Search NASA⌕ Search

SEARCH · Search NASA

Results for “FOAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Trace levels of PtRu on NiMo foam electrodes towards hydrogen evolution reaction

Electrochemical water splitting plays a critical role in high purity hydrogen production. To lower capital cost and energy consumption, efficient catalysts are required to boost the hydrogen evolution reaction (HER), especially in alkaline media. Although PtRu alloy materials are still considered the state-of-the-art catalyst for the HER under alkaline media, large-scale application is hindered by its scarcity and high cost. NiMo alloy catalysts can be potential Pt-free alternatives to drive the sluggish kinetics of the HER under alkaline media, but their HER activity is still not ideal due to the limitation of Volmer step. Herein, we investigated the impact of trace levels of PtRu catalysts on NiMo electrodes towards the HER by incorporating advantages of both PtRu and NiMo catalysts to minimize cost and maintain a promising HER activity. Trace levels of PtRu catalysts from 0.0173 to 0.2648 mg cm −2 were loaded on commercial NiMo foam electrodes by a facile electrodeposition technique utilizing ppm concentration levels of PtRu in electrolyte. The results show that 0.0173 mg cm −2 PtRu loading on NiMo electrode can significantly enhance HER activity compared to the pristine NiMo foam electrode (Tafel slopes drop from ∼170 to ∼60 mV dec −1 ) due to the remarkable decline of energy barriers towards water dissociation and hydrogen adsorption. Meanwhile, the rate determining step (RDS) switches from the Volmer step to the Heyrovsky step when the PtRu loading increases to 0.0675 mg cm −2 . Promising catalytic stability is observed at 100 mA cm −2 over the course of 50 h with a PtRu loading of 0.1198 mg cm −2 . In conclusion, this work demonstrates a potential strategy to decrease the cost and simultaneously maintain superior HER performance by integrating trace levels of PtRu catalyst with NiMo foam electrodes.

Electrochemical water splitting↗
DOE OSTI2025

Physics of laser direct-drive liquid deuterium–tritium wetted foam capsules for inertial confinement fusion

Laser direct-drive liquid deuterium–tritium (DT) wetted foam capsules hold substantial promise for future advancements in inertial confinement fusion (ICF). For this new class of ICF capsules, additive manufacturing (AM) techniques are used to create low aspect ratio spherical shells of a low-density, foam-like CH lattice, which is wetted with cryogenic liquid DT. In the present paper, we discuss key physics issues intrinsic to ignition and burn propagation in laser direct drive wetted foam capsules. These include requirements on laser energy and power, implosion velocity, fuel adiabat, and initial density and dimensions of the CH lattice shell.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Characterization of Carbon Foam Products Made from Coal at Atmospheric Pressure

Carbon foam products are currently manufactured on a commercial scale utilizing a high-pressure autoclave in batch mode. In an effort to increase manufacturing speed and reduce cost, carbon foam products (both panels and aggregates) were produced at atmospheric pressure in a continuous belt kiln. Here, the microstructure, properties, and performance of these materials were characterized and assessed in various applications. Lightweight aggregate was explored for use as a proppant, as well as it use in concrete and asphalt. The thermal conductivity, water permeability, and fire resistance of panels were evaluated, and its performance with respect to screw pullout was compared against conventional building materials. Some interesting performance aspects and potential for future work was revealed. This work was supported by a cooperative agreement with the Department of Energy – National Energy Technology Laboratory (DE-FOA-0002185, Area of Interest 4: Coal-Derived Carbon Foam Produced via a Continuous Process, award number DE-FE-0031992).

01 COAL, LIGNITE, AND PEAT↗
NASA NTRSDate not supplied

Updated Analysis of the Trash Compaction and Processing System: Water Collected from Trash, Evaluation of the Source Contaminant Control System, and Zotek® F30 Foam Processing

The Trash Compaction and Processing System (TCPS) aims to reduce volume, biologically safen, physically stabilize, manage effluents, and recover resources from astronaut trash in the International Space Station (ISS). At NASA Ames Research Center (ARC), there are two test systems: the Heat Melt Compactor (HMC), which compacts the trash into a tile with temperature and pressure, and the Source Contaminant Control System (SCCS), which is the gas management subsystem aimed to reduce contaminants by converting them into carbon dioxide (CO 2 ) and water (H 2 O) vapor. Both the HMC and SCCS serve as test systems that support TCPS development by conducting risk reduction activities associated with an ISS technology demonstration. In this paper, the risk reduction activities discussed are the testing of different trash models for operational scenarios in the HMC, investigating the water extracted from those trash models, and managing the gaseous effluents from the trash via contaminant conversion through the SCCS. The HMC has undergone several tests of different trash models and cases in which a containment bag is used or not. For the first topic, this paper will analyze the water collected and recovered from these tests and analyze the effect of specific trash containment bags. For the second topic, this paper will individually evaluate the carbon bed and catalytic oxidizer (CatOx) to understand what components the carbon bed removes and what contaminants are converted in the CatOx. For the third and final topic, this paper will discuss Zotek® F30 foam processing in the HMC unit and testing verification in correlation to defined TCPS requirements. A foam model was added to reduce the volume of foam that take up space in the ISS. Overall, this paper is a compilation and an updated analysis of tests conducted in the lab-scale TCPS at ARC within the past year.

TCPS↗
DOE OSTI2024

Embedded Fluidic Sensing and Control with Soft Open‐Cell Foams

Abstract The synthesis of soft matter intelligence with circuit‐driven logic has enabled a new class of robots that perform complex tasks or conform to specialized form factors in unique ways that cannot be realized through conventional designs. Translating this hybrid approach to fluidic systems, the present work addresses the need for sheet‐based circuit materials by leveraging the innate porosity of foam—a soft material—to develop pneumatic components that support digital logic, mixed‐signal control, and analog force sensing in wearables and soft robots. Analytical tools and experimental techniques developed in this work serve to elucidate compressible gas flow through porous sheets, and to inform the design of centimeter‐sized foam resistors with fluidic resistances on the order of 10 9 Pa s m −3 . When embedded inside soft robots and wearables, these resistors facilitate diverse functionalities spanning both sensing and control domains, including digital logic using textile logic gates, digital‐to‐analog signal conversion using ladder networks, and analog sensing of forces up to 40 N via compression‐induced changes in resistance. By combining features of both circuit‐based and materials‐based approaches, foam‐enabled fluidic circuits serve as a useful paradigm for future hybrid robotic architectures that fully embody the sensing and computing capabilities of soft fluidic materials.

Rajappan, Anoop↗
DOE OSTI2025

Shape‐Stabilization of Phase Change Materials with Carbon‐Conscious Poly(hydroxy)Urethane Foams

Thermal energy regulation is a significant challenge, contributing to over 30% of annual greenhouse gas emission (GHG) emissions. Phase change materials (PCMs) offer a promising solution by storing thermal energy, which can enable the reuse of waste heat for heating and cooling; however, developing materials for shape-stabilized PCMs remains crucial. This work investigates a self-foaming poly(hydroxy)urethane (PHU), derived from a non-isocyanate polyurethane (NIPU), as a porous support for shape-stabilizing paraffinic and salt hydrate PCMs. PHU-encapsulated paraffinic PCMs exhibited excellent thermal stability over repeated cycles. Thermal stability with salt hydrate PCMs, specifically calcium chloride hexahydrate (CaCl 2 •6H 2 O), is achieved by the incorporation of 5 wt.% barium carbonate (BaCO 3 ) into the PHU foam. This enabled stable cycling for over 48 cycles with desirable thermal properties, i.e., a melting point ≈30 °C, high enthalpy (ca. 138 J g −1 per cycle), and a consistent freezing point ≈20 °C, making it suitable for applications in buildings and electric vehicle battery insulation. Also, incorporating graphite (1.5–10 wt.%) into the foam enhanced the thermal conductivity of shape-stabilized CaCl 2 •6H 2 O during heating and cooling cycles. Overall, the approach detailed here offers a carbon-conscious and chemically tunable material for thermal energy storage.

25 ENERGY STORAGE↗
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
DOE OSTI2025

Life-cycle analysis of microalgae-based polyurethane foams

Polyurethane plastics are essential in many consumer and commercial products such as insulation, furniture, automotive interiors, and clothing. Pathways for producing polyurethane from microalgae offer an opportunity to reduce greenhouse gas emissions and other environmental impacts and can incorporate processes that avoid the use of toxic isocyanates typically used in conventional polyurethane production processes. In this study, the greenhouse gas emissions, fossil energy, and water consumption of biobased polyurethane and biobased non-isocyanate polyurethane were evaluated via life-cycle analysis using the R&D Greenhouse Gases, Regulated Emissions, and Energy Use in Technologies model. Microalgae-based polyurethane foam was found to achieve greenhouse gas emission reductions of up to 79% compared with conventional polyurethane foam production. The greenhouse gas reductions for the non-isocyanate microalgae polyurethane pathway are slightly lower at 58% compared with conventional polyurethane foam. However, it offers additional benefits by reducing toxicity potential compared to the isocyanate polyurethane pathway. The analysis also included a biorefinery-level analysis to evaluate the impact of incorporating polyurethane production into fuel-processing microalgae biorefineries. The sensitivity analyses conducted in this study reveal that improved algae cultivation strategies can lead to decreases of up to 127% and 80% in GHG emissions from the baseline process of Bio-PU and Bio-NIPU, respectively. Likewise, implementation of renewable electricity can result in up to 128% and 74% lower GHG emissions compared to the baseline production of Bio-PU and Bio-NIPU, respectively. Finally, the analysis evaluated different coproduct handling methods including displacement and allocation (based on mass, energy, and market-value). The results suggest that it is important to consider both the displacement and allocation methods as these led to significant differences in the environmental impacts.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Wetted-foam target stability for laser-direct-drive inertial confinement fusion

Using highly resolved three-dimensional radiation-hydrodynamic simulations, the effects of wetted-foam (WF) ablators in direct-drive inertial confinement fusion cryogenic implosions on the OMEGA laser were investigated. The performance of these implosions was compared with that of implosions using targets with solid-plastic ablators. Simulations considering WF ablators as a homogeneous material show no mitigation of the effects of laser imprint, where the absence of this mitigation can be attributed to the use of picket pulses. Heterogeneous random-structure WF ablators introduce large short-wavelength perturbations, which are seeded by WF inhomogeneities. These perturbations exceed the perturbations seeded by the imprint and cause an additional reduction in implosion performance when the average pore size in the WF exceeds ~0.2 μm. Foam-seeded perturbations are expected to be less damaging in more stable high-adiabat (⁠ ≳ 5⁠) implosions. Here, the perturbations introduced by the WF ablators can be substantially reduced by using a foam matrix with a layered structure instead of a random one. Further study of the effects of WFs in ignition designs of the MJ laser energy scale is required in the perspective of future inertial fusion energy mass production.

Igumenshchev, I. V. [University of Rochester, NY (↗
DOE OSTI2025

Foam and Unreacted Material Reduction in Magnesium Oxysulfate for SRPPF Waste Solidification

A magnesium oxysulfate (MOS) grout formulation has been proposed to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). This formulation uses a combination of light-burnt MgO, anhydrous MgSO 4 , and dead-burnt MgO resulting in a grout with good mixability and acceptable density. The setting time for the grout is within the operational limits of the SRPPF facility and the leachate pH is ~9.4, which is within the assumed pH range of the brine from the Waste Isolation Pilot Plant (WIPP). When first tested at the 1-gallon small-scale and 55-gallon full-scale, there was a significant foam layer that raised concerns of a nonhomogeneous final form. A nonhomogeneous mixture could have variable density throughout the waste form and therefore allow for unequal shielding. To reduce the potential for unequal shielding in the final form, a series of foam reduction tests were carried out and a final formulation of 28 wt% light burnt MgO, 10 wt% MgSO 4 , and 62 wt% dead burnt MgO was used to remove the foam in under two hours while still maintaining a mix that has an acceptable density, mix time, peak temperature, and set time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

FY25 Cellular Silicone Foam Friction Testing Summary Report

This effort was a collaboration between LANL groups MPA-CINT, E-13, and V-14 to characterize various properties of foam materials for programmatic work. Specifically, MPA-CINT staff members’ contribution to this effort was to perform friction testing of cellular silicone foams of two different porosities with respect to two engineering materials with predefined surface roughnesses. The selected foams (henceforth serving as the sled material interface exposed to motion) had porosities of 67% and 70% with respect to fabricated values. The other materials used in the friction testing measurement couple (static track material) were 304 Stainless Steel (304 SS) and Very High-Temperature Glass-Mica Ceramic, known as Macor®.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Develop Renewable/Sustainable Material to Displace Petroleum-Derived Polymer Foams (CRADA Final Report)

NLR and EDEN will partner together to develop renewable, biodegradable alternatives to polyfoam (polyurethane) polymer foams. The initial focus will be on developing cellulose-based foam with tunable mechanical properties. NLR will produce and test the cellulose-based foam materials and characterize its microstructure and mechanical properties. Relationships between mechanical performance formulation and fabrication methods will be developed.

09 BIOMASS FUELS↗
NASA NTRS1971

Materials for foam type insulation

An internal foam fabrication is one of the concepts being considered for cryogenic insulation on the hydrogen tanks of the shuttle vehicle. The three-dimensional polyurethane used on the S-4 B tanks failed to meet the higher temperature requirements of the shuttle vehicle, however, and other foams under consideration include polyisocyanurates, polyphenylene oxides, polyimides, and polybenzimidazoles. Improved adhesive systems for attaching the foams to the interior tank wall are under study.

Hill, W. E.↗
NASA NTRS1973

Characteristics of a gelled liquid hyprogen polyphenylene oxide (PPO) foam open-cell insulation system, phase 1

A large scale gel production and storage facility and a small scale facility, the latter used for detailed visual examination of the gel/PPO foam interface, were developed. A subcontract was given to investigate techniques for the production of gelled liquid hydrogen, develop a process design for scale-up to a 1.89 cu m (500 gallon) gel production and storage facility, determine gel transfer characteristics, determine the solubility rate of gaseous helium in the gel, and investigate the gross gel/PPO foam interfacial phenomena. An inside-tank process for scaled-up production of gelled liquid hydrogen was selected. No detectable gel structure degradation occurred during repeated shearing. The viscosity of gelled liquid hydrogen at shear rates of 300/sec and higher is 2 to 5-fold greater than that of neat liquid hydrogen. No clogging problems were encountered during the transfer of gelled liquid hydrogen through warmed transfer lines. The solubility rate of helium in liquid hydrogen was significantly reduced by the presence of gel structure. The boil-off rates from gelled liquid hydrogen were reduced from 25 to 50 percent compared to those observed for the neat liquid hydrogen under compatible conditions. The polyphenylene oxide (PPO) foam insulation was found to be compatible with liquid ethane.

Source record↗
NASA NTRS1973

Carbon microsphere-filled Pyrrone foams.

Syntactic foam formulations were prepared from mixtures of Pyrrone prepolymers and hollow carbon microspheres. Very low curing shrinkages were obtained for high volume loadings of microspheres. The resulting syntactic foams were found to be remarkably stable over a wide range in temperature. A technique was developed for the emplacement of these foam formulations in polyimide-fiberglass, titanium alloy and stainless steel honeycomb without sacrificing low curing shrinkage or thermal stability.

Kimmel, B. G.↗
NASA NTRS1974

Metallized polymeric foam material

Open-celled polyurethane foams can be coated uniformly with thin film of metal by vapor deposition of aluminum or by sensitization of foam followed by electroless deposition of nickel or copper. Foam can be further processed to increase thickness of metal overcoat to impart rigidity or to provide inert surface with only modest increase in weight.

Birnbaum, B. A.↗
NASA NTRS1973

Polyimide foam for the thermal insulation and fire protection

The preparation of chemically resistant and flame retardant foams from polyfunctional aromatic carboxylic acid derivatives and organic polyisocyanates is outlined. It was found that polyimide foams of reproducible density above 1 lb./ft. and below 6 lbs./cu ft. can be obtained by employing in the reaction of least 2% by weight of siloxane-glycol copolymer as a surfactant which acts as a specific density control agent. Polyimide foams into which reinforcing fibers such as silicon dioxide and carbon fibers may be incorporated were also produced.

Rosser, R. W.↗