Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dilatancy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The comparative strength and fracture toughness properties of commercial 95W-3.5Ni1.5Fe and 95W-3.5Ni1.5Cu tungsten heavy alloys

Due to the sharp surface cracks resulting from high and cyclic thermal loads, fracture toughness is a crucial property for fusion divertor materials. Tungsten heavy alloys (WHA) have emerged as a leading candidate for plasma facing component applications. Both the WNiFe and WNiCu WHAs have been considered. However, there is no fracture toughness data in the literature on the WNiCu WHA. Therefore, maximum load elastic–plastic fracture toughness (K Jm ) of a commercial 95W-3.5Ni1.5Cu (NiCu) WHA plate is reported here for the first time. The NiCu WHA K Jm is compared to a corresponding K Jm for commercial 95W-3.5Ni1.5Fe (NiFe) WHA, along with comparisons of their respective microstructures, microhardness, and tensile properties. Although their room temperature yield strengths are similar (≈ 600 MPa), the NiFe WHA has higher ultimate stress (818 MPa vs. 642 MPa) and total elongation (8% vs. 1.2%) compared to the NiCu WHA. Most notably, the room temperature elastic–plastic K Jm for the NiFe WHA of ≈ 80 ± 8 MPa$\sqrt{m}$, is nearly twice that of the NiCu WHA at ≈ 47 ± 4 MPa$\sqrt{m}$. Further, while the NiFe WHA experienced stable ductile tearing, the crack propagated unstably (approximately elastically) after reaching the maximum load in the NiCu WHA. The higher K Jm of the NiFe WHA is attributed to its higher flow stress and ductility, along with the energy dissipation and microcrack dilatational stress shielding, provided by a wide distribution of arrested process-zone microcracks, which are largely absent in the NiCu WHA. Since, the 95W-NiFe WHA has distinctly better mechanical properties than 95W-NiCu WHA, it is a more suitable candidate for the fusion reactor application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Ordinary and exotic mesons in the extended Linear Sigma Model

The extended Linear Sigma Model (eLSM) is a hadronic model based on the global symmetries of QCD and the corresponding explicit, anomalous, and spontaneous breaking patterns. In its basic three-flavor form, its mesonic part contains the dilaton/glueball as well as the nonets of pseudoscalar, scalar, vector, and axial–vector mesons, thus chiral symmetry is linearly realized. In the chiral limit and neglecting the chiral anomaly, only one term – within the dilaton potential – breaks dilatation invariance, and all terms are chirally symmetric. Spontaneous symmetry breaking is implemented by a generalization of the Mexican-hat potential, with explicit symmetry breaking responsible for its tilting. The overall mesonic phenomenology up to ~2 GeV is in agreement with the PDG compilation of masses and partial and total decay widths. The eLSM was enlarged in a straightforward way to include other conventional quark–antiquark nonets (pseudovector and orbitally excited vector mesons, tensor and axial-tensor mesons, radially excited (pseudo)scalar mesons, etc.), as well as two nonets of hybrid mesons, the lightest one with exotic quantum numbers J $\mathscr{PC}$ = 1 -+ not allowed for $\bar{q}q$ objects, such as the resonance π 1 (1600) and the recently discovered η 1 (1855) . In doing so, different types of chiral multiplets are introduced: heterochiral and homochiral multiplets, which differ in the way they transform under chiral transformations. Moreover, besides the scalar glueball that is present from the beginning as dilaton, other glueballs, the tensor, the pseudoscalar and the vector glueballs were coupled to the eLSM: the scalar resonance ƒ 0 (1710) turns out to be mostly gluonic, the tensor glueball couples strongly to vector mesons, and the pseudoscalar glueball couples sizably to $ππη'$ and can be assigned to X (2370) or X (2600). In all cases above, masses and decays can be analyzed allowing for a better understanding of both conventional and non-conventional mesons: whenever data are available, a comparison is performed and, when this is not the case, predictions of decay widths and decay ratios are outlined. The eLSM contains chiral partners on an equal footing and is therefore well suited for studies of chiral symmetry restoration at nonzero temperature and densities: this is done by coupling it to the Polyakov loop. Finally, the QCD phase diagram and the location of the critical endpoint were investigated within this framework.

Chiral symmetry↗
DOE OSTI2021

Simulation and flow physics of a shocked and reshocked high-energy-density mixing layer

This work describes a computational investigation of multimode instability growth and multimaterial mixing induced by multiple shock waves in a high-energy-density (HED) environment, where pressures exceed 1 Mbar. The simulations are based on a series of experiments performed at the National Ignition Facility (NIF) and designed as an HED analogue of non-HED shock-tube studies of the Richtmyer–Meshkov instability and turbulent mixing. A three-dimensional computational modelling framework is presented. It treats many complications absent from canonical non-HED shock-tube flows, including distinct ion and free-electron internal energies, non-ideal equations of state, radiation transport and plasma-state mass diffusivities, viscosities and thermal conductivities. The simulations are tuned to the available NIF data, and traditional statistical quantities of turbulence are analysed. Integrated measures of turbulent kinetic energy and enstrophy both increase by over an order of magnitude due to reshock. Large contributions to enstrophy production during reshock are seen from both the baroclinic source and enstrophy–dilatation terms, highlighting the significance of fluid compressibility in the HED regime. Dimensional analysis reveals that Reynolds numbers and diffusive Péclet numbers in the HED flow are similar to those in a canonical non-HED analogue, but conductive Péclet numbers are much smaller in the HED flow due to efficient thermal conduction by free electrons. It is shown that the mechanism of electron thermal conduction significantly softens local spanwise gradients of both temperature and density, which causes a minor but non-negligible decrease in enstrophy production and small-scale mixing relative to a flow without this mechanism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Elastic Properties of Plasma-Exposed Tungsten Predicted by Molecular-Dynamics Simulations

We report results of systematic molecular-dynamics computations of the elastic properties of single-crystalline tungsten containing structural defects, voids and overpressurized He nanobubbles, related to plasma exposure of tungsten serving as a plasma- facing component (PFC) in nuclear fusion devices. Our computations reveal that the empty voids are centers of dilatation resulting in development of tensile stress in the tungsten matrix, whereas He-filled voids (nanobubbles) introduce compressive stress in the plasma-exposed tungsten. We find that the dependence of the elastic moduli of plasma-exposed tungsten, namely, the bulk, Young, and shear modulus, on its void fraction follows a universal exponential scaling relation. We also find that the elastic moduli of plasma-exposed tungsten soften substantially as a function of He content in the tungsten matrix, following an exponential scaling relation; this He-induced exponential softening is in addition to the softening caused in the matrix with increasing temperature. A systematic characterization of the dependence of the elastic moduli on the He bubble size reveals that He bubble growth affects significantly both the bulk modulus and the Poisson ratio of plasma-exposed tungsten, while its effect on the Young and shear moduli of the plasma-exposed material is weak. Our findings contribute directly to the development of a structure-properties database that is required for the predictive modeling of the dynamical response of PFCs in nuclear fusion devices.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Atomistic Mechanisms of Stress-Dependent Molten Salt Corrosion in NiCr Alloys

Ni-based structural alloys in molten salt environments often experience simultaneous mechanical loading and corrosive attack, yet the mechanisms governing stress-corrosion interactions remain unclear. Prior studies largely emphasize tensile stress, while the role of compressive stress has received limited attention. Here, reactive molecular dynamics simulations are used to investigate the coupled effects of applied strain and corrosion in Ni 0.75 Cr 0.25 exposed to molten FLiNaK at 800 °C. A Σ5(210) grain boundary model is subjected to tensile (+4%) to compressive (−4%) uniaxial strains, and corrosion behavior is evaluated through fluorine adsorption, charge redistribution, and grain boundary evolution. Tensile strain accelerates intergranular corrosion susceptibility by reducing local atomic packing through elastic dilation and increasing excess free volume at the grain boundary, which enhances atomic mobility and salt infiltration. In contrast, compressive strain can suppress corrosion by promoting the formation of a ridge-like surface layer along the grain boundary, limiting salt access to the underlying alloy. These results provide atomistic insight into how stress states influence grain boundary corrosion in molten salts.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

A Review of Computational Models for the Flow of Milled Biomass Part II: Continuum-Mechanics Models

The design of efficient material-handling systems for milled lignocellulosic biomass is challenging due to their complex particle morphologies and frictional interactions. Computational modeling, including the discrete element method (DEM) and continuum-based finite-element/volume methods, may offer scientific insight and predictive capabilities for the flow of milled biomass in hoppers and feeders. Herein, this article (Part II) presents a review of current state-of-the-art continuum models for the flow of milled biomass, whereas DEM models are reviewed in a companion article (Part I). Advances of numerical methods to solve the global governing equations are discussed first, followed by a comprehensive review of constitutive models for granular materials, including Drucker–Prager, hypoplastic, Cambridge-type, inertial-rheology, and nonlocal granular fluidity models. Specifically, we provide in-depth discussion on the suitability of those models for milled lignocellulosic biomass materials in terms of nonlinear elasticity, dependence of flow strength on pressure, density and shear rate, and compaction (dilation) associated with hardening (softening). Furthermore, our study shows that, despite the recent advances in continuum granular flow modeling, the most suitable constitutive models still need further development to account for material parametrization, multiflow regimes, and multiscale behavior before they can be reliably used to optimize the design and operation of biomass handling systems.

09 BIOMASS FUELS↗
DOE OSTI2020

The Complicated Link Between Material Properties and Microfracture Density for an Underground Explosion in Granite

Geophysical techniques are often implemented as quick and inexpensive ways to locate and characterize fractures in the subsurface, which is important for a number of geoscience fields. Seismic velocities are the most widely used proxies for identification of fractures, but the correlation is not always well-defined. In this study we present material property data: unconfined compressive strength (UCS), bulk density (ρ), Young's modulus (E), Poisson's ratio (ν), P wave velocity (V p ), and S wave velocity (V s ), in conjunction with microfracture densities measured on samples of granite collected before and after underground chemical explosions. Results indicate the relationship between fractures and material properties is complex, even in this single-lithology environment. We interpret that this complexity arises from varying fracture mechanisms (e.g. dilation-inducing fractures vs compression-inducing fractures) in different parts of the core, due to differences in stress conditions. Additional complexity may result from chemical interactions between the fresh fractures and the fluids in the area. Water content appears to have a significant, if not dominant, role in the unconfined compressive strength (UCS) of the samples. We suggest caution when using elastic property measurements as a proxy for fracturing in areas of explosion-induced damage, or in other areas where a variety of mechanisms induce fracturing.

58 GEOSCIENCES↗
DOE OSTI2022

Frictional and Lithological Controls on Shallow Slow Slip at the Northern Hikurangi Margin

Slow slip events (SSEs) have been identified at subduction zones globally as an important link in the continuum between elastodynamic ruptures and stable creep. The northern Hikurangi margin is home to shallow SSEs which propagate to within 2 km of the seafloor and possibly to the trench, providing insights into the physical conditions conducive to SSE behavior. We report on a suite of friction experiments performed on protolith material entering the SSE source region at the Hikurangi margin, collected during the International Ocean Discovery Program Expedition 375. We performed velocity stepping and slide-hold-slide experiments over a range of fault slip rates, from plate rate (5 cm/yr or 1.6 × 10 –9 m/s) to ~1 mm/s (10 –3 m/s) and quantified the frictional velocity dependence and healing rates for a range of lithologies atdifferent stresses. The frictional velocity dependence (a-b) and critical slip distance DC increase with fault slip rate in our experiments. We observe atransition from velocity weakening to strengthening at slip rates of ~0.3 µm/s. This velocity dependence of DC could be due to a combination of dilatant strengthening and a widening of the active shear zone at higher slip rates. We document low healing rates in the clay-rich volcaniclastic conglomerates, which lie above the incoming plate basement at least locally, and relatively higher healing rates in the chalk lithology. Finally, our experimental constraints on healing rates in different input lithologies extrapolated to timescales of 1–10 years are consistent with the geodetically inferred low stress drops and healing rates characteristic of the Hikurangi SSEs.

58 GEOSCIENCES↗
DOE OSTI2022

Hydro-Mechanical Measurements of Sheared Crystalline Rock Fractures With Applications for EGS Collab Experiments 1 and 2

We present hydro-mechanical measurements that characterize shear on natural fractures in schist, amphibolite, and rhyolite specimens from the enhanced geothermal system (EGS) Collab Project's Experiment 1 and 2 sites (E1 and E2) at the Sanford Underground Research Facility. We employed a triaxial direct shear method augmented with X-ray imaging to perform hydroshearing (injection-induced shearing) and mechanical shearing on naturally fractured specimens at in situ stress conditions. Measurements included fracture permeability, strength, stress-dependent aperture, shear dilation, and frictional strength. Results reveal that in situ natural fractures must be permeable, weak, and shear-oriented to be hydrosheared, and only a subset of the observable in situ fractures were suitable. When sheared, the fracture permeability typically increased by a factor of 10 or more and this increase was retained over time. However, shear slip did not always result in permeability increase. High phyllosilicate content associated with exceptionally weak fractures exhibited poor or even decreased permeability after stimulation. These measurements in combination with site data were used to conduct a slip-tendency analysis for different fracture sets, and we selected the top candidate natural fractures for hydroshearing at the EGS Collab sites. We also found that the lower in situ shear stress and stronger fractures at the E2 site make hydroshearing more challenging than at the E1 site. Overall, the methods and analysis used in our work can be applied to any geothermal project to identify in situ joint sets that are best suited for hydroshearing, which in turn can help to optimize well placement and energy production.

58 GEOSCIENCES↗
DOE OSTI2023

Active‐Source Seismic Imaging of Fault Re‐Activation and Leakage: An Injection Experiment at the Mt Terri Rock Laboratory, Switzerland

Abstract We conducted a time‐lapse seismic experiment utilizing automated active seismic source and sensor arrays to monitor a reactivated fault within the Opalinus clay formation at the Mont Terri Rock Laboratory (Switzerland), an analog caprock for geologic carbon storage. A series of six brine injections were conducted into the so‐called Main Fault to reactivate it. Seismic instrumentation in five monitoring boreholes on either side of the fault was used to continuously probe changes in P‐wave travel‐times associated with fault displacement and leakage. We performed time‐lapse travel‐time tomography on five hundred sequential data sets; this revealed a zone of decreased P‐wave velocity, up to 16 m/s, during each injection cycle, followed by a velocity increase during shut‐in. These results demonstrate varying elastic property perturbations, both spatially and temporally, along the fault plane during reactivation. We then interpreted these velocity changes in terms of fault dilation induced by pressurized fluids along the fault.

58 GEOSCIENCES↗
DOE OSTI2025

Control Mechanisms for Self‐Sealing in Activated Clay‐Rich Faults Through Controlled Hydraulic Injection Experiment

Abstract In a high‐pressure injection fault activation experiment conducted at the Mont Terri underground research laboratory in Switzerland, the transmissivity of the Opalinus Clay fault significantly increased due to opening and shearing. The fluid injection, spanning a few hours, generated a 10 m radius fault activation patch. Subsequent pressure pulse tests conducted bi‐weekly for a year revealed the gradual return of fault transmissivity to its initial state. The study utilized fluid pressure decay analysis, optical fiber monitoring, continuous active source seismic measurements and borehole displacement sensors for measuring fault displacements. The fault zone exhibited a dilation of approximately 1.4 mm, associated with both normal and tangential movements during activation, resulting in a sudden transmissivity increase from 1 × 10 −12 to 3.2 × 10 −7 m 2 /s. Early post‐activation, transient compaction and the subsequent slow compaction were observed, transitioning to an extension regime. The pressure pulse tests demonstrated a rapid transmissivity drop by more than two orders of magnitude within the first 10 days, followed by a gradual and less pronounced decrease. Plastic shear and compaction dominated the transmissivity evolution until 70 days after injection ended, followed by a period where additional factors, such as clay mineral swelling, influenced the behavior. Extrapolation suggested a sealing process taking at least 50 years after the initial activation. Plain Language Summary A field‐scale fault activation experiment offers valuable insights into the elasto‐plastic processes governing the sealing of shale faults. The experiment reveals a rapid increase in the fault's transmissivity by approximately five orders of magnitude during activation. Subsequent observations show a gradual transmissivity decrease by about three orders of magnitude post‐activation, with slow long‐term plastic shear and compaction of the fault competing against secondary processes, notably clay mineral swelling. All conceptual models employed to interpret these field data converge on the estimation that the fault's return to its initial low transmissivity state would require a minimum of 50 years. Key Points High‐pressure injection fault activation experiment at the Mont Terri underground research laboratory Continuous transmissivity measurements record self‐sealing inside a clay‐rich fault zone Transmissivity undergoes a phase of domination by slow plastic compaction and shearing during the initial post‐activation period, with mineral swelling exerting its influence over the long term

Guglielmi, Yves↗
DOE OSTI2025

Crystallographic Texture, Structure, and Stress Transmission in Nugget Sandstone Examined With X‐Ray Tomography and Diffraction Microscopy

Subsurface processes in sandstones are controlled by porosity, permeability, and deformation mechanisms, all of which are controlled by a complex interplay of crystallographic rock texture, structure, and micromechanics. Texture, structure, and micromechanics have historically been studied using optical and electron microscopy of thin-sections. Here, we employed a new combination of in situ X-ray tomography and ray diffraction microscopy to study crystallographic texture, structure, and grain stresses in 3D. We examined these features in a sample of Nugget sandstone, a sandstone constituting hydrocarbon reservoirs across the American West. Our aims are threefold. First, we demonstrate the utility of X-ray diffraction microscopy probes for revealing texture, structure, and stress transmission in 3D. Second, we apply these techniques to Nugget sandstone and discuss findings in the context of prior work. Third, we study grain stress tensor evolution during mechanical compression to examine whether their heterogeneity and orientation evolution reflect that of inter-particle forces in granular materials. Our results show: (a) larger grains featured higher intra-granular misorientations, possibly from an increased prevalence of cements; (b) pores closed parallel to the loading direction and opened normal to loading; (c) grain stresses featured heterogeneity and orientations similar to inter-particle forces in non-cohesive granular materials; (d) grains featured compressive stresses in the loading direction and tensile stresses orthogonal to the loading direction, the latter resisting sample dilation and grain separation. Our work demonstrates the first known application of multi-modal X-ray tomography and diffraction microscopy to sandstone, providing new 3D insight into the nature of quartz cement and stress evolution.

high energy diffraction microscopy↗
DOE OSTI2020

High-speed volumetric two-photon fluorescence imaging of neurovascular dynamics

Abstract Understanding the structure and function of vasculature in the brain requires us to monitor distributed hemodynamics at high spatial and temporal resolution in three-dimensional (3D) volumes in vivo. Currently, a volumetric vasculature imaging method with sub-capillary spatial resolution and blood flow-resolving speed is lacking. Here, using two-photon laser scanning microscopy (TPLSM) with an axially extended Bessel focus, we capture volumetric hemodynamics in the awake mouse brain at a spatiotemporal resolution sufficient for measuring capillary size and blood flow. With Bessel TPLSM, the fluorescence signal of a vessel becomes proportional to its size, which enables convenient intensity-based analysis of vessel dilation and constriction dynamics in large volumes. We observe entrainment of vasodilation and vasoconstriction with pupil diameter and measure 3D blood flow at 99 volumes/second. Demonstrating high-throughput monitoring of hemodynamics in the awake brain, we expect Bessel TPLSM to make broad impacts on neurovasculature research.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Constraining maximum event magnitude during injection-triggered seismicity

Abstract Understanding mechanisms controlling fluid injection-triggered seismicity is key in defining strategies to ameliorate it. Recent triggered events (e.g. Pohang, Mw 5.5) have exceeded predictions of average energy release by a factor of >1000x, necessitating robust methodologies to both define critical antecedent conditions and to thereby constrain anticipated event size. We define maximum event magnitudes resulting from triggering as a function of pre-existing critical stresses and fluid injection volume. Fluid injection experiments on prestressed laboratory faults confirm these estimates of triggered moment magnitudes for varied boundary conditions and injection rates. In addition, observed ratios of shear slip to dilation rates on individual faults signal triggering and may serve as a measurable proxy for impending rupture. This new framework provides a robust method of constraining maximum event size for preloaded faults and unifies prior laboratory and field observations that span sixteen decades in injection volume and four decades in length scale.

58 GEOSCIENCES↗
DOE OSTI2022

Vanilloid-dependent TRPV1 opening trajectory from cryo EM ensemble analysis

Single particle cryo-EM often yields multiple protein conformations within a single dataset, but experimentally deducing the temporal relationship of these conformers within a conformational trajectory is not trivial. Here, we use thermal titration methods and cryo-EM in an attempt to obtain temporal resolution of the conformational trajectory of the vanilloid receptor TRPV1 with resiniferatoxin (RTx) bound. Based on our cryo-EM ensemble analysis, RTx binding to TRPV1 appears to induce intracellular gate opening first, followed by selectivity filter dilation, then pore loop rearrangement to reach the final open state. This apparent conformational wave likely arises from the concerted, stepwise, additive structural changes of TRPV1 over many subdomains. Greater understanding of the RTx-mediated long-range allostery of TRPV1 could help further the therapeutic potential of RTx, which is a promising drug candidate for pain relief associated with advanced cancer or knee arthritis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Trans-crustal structural control of CO 2 -rich extensional magmatic systems revealed at Mount Erebus Antarctica

Erebus volcano, Antarctica, with its persistent phonolite lava lake, is a classic example of an evolved, CO 2 -rich rift volcano. Seismic studies provide limited images of the magmatic system. Here we show using magnetotelluric data that a steep, melt-related conduit of low electrical resistivity originating in the upper mantle undergoes pronounced lateral re-orientation in the deep crust before reaching shallower magmatic storage and the summit lava lake. The lateral turn represents a structural fault-valve controlling episodic flow of magma and CO 2 vapour, which replenish and heat the high level phonolite differentiation zone. This magmatic valve lies within an inferred, east-west structural trend forming part of an accommodation zone across the southern termination of the Terror Rift, providing a dilatant magma pathway. Unlike H 2 O-rich subduction arc volcanoes, CO 2 -dominated Erebus geophysically shows continuous magmatic structure to shallow crustal depths of < 1 km, as the melt does not experience decompression-related volatile supersaturation and viscous stalling.

58 GEOSCIENCES↗
DOE OSTI2022

Transient evolution of permeability and friction in a slowly slipping fault activated by fluid pressurization

The mechanisms of permeability and friction evolution in a natural fault are investigated in situ. During three fluid injection experiments at different places in a fault zone, we measured simultaneously the fluid pressure, fault displacements and seismic activity. Changes in fault permeability and friction are then estimated concurrently. Results show that fault permeability increases up to 1.58 order of magnitude as a result of reducing effective normal stress and cumulative dilatant slip, and 19-to-60.8% of the enhancement occurs without seismic emissions. When modeling the fault displacement, we found that a rate-and-state friction and a permeability dependent on both slip and slip velocity together reasonably fit the fault-parallel and fault-normal displacements. This leads to the conclusion that the transient evolution of fault permeability and friction caused by a pressure perturbation exerts a potentially dominant control on fault stability during fluid flow.

58 GEOSCIENCES↗
DOE OSTI2023

Combining data and theory for derivable scientific discovery with AI-Descartes

Abstract Scientists aim to discover meaningful formulae that accurately describe experimental data. Mathematical models of natural phenomena can be manually created from domain knowledge and fitted to data, or, in contrast, created automatically from large datasets with machine-learning algorithms. The problem of incorporating prior knowledge expressed as constraints on the functional form of a learned model has been studied before, while finding models that are consistent with prior knowledge expressed via general logical axioms is an open problem. We develop a method to enable principled derivations of models of natural phenomena from axiomatic knowledge and experimental data by combining logical reasoning with symbolic regression. We demonstrate these concepts for Kepler’s third law of planetary motion, Einstein’s relativistic time-dilation law, and Langmuir’s theory of adsorption. We show we can discover governing laws from few data points when logical reasoning is used to distinguish between candidate formulae having similar error on the data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗