Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELECTROSTATIC INSTRUMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Plasma Waves Observed in the Cusp Turbulent Boundary Layer: An Analysis of High Time Resolution Wave and Particle Measurements from the Polar Spacecraft

The boundary layer located in the cusp and adjacent to the magnetopause is a region that is quite turbulent and abundant with waves. The Polar spacecraft's orbit and sophisticated instrumentation are ideal for studying this region of space. Our analysis of the waveform data obtained in this turbulent boundary layer shows broadband magnetic noise extending up to a few kilohertz (but less than the electron cyclotron frequency); sinusoidal bursts (a few tenths of a second) of whistler mode waves at around a few tens of hertz, a few hundreds of hertz, and just below the electron cyclotron frequency; and bipolar pulses, interpreted as electron phase-space holes. In addition, bursts of electron cyclotron harmonic waves are occasionally observed with magnetic components. We show evidence of broadband electrostatic bursts covering a range of approx. 3 to approx. 25 kHz (near but less than the plasma frequency) occurring in packets modulated at the frequency of some of the whistler mode waves. On the basis of high time resolution particle data from the Polar HYDRA instrument, we show that these bursts are consistent with generation by the resistive medium instability. The most likely source of the whistler mode waves is the magnetic reconnection site closest to the spacecraft, since the waves are observed propagating both toward and away from the Earth, are bursty, which is often the case with reconnection, and do not fit on the theoretical cold plasma dispersion relation curve.

Pickett, J. S.↗
NASA NTRS1983

Reduction and analysis of data from the plasma wave instruments on the IMP-6 and IMP-8 spacecraft

The primary data reduction effort during the reporting period was to process summary plots of the IMP 8 plasma wave data and to submit these data to the National Space Science Data Center. Features of the electrostatic noise are compared with simultaneous observations of the magnetic field, plasma and energetic electrons. Spectral characteristics of the noise and the results of this comparison both suggest that in its high frequency part at least the noise does not belong to normal modes of plasma waves but represents either quasi-thermal noise in the non-Maxwellian plasma or artificial noise generated by spacecraft interaction with the medium.

Gurnett, D. A.↗
NASA NTRS1979

A rocket-borne data-manipulation experiment using a microprocessor

The development of a data-manipulation experiment using a Z-80 microprocessor is described. The instrumentation is included in the payloads of two Nike Apache sounding rockets used in an investigation of energetic particle fluxes. The data from an array of solid-state detectors and an electrostatic analyzer is processed to give the energy spectrum as a function of pitch angle. The experiment performed well in its first flight test: Nike Apache 14.543 was launched from Wallops Island at 2315 EST on 19 June 1978. The system was designed to be easily adaptable to other data-manipulation requirements and some suggestions for further development are included.

Davis, L. L.↗
NASA NTRS1986

First plasma wave observations of Uranus

Plasma wave data collected by instrumentation on Voyager 2 as it passed Uranus magnetosphere are discussed. Radio signals at 31.1 and 56.2 kHz were detected 5 days from closest approach and were buried in a burst of electrostatic noise as the spacecraft crossed the bow shock 10 hr before closest approach. The noise arose from electrons escaping the bow shock into the solar wind. Electric field intensities downstream of the shock were reduced, a situation similar to those observed around Saturn and Jupiter. Whistler-mode hiss and chorus emissions were prominent within the magnetosphere at less than 8 Uranus radii, a region where particle detectors registered intense energetic electron fluxes. Also, micron-sized particle impacts at a rate of 30-50 impacts/sec occurred when passing through the ring plane. The duration of the micro-impact phase was sufficient to estimate the ring thickness as about 4000 km.

Gurnett, D. A.↗
NASA NTRS1995

Mechanism for generation of 2-3 kHz radiation in the outer heliosphere

The question of how low-frequency non-thermal radio emissions at the boundary of the heliosphere might be generated is considered. The mechanism consists of two steps. First, the beam of energetic electrons generates a high level of electrostatic Langmuir plasma waves. Second, electromagnetic radiation results from the non-linear interaction between Langmuir waves. Intensity of radio emissions at 2 to 3 kHz detected by the Voyager plasma wave instrument in the outer heliosphere can be explained provided that the electron beams generating Langmuir waves exist also in the postshock plasma due to secondary shocks in the compressed solar wind beyond the termination shock. Modification of the heliospheric shocks by the cosmic ray pressure is also taken into account. The field strengths of Langmuir waves required to generate the second harmonic emissions are of 50 to 100 microvolts per meter. These waves may be observed in situ by Voyager 1 and 2 in the near future.

Macek, W. M.↗
NASA NTRS2013

Development of a Real Time Internal Charging Tool for Geosynchronous Orbit

The high-energy electron fluxes encountered by satellites in geosynchronous orbit pose a serious threat to onboard instrumentation and other circuitry. A substantial build-up of charge within a satellite's insulators can lead to electric fields in excess of the breakdown strength, which can result in destructive electrostatic discharges. The software tool we've developed uses data on the plasma environment taken from NOAA's GOES-13 satellite to track the resulting electric field strength within a material of arbitrary depth and conductivity and allows us to monitor the risk of material failure in real time. The tool also utilizes a transport algorithm to simulate the effects of shielding on the dielectric. Data on the plasma environment and the resulting electric fields are logged to allow for playback at a variable frame rate.

Posey, Nathaniel A.↗
NASA NTRS1986

The dynamics of charged dust in the tail of Comet Giacobini-Zinner

A numerical simulation has been performed to calculate the distributions of dust particles of various sizes down the tail of comet P/Giacobini-Zinner. When the electrostatic charging of the grains in the plasma and radiative environment of the comet is taken into account, it is found that the distribution of the grains (particularly at the lowest end of the mass spectrum) in a plane normal to the orbital plane is entirely different from what is expected had the grains been uncharged. Although the NASA-ICE spacecraft, which will fly through the tail of this comet almost normal to its orbital plane on September 11, 1985, has no dedicated dust experiments, it is expected that the plasma wave instrument will serve as an indirect detector, even of the smallest grains, via the plasma clouds created by the high-velocity dust impacts. Knowledge of the spatial variation of the grain sizes encountered along the flight path of the spacecraft will provide us with the information necessary to calculate the electrostatic potential of the grains, which in turn will lead to an estimation of the role of the electromagnetic forces on the dynamics of such grains.

Horanyi, M.↗
NASA NTRS1988

Plasma waves associated with diffuse auroral electrons at mid-altitudes

Using simultaneous observations from the DE-1 High-Altitude Plasma Instrument and the Plasma Wave Instrument, a study is made of 28 auroral-zone crossings, equally divided among dayside and nightside cases covering a range of Kp values from 1- to 8. In the diffuse auroral region, electrostatic emissions of frequencies up to a few kHz are associated with low-energy field-aligned electron beams. Of 18 cases (11 nightside; 7 dayside) examined at high resolution in the particle data, 15 (9 nightside; 6 dayside) exhibited field-aligned beams with electrostatic waves. In most cases, the beams were upward-directed, but occasionally they traveled both up and down the field line. The electrostatic emissions are interpreted as electron-acoustic waves excited by the field-aligned beams.

Sharber, J. R.↗
NASA NTRS2004

Thermal-Stress Control of Microshutter Arrays in Cryogenic Applications for the James Webb Space Telescope

We report on methods to minimize thermally-induced deformation in a MEMS-based reconfigurable aperture. The device is an enabling component of the Near-Infrared Spectrometer, a principle instrument on NASA's James Webb Space Telescope. The Microshutter Array consists of 384 x 175 individually addressable shutters which can be magnetically rotated 90 deg into the plane of the array and electrostatically latched open. Each shutter is a 100 x 200 micron rectangular membrane suspended by a small neck region and torsion flexure. The primary materials in the shutter are a 5000A Si3N4 layer for mechanical rigidity, 2000A Al for opacity and electrostatic latching, and 2800A CoFe for magnetic actuation. This multi-layer stack presents a challenge due to the operating temperatures required for the device: both room temperature (300K) and cryogenic temperature (35K). Thermal expansion of the materials causes the shutters to bow out of plane excessively, which can prevent actuation of the shutters, cause damage to portions of the array, and allow light leakage around closed shutters. Here we present our investigation of several methods to prevent microshutter bowing including deposition of additional materials on the shutters to create a symmetrical layer stack and replacing the current stack with low-coefficient of thermal expansion materials. Using shutter-size suspended cantilever beams as a rapid-development test bed, we have reduced out-of-plane bowing between 300K and 35K to 10% or better. We are currently applying these results to microshutter arrays to develop shutters that remain flat from room temperature to cryogenic temperature while retaining the required mechanical, optical, and magnetic properties.

Kelly, Daniel P.↗
NASA NTRS2018

Evidence for Arcing on the International Space Station Solar Arrays

The International Space Station (ISS) is powered by a set of 160 V photovoltaic arrays (PVA) in the US sector. Arcing thresholds for the ISS PVAs measured in the laboratory are shown to vary from -210 V to -457 V depending on the ambient plasma density, where low arcing threshold occurs at high plasma densities. Arcing of ISS PVAs on-orbit is unlikely under normal operating conditions. The net potential of a solar cell relative to space depends on the position of the cell within a string, the (vxB)•L contribution to the potential at the location of the cell, and the frame potential of ISS due to solar array charging. Net potentials on a cell will reach the arcing threshold only on rare occasions. However, the situation changes when damaged PVA strings are considered. Open circuit strings can exhibit voltages exceeding -300 V when the strings are shunted. Under these conditions the local potential on the damaged string can easily exceed arcing thresholds at the low end of the -210 V to -457 V range for ISS PVAs. Because arcing to space on the array will remove some fraction of the net negative charge on the ISS, transient variations in the frame potential are expected during the electrostatic discharge events. We report a new class of transient ISS frame potential variations consistent with arcing on open strings using data from the ISS Floating Potential Measurement Unit’s Floating Potential Probe instrument.

Minow, Joseph I.↗
NASA NTRS1983

Development of a miniature scanning electron microscope for in-flight analysis of comet dust

A description is presented of an instrument which was developed with the original goal of being flown on the International Comet Mission, scheduled for a 1985 launch. The Scanning Electron Microscope and Particle Analyzer (SEMPA) electron miniprobe is a miniaturized electrostatically focused electron microscope and energy dispersive X-ray analyzer for in-flight analysis of comet dust particles. It was designed to be flown on board a comet rendezvous spacecraft. Other potential applications are related to asteroid rendezvous and planetary lander missions. According to the development objectives, SEMPA miniprobe is to have the capability for imaging and elemental analysis of particles in the size range of 0.25 microns and larger.

Conley, J. M.↗
NASA NTRS1999

Electro-Active Polymer (EAP) Actuators for Planetary Applications

NASA is seeking to reduce the mass, size, consumed power, and cost of the instrumentation used in its future missions. An important element of many instruments and devices is the actuation mechanism and electroactive polymers (EAP) are offering an effective alternative to current actuators. In this study, two families of EAP materials were investigated, including bending ionomers and longitudinal electrostatically driven elastomers. These materials were demonstrated to effectively actuate manipulation devices and their performance is being enhanced in this on-going study. The recent observations are reported in this paper, include the operation of the bending-EAP at conditions that exceed the harsh environment on Mars, and identify the obstacles that its properties and characteristics are posing to using them as actuators. Analysis of the electrical characteristics of the ionomer EAP showed that it is a current driven material rather than voltage driven and the conductivity distribution on the surface of the material greatly influences the bending performance. An accurate equivalent circuit modeling of the ionomer EAP performance is essential for the design of effective drive electronics. The ionomer main limitations are the fact that it needs to be moist continuously and the process of electrolysis that takes place during activation. An effective coating technique using a sprayed polymer was developed extending its operation in air from a few minutes to about four months. The coating technique effectively forms the equivalent of a skin to protect the moisture content of the ionomer. In parallel to the development of the bending EAP, the development of computer control of actuated longitudinal EAP has been pursued. An EAP driven miniature robotic arm was constructed and it is controlled by a MATLAB code to drop and lift the arm and close and open EAP fingers of a 4-finger gripper. Keywords: Miniature Robotics, Electroactive Polymers, Electroactive Actuators, EAP Materials

Bar-Cohen, Y.↗
NASA NTRS1983

Warm fog dispersal

The charged particle generator was further tested after some design modification. The generator performance was measured with additional instrumentation and found to confirm previous measurements. Plans for a field testing were than developed. The overall status of the program and the field test plans were presented to a group of atmospheric scientists and electrostatic experts at the NASA/MSFC sponsored USRA Workshop on Electrostatic Fog Dispersal at NCAR, Boulder, Colorado discussed in previous sections. The recommendations from this workshop are being evaluated as to whether NASA should proceed with the field test or whether further theoretical research on the phenomenon of electrostatic fog dispersal and additional development of the charged particle generator should be carried out. Information obtained from the USRA Workshop clearly identified three physical mechanisms that could possibly influence the fog dispersal process, which heretofore have not been considered, and which may provide additional insight to the direction of further fog dispersal work. These mechanisms are: the effect of corona discharge on the electric field strength at the surface, the influx of fog into the cleared volume by turbulent diffusion, and the increase in supersaturation as liquid water is removed, activating haze particles, and thus generating more fog. Plans are being formulated to investigate these mechanisms.

Frost, W.↗
NASA NTRS2020

Comparison of Extreme Value Distributions for Electrostatic Discharge Magnitudes in Spacecraft Charging Tests

Electrostatic Discharge (ESD) induced by the accumulation of charge in the space environment is known to cause spacecraft anomalies and failures. While it is critical to estimate the worst-case expected ESD, sensitive radar instruments can be impacted by high rates of occurrence of very small ESD. To estimate the correct extreme behavior, it is important to select the correct extreme value distribution for extrapolation of test results limited in time and sensitivity. Quantile-quantile (Q-Q) analysis is used to compare electron beam-induced ESD test data to several statistical distributions used in the published literature. The best-fit distribution is shown to vary from between tests on different materials; however, it is clear that power law distributions are not good approximations for low amplitude events. Q-Q analysis is a convenient graphical method for evaluating multiple theoretical extreme-value distributions simultaneously.

Kim, Wousik↗
NASA NTRS1986

Environment-induced electrostatic discharges as the cause of Voyager 1 power-on resets

The Pioneer and Voyager spacecraft all experienced anomalous behavior during their encounters with Jupiter. In particular, the Voyager 1 spacecraft experienced 42 electrical circuitry designed to protect the on-board computer from power fluctuations. Given the diversity of instrumentation and frequency of the anomalies observed by Voyager 1 in the inner magnetosphere of Jupiter, this set of data is particularly well suited as a case study. Although the nature of the anomalies clearly indicates a spacecraft-charging origin, the Voyager low-energy plasma data apparently imply absolute surface potentials of only a few tens of volts. It is thus difficult to explain the anomalies in terms of surface charging. The anomalies are, however, shown to be consistent with the hypothesis of internal charging of spacecraft parts and components.

Leung, P.↗
NASA NTRS1985

Comparison of polar cap potential drops estimated from solar wind and ground magnetometer data - CDAW 6

It is pointed out that the maximum electrostatic potential difference across the polar cap, Phi, is a fundamental measure of the coupling between the solar wind and the earth's magnetosphere/ionosphere sytem. During the Coordinated Data Analysis Workshop (CDAW) 6 intervals, no suitably instrumented spacecraft was in an appropriate orbit to determine the polar-cap potential drop directly. However, two recently developed independent techniques make it possible to estimate the polar-cap potential drop for times when direct spacecraft data are not available. The present investigation is concerned with a comparison of cross-polar-cap potential drop estimates calculated for the two CDAW 6 intervals on the basis of these two techniques. In the case of one interval, the agreement between the potential drops and Joule heating rates is relatively good. In the second interval, however, the agreement is not very good. Explanations for this discrepancy are discussed.

Reiff, P. H.↗
NASA NTRS1990

Spacelab-3 low-g accelerometer data from the fluid experiments system (FES)

The Fluids Experiment System (FES) flown aboard Spacelab 3 contained a Miniature Electrostatic Accelerometer (MESA). This accelerometer was purchased from Bell Aerospace, Textron and had three range (auto switching), bidirectional, three orthogonal axis capability. BGB, Inc. is in the process of examining the total mission data from this instrument. From these data, areas of interest are identified and related back to mission events. The basic format of the data for the total mission is root mean square (RMS), with two hours per plot.

Arnett, Gary↗