SEARCH · Search NASA

Results for “FAILURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Detection by pilots of system failures during instrument landings

The effects of gust disturbances and the pilot's participation mode in the control task on his work-load level and failure detection performance during a simulated low visibility landing approach are examined. We found that the participation mode had a strong effect on the pilot's work load, the induced work load being lowest when the pilot acted as a monitoring element during a coupled approach and highest when the pilot was an active element in the control loop. The effects of differential work load and participation mode on failure detection were separated. The participation mode was shown to have a dominant effect on the failure detection performance, with a failure in a monitored (coupled) axis being detected significantly faster than a comparable failure in a manually controlled axis.

Ephrath, A. R.↗

NASA NTRS1979

Space Shuttle Solid Rocket Booster Decelerator Subsystem Drop Test 3 - Anatomy of a failure

A test failure dramatically points out a design weakness or the limits of the material in the test article. In a low budget test program, with a very limited number of tests, a test failure sparks supreme efforts to investigate, analyze, and/or explain the anomaly and to improve the design such that the failure will not recur. The third air drop of the Space Shuttle Solid Rocket Booster Recovery System experienced such a dramatic failure. On air drop 3, the 54-ft drogue parachute was totally destroyed 0.7 sec after deployment. The parachute failure investigation, based on analysis of drop test data and supporting ground element test results is presented. Drogue design modifications are also discussed.

Runkle, R. E.↗

NASA NTRS1980

Failure prediction techniques for compression loaded composite laminates with holes

The degree of notch sensitivity of composites in compression and whether their failures can be predicted over a wide range of plate and hole sizes. The notch sensitivity of composites is investigated by comparing actual failure loads of laminates with circular holes, with the extreme failure that would be expected from an ideal notch insensitive material and from an ideal notch sensitive material. The predictability question is addressed by applying the point stress failure criterion to a wide range of plate widths and hole sizes and comparing with available experimental data. The severity of impact is explored by comparing strength reductions resulting from impact with those resulting from comparable size circular holes. Finally, comparison is made of the differences to be expected from the effects of cracks and circular holes on failure strength.

Mikulas, M. M., Jr.↗

NASA NTRS1980

Study of intermittent field hardware failure data in digital electronics

The collection and analysis of data concerning intermittent dailures in digital devices was performed using data from a computer design for shipboard usage. The failure data consisted of actual field failures classified by failure mechanisms and their likelihood of having been intermittent, potentially intermittent, or hard. Each class was studies with respect to computer operation in the ranges of 0 to 2,000 hours, 0 to 5, hours, and 0 to 10,000 hours. The study was done at the computer level as well as the microcircuit level. Results indicate that as age increases, the quasi-intermittent failure rate increases and the mean time to failure descreases.

Oneill, E. J.↗

NASA NTRS1979

Failure analysis of composite laminates with free edges

Linear elastic stress distributions obtained from a refined finite element mesh are used in conjunction with the tensor polynomial failure criterion to predict the initiation of failure in symmetric, finite-width graphite-epoxy laminates under tensile loading. Results are presented for a wide variety of laminates including: (+ and - theta)s angle-ply; cross-ply (0/90)s and (90/0)s; and quasi-isotropic (90/0/+ and - 45)s and (+ and -45/0/90)s. It is shown that the elastic stress distributions generally compare favorably with other published results, but also indicate improved satisfaction of the stress-free boundary conditions and indicate some differences in the singular behavior of selected stress components at the free edge. The tensor polynomial failure criterion is used to predict the location and mode of first failure. Examination of the individual terms of the polynomial indicates different modes of failure depending upon the laminate configuration.

Herakovich, C. T.↗

NASA NTRS1980

On failure modes in finite width angle ply laminates

The results of a failure analysis of finite width (+ or - theta)s T300/5208 graphite-epoxy laminates subjected to thermal curing loads and applied tensile strain are presented. Stress distributions obtained from linear elastic and linear thermoelastic finite element stress analyses are used in conjunction with the tensor polynomial failure criterion to predict the mode and location of first failure in laminates with fiber angles ranging from five to seventy-five degrees. It is shown that the mode of failure is predominantly interlaminar shear for small fiber angles, shifts to combined interlaminar normal, in-plane shear and in-plane normal for intermediate angles, and is primarily transverse tension for large fiber angles. The location of initial failure shifts from the (+ or - theta)s interface for small fiber angles to the midplane for large fiber angles.

Herakovich, C. T.↗

NASA NTRS1982

STS-3 main parachute failure

A failure analysis of the parachute on the Space Transportation System 3 flight's solid rocket booster's is presented. During the reentry phase of the two Solid Rocket Boosters (SRBs), one 115 ft diameter main parachute failed on the right hand SRB (A12). This parachute failure caused the SRB to impact the Ocean at 110 ft/sec in lieu of the expected 3 parachute impact velocity of 88 ft/sec. This higher impact velocity relates directly to more SRB aft skirt and more motor case damage. The cause of the parachute failure, the potential risks of losing an SRB as a result of this failure, and recommendations to ensure that the probability of chute failures of this type in the future will be low are discussed.

Runkle, R.↗

NASA NTRS1981

The compressive failure of graphite/epoxy plates with circular holes

The results of an experimental investigation of the compressive behavior of T300/5203 graphite/epoxy laminated plates measuring 127.0 by 254.0 mm and containing circular holes ranging to 38.1 mm are reported. Two thicknesses, 24-ply and 48-ply, were chosen to differentiate between stability failures resulting from buckling and strength failures caused by the hole. Both quasi-isotropic and orthotropic stacking arrangements were used. The critical buckling load of the 24-ply panels was independent of hole size. Bifurcation occurred in the two half-wave mode longitudinally and one half-wave mode laterally in the quasi-isotropic panels. For the orthotropic 24-ply panels, bifurcation began in the one half-wave mode shape in each direction, but changed to the two half-wave mode before failure. Consistent post-buckling strength was exhibited by both laminated configurations. Panels with hole diameters below 3.175 mm displayed buckling before failure; those with holes larger than 6.35 mm experienced material failure around the hole before panel collapse.

Knauss, J. F.↗

NASA NTRS1982

Rotor fragment protection program: Statistics on aircraft gas turbine engine rotor failures that occurred in US commercial aviation during 1979

Statistical information relating to the number of gas turbine engine rotor failures which occurred during 1979 in commercial aviation service use is provided. The predominant failure mode involved blade fragments, 84 percent of which were contained. No uncontained disk failures occurred and although fewer rotor rim and seal failures occurred, 100 percent and 50 percent, respectively, were uncontained. Sixty-eight percent of the 157 rotor failures occurred during the take-off and climb stages of flight.

Delucia, R. A.↗

NASA NTRS1983

Failure analysis of composite laminates including biaxial compression

This report describes a continued effort on the development and application of the tensor polynomial failure criterion for composite laminate analysis. In particular, emphasis is given to the design, construction and testing of a cross-beam laminate configuration to obtain "pure' biaxial compression failure. The purpose of this test case was to provide to permit "closure' of the cubic form of the failure surface in the 1-2 compression-compression quadrant. This resulted in a revised set of interaction strength parameters and the construction of a failure surface which can be used with confidence for strength predictions, assuming a plane stress state exists. Furthermore, the problem of complex conjugate roots which can occur in some failure regions is addressed and an "engineering' interpretation is provided. Results are presented illustrating this behavior and the methodology for overcoming this problem is discussed.

Tennyson, R. C.↗

NASA NTRS1984

Compression failure mechanisms in unidirectional composites

Compression failure mechanisms in unidirectional composites were examined. Possible failure modes of constituent materials are summarized and analytical models for fiber microbuckling are reviewed from a unified viewpoint. Due to deficiencies in available models, a failure model based on nonlinear properties and initial fiber curvature is proposed. The effect of constituent properties on composite compression behavior was experimentally investigated using two different graphite fibers and four different epoxy resins. The predominant microscopic scale failure mode was found to be shear crippling. In a soft resin, shear crippling was in the form of buckling of fibers on a microscopic scale. However, stiff resins failure was characterized by the formation of a kink band. For unidirectional laminates, compressive strength, and compressive modulus to a less extent, were found to increase with increasing magnitude of resin modulus. The change in compressive strength with resin modulus was predicted using the proposed nonlinear model.

Hahn, H. T.↗

NASA NTRS1986

Failure criterion of glass fabric reinforced plastic laminates

Failure criteria are derived for several modes of failure (in unaxial tensile or compressive loading, or biaxial combined tensile-compressive loading) in the case of closely woven plain fabric, coarsely-woven plain fabric, or roving glass cloth reinforcements. The shear strength in the interaction formula is replaced by an equation dealing with tensile or compressive strength in the direction making a 45 degree angle with one of the anisotropic axes, for the uniaxial failure criteria. The interaction formula is useful as the failure criterion in combined tension-compression biaxial failure for the case of closely woven plain fabric laminates, but poor agreement is obtained in the case of coarsely woven fabric laminates.

Haga, O.↗

NASA NTRS1986

Compression failure mechanisms in unidirectional composites

Hahn, H. T.↗

NASA NTRS1986

Aircraft control surface failure detection and isolation using the OSGLR test

The performance of the orthogonal series generalized likelihood ratio (OSGLR) test in detecting and isolating commercial aircraft control surface and actuator failures is evaluated. A modification to incorporate age-weighting which significantly reduces the sensitivity of the algorithm to modeling errors is presented. The steady-state implementation of the algorithm based on a single linear model valid for a cruise flight condition is tested using a nonlinear aircraft simulation. A number of off-nominal no-failure flight conditions including maneuvers, nonzero flap deflections, different turbulence levels and steady winds were tested. Based on the no-failure decision functions produced by off-nominal flight conditions, the failure detection and isolation performance at the nominal flight condition was determined. The extension of the algorithm to a wider flight envelope by scheduling on dynamic pressure and flap deflection is examined. Based on this testing, the OSGLR algorithm should be capable of detecting control surface failures that would affect the safe operation of a commercial aircraft. Isolation may be difficult if there are several surfaces which produce similar effects on the aircraft. Extending the algorithm over the entire operating envelope of a commercial aircraft appears feasible.

Bonnice, W. F.↗

NASA NTRS1987

Fatigue failure of regenerator screens in a high frequency Stirling engine

Failure of Stirling Space Power Demonstrator Engine (SPDE) regenerator screens was investigated. After several hours of operation the SPDE was shut down for inspection and on removing the regenerator screens, debris of unknown origin was discovered along with considerable cracking of the screens in localized areas. Metallurgical analysis of the debris determined it to be cracked-off-deformed pieces of the 41 micron thickness Type 304 stainless steel wire screen. Scanning electron microscopy of the cracked screens revealed failures occurring at wire crossovers and fatigue striations on the fracture surface of the wires. Thus, the screen failure can be characterized as a fatigue failure of the wires. The crossovers were determined to contain a 30 percent reduction in wire thickness and a highly worked microstructure occurring from the manufacturing process of the wire screens. Later it was found that reduction in wire thickness occurred because the screen fabricator had subjected it to a light cold-roll process after weaving. Installation of this screen left a clearance in the regenerator allowing the screens to move. The combined effects of the reduction in wire thickness, stress concentration (caused by screen movement), and highly worked microstructure at the wire crossovers led to the fatigue failure of the screens.

Hull, David R.↗

NASA NTRS1985

A compressive failure model for anisotropic plates with a cutout under compressive and shear loads

Failure models for the prediction of compressive strength of plates with a hole are investigated. One of the models is based on the strength failure of the fibers that leads to fiber kinking failure. A different version is developed for cases where shear failure of the fibers is expected to be a dominate failure mode. Both models are capable of including the effects of combined shearing and compressive stresses around a hole in a plate and, therefore, are expected to be applicable to plates under combined shearing and compressive loadings, as well as anisotropic plates.

Guerdal, Zafer↗

NASA NTRS1988

Ply-level failure analysis of a graphite/epoxy laminate under bearing-bypass loading

A combined experimental and analytical study was conducted to investigate and predict the failure modes of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Tests were conducted in a test machine that allowed the bearing-bypass load ratio to be controlled while a single-fastener coupon was loaded to failure in either tension or compression. Onset and ultimate failure modes and strengths were determined for each test case. The damage-onset modes were studied in detail by sectioning and micrographing the damaged specimens. A two-dimensional, finite-element analysis was conducted to determine lamina strains around the bolt hole. Damage onset consisted of matrix cracks, delamination, and fiber failures. Stiffness loss appeared to be caused by fiber failures rather than by matrix cracking and delamination. An unusual offset-compression mode was observed for compressive bearing-bypass laoding in which the specimen failed across its width along a line offset from the hole. The computed lamina strains in the fiber direction were used in a combined analytical and experimental approach to predict bearing-bypass diagrams for damage onset from a few simple tests.

Naik, R. A.↗

NASA NTRS1988

Fatigue failure of regenerator screens in a high frequency Stirling engine

Failure of Stirling Space Power Demonstrator Engine (SPDE) regenerator screens was investigated. After several hours of operation the SPDE was shut down for inspection and on removing the regenator screens, debris of unknown origin was discovered along with considerable cracking of the screens in localized areas. Metallurgical analysis of the debris determined it to be cracked-off-deformed pieces of the 41 micron thickness Type 304 stainless steel wire screen. Scanning electron microscopy of the cracked screens revealed failures occurring at wire crossovers and fatigue striations on the fracture surface of the wires. Thus, the screen failure can be characterized as a fatigue failure of the wires. The crossovers were determined to contain 30 percent reduction in wire thickness and a highly worked microstructure occurring from the manufacturing process of the wire screens. Later it was found that reduction in wire thickness occurred because the screen fabricator had subjected it to a light cold-roll process after weaving. Installation of this screen left a clearance in the regenerator allowing the screens to move. The combined effects of the reduction in wire thickness, stress concentration (caused by screen movement), and highly worked microstructure at the wire crossovers led to the fatigue failure of the screens.

Hull, David R.↗