SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Aerodynamic coefficients from observed motion of body in flight, eliminating need for closed form solutions by employing numerical solutions to equations of motion
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Skin temperatures and surface pressures have been measured on a slightly blunted cone-cylinder-flare configuration to a maximum Mach number of 9.89 with a rocket-propelled model. The cone had a t o t a l angle of 25 deg and the flare had a 10 deg half-angle. Temperature data were obtained at eight cone locations, four cylinder locations, and seven flare locations; pressures were measured at one cone location, one cylinder location, and three flare locations. Four stages of propulsion were utilized and a reentry type of trajectory was employed in which the high-speed portion of flight was obtained by firing the last two stages during the descent of the model from a peak altitude of 99,400 feet. The Reynolds number at peak Mach number was 1.2 x 10(exp 6) per foot of model length. The model length was 6.68 feet. During the higher speed portions of flight, temperature measurements along one element of the nose cone indicated that the boundary layer was probably laminar, whereas on the opposite side of the nose the measurements indicated transitional or turbulent flow. Temperature distributions along one meridian of the model showed the flare to have the highest temperatures and the cylinder generally to have the lowest. A maximum temperature of 970 F was measured on the cone element showing the transitional or turbulent flow; along the opposite side of the model, the maximum temperatures of the cone, cylinder, and flare were 545 F, 340 F, and 680 F, respectively, at the corresponding time.
Wind tunnel, gliding, and deployment tests of all-flexible, single keel and double keel parawing models
Aerodynamic coefficients from observed motion of body in flight, eliminating need for closed form solutions by employing numerical solutions to equations of motion
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
To assess the possibility of achieving extensive laminar flow on conical vehicles during hyperbolic entry, the Ames Research Center has had an ongoing program to study boundary-layer transition on ablating cones. Boundary layer transition results are presented from ballistic range experiments with models that ablated at dimensionless mass transfer rates comparable to those expected for full scale flight at speeds up to 17 km/sec. It was found possible to measure the surface recession and hence more accurately identify regions of laminar, transitional, and turbulent flow along generators of the recovered cones. Some preliminary results using this technique are presented.
Two blunt-nosed conical configurations were investigated at hypersonic velocities to observe the effect of several gas mixtures on their drag and stability characteristics.
Ten disk-shaped models of a proposed nuclear heat source module were released from an aircraft and observed by radar. The initial launch attitude, spin rate, and mass of the models were varied. Significant differences were observed in the mode of flight and terminal velocity among models of different mass and launch attitudes. The data were analyzed to yield lift and drag coefficients as a function of Reynolds number. The total sea-level velocity of the models was found to be well correlated as a function of mass per unit frontal area. The demonstrated terminal velocity of the modular disk heat source, about 27 m/sec for this specific design, is only 33% of that of existing heat source designs.
The stability and control characteristics of a four-engine turbofan STOL transport model having an externally blown jet flap have been investigated by means of the flying-model technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated under conditions of symmetric and asymmetric (one engine inoperative) thrust at lift coefficients up to 9.5 and 5.5, respectively. Static characteristics were studied by conventional power-on force tests over the flight-test angle-of-attack range including the stall. In addition to these tests, dynamic longitudinal and lateral stability calculations were performed for comparison with the flight-test results and for use in correlating the model results with STOL handling-qualities criteria.
Tests were made in the Langley full-scale tunnel and included a study of the stability and control characteristics of delta- and swept-wing configurations from hovering through the transition to normal forward flight. Static force tests were also conducted to aid in the analysis of the flight tests. With conventional artificial rate stabilization, very smooth transitions could be made consistently with relatively little difficulty. Because of the lower apparent damping and a tendency to diverge in yaw, however, the swept-wing configuration was considered to be much more difficult to fly than the delta-wing configuration. With rate dampers off, both configurations were very difficult to control and the control power needed for satisfactory flights was substantially higher than with the rate dampers operating.
Details of the generation of the separation trajectories are discussed. The analysis culminated in definition of separation trajectories between physical separation and orbiter/carrier vortex clearance. Specifications, assumptions and analytical approach used to generate the separation trajectories are presented. Results of the analytical approach are evaluated. Conclusions and recommendations are summarized. Supporting references are listed.
Explore the source record for details and available documents.
Explore the source record for details and available documents.