Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distance measure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser beam pointing stabilization using analog position-sensitive diodes

Laser wire scanners have been used for ion beam profile and emittance measurements at the Spallation Neutron Source linear accelerator. Due to propagation distances exceeding 100 m, reliable measurements require laser beam stabilization, previously accomplished with a feedback control loop using a digital camera as a position sensor [Hardin et al., Opt. Express 19, 2874 (2011)]. Here, this paper presents an upgraded pointing stabilization system utilizing analog position-sensitive diodes (PSDs) as the position detector, optimized with an optical diffuser. The new system significantly surpasses the previous system by offering an order-of-magnitude improvement in radiation tolerance and a bandwidth limited only by the burst repetition rate of the laser beam. Operating with a 60-Hz burst mode laser, the new system effectively suppresses laser beam drifts up to 30 Hz, compared to the previous system’s 4 Hz limit. In addition, the amplitude of spectral components below 0.1 Hz was reduced by a factor of more than 100, which is over seven times greater than was achieved by the previous system.

Data acquisition↗
DOE OSTI2020

Adaptive Recovery Model: Designing Systems for Testing Tracing and Vaccination to Support COVID-19 Recovery Planning.

This report documents a new approach to designing disease control policies that allocate scarce testing, contact tracing, and vaccination resources to better control community transmission of COVID19 or similar diseases. The Adaptive Recovery Model (ARM) combines a deterministic compartmental disease model with a stochastic network disease propagation model to enable us to simulate COVID-19 community spread through the lens of two complementary modeling motifs. ARM contact networks are derived from cell-phone location data that have been anonymized and interpreted as individual arrivals to specic public locations. Modeling disease spread over these networks allows us to identify locations within communities conducive to rapid disease spread. ARM applies this model- and data-derived abstractions of community transmission to evaluate the effectiveness of disease control measures including targeted social distancing, contact tracing, testing and vaccination. The architecture of ARM provides a unique capacity to help decision makers understand how best to deploy scarce testing, tracing and vaccination resources to minimize disease-spread potential in a community. This document details the novel mathematical formulations underlying ARM, presents a dynamical stability analysis of the deterministic model components, a sensitivity analysis of control parameters and network structure, and summarizes a process for deriving contact networks from cell-phone location data. An example use case steps through applying ARM to evaluate three targeted social distancing policies using Bernalillo County, New Mexico as an exemplar test locale. This step-by-step analysis demonstrates how ARM can be used to measure the relative performance of competing public health policies. Initial scenario tests of ARM shows that ARMs design focus on resource utilization rather than simple incidence prediction can provide decision makers with additional quantitative guidance for managing ongoing public health emergencies and planning future responses.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Spin waves excitation at micron-sized, anisotropy modified regions in amorphous Fe 80 B 20 stripes: Local properties and inter-regions coupling

We report on the measurement of the local magnetization dynamics occurring, at units of GHz, in large aspect ratio stripes lithographed from reduced damping amorphous Fe 80 B 20 films. The stripes were submitted to local anisotropy modifications by micrometric beam synchrotron X-ray irradiation. Our results include data on the dispersion relationships and group velocities corresponding to spin waves excited at both the non-irradiated and the irradiated regions. Whereas in the former case we observed standing spin waves with transverse-to-the stripe axis wave vector, in the latter one, for which the wave vector of the spin waves was parallel-to-the stripe axis, propagating spin waves were excited. In both regions, we measured the effective propagation distance of the spin waves, which resulted to be independent of the wave vector orientation. In the spin waves excited at the irradiated region, we also measured the decay time and effective damping coefficient, which was in good agreement with previously reported values obtained from FMR measurements in amorphous Fe 80 B 20 continuous films. We show that the interaction of the non-irradiated and irradiated zones results, at the stripe transverse saturation remanence and under an exciting field frequency of 4 GHz, in the introduction of a π phase shift between the standing spin waves excited at both sides of the irradiated region. This result opens the possibility of using the local, transverse to the stripe axis, magnetic anisotropy easy axis induced by the X-ray irradiation as a crucial constituent of a zero-applied field spin wave phase-shifter.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Static metrology of the meter-scale deformable heliostat

This paper describes a heliostat metrology system which is developed based on deflectometry, utilizing a static perforated panel instead of conventional dynamic monitor displays to provide incident rays. The developed method is named static screen deflectometry (SSD). This robust and scalable method is especially valuable for outdoor tests of large reflectors used in concentrating solar-thermal power (CSP) systems. The developed method has been successfully demonstrated on a 2.4 𝑚 × 3.3 𝑚 float glass deformable reflector bent to focus sunlight at 113 𝑚 distance throughout a day. From images obtained from a camera at 50𝑚 distance, the reflector surface was measured to an accuracy of less than 1 𝑚𝑟𝑎𝑑 rms slope error in the full test scope.

14 SOLAR ENERGY↗
DOE OSTI2020

Quantification of defects engineered in single layer MoS 2

Atomic defects are controllably introduced in suspended single layer molybdenum disulfide (1L MoS 2 ) using helium ion beam. Vacancies exhibit one missing atom of molybdenum and a few atoms of sulfur. Quantification was done using a Scanning Transmission Electron Microscope (STEM) with an annular detector. Experimentally accessible inter-defect distance was employed to measure the degree of crystallinity in 1L MoS 2 . A correlation between the appearance of an acoustic phonon mode in the Raman spectra and the inter-defect distance was established, which introduces a new methodology for quantifying defects in two-dimensional materials such as MoS 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Photoinduced Electron-Transfer Distance Is Controlled by the Driving Force in Solid-State Organic Donor-Acceptor Systems

Understanding how short-range electron transfer generates photocurrent in organic solar cells and what photochemical driving force is needed to maximize efficiencies has been an immensely difficult problem. Here we show how these questions are intertwined: the driving force controls the average charge-transfer distance, skipping the shortest-range states in the optimal case. Using photoinduced absorption-detected magnetic resonance, we measure average charge-separation distances in dilute donor–acceptor blends as a function of driving force, and compare these with free charge yields measured by time-resolved microwave conductivity. We find that the largest driving forces show the shortest charge-separation distances, explaining their suppressed free-carrier generation. These results support a long-range electron-transfer model, wherein the driving force controls the initial delocalization of the electron–hole pair. The minimum driving force required for efficient charge separation (and minimal voltage losses) is ultimately set by the dielectric constant of the material.

14 SOLAR ENERGY↗
DOE OSTI2022

Direct measurement of storage and loss behavior in AFM force–distance experiments using the modified Fourier transformation

Force–distance curve experiments are commonly performed in atomic force microscopy (AFM) to obtain the viscoelastic characteristics of materials, such as the storage and loss moduli or compliances. The classic methods used to obtain these characteristics consist of fitting a viscoelastic material model to the experimentally obtained AFM data. Here, we demonstrate a new method that utilizes the modified discrete Fourier transform to approximate the storage and loss behavior of a material directly from the data, without the need for a fit. Additionally, one may still fit a model to the resulting storage and loss behavior if a parameterized description of the material is desired. In contrast to fitting the data to a model chosen a priori, departing from a model-free description of the material's frequency behavior guides the selection of the model, such that the user may choose the one that is most appropriate for the particular material under study. To this end, we also include modified Fourier domain descriptions of commonly used viscoelastic models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Longitudinal coherence and short-term wind speed prediction based on a nacelle-mounted Doppler lidar

The spatial structure of turbulence in atmospheric boundary layer flows is highly relevant to wind energy. In particular, wind turbine control strategies based on inflow preview measurements require knowledge of the longitudinal evolution of turbulent flow as it approaches the rotor. These upstream measurements are usually obtained with nacelle-mounted wind lidars. In contrast to traditional in situ anemometry, lidars collect measurements within a probe volume which varies in size depending on the technology of the commercial system being used. Here, we address two issues related to the use of wind lidar to measure the incoming flow to a wind turbine: (i) whether existing longitudinal coherence models can be used to predict flow at the rotor, based on measurements performed at a distance away from the rotor; and (ii) what effect probe-volume averaging has on the inflow predictions. These two questions are critical to the design and implementation of robust wind turbine control strategies. To address these questions, we perform field measurements and large-eddy simulations to determine which incoming flow structures can be readily predicted with existing coherence models, and which require additional corrections to account for lidar volumetric averaging effects. Results reveal that the wind turbine induction zone has a negligible impact on the longitudinal coherence and first-order turbulence quantities, such as the standard deviation of velocity fluctuations. However, the phase of the signal, from which advection time periods of the turbulent structures are derived, is affected by the rotor blockage effect.

17 WIND ENERGY↗
DOE OSTI2022

Structural heterogeneity in non-crystalline Te x Se1−x thin films

Rapid crystallization behavior of amorphous TexSe1−x thin films limits the use of these alloys as coatings and in optoelectronic devices. Understanding the short- and medium-range ordering of the amorphous structure and the fundamental physics governing the crystallization of the films is crucial. Although the lack of long range crystalline order restricts the characterization of the amorphous films, electron microscopy offers a way to extract information about the nanoscale ordering. In this paper, the local ordering of amorphous TexSe1−x thin films with x=0.22, 0.61, 0.70, 0.90, and 1 grown by thermal evaporation is investigated using radial distribution function (RDF) and fluctuation electron microscopy (FEM) analysis. RDF results show that the nearest-neighbor distances of selenium (Se) and tellurium (Te) in their crystalline structure are preserved, and their bond lengths increase with the addition of Te. Density functional theory (DFT) calculations predict structures with interatomic distances similar to those measured experimentally. Additionally, fluctuations in atomic coordination are analyzed. Medium range order (MRO) analysis obtained from FEM and DFT calculations suggests that there are at least two populations within the chain network structure, which are close to the Se–Se and Te–Te intrachain distances. For the binary alloy with x > 0.61, TexSe1−x, Te–Te like populations increase and Te fragments might form, suggesting that the glass forming ability decreases rapidly.

Sari, Bengisu (ORCID:0000000244217098)↗
DOE OSTI2021

First measurement of large area jet transverse momentum spectra in heavy-ion collisions

Jet production in lead-lead (PbPb) and proton-proton (pp) collisions at a nucleon-nucleon center-of-mass energy of 5.02 TeV is studied with the CMS detector at the LHC, using PbPb and pp data samples corresponding to integrated luminosities of 404 μb$^{−1}$ and 27.4 pb$^{−1}$, respectively. Jets with different areas are reconstructed using the anti-k$_{T}$ algorithm by varying the distance parameter R. The measurements are performed using jets with transverse momenta (p$_{T}$) greater than 200 GeV and in a pseudorapidity range of |η| < 2. To reveal the medium modification of the jet spectra in PbPb collisions, the properly normalized ratio of spectra from PbPb and pp data is used to extract jet nuclear modification factors as functions of the PbPb collision centrality, p$_{T}$ and, for the first time, as a function of R up to 1.0. For the most central collisions, a strong suppression is observed for high-p$_{T}$ jets reconstructed with all distance parameters, implying that a significant amount of jet energy is scattered to large angles. The dependence of jet suppression on R is expected to be sensitive to both the jet energy loss mechanism and the medium response, and so the data are compared to several modern event generators and analytic calculations. The models considered do not fully reproduce the data.[graphic not available: see fulltext]

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

OzDES Reverberation Mapping Program: Hβ lags from the 6-yr survey

ABSTRACT Reverberation mapping measurements have been used to constrain the relationship between the size of the broad-line region and luminosity of active galactic nuclei (AGN). This R–L relation is used to estimate single-epoch virial black hole masses, and has been proposed to use to standardize AGN to determine cosmological distances. We present reverberation measurements made with Hβ from the 6-yr Australian Dark Energy Survey (OzDES) Reverberation Mapping Program. We successfully recover reverberation lags for eight AGN at 0.12 < z < 0.71, probing higher redshifts than the bulk of Hβ measurements made to date. Our fit to the R–L relation has a slope of α = 0.41 ± 0.03 and an intrinsic scatter of σ = 0.23 ± 0.02 dex. The results from our multi-object spectroscopic survey are consistent with previous measurements made by dedicated source-by-source campaigns, and with the observed dependence on accretion rate. Future surveys, including LSST, TiDES, and SDSS-V, which will be revisiting some of our observed fields, will be able to build on the results of our first-generation multi-object reverberation mapping survey.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Joint analysis of 6dFGS and SDSS peculiar velocities for the growth rate of cosmic structure and tests of gravity

ABSTRACT Measurement of peculiar velocities by combining redshifts and distance indicators is a powerful way to measure the growth rate of a cosmic structure and test theories of gravity at low redshift. Here we constrain the growth rate of the structure by comparing observed Fundamental Plane peculiar velocities for 15 894 galaxies from the 6dF Galaxy Survey (6dFGS) and Sloan Digital Sky Survey (SDSS) with predicted velocities and densities from the 2M++ redshift survey. We measure the velocity scale parameter $\beta \equiv {\Omega _{\rm m}^\gamma }/b = 0.372^{+0.034}_{-0.050}$ and $0.314^{+0.031}_{-0.047}$ for 6dFGS and SDSS, respectively, where Ωm is the mass density parameter, γ is the growth index, and b is the bias parameter normalized to the characteristic luminosity of galaxies, L*. Combining 6dFGS and SDSS, we obtain β = 0.341 ± 0.024, implying that the amplitude of the product of the growth rate and the mass fluctuation amplitude is fσ8 = 0.338 ± 0.027 at an effective redshift z = 0.035. Adopting Ωm = 0.315 ± 0.007, as favoured by Planck and using γ = 6/11 for General Relativity and γ = 11/16 for DGP gravity, we get $S_8(z=0) = \sigma _8 \sqrt{\Omega _{\rm m}/0.3} =0.637 \pm 0.054$ and 0.741 ± 0.062 for GR and DGP, respectively. This measurement agrees with other low-redshift probes of large-scale structure but deviates by more than 3σ from the latest Planck CMB measurement. Our results favour values of the growth index γ > 6/11 or a Hubble constant H0 > 70 km s−1 Mpc−1 or a fluctuation amplitude σ8 < 0.8 or some combination of these. Imminent redshift surveys such as Taipan, DESI, WALLABY, and SKA1-MID will help to resolve this tension by measuring the growth rate of cosmic structure to 1 per cent in the redshift range 0 < z < 1.

Said, Khaled↗
DOE OSTI2022

Stellar multiplicity and stellar rotation: insights from APOGEE

ABSTRACT We measure rotational broadening in spectra taken by the Apache Point Observatory Galactic Evolution Experiment (APOGEE) survey to characterize the relationship between stellar multiplicity and rotation. We create a sample of 2786 giants and 24 496 dwarfs with stellar parameters and multiple radial velocities from the APOGEE pipeline, projected rotation speeds vsin i determined from our own pipeline, and distances, masses, and ages measured by Sanders & Das. We use the statistical distribution of the maximum shift in the radial velocities, ΔRVmax, as a proxy for the close binary fraction to explore the interplay between stellar evolution, rotation, and multiplicity. Assuming that the minimum orbital period allowed is the critical period for Roche Lobe overflow and rotational synchronization, we calculate theoretical upper limits on expected vsin i and ΔRVmax values. These expectations agree with the positive correlation between the maximum ΔRVmax and vsin i values observed in our sample as a function of log(g). We find that the fast rotators in our sample have a high occurrence of short-period [log(P/d) ≲ 4] companions. We also find that old, rapidly rotating main-sequence stars have larger completeness-corrected close binary fractions than their younger peers. Furthermore, rapidly rotating stars with large ΔRVmax consistently show differences of 1–10 Gyr between the predicted gyrochronological and measured isochronal ages. These results point towards a link between rapid rotation and close binarity through tidal interactions. We conclude that stellar rotation is strongly correlated with stellar multiplicity in the field, and caution should be taken in the application of gyrochronology relations to cool stars.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Spatially resolved x-ray detection with photonic crystal scintillators

We study the self-collimation phenomenon in photonic crystals (PhC) of wide bandgap materials for ultra-fast and high spatial resolution x-ray detection. We work on various heavy inorganic scintillators: BaF 2 , GaN, ZnO, CsI:Tl, NaI:Tl, LYSO, WO 4 compounds, and plastic scintillators. Conventional scintillator detectors do not rely on a direct detection mechanism; hence, they require intricate design and fabrication processes. We offer a PhC design to observe self-collimation phenomena and overcome the ongoing spatial resolution challenges with these types of materials. We investigate the photonic band diagrams and iso-frequency contours. Fourier transforms based on finite-difference time-domain and frequency domain simulations are done for verifying and analyzing the self-collimation with the selected material. Light extraction efficiency at the PhC–air interface, depending on the truncation distance from the excitation point, is measured. Beam divergence values are calculated at 1 mm propagation distance. The vertical field profiles are obtained to observe the confinement. For the spatial resolution analysis, cross-sectional beam profiles have been examined. Furthermore, Gaussian envelopes are fitted to beam profiles for a consistent data analysis, and full-width-at-half-maximum values are considered. As a result, we theoretically prove and demonstrate the spatially resolved x-ray detection at the sub-micrometer level for a wide range of scintillator materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strong dependence of Type Ia supernova standardization on the local specific star formation rate

As part of an on-going effort to identify, understand and correct for astrophysics biases in the standardization of Type Ia supernovae (SN Ia) for cosmology, we have statistically classified a large sample of nearby SNe Ia into those that are located in predominantly younger or older environments. This classification is based on the specific star formation rate measured within a projected distance of 1 kpc from each SN location (LsSFR). This is an important refinement compared to using the local star formation rate directly, as it provides a normalization for relative numbers of available SN progenitors and is more robust against extinction by dust. We find that the SNe Ia in predominantly younger environments are Δ Y = 0.163 ± 0.029 mag (5.7 σ ) fainter than those in predominantly older environments after conventional light-curve standardization. This is the strongest standardized SN Ia brightness systematic connected to the host-galaxy environment measured to date. The well-established step in standardized brightnesses between SNe Ia in hosts with lower or higher total stellar masses is smaller, at Δ M = 0.119 ± 0.032 mag (4.5 σ ), for the same set of SNe Ia. When fit simultaneously, the environment-age offset remains very significant, with Δ Y = 0.129 ± 0.032 mag (4.0 σ ), while the global stellar mass step is reduced to Δ M = 0.064 ± 0.029 mag (2.2 σ ). Thus, approximately 70% of the variance from the stellar mass step is due to an underlying dependence on environment-based progenitor age. Also, we verify that using the local star formation rate alone is not as powerful as LsSFR at sorting SNe Ia into brighter and fainter subsets. Standardization that only uses the SNe Ia in younger environments reduces the total dispersion from 0.142 ± 0.008 mag to 0.120 ± 0.010 mag. Overall, we show that as environment-ages evolve with redshift, a strong bias, especially on the measurement of the derivative of the dark energy equation of state, can develop. Fortunately, data that measure and correct for this effect using our local specific star formation rate indicator, are likely to be available for many next-generation SN Ia cosmology experiments.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Raster Thomson scattering in large-scale laser plasmas produced at high repetition rate

We present optical Thomson scattering measurements of electron density and temperature in a large-scale (~2 cm) exploding laser plasma produced by irradiating a solid target with a high energy (5-10 J) laser pulse at high repetition rate (1 Hz). The Thomson scattering diagnostic matches this high repetition rate. Unlike previous work performed in single shots at much higher energies, the instrument allows point measurements anywhere inside the plasma by automatically translating the scattering volume using motorized stages as the experiment is repeated at 1 Hz. Measured densities around 4×10 16 cm -3 and temperatures around 7 eV result in a scattering parameter near unity, depending on the distance from the target. The measured spectra show the transition from collective scattering close to the target to non-collective scattering at larger distances. Densities obtained by fitting the weakly collective spectra agree to within 10% with an irradiance calibration performed via Raman scattering in nitrogen.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Enhanced Signal Processing of Distributed Brillouin Fiber Sensors using a Decoupled Radial Basis Function Network

A novel decoupled radial basis function network (D-RBFN) is proposed to accelerate signal processing and address the big data challenges associated with ultra-long distance Brillouin optical time-domain analysis (BOTDA) systems. The proposed frame- work is demonstrated on a dataset measured over a 100 km distance using a bi-directional Raman assisted BOTDA system.

Venketeswaran, Abhishek↗