Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Correlation of Early-Stage Growth Process Conditions with Dislocation Evolution in MOCVD-Based GaP/Si Heteroepitaxy

To identify the complex relationships between early-stage growth processes and the resultant defect microstructure in GaP/Si heteroepitaxy, a holistic study of several key metal-organic chemical vapor deposition (MOCVD) parameters was conducted, focusing on Si surface preparation and GaP atomic layer epitaxy (ALE) based nucleation processes. Here, crystalline defects related to the lattice mismatch and/or interfacial heterovalency, namely misfit dislocations (MD), threading dislocations (TD), and stacking fault pyramids (SFP), were quantitatively characterized via electron channeling contrast imaging (ECCI) and correlated against the different process variations. Choice of Si surface preparation method between the two examined (dilute SiH4 annealing versus Si2H6 based homoepitaxy) had little impact on resultant GaP film morphology and defect content, whereas differing GaP ALE nucleation conditions produced much more substantial changes. In particular, the initial precursor species (tert-butylphosphine versus triethygallium) and ALE cycle purge times both yielded significant influence over threading dislocation densities (TDD) in thin (100 nm), post-critical thickness GaP/Si films, with TDD spanning two orders of magnitude, from 6.7×10 7 cm -2 to 7.1×10 5 cm -2 , depending on the specific process conditions employed. SFP densities were also found to follow a similar trend, ranging from 2.0×10 7 cm -2 to 1.8×10 5 cm -2 , but with no apparent causal relationship between SFP density and TDD. To help explain the dramatic differences observed, detailed, large-area MD network characterization was used to provide statistically-relevant quantitative analyses of the critical dislocation dynamics (introduction rates and glide velocities) associated with the different process variants. These extracted values are then correlated against the ALE process variants to provide insight into the potential mechanistic roles of the different growth processes.

36 MATERIALS SCIENCE↗

Mechanical properties and deformation mechanisms of single crystal Mg micropillars subjected to high-strain-rate C-axis compression

Here, the mechanical properties and deformation mechanisms of single crystal magnesium under c-axis quasi-static and high-strain rate compressions are investigated through in situ scanning electron microscope (SEM) experiments and post-mortem transmission electron microscope (TEM) characterization. The findings revealed that ductility and high rates of hardening are preserved for pillars as large as 15 μm. Furthermore, rate effects result in a mild increase in flow stress with plastic deformations controlled primarily by the slip of type dislocations. Importantly and in contrast to other literature reports, plastic deformation occurs in the absence of twining. As the strain increases and plastic deformation exceeds about 4%, crystal rotation activates basal slip, <$\mathrm{a}$> type dislocations, resulting in a more rate independent flow stress. TEM observation on micropillars compressed at a strain rate of 250/s, revealed the activation of {${11}$$\bar{2}$$\bar{2}$} < $\bar{1}$$\bar{1}23$ > slip systems and high mobility of screw dislocations as major contributors to plastic strains in excess of 10% without fracture. These findings are relevant to the design of lightweight materials used in transportation systems, e.g., selection of material grain size. Moreover, the experimental data here reported provides the materials science community with a unique opportunity to validate discrete dislocation dynamics (DDD) formulations employed in multiscale design of materials.

36 MATERIALS SCIENCE↗

Vacancy-Mediated Increases in Brine–Salt Surface Energies

Salt formations have been explored for the permanent isolation of spent nuclear fuel based on their high thermal conductivity, self-healing nature, and low hydraulic permeability to brine flow. Vacancy defect concentrations in salt complicate fracture mechanics not driven by dislocation dynamics and can influence the resulting surface structure. Classical molecular dynamic simulations were used to simulate tensile testing of salt crystals (halite) with vacancy defect concentrations of up to 0.5 defects/nm 3 . Increasing defect concentrations resulted in a decrease in ultimate tensile strength and fracture surface energies, driven by increased surface roughness rather than changes in the amount of surface area. Brine–salt surface energies of the fractured surfaces were 0.22 to 0.26 J/m 2 , significantly higher than values reported for atomically flat (100) surfaces at the same brine composition. This change in surface energy increased the brine–salt dihedral angle by ~27°. The dihedral angle threshold for percolation in salt is 60°, and a 27° increase due to rough fracture surfaces identifies a reduction in porosity percolation and a decrease in salt permeability. Therefore, bedded salt and salt domes may be even more stable than those previously predicted from dihedral angle calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extending Interfaces in 3D to Achieve Superior Nanoscale Strength in Ti/Nb Nanolaminates

Tuning the atomic-level structure of nanolaminates enables high strength, increased deformability, and the ability to absorb and mitigate damage due to varied crystalline defects, including dislocations. Here, we present the enhanced strength of Ti/Nb nanolaminates containing thick 3D interfaces (3DIs), relative to their chemically abrupt 2D counterparts. We examine the effects of crystallographic alignment and compositional gradients on mechanical behavior via experiments and phase-field-dislocation dynamics (PFDD) modeling. Mechanical testing reveals that nanolaminates containing thicker 3DIs demonstrate a 28% hardness enhancement compared with sharp-interface nanolaminates. PFDD modeling shows that the critical resolved shear stress (CRSS) increases with the 3DI thickness. Gradual compositional transitions in 3DIs were confirmed via scanning transmission electron microscopy and high-resolution transmission electron microscopy, showing sharp crystallographic transitions and a heightened interface topography. The findings establish a positive function between the 3DI thickness and mechanical robustness for hexagonal-closest-packed-containing composites, emphasizing the role of defect–interface interactions in tailoring the mechanical performance and providing a foundation for future interfacial engineering.

36 MATERIALS SCIENCE↗

Operando real-space imaging of a structural phase transformation in the high-voltage electrode LixNi0.5Mn1.5O4

Abstract Discontinuous solid-solid phase transformations play a pivotal role in determining the properties of rechargeable battery electrodes. By leveraging operando Bragg Coherent Diffractive Imaging (BCDI), we investigate the discontinuous phase transformation in Li x Ni 0.5 Mn 1.5 O 4 within an operational Li metal coin cell. Throughout Li-intercalation, we directly observe the nucleation and growth of the Li-rich phase within the initially charged Li-poor phase in a 500 nm particle. Supported by the microelasticity model, the operando imaging unveils an evolution from a curved coherent to a planar semi-coherent interface driven by dislocation dynamics. Our data indicates negligible kinetic limitations from interface propagation impacting the transformation kinetics, even at a discharge rate of C/2 (80 mA/g). This study highlights BCDI’s capability to decode complex operando diffraction data, offering exciting opportunities to study nanoscale phase transformations with various stimuli.

Sun, Yifei (ORCID:0000000295625120)↗

Predictions of an alternative pathway for grain-boundary driven twinning

The exceptional strength of nanoscale metallic grains is due to strain-accommodation mechanisms that are uncommon in their coarse-grained counterparts, such as deformation twinning. Using an $ab initio$ density functional theory-phase field dislocation dynamics model, we provide evidence of an unconventional kinetic pathway for twin formation in nano-sized crystals involving two grain boundaries. It corresponds to greater favorability because it accommodates strain yet removes debilitating backstresses. A simple map is presented to relate the associated kinetics of nucleation and propagation to intrinsic material defect formation energies.

36 MATERIALS SCIENCE↗

Real-space visualization of a defect-mediated charge density wave transition

Here, we study the coupled charge density wave (CDW) and insulator-to-metal transitions in the 2D quantum material 1T-TaS 2 . By applying in situ cryogenic 4D scanning transmission electron microscopy with in situ electrical resistance measurements, we directly visualize the CDW transition and establish that the transition is mediated by basal dislocations (stacking solitons). We find that dislocations can both nucleate and pin the transition and locally alter the transition temperature T c by nearly ~75 K. This finding was enabled by the application of unsupervised machine learning to cluster five-dimensional, terabyte scale datasets, which demonstrate a one-to-one correlation between resistance—a global property—and local CDW domain-dislocation dynamics, thereby linking the material microstructure to device properties. This work represents a major step toward defect-engineering of quantum materials, which will become increasingly important as we aim to utilize such materials in real devices.

4D-STEM↗

Complex dislocation loop networks as natural extensions of the sink efficiency of saturated grain boundaries in irradiated metals

The development of radiation-tolerant structural materials is an essential element for the success of advanced nuclear energy concepts. A proven strategy to increase radiation resistance is to create microstructures with a high density of internal defect sinks, such as grain boundaries (GBs). However, as GBs absorb defects, they undergo internal transformations that limit their ability to capture defects indefinitely. Here, we show that, as the sink efficiency of GBs becomes exhausted with increasing irradiation dose, networks of irradiation loops form in the vicinity of saturated or near-saturated GB, maintaining and even increasing their capacity to continue absorbing defects. The formation of these networks fundamentally changes the driving force for defect absorption at GB, from “chemical” to “elastic.” Using thermally-activated dislocation dynamics simulations, we show that these networks are consistent with experimental measurements of defect densities near GB. Our results point to these networks as a natural continuation of the GB once they exhaust their internal defect absorption capacity.

36 MATERIALS SCIENCE↗

Effect of Small Preliminary Deformation on the Evolution of Elastoplastic Waves of Shock Compression in Annealed VT1-0 Titanium

The evolution of an elastoplastic waves of shock compression in VT1-0 titanium in the as-annealed state and after preliminary compression is measured. A preliminary strain of 0.6% and the related increase in the dislocation density are found to change the deformation kinetics radically and to decrease the Hugoniot elastic limit. An increase in the preliminary strain from 0.6% to 5.2% only weakly changes the Hugoniot elastic limit and the compression rate in the plastic shock wave. The measurement results are used to plot the strain rate versus the stress at the initial stage of high-rate deformation, and the experimental results are interpreted in terms of dislocation dynamics.

36 MATERIALS SCIENCE↗

ParaDIS_lib

The ParaDIS_lib software is a project that is funded by the DOE ASC Program. Its purpose is to provide visualization and analysis capabilities for the existing ParaDIS parallel dislocation dynamics simulation code.

Cook, RichardD.↗

Contributions to MoDELib SOFTWARE

The purpose of the current request is to enable LANL employees to contribute computer source code to the existing public repository of the MoDELib software package. This software implements discrete dislocation dynamics (DDD) and finite element (FEM) methods and is currently a vital component of an ongoing DR project at LANL, in collaboration with its original author and maintainer Giacomo Po. Contributions from LANL employees would aim to enhance the reliability, accuracy, and performance of MoDELib simulations using LANL's high performance computing platforms through bug fixes, algorithmic refinements, and parallelization.

Julian, Nicholas↗

Exascale Dislocation Simulator

ExaDiS, or Exascale Dislocation Simulator, is a set of software modules written to enable numerical simulations of large groups of moving and interacting dislocations, line defects in crystals responsible for crystal plasticity. By tracking time evolution of sufficiently large dislocation ensembles, ExaDiS predicts plasticity response and plastic strength of crystalline materials. ExaDiS is built around a library of core functions for Discrete Dislocation Dynamics method specifically written to perform efficient computations on GPUs.

Bertin, Nicolas↗

An approach for estimating the uncertainty in ParaDiS predictions

This report outlines an approach for computing the uncertainties in the predictions of computationally expensive models. While general, we use ParaDiS , a dislocation dynamics simulator originating in Lawrence Livermore National Laboratory, as the target application. ParaDiS is a mesoscale model, and uses submodels constructed/upscaled from microscale (molecular statics and dynamics) simulations. ParaDiS outputs, in turn, are upscaled and used in continuum (macroscale) simulations, e.g., those performed by ALE3D. This report addresses how one may quantify the uncertainties introduced by upscaling (both from microscale to mesoscale, and mesoscale to continuum), and the dependence of uncertainties in ParaDiS predictions on those of the inputs. This dependence is established via sensitivity analysis, and we address how this may be performed with a minimum of ParaDiS runs, given its immense computational cost. This includes constructing a smaller version of the model, sparse sampling of the parameter space, and exploiting the asymptotic nature of the time-evolution of the model outputs. The report concludes with a discussion of the computational resources required to perform this uncertainty quantification study.

97 MATHEMATICS AND COMPUTING↗

Computational design and performance prediction of creep-resistant ferritic superalloys

Ferritic superalloys containing the B2 phase with the parent L21 phase precipitates in a disordered solid-solution matrix, also known as a hierarchical-precipitate-strengthened ferritic alloy (HPSFA), had been developed for high-temperature structural applications in fossil-energy power plants. These alloys were designed by adding Ti into a previously-studied NiAl-strengthened ferritic alloy (denoted as FBB8 in this study). Following with the concept of HPSFAs, in the present research, a systematic investigation on adding other elements, such as Hf and Zr, and optimizing the Ti content within the alloy system, has been conducted, in order to further improve the creep resistance of the model alloys. Studies include advanced experimental techniques, first-principles calculations on thermodynamic and mechanical properties, and numerical simulations on precipitation hardening, have been integrated and conducted to characterize the complex microstructures and excellent creep resistance of alloys. The experimental techniques include transmission-electron microscopy (TEM), scanning-electron microscopy (SEM), neutron diffraction (ND), and atom-probe tomography (APT), which provide the detailed microstructural information of the model alloys. Systematic tension/compression creep tests have also been conducted in order to verify the creep resistance of the potential alloy compositions. The results show that when replacing Ti with Hf and Zr, it does not form the L21 phase. Instead, the hexagonal Laves phase forms and distributes majorly along the grain boundary, or large segregation within grains. Since the Laves phase does not form parent to the B2-phase precipitates, it cannot bring the strengthening effect of HPSFAs. As a result, the FBB8 + 2 wt. % Hf and FBB8 + 2 wt. % Zr alloys have similar mechanical properties to the original FBB8. The FBB8 + Ti series alloys had also been studied, from the creep tests and microstructural characterizations, the FBB8 + 3.5 wt.% Ti possesses the greatest creep resistance, with the L21/B2 phase ratio of 4 (80% of the precipitates is the L21 phase, and 20% is the B2 phase). First-principles calculations include thermodynamics, elastic properties, and interfacial properties, which have been conducted for the understanding of the thermodynamic and mechanical properties of HPSFAs. In addition to the systematic experimental approach and first-principles calculations, a series of numerical tools and algorithms, which assist in the optimization of creep properties of ferritic superalloys, are utilized and developed. These numerical simulation results are compared with the available experimental data and previous first-principles calculations, providing the deep insight of creep mechanisms of the creep-resistant ferritic superalloys. To conclude the present research, we’ve found that (1) only FBB8 + Ti alloys have the potential of forming HPSFA, and FBB8 + Hf and FBB8 + Zr do not work. Therefore, only FBB8 + Ti alloys have desirable creep resistance, (2) the optimum composition for the FBB8 + Ti alloys is FBB8 + 3.5% Ti, which has the greatest creep resistance (218.8 MPa as the threshold stress at 700 oC), (3) first-principle calculations obtained results that could not be obtained in experiments, which are relevant to develop ferritic superalloys with the improved creep resistance, and (4) two-dimensional dislocation-dynamics simulations investigate effects of factors like precipitate volume fractions and precipitate radii in the alloy systems, which helps in developing the most desirable microstructure with greatest strengthening.

20 FOSSIL-FUELED POWER PLANTS↗

Multiscale Modeling of Deformation, Fracture and Failure of Fusion Materials and Structures Final Report

The main objective of the research performed at UCLA under grant number DE-FG02-03ER54708 was to develop a physical understanding of the underlying mechanisms that control high-temperature deformation and fracture of fusion structural materials. The key aspect is the synergistic interaction between thermo-mechanical damage phenomena (e.g. creep, fatigue, and fracture), and irradiation damage phenomena (helium and hydrogen bubbles, and irradiation-induced defects). Another thrust area of the research was on the development of constitutive equations for the mechanical behavior of irradiated structures in fusion components (mainly the First Wall and Plasma-Facing components), and in utilizing them in descriptions in large-scale Finite Element Modeling of fusion structures. A parallel experimental effort on thermo-mechanical and plasma-induced damage is designed to validate and confront the developed theoretical and computational predictions. The models have been experimentally validated through experimental tests in simulated plasma transients on specially-designed W samples. This grant started at UCLA on November 14, 2003 and has had successive continuations till November 14, 2017. Research performed under the grant was to develop a range of hierarchical models for the post-elastic deformation, fracture and failure of fusion structural materials. The developed multiscale modeling approach has been based on rigorous mathematical, physical, and computational methods at the forefront of computational materials science. At the fundamental and smallest length scale (nm-μm), we developed advanced rate theory and Monte Carlo approaches to model microstructure evolution, non-equilibrium phase transformations, and dislocation-defect interactions. Microscopic and mesoscopic models of radiation hardening, ductile-to-brittle-transition, post-elastic deformation, plastic instabilities, and fracture processes are based on Dislocation Dynamics (DD) and Grain Growth Dynamics (GGD). At the continuum level, we focused on modeling fracture and failure mechanisms for Virtual Integrated Testing (VISTA), and for understanding the limits of both materials-by-design versus structural component design through advancing the new approach of multiscale-multiphysics. The overall research has been strongly coupled with the U.S. national experimental program to ascertain and verify the range of investigated phenomena. In the following, we give a summary of research progress supported by this grant since its inception till November 14, 2017. Detailed research results are available in our publications, listed in the publications section of this report.

36 MATERIALS SCIENCE↗

PyDislocDyn: Code Manual

PyDislocDyn [1] is a suite of python programs designed to perform various calculations for basic research in dislocation dynamics in metals with various crystal symmetries in the continuum limit.

97 MATHEMATICS AND COMPUTING↗