A.↗
Design, analysis and test verification of advanced encapsulation systems, phase 2 program results
Optical, electrical isolation, thermal structural, structural deflection, and thermal tests are reported. The utility of the optical, series capacitance, and structural deflection models was verified.
Garcia, A.↗
Analysis, design, fabrication and testing of an optical tip clearance sensor
Analyses and the design, fabrication, and testing of an optical tip clearance sensor with intended application in aircraft propulsion control systems are reported. The design of a sensor test rig, evaluation of optical sensor components at elevated temperatures, sensor design principles, sensor test results at room temperature, and estimations of sensor accuracy at temperatures of an aircraft engine environment are discussed. Room temperature testing indicated possible measurement accuracies of less than 12.7 microns (0.5 mils). Ways to improve performance at engine operating temperatures are recommended. The potential of this tip clearance sensor is assessed.
Poppel, G. L.↗
Design analysis of a self-acting spiral-groove ring seal for counter-rotating shafts
A self-acting spiral groove inter-shaft ring seal of nominal 16.33 cm (6.43 in.) diameter for sealing fan bleed air between counter rotating shafts in advanced turbofan engines was analyzed. The analysis focused on the lift force characteristics of the spiral grooves. A NASA Lewis developed computer program for predicting the performance of gas lubricated face seals was used to optimize the spiral groove geometry to produce maximum lift force. Load capacity curves (lift force as function of film thickness) were generated for four advanced turbofan engine operating conditions at relative seal speeds ranging from 17,850 to 29,800 rpm, sealed air pressures from 6 to 42 N/sq cm (9 to 60 psi) absolute and temperatures from 95 to 327 C (203 to 620 F). The relative seal sliding speed range was 152 to 255 m/sec (500 to 836 ft/sec). The analysis showed that the spiral grooves are capable of producing sufficient lift force such that the ring seal will operate in a noncontacting mode over the operating range of typical advanced turbofan engines.
Dirusso, E.↗
Design, analysis and test verification of advanced encapsulation systems
A preliminary reduced variable master was constructed for pressure loading. A study of cell thickness versus cell stress was completed. Work is continuing on encapsulation of qualification modules. A 4 ft x 4 ft 'credit card' construction laminate was made.
Garcia, A., III↗
Design analysis of a self-acting spiral-groove ring seal for counter-rotating shafts
A self-acting spiral groove inter-shaft ring seal of nominal 16.33 cm (6.43 in.) diameter for sealing fan bleed air between counter-rotating hafts in advanced turbofan engines was analyzed. The analysis focused on the lift force characteristics of the spiral grooves. A NASA Lewis developed computer program for predicting the performance of gas lubricated face seals was used to optimize the spiral groove geometry to produce maximum lift force. Load capacity curves (lift force as function of film thickness) were generated for four advanced turbofan engine operating conditions at relative seal speeds ranging from 17,850 to 29,800 rpm, sealed air pressures from 6 to 42 N/sq cm (9 to 60 psi) absolute and temperatures from 95 deg to 327 C (203 deg to 620 F). The relative seal sliding speed range was 152 to 255 m/sec (500 to 836 ft/sec). The analysis showed that the spiral grooves are capable of producing sufficient lift force such that the ring seal will operate in a noncontacting mode over the operating range of typical advanced turbofan engines.
Dirusso, E.↗
Design, analysis and test verification of advanced encapsulation systems
Analytical models were developed to perform optical, thermal, electrical and structural analyses on candidate encapsulation systems. From these analyses several candidate encapsulation systems were selected for qualification testing.
Garcia, A., III↗
Design, analysis and test of composite curved frames for helicopter fuselage structure
Curved beam effects in composite frame structures representative of a light helicopter airframe are examined, and currently available analytical methods for studying these effects are briefly reviewed. A finite element study of curved composite frames is then reported, and it is shown that the curved frame effects must be accurately accounted for to avoid premature fracture. The finite element method is shown to be accurate to within 10 percent in accounting for the curved beam effects in composite structures.
Rich, M. J.↗
Design analysis of a self-acting spiral-groove ring seal for counter-rotating shafts
A self-acting spiral groove inter-shaft ring seal of nominal 16.33 cm (6.43 in.) diameter for sealing fan bleed air between counter rotating shafts in advanced turbofan engines was analyzed. The analysis focused on the lift force characteristics of the spiral grooves. A NASA Lewis developed computer program for predicting the performance of gas lubricated face seals was used to optimize the spiral groove geometry to produce maximum lift force. Load capacity curves (lift force as function of film thickness) were generated for four advanced turbofan engine operating conditions at relative seal speeds ranging from 17,850 to 29,800 rpm, sealed air pressures from 6 to 42 N/sq cm (9 to 60 Psi) absolute and temperatures from 95 to 327 C (203 to 620 F). The relative seal sliding speed range was 152 to 255 m/sec (500 to 836 ft/sec). The analysis showed that the spiral grooves are capable of producing sufficient lift force such that the ring seal will operate in a noncontacting mode over the operating range of typical advanced turbofan engines. Previously announced in STAR as N83-23306
Di Russo, EL↗
Design, analysis and test verification of advanced encapsulation systems
Investigations into transparent conductive polymers were begun. Polypyrrole was electrochemically deposited, but the film characteristics were poor. A proprietary polymer material supplied by Polaroid was evaluated and showed promise as a readily processable material. A method was developed for calculating the magnitude and location of the maximum electric field for the family of solar-cell-like shapes. A method for calculating the lines of force for three dimensional electric fields was developed and applied to a geometry of interest to the photovoltaic program.
Garcia, A., III↗
A system approach to design-analysis
Today, the increased use of Finite Element Analysis coupled with computer graphics interfaces presents the analyst with many alternatives. The drive toward automation has resulted in the creation of many modeling and post-processing systems that are in use today throughout the world. Many of these systems exist as islands of technology. The need for fully integrated systems is being met by many companies today.
White, G.↗
F-106 data summary and model results relative to threat criteria and protection design analysis
The NASA F-106 has acquired considerable data on the rates-of-change of EM parameters on the aircraft surface during 690 direct lightning strikes while penetrating thunderstorms at altitudes from 15,000 to 40,000 feet. The data are presently being used in updating previous lightning criteria and standards. The new lightning standards will, therefore, be the first which reflect actual aircraft responses measured at flight altitudes.
Pitts, F. L.↗