Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flux adjustment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Measurement of Ultraviolet Radiative Heating Augmentation in HIEST Reflected Shock Tunnel

Radiance measurements in air at enthalpies from 8-20 MJkg have been made over a 250mm diameter flat-faced test article in Japan Aerospace Exploration Agency's HIgh-Enthalpy Shock Tunnel (HIEST). Measurements were made in the ultraviolet region (200-400 nm wavelength) in an attempt to resolve the long-standing discrepancy between theoryand measurements of heat flux over a blunt body; this discrepancy is often attributed toradiation. The spectra obtained indicate the presence of atomic iron vapor in the flowfield.At the highest enthalpies, the radiance is at the blackbody limit. An attempt to model theradiance is made by taking a nominal CFD flowfield without any contamination productsand processing it through a line-by-line radiation simulation tool. Iron vapor is introducedinto the shocked gas ahead of the model and radiation computations are repeated; the molefraction of iron vapor is adjusted to match the data. For the higher enthalpy conditions, theradiance was strongly absorbed and it was necessary to adjust the temperature and NOdensity in the freestream to match the signal below 300 nm. Once the observed spectrawere satisfactorily matched, the radiance to the stagnation point was then computed. It isshown that the impurity radiation is sufficiently large to explain the discrepancy.

Shock Tunnel↗
NASA NTRS2001

Implementing a Nitrogen-Based Model for Autotrophic Respiration Using Satellite and Field Observations

The rate of carbon accumulation by terrestrial plant communities in a process-level, mechanistic modeling is the difference of the rate of gross photosynthesis by a canopy (A(sub g)) and autotrophic respiration (R) of the stand. Observations for different biomes often show that R to be a large and variable fraction of A(sub g), ca. 35% to 75%, although other studies suggest the ratio of R and A(sub g) to be less variable. Here, R has been calculated according to the two compartment model as being the sum of maintenance and growth components. The maintenance respiration of foliage and living fine roots for different biomes has been determined objectively from observed nitrogen content of these organs. The sapwood maintenance respiration is based on pipe theory, and checked against an independently derived equation considering sapwood biomass and its maintenance coefficient. The growth respiration has been calculated from the difference of A(sub g) and maintenance respiration. The A(sub g) is obtained as the product of biome-specific radiation use efficiency for gross photosynthesis under unstressed conditions and intercepted photosynthetically active radiation, and adjusted for stress. Calculations have been done using satellite and ground observations for 36 consecutive months (1987-1989) over large contiguous areas (ca. 10(exp 5) sq km) of boreal forests, crop land, temperate deciduous forest, temperate grassland, tropical deciduous forest, tropical evergreen forest, tropical savanna, and tundra. The ratio of annual respiration and gross photosynthesis, (R/A(sub g)), is found to be 0.5-0.6 for temperate and cold adopted biome areas, but somewhat higher for tropical biome areas (0.6-0.7). Interannual variation of the fluxes is found to be generally less than 15%. Calculated fluxes are compared with observations and several previous estimates. Results of sensitivity analysis are presented for uncertainties in parameterization and input data. It is found that uncertainty in determining maintenance respiration for tropical biomes is such that R/A(sub g) for these biomes could be similar to that for temperate biomes.

Choudhury, Bhaskar J.↗
NASA NTRS2004

Impacts of Air-Sea Interaction on Tropical Cyclone Track and Intensity

The influence of hurricane-ocean coupling on intensity and track of tropical cyclones (TCs) is investigated through idealized numerical experiments using a coupled hurricane-ocean model. The focus is placed on how air-sea interaction affects TC tracks and intensity. It is found that the symmetric sea surface temperature (SST) cooling is primarily responsible for the TC weakening in the coupled experiments because the induced asymmetric circulation associated with the asymmetric SST anomalies is weak and shallow. The track difference between the coupled and fixed SST experiments is generally small because of the competing processes. One is associated with the modified TC asymmetries. The asymmetric SST anomalies - weaken the surface fluxes in the rear and enhance the fluxes in the front. As a result, the enhanced diabatic heating is located on the southern side for a westward-moving TC, tending to shift the TC southward. The symmetric SST anomalies weakens the TC intensity and thus the dymmetrization process, leading to more prominent TC asymmetries. The other is associated with the weakening of the beta drift resulting from the weakening of the TC outer strength. In the coupled experiment, the weakening of the beta drift leads to a more northward shift. By adjusting the vortex outer strength of the initial vortices, the beta drift can vary while the effect of air-sea interaction changes little. Two types of track differences simulated in the previous numerical studies are obtained.

Wu, Liguang↗
NASA NTRS1983

Expansion of the solar wind from a two-hole corona

A one-fluid model is employed to study the global expansion of the solar wind from a two-hole corona, under the assumptions that the holes are confined to polar caps within 30 deg of heliographic colatitude, the flow is steady and axisymmetric, and the geometry of streamlines is prescribed. The boundary conditions are adjusted in such a way that the calculated solar-wind properties at 1 AU are in reasonable agreement with observational results. A series of numerical solutions are obtained, the series produces a maximum terminal speed of 829 km/s at the pole. The calculated solar-wind speeds are strongly latitude-dependent and are positively correlated with local divergence factor of a stream tube. The solutions imply that most plasma properties are highly inhomogeneous at the polar caps. The flow velocity, the temperature, the proton-number flux and the conduction-heat flux all increase towards the hole center.

Whang, Y. C.↗
NASA NTRS2000

BOREAS TE-6 Multiband Vegetation Imager Data

The BOREAS TE-6 team collected data in support of its efforts to examine the influence of vegetation and climate on the major carbon fluxes in boreal tree species. A newly developed ground-based canopy imaging system called an MVI was tested and used by the BOREAS TE-06 team to collect measurements of the canopy crap fraction (sky fraction), canopy gap-size distribution (size and frequency of gaps between foliage in canopy), branch architecture, and leaf angle distribution (fraction of leaf area in specific leaf inclination classes assuming azimuthal symmetry). Measurements of the canopy gap-size distribution are used to derive canopy clumping indices that can be used to adjust indirect LAI measurements made in nonrandom forests. These clumping factors will also help to describe the radiation penetration in clumped canopies more accurately by allowing for simple adjustments to Beer's law. Measurements of the above quantities were obtained at BOREAS NSA-OJP site in IFC-2 in 1994, at the SSA-OA in July 1995, and at the SSA-OBS and SSA-OA sites in IFC-2 in 1996. Modeling studies were also performed to further validate MVI measurements and to gain a more complete understanding of boreal forest canopy architecture. By using MVI measurements and Monte Carlo simulations, clumping indices as a function of zenith angle were derived for the three main boreal species studied during BOREAS. The analyzed data are stored in tabular ASCII files. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distrobuted Activity Archive Center (DAAC).

Hall, Forrest G.↗
NASA NTRS1980

Initial comparison of SSPM ground test results and flight data to NASCAP simulations

The satellite surface potential monitor (SSPM) has been developed for the P78-2 SCATHA (Spacecraft Charging At The High Altitudes) satellite to determine the response of selected spacecraft materials to charged-particle environmental fluxes. Since the monitor infers total surface voltages from a single point on the interior side of insulators, a ground simulation program was undertaken to develop analytical techniques to model the monitors and to obtain an experimental calibration of the relationship between the flight measurement techniques and actual measurements. The experimental testing was conducted using monoenergetic electron beams irradiating samples in the dark. An analytical computer model was developed in the NASCAP (NASA Charging Analyzer Program) code. The analytical model material properties for Kapton that controlled backscatter and secondary yield were adjusted to obtain a single set of values that produced reasonable fits for both voltages and currents. The analytical techniques developed in the ground technology investigation have been applied to space flight conditions. Predictions were compared with limited flight data. The agreement is very good indicating that the technique, and NASCAP, can be used to predict spacecraft material charging behavior. Details of the testing, the analytical modelling technique and flight data comparisons are presented.

Stevens, N. J.↗
NASA NTRS1992

Meso-beta scale numerical simulation studies of terrain-induced jet streak mass/momentum perturbations

Work performed during the report period is summarized. The first numerical experiment which was performed on the North Carolina Supercomputer Center's CRAY-YMP machine during the second half of FY92 involved a 36 hour simulation of the CCOPE case study. This first coarse-mesh simulation employed the GMASS model with a 178 x 108 x 32 matrix of grid points spaced approximately 24 km apart. The initial data was comprised of the global 2.5 x 2.5 degree analyses as well as all available North American rawinsonde data valid at 0000 UTC 11 July 1981. Highly-smoothed LFM-derived terrain data were utilized so as to determine the mesoscale response of the three-dimensional atmosphere to weak terrain forcing prior to including the observed highly complex terrain of the northern Rocky Mountain region. It was felt that the model should be run with a spectrum of terrain geometries, ranging from observed complex terrain to no terrain at all, to determine how crucial the terrain was in forcing the mesoscale phenomena. Both convection and stratiform (stable) precipitation were not allowed in this simulation so that their relative importance could be determined by inclusion in forth-coming simulations. A full suite of planetary boundary layer forcing was allowed in the simulation, including surface sensible and latent heat fluxes employing the Blakadar PBL formulation. The details of this simulation, which in many ways could be considered the control simulation, including the important synoptic-scale, meso-alpha scale, and meso-beta scale circulations is described. These results are compared to the observations diagnosed by Koch and his colleagues as well as hypotheses set forth in the project proposal for terrain-influences upon the jet stream and their role in the generation of mesoscale wave phenomenon. The fundamental goal of the analyses being the discrimination among background geostrophic adjustment, terrain influences, and shearing instability in the initiation and maintainance of mesoscale internal wave phenomena. Based upon these findings, FY93 plans are discussed. A review of linear theory and theoretical modeling of a geostrophic zonal wind anomaly is included.

Lin, Yuh-Lang↗
NASA NTRS1998

Measurements of the Downward Longwave Radiation Spectrum over the Antarctic Plateau and Comparisons with a Line-by-Line Radiative Transfer Model for Clear Skies

A 1-year field program was conducted at South Pole Station in 1992 to measure the downward infrared radiance spectrum at a resolution of 1/ cm over the spectral range 550-1667 cm-'. The atmosphere over the Antarctic Plateau is the coldest and driest on Earth, where in winter, surface temperatures average about -60 C, the total column water vapor is as low as 300 pm of precipitable water, and the clear-sky downward longwave flux is usually less than 80 W/sq m. Three clear-sky test cases are selected, one each for summer, winter, and spring, for which high- quality radiance data are available.as well as ancillary data to construct model atmospheres from radiosondes, ozonesondes, and other measurements. The model atmospheres are used in conjunction with the line-by-line radiative transfer model (LBLRTM) to compare model calculations with the spectral radiance measurements. The high-resolution calculations of LBLRTM (approx. = 0.001/ cm) are matched to the lower-resolution measurements (1/ cm) by adjusting their spectral resolution and by applying a correction for the finite field of view of the interferometer. In summer the uncertainties in temperature and water vapor profiles dominate the radiance error in the LBLRTM calculations. In winter the uncertainty in viewing zenith angle becomes important as well as the choice of atmospheric levels in the strong near-surface temperature inversion. The spectral radiance calculated for each of the three test cases generally agrees with that measured, to within twice the total estimated radiance error, thus validating LBLRTM to this level of accuracy for Antarctic conditions. However, the discrepancy exceeds twice the estimated error in the gaps between spectral lines in the region 1250-1500/ cm, where emission is dominated by the foreign-broadened water vapor continuum.

Walden, Von P.↗
NASA NTRS1994

The boundary layer of Mars: Fluxes, stability, turbulent spectra, and growth of the mixed layer

Spectra of wind from high-frequency measurements in the Martian atmospheric surface layer, along with the diurnal variation of the height of the mixed surface layer, are calculated for the first time for Mars. Heat and momentum fluxes, stability, and z(sub 0) are estimated for early spring from a surface temperature model and from Viking Lander 2 temperatures and winds at 44 deg N, using Monin-Obukhov similarity theory. Flow distortion by the lander is also taken into account. Model spectra for two measuring heights and three surface roughnesses are calculated using the depth of the mixed layer and the surface-layer parameters. These experiments indicate that z(sub 0) probably lies between 1.0 and 3.0 cm, and most likely is closer to 1.0 cm. The spectra are adjusted to simulate aliasing and high-frequency rolloff, the latter caused by both the sensor response and the large Kolmogorov length on Mars. Since the spectral models depend on the surface parameters, including the estimated surface temperature, their agreement with the calculated spectra indicates that the surface-layer estimates are self-consistent. This agreement is especially noteworthy in that the inertial subrange is virtually absent in the Martian atmosphere at this height, due to the large Kolmogorov length scale. These analyses extend the range of applicability of terrestrial results and demonstrate that it is possible to estimate the effects of severe aliasing of wind measurements, to produce models that agree well with the measured spectra. The results show that similarity theory developed for Earth applies to Mars, and that the spectral models are universal.

Tillman, James E.↗
NASA NTRS1976

Application of remote sensing in estimating evapotranspiration in the Platte river basin

A 'resistance model' and a mass transport model for estimating evapotranspiration (ET) were tested on large fields of naturally subirrigated alfalfa. Both models make use of crop canopy temperature data. Temperature data were obtained with an IR thermometer and with leaf thermocouples. A Bowen ratio-energy balance (BREB) model, adjusted to account for underestimation of ET during periods of strong sensible heat advection, was used as the standard against which the resistance and mass transport models were compared. Daily estimates by the resistance model were within 10% of estimates made by the BREB model. Daily estimates by the mass transport model did not agree quite as well. Performance was good on clear and cloudy days and also during periods of non-advection and strong advection of sensible heat. The performance of the mass transport and resistance models was less satisfactory for estimation of fluxes of latent heat for short term periods. Both models tended to overestimate at low LE fluxes.

Blad, B. L.↗
NASA NTRS1999

Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

In boiling high heat fluxes are possible driven by relatively small temperature differences, which make its use increasingly attractive in aerospace applications. The objective of the research is to develop ways to overcome specific problems associated with boiling in the low gravity environment by substituting the buoyancy force with the electric force to enhance bubble removal from the heated surface. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50, as compared to values obtained for the same system without electric fields. The goal of our research is to experimentally explore the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions, by visualizing the temperature distributions in the vicinity of the heated surface and around the bubble during boiling using real-time holographic interferometry (HI) combined with high-speed cinematography. In the first phase of the project the influence of the electric field on a single bubble is investigated. Pool boiling is simulated by injecting a single bubble through a nozzle into the subcooled liquid or into the thermal boundary layer developed along the flat heater surface. Since the exact location of bubble formation is known, the optical equipment can be aligned and focused accurately, which is an essential requirement for precision measurements of bubble shape, size and deformation, as well as the visualization of temperature fields by HI. The size of the bubble and the frequency of bubble departure can be controlled by suitable selection of nozzle diameter and mass flow rate of vapor. In this approach effects due to the presence of the electric field can be separated from effects caused by the temperature gradients in the thermal boundary layer. The influence of the thermal boundary layer can be investigated after activating the heater at a later stage of the research. For the visualization experiments a test cell was developed. All four vertical walls of the test cell are transparent, and they allow transillumination with laser light for visualization experiments by HI. The bottom electrode is a copper cylinder, which is electrically grounded. The copper block is heated with a resistive heater and it is equipped with 6 thermocouples that provide reference temperatures for the measurements with HI. The top electrode is a mesh electrode. Bubbles are injected with a syringe into the test cell through the bottom electrode. The working fluids presently used in the interferometric visualization experiments, water and PF 5052, satisfy requirements regarding thermophysical, optical and electrical properties. A 30kV power supply equipped with a voltmeter allows to apply the electric field to the electrodes during the experiments. The magnitude of the applied voltage can be adjusted either manually or through the LabVIEW data acquisition and control system connected to a PC. Temperatures of the heated block are recorded using type-T thermocouples, whose output is read by a data acquisition system. Images of the bubbles are recorded with 35mm photographic and 16mm high-speed cameras, scanned and analyzed using various software packages. Visualized temperature fields HI allows the visualization of temperature fields in the vicinity of bubbles during boiling in the form of fringes. Typical visualized temperature distributions around the air bubbles injected into the thermal boundary layer in PF5052 are shown. The temperature of the heated surface is 35 C. The temperature difference for a pair of fringes is approximately 0.05 C. The heat flux applied to the bottom surface is moderate, and the fringe patterns are regular. In the image a bubble penetrating the thermal boundary layer is visible. Because of the axial symmetry of the problem, simplified reconstruction techniques can be applied to recover the temperature field. The thermal plume developing above the heated surface for more intensive heating is shown. The temperature distribution in the liquid is clearly 3D, and tomographic techniques have to be applied to recover the temperature distribution in such a physical situation. A sequence of interferometric images showing the temperature distribution around the rising bubble, recorded with a high-speed camera is shown. Again, the temperature distribution is 3D, and a more complex approach to the evaluation, the tomographic reconstruction has to be taken. Measurement of the temperature distribution from the fringe pattern temperature distributions that yield important information regarding heat transfer are determined. Two algorithms that allow the quantitative evaluation of interferometric fringe patterns and the reconstruction of temperature fields during boiling have been developed at the Heat Transfer Laboratory of the Johns Hopkins University. In the first algorithm the bubble is assumed to be axially symmetrical, which significantly reduces the computational effort for quantifying the temperature distribution around the bubble. For this purpose the thermal boundary layer around the bubble is divided into equidistant concentric shells, and the refractive index is assumed to be constant in each of the shells. Since large temperature gradients are expected in the vicinity of the bubble during boiling, the deflection of the light beam cannot be neglected in boiling experiments. Since the exit angle of the light beam is known, this allows to account for the deflections and phase shifts outside the boundary layer (in the bulk fluid and in the windows of the test cell). Three dimensional temperature distributions in the vicinity of the bubble are reconstructed using tomographic techniques. In tomography, the measurement volume is sliced into 2D planes. In the present study these planes are parallel to the heated surface. The objective is to determine the values of the field parameter of interest in form of the field function in these 2D planes. The field parameter is the change of the refractive index of the liquid in the measurement volume caused by temperature changes. By superimposing data for many 2D planes recorded at the same time instant, the 3D temperature distribution in the measurement volume is recovered.

Herman, Cila↗
NASA NTRS2014

The QBO in Two GISS Global Climate Models: 1. Generation of the QBO

The adjustment of parameterized gravity waves associated with model convection and finer vertical resolution has made possible the generation of the quasi-biennial oscillation (QBO) in two Goddard Institute for Space Studies (GISS) models, GISS Middle Atmosphere Global Climate Model III and a climate/middle atmosphere version of Model E2. Both extend from the surface to 0.002 hPa, with 2deg × 2.5deg resolution and 102 layers. Many realistic features of the QBO are simulated, including magnitude and variability of its period and amplitude. The period itself is affected by the magnitude of parameterized convective gravity wave momentum fluxes and interactive ozone (which also affects the QBO amplitude and variability), among other forcings. Although varying sea surface temperatures affect the parameterized momentum fluxes, neither aspect is responsible for the modeled variation in QBO period. Both the parameterized and resolved waves act to produce the respective easterly and westerly wind descent, although their effect is offset in altitude at each level. The modeled and observed QBO influences on tracers in the stratosphere, such as ozone, methane, and water vapor are also discussed. Due to the link between the gravity wave parameterization and the models' convection, and the dependence on the ozone field, the models may also be used to investigate how the QBO may vary with climate change.

middle atmosphere dynamics↗
NASA NTRS2002

Mass Conservation in a Chemical Transport Model and its Effect on CO2 and SF6 Simulations

Chemical transport models (CTMs) must conserve mass to be useful for applications involving assessment of the effect of various pollutants on the troposphere and stratosphere. Furthermore, calculations of the evolution of constituents such as SF6 are used to evaluate overall model transport, and interpretation of such simulations is clouded if mass conservation is not assured. For realistic simulations or predictions, it is crucial that constituents are not produced or lost by transport or other processes in the CTMs. Analysis of CO2 and SF6 experiments using a CTM shows that problems with mass conservation can seriously degrade the simulations. Failure to conserve mass results from inconsistency of the surface pressure tendency and the divergence of horizontal mass flux when the model is forced by assimilated meteorological data. We have developed an effective method to eliminate the inconsistency by modifying the divergent part of the wind field. The changes in the wind fields are quite small but the impact on mass conservation is large. Parameterizations of physical processes such as convection or turbulent transport can also affect mass conservation. The lack of conservation is small but accumulates when integrations are lengthy such as required for SF6. This lack of conservation is found using winds from either a GCM or from an assimilation system. A simple adjustment removes much of the inaccuracy in the convective parameterization. A CO2 simulation using assimilated winds from the most recent version of the Goddard Earth Observing System Data Assimilation System will be used to illustrate the impact of these transport improvements.

Zhu, Z.↗
NASA NTRS1991

Observations of Scorpius X-1 with IUE - Ultraviolet results from a multiwavelength campaign

IUE UV results are presented for the low-mass X-ray binary Sco X-1. Models that predict UV continuum emission from the X-ray-heated surface from the companion star and from an X-ray illuminated accretion disk are adjusted for parameters intrinsic to Sco X-1, and fitted to the data. X-ray heating is found to be the dominant source of UV emission; the mass-accretion rate increases monotonically along the 'Z-shaped' curve in an X-ray color-color diagram. UV emission lines from He, C, N, O, and Si were detected; they all increase in intensity from the HB to the FB state. A model in which emission lines are due to outer-disk photoionization by the X-ray source is noted to give good agreement with line fluxes observed in each state.

Vrtilek, S. D.↗
NASA NTRS1984

An Earth longwave radiation climate model

An Earth outgoing longwave radiation (OLWR) climate model was constructed for radiation budget study. Required information is provided by on empirical 100mb water vapor mixing ratio equation of the mixing ratio interpolation scheme. Cloud top temperature is adjusted so that the calculation would agree with NOAA scanning radiometer measurements. Both clear sky and cloudy sky cases are calculated and discussed for global average, zonal average and world-wide distributed cases. The results agree well with the satellite observations. The clear sky case shows that the OLWR field is highly modulated by water vapor, especially in the tropics. The strongest longitudinal variation occurs in the tropics. This variation can be mostly explained by the strong water vapor gradient. Although in the zonal average case the tropics have a minimum in OLWR, the minimum is essentially contributed by a few very low flux regions, such as the Amazon, Indonesian and the Congo.

Yang, S. K.↗
NASA NTRS2019

Validation of CERES Flight Model 5 In-Orbit Calibrations Using Lunar Observations

Scientific studies require radiation fluxes over the Earth to be accurate within 1% for shortwave fluxes and 0.5% for outgoing longwave fluxes. The validation of in-orbit instrument performance requires both stability in calibration source and also calibration corrections to compensate for instrument changes. The Moon offers an external source whose signal variance is predictable and non-degrading. CERES detectors register the signal output from the entire face of the Moon. Lunar observations performed by CERES Flight Models (FM) 1 through 4 have been successful in assisting validation of radiances to the required accuracy. CERES Flight Model 5 (FM-5) is on Suomi/NPP spacecraft, orbiting since October 2011. This paper uses lunar measurements to validate detector output of FM-5. These measurements are adjusted to remove orbital effects due to variations in distance between Moon and Sun, distance between the satellite and the Moon and lunar phase angle. These effects create a total variation in lunar irradiance of 20% in the total channel and 8% in the shortwave channel. The change in orientation of the Moon as seen by the detector is called libration and causes variations of about 1% of the irradiance. A consistent dataset spanning at least 2 years in length is required to remove variations due to libration. The major uncertainties remaining in the measurements are assumed to be due to changes of the spectral responses of the channels due to degradation of optical surfaces in orbit. The results demonstrate that lunar observations can be used to validate FM-5 measurements.

Clouds and Earth Radiant Energy System↗
NASA NTRS2019

Scaling Evaluation of Ice-Crystal Icing on a Modern Turbofan Engine in PSL Using the COMDES-MELT Code

This paper presents preliminary ice-crystal icing (ICI) altitude scaling evaluation results of a Honeywell Uncertified Research Engine (HURE) that was tested in the NASA Glenn Research Center Propulsion Systems Laboratory (PSL) during January of 2018. This engine geometry features a hidden core design to keep the core less exposed. The engine was fitted with internal video cameras to observe various ice buildup processes at multiple selected locations within the engine core flow path covering the fan stator, the splitter-lip/shroud/strut, and the high pressure compressor (HPC) variable inlet guide vane (IGV) regions. The potential ice accretion risk was pre-determined to occur by using NASA’s in-house 1D Engine Icing Risk assessment code, COMDES-MELT. The code was successful in predicting the risk of ice accretion in adiabatic regions like the fan-stator of the HURE at specific engine operating points. However at several operating points during the test, liquid water was observed running along the shroud toward the variable IGV of the HPC regions with an air temperature well below freezing, thus no particle melting could have occurred due to heating from the air alone. It was reasoned that other sources of heat were present in that region. To account for these heat sources the inlet total temperature was adjusted to give a wet bulb temperature of 24 F below the standard minimum wet bulb temperature of 492 R to allow ice to accrete in the splitter-lip/shroud/strut region, which was determined from a reference case where hard ice was observed in that region. With that adjustment the COMDES-MELT code was successful in providing operating points where there was a risk of ice accretion during the test campaign. In addition to calculating possible conditions at different selected lower altitudes, simulations were run to determine potential inlet conditions that could lead to ice-crystal accretion along the prescribed stations where the cameras were available. From there, scaled test conditions were determined by best matching the following three icing related parameters of the reference condition: (1) the local air total wet bulb temperature, (2) the local ice crystal cloud melt ratio and (3) the engine fan face ice/water to air mass flux ratio of the ice crystal cloud. Instantaneous images taken from the time-lapsed movies of ice buildup were used along with the relevant thermodynamic data of air, water vapor and local icing condition to help evaluate how closely the proposed altitude scaling method could be used in ground based test facility to duplicate selected reference ICI features observed at specific location inside this engine at different scale altitudes. Discussions on observed limitation for engine icing scaling application from this test campaign and needed improvement are provided. A scaling test procedure to help identify potential ICI risk conditions and possible ice accretion locations of a new turbofan engine is evaluated in PSL.

Engine Testing in PSL↗
NASA NTRS1981

A preliminary study of relaxation methods for the inviscid conservative gasdynamics equations using flux splitting

Plus minus flux vector split schemes are combined with the multigrid relaxation method to obtain fast rates of iterative (or steady state) convergence. On model nonlifting biconvex airfoil flow, steady state convergence is obtained using multigrid in 40 iteractions for subsonic cases and in 120 iterations for transonic cases. A 65 x 33 stretched grid is used. However, the multigrid scheme used here (and there are numerous variations) sometimes could not be made to work for transonic cases with a large number of supersonic points. Moreover, the multigrid method is only several times faster than the conventional algorithm which itself could perhaps be accelerated by other means. Nethertheless, with proper adjustment the multigrid method will ultimately lead to very fast rates of iterative convergence.

Steger, J. L.↗