SEARCH · Search NASA

Results for “Epoxy Resins”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Study of low-cost fabrication methods for aerospace composite materials

Flat and hat section specimens of graphite/epoxy composite materials have been fabricated by the resin bath or wet pultrusion process. This demonstrated the feasibility of incorporating crossplied graphite fiber reinforcements in conjunction with epoxy resin systems in the wet pultrusion process. However, the thickness constraints of the pultrusion process, the lack of dimensional stability of the crossply materials and equipment limitations affect the quality of the hat section pultrusions. The wet pultrusion process shows promise of being a low cost method for producing composite parts with constant cross section along the length. A cost analysis showed at least 80 percent cost reduction for the hat section and 40 percent for flat panel by pultrusion over the conventional manual and automated lay-up.

Chung, H. H.↗

DOE OSTI2025

Using low cost, bio-derived and recycled materials in advanced scalable small- and medium- wind turbine manufacturing

In partnership with Bergey Windpower, this project explored the use of recyclable and recycled materials in small- to medium-wind turbine blades (WTBs). A recyclable epoxy resin and infusible thermoplastic resin were investigated using identical fiber reinforcements and manufacturing practices used as Bergey, and the substitution of continuous virgin glass fiber (GF) layers with recycled nonwoven GF (rGF, NW) mats was trialed. The alternative resins both showed very promising performance in terms of static tensile and flexural behavior as well as thermal properties and fatigue behavior in comparison with that of the incumbent materials used at Bergey. The NW rGF materials, however, were found to be a poor substitute for the continuous GF materials for two primary reasons. Firstly, the NW mats took up significantly more resin than their continuous counterparts, which would increase both the weight and the cost of the WTBs. Additionally, an unexpected reaction occurred between the rGF and epoxy materials that resulted in a highly porous, foamed structure. The foaming phenomenon was not observed with the rGF NW and infusible thermoplastic material, but the resin uptake was still prohibitively high. Based on the results of this study, recyclable infusible resins could be viable candidate materials for Bergey in the future. The foaming reaction with the rGF NW mats could prove highly useful in other applications requiring structural foams and has been used to produce demonstrative sandwich panels.

17 WIND ENERGY↗

NASA NTRS1993

Crushable Washers For Bolting Composite Panels

Crushable washers proposed for use in protecting composite-material (matrix/fiber) panels against overloads applied by nut-and-bolt fasteners. Intended for use at drilled holes, where strengths of composite panels reduced by exposure of ends of fibers. Washer consists of metal skin filled with microcapsules of epoxy resin and hardener. Alternatively, filled with fibers collapsing under given load. Crushing action simultaneously fractures microcapsules (if used), releasing components of epoxy. These components mix and fill bolthole and fiber-reinforcement interstices. Epoxy then hardens, locking fasteners in place.

Daech, Alfred F.↗

NASA NTRS1982

Nonequilibrium material effects on the behavior of polymeric composite matrices and their related composites

The effects of physical aging on the material properties of some linear and network macromolecular glasses are discussed. The free volume concept is used to describe this behavior. The effect of physical aging on properties of some uniaxial graphite/fiber epoxy resin composites is investigated using stress relaxation in both tensile and flexural modes. The matrix polymers used were resins both of which are based on a 4,4-methylenedianiline derivative of epichlorohydrin with diamino diphenyl sulfone (DDS) as the curing agent. The matrix resin, as used in the practical application in composites, not fully cured and the glass transition of the network was dependent on the curing schedule. The physical aging of the bulk crosslinked epoxy was found to depend on the annealing temperature, and the T sub g of the resin. The physical aging of the composite, monitored by the stress relaxation method, was found to be dependent on the testing direction.

Wilkes, G. L.↗

NASA NTRS1985

Electron emission and acoustic emission from the fracture of graphite/epoxy composites

In past studies it has been shown that the fracture of materials leads to the emission of a variety of species, including electrons, ions, neutral molecules, and photons, all encompassed by the term 'fractoemission' (FE). In this paper, electron emission (EE) from the fracture of single graphite fibers and neat epoxy resin is examined. Measurements of EE are also combined with the detection of acoustic emission (AE) during the testing of graphite-epoxy composite specimens with various fiber orientation. The characteristics of these signals are related to known failure mechanisms in fiber-reinforced plastics. This study suggests that by comparing data from AE and FE measurements, one can detect and distinguish the onset of internal and external failure in composites. EE measurements are also shown to be sensitive to the locus of fracture in a composite material.

Dickinson, J. T.↗

NASA NTRS2003

VARTM Process Modeling of Aerospace Composite Structures

A three-dimensional model was developed to simulate the VARTM composite manufacturing process. The model considers the two important mechanisms that occur during the process: resin flow, and compaction and relaxation of the preform. The model was used to simulate infiltration of a carbon preform with an epoxy resin by the VARTM process. The model predicted flow patterns and preform thickness changes agreed qualitatively with the measured values. However, the predicted total infiltration times were much longer than measured most likely due to the inaccurate preform permeability values used in the simulation.

Song, Xiao-Lan↗

NASA NTRS1980

Engine environmental effects on composite behavior

The effects of turbojet engine environmental saturation moisture and temperatures up to 300 F on composites were investigated. It was found that epoxy resin composites absorbed the most moisture (2 wt %), while polyimide resin composites absorbed 0.8%. High moisture and 250 F degraded the flexular and interlaminar shear properties, and the environmental and impact conditions severely damaged epoxy composites. The impact damage of fiber composites in moisture-temperature environments can be assessed with finite element and composite mechanics analyses. Engine operation environmental conditions of 0.8% moisture and 140 F had no discernible effect on the fatigue resistance of composite fan exit guide vanes, which can be designed to exceed engine operational requirements using composite materials.

Chamis, C. C.↗

NASA NTRS1973

Large boron--epoxy filament-wound pressure vessels

Advanced composite material used to fabricate pressure vessel is prepeg (partially cured) consisting of continuous, parallel boron filaments in epoxy resin matrix arranged to form tape. To fabricate chamber, tape is wound on form which must be removable after composite has been cured. Configuration of boron--epoxy composite pressure vessel was determined by computer program.

Jensen, W. M.↗

NASA NTRS1984

Variation of Resin Properties Through the Thickness of Cured Samples

It is the purpose of this work to gain knowledge of the glassy materials used as matrices in composites and to study the homogeneity resulting from the curing process. An attempt is made to link the glass transition quantitatively with the presence of a given material. Expoxy resins containing various amounts of hardener (TGDDM/DDS system) were cured in a muffle furnace at 473 K for seven hours. The glass transition temperature, T sub g versus weight minus percent of hardener in the epoxy resin were measured. A limit was rapidly reached in T sub g at only two percent hardener. Thus, the glass transition of the fully cured epoxy-amine matrix seems not much different from the epoxide-epoxide cure. The T sub g versus cure-time for the epoxide-epoxide reaction was also studied. My 720 was cured by itself in an oil bath at 473 K for different lengths of time. The T sub g was found to increase exponentially with the cure time, and a maximum T sub g of about 450 K was reached after eleven hours. The reaction was found to be inhibited by running the sample under argon.

Source record↗

NASA NTRS1985

Mechanical properties testing of candidate polymer matrix materials for use in high performance composites

The mechanical properties of four candidate neat resin systems for use in graphite/epoxy composites are characterized. This includes tensile and shear stiffnesses and strengths, coefficients of thermal and moisture expansion, and fracture toughness. Tests are conducted on specimens in the dry state and moisture-saturated, at temperatures of 23C, 82C and 121C. The neat resins tested are Hexcel HX-1504, Narmco 5245-C, American Cyanamid CYCOM 907, and Union Carbide ERX-4901A (MDA). Results are compared with those obtained for four other epoxy resins tested in a prior program, i.e., Hercules 3502, 2220-1, and 2220-3, and Ciba-Geigy Fibredux 914, as well as with available Hercules 3501-6 data. Scanning electron microscopic examination of fracture surfaces is performed to permit the correlation of observed failure modes with the environmental test conditions. A finite element micromechanics analysis is used to predict unidirectional composite response under various test conditions, using the measured neat resin properties as input data.

Zimmerman, R. S.↗

NASA NTRS2010

Epoxy/Glass and Polyimide (LaRC(TradeMark) PETI-8)/Carbon Fiber Metal Laminates Made by the VARTM Process

Cano, Roberto J.↗

NASA NTRS1992

Novel matrix resins for composites for aircraft primary structures, phase 1

The objective of the contract is the development of matrix resins with improved processability and properties for composites for primarily aircraft structures. To this end, several resins/systems were identified for subsonic and supersonic applications. For subsonic aircraft, a series of epoxy resins suitable for RTM and powder prepreg was shown to give composites with about 40 ksi compressive strength after impact (CAI) and 200 F/wet mechanical performance. For supersonic applications, a thermoplastic toughened cyanate prepreg system has demonstrated excellent resistance to heat aging at 360 F for 4000 hours, 40 ksi CAI and useful mechanical properties at greater than or equal to 310 F. An AB-BCB-maleimide resin was identified as a leading candidate for the HSCT. Composite panels fabricated by RTM show CAI of approximately 50 ksi, 350 F/wet performance and excellent retention of mechanical properties after aging at 400 F for 4000 hours.

Woo, Edmund P.↗

NASA NTRS1979

Development of aircraft lavatory compartments with improved fire resistance characteristics. Phase 2: Sandwich panel resin system development

A NASA-funded program is described which aims to develop a resin system for use in the construction of lavatory wall panels, sidewall panels, and ceiling panels possessing flammability, smoke and gas emission, and toxicity (FS&T) characteristics superior to the existing epoxy resin. Candidate resins studied were phenolic, polyimide, and bismaleimide. Based on the results of a series of FS&T as well as mechanical and aesthetic property tests, a phenolic resin was chosen as the superior material. Material and process specifications covering the phenolic resin based materials were prepared and a method of rating sandwich panel performance was developed.

Anderson, R. A.↗

NASA NTRS1987

Fabrication and characterization of amine terminated poly(arylene ether sulfone) modified epoxy-carbon fiber composites

Multifunctional epoxy resin networks were chemically modified with thermoplastic amine terminated poly(arylene ether sulfones) of controlled molecular weights. This system was then examined as both neat resin and as a matrix resin for carbon fiber composites. The neat resin displayed a significant increase in both fracture toughness and energy release rate values. This was attributed to the altered morphology, which could be varied from particles of polysulfone in an epoxy matrix to that of a quasi-continuous polysulfone phase.

Cecere, James A.↗

NASA NTRS2004

High Temperature VARTM with LaRC Polyimides

Recent work at NASA Langley Research Center (LaRC) has concentrated on developing new polyimide resin systems for advanced aerospace applications that can be processed without the use of an autoclave. Polyimide composites are very attractive for applications that require a high strength to weight ratio and thermal stability. Vacuum assisted resin transfer molding (VARTM) has shown potential to reduce the manufacturing cost of composite structures. In VARTM, the fibrous preform is infiltrated on a rigid tool surface contained beneath a flexible vacuum bag. Both resin injection and fiber compaction are achieved under pressures of 101.3 KPa or less. Recent studies have demonstrated the feasibility of the VARTM process for fabrication of void free structures utilizing epoxy resin systems with fiber volume fractions approaching 60%. In this work, the VARTM process has been extended to the fabrication of composite panels from polyimide systems developed at the Langley Research Center. This work has focused on processing LARC(trademark) PETI-8 (Langley Research Center Phenylethynyl Terminated Imide- 8), an aromatic polyimide based on 3,3',4,4' -biphenyltetracarboxylic dianhydride, a 50:50 molar ratio of 3,4'-oxydianiline and 1,3-bis(3-aminophenoxy)benzene, with 4-phenylethynylphthalic anhydride as the endcapping agent. Various molecular weight versions were investigated to determine their feasibility of being processed by VARTM at elevated temperatures. An injection temperature of approximately 280 C was required to achieve the necessary viscosity (<5 Poise) for flow at VARTM pressures. Laminate quality and initial mechanical properties are presented for LARC(trademark) PETI-8 and 6k IM7 uniweave fabric.

Cano, Roberto J.↗

NASA NTRS1986

Effects of high energy radiation on the mechanical properties of epoxy/graphite fiber reinforced composites

The epoxy resin system formed by tetraglycidyl 4,4'-diamino diphenyl methane (TGDDM) and 4,4'-diamino diphenyl sulfone (DDS) was characterized by dynamic mechanical analysis and differential scanning calorimetry. Dynamic mechanical properties of graphite fiber epoxy composite specimens formulated with two different adhesive systems (NARMCO 5208, NARMCO 5209) were determined. The specimens were exposed to varying dose levels of ionizing radiation (0.5 MeV electrons) with a maximum absorbed dose of 10,000 Mrads. Following irradiation, property measurements were made to assess the influence of radiation on the epoxy and composite specimens. The results established that ionizing radiation has a limited effect on the properties of epoxy and composite specimens.

Fornes, R. E.↗

NASA NTRS1983

Removal of histological sections from glass for electron microscopy - Use of Quetol 651 resin and heat

A number of approaches have been used to separate stained conventional histological sections from glass slides in preparation for a study with the electron microscope. However, in each reported case some problems were encountered with respect to the separation process. The present investigation is concerned with the use of the epoxy resin Quetol 651 as an embedding medium for this procedure, taking into account the simple application of heat (62-64 C) for performing the separation step. After the tissue has been removed from the glass by the considered technique, it is thin sectioned, and stained with uranyl acetate-lead citrate.

Kraft, L. M.↗

NASA NTRS2002

Dimensional Stability of Complex Shapes Manufactured by the VARTM Process

The vacuum assisted resin transfer molding (VARTM) process is a cost effective, innovative method that is being considered for manufacture of large aircraft-quality components where high mechanical properties and dimensional tolerance are essential. In the present work, carbon fiber SAERTEX fabric/SI-ZG-5A epoxy resin C-shaped laminates were manufactured by VARTM using different cure cycles followed by the same post-cure cycle. The final part thickness was uniform except at the corner were thinning was observed. The cure cycle selected is shown to significantly affect the part spring-in and a long cycle at 66 C followed by a 178 C post-cure produced a part with negligible spring-in.

Hubert, Pascal↗