Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fusion device”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Variable magnetic field electron spectrometer to measure hot electrons in the range of 50–460 keV

Resonance absorption (RA) occurs when a p-polarized electromagnetic wave, obliquely incident on an inhomogeneous plasma, tunnels past its turning point and resonantly excites an electron plasma wave (EPW) at the critical density. This phenomenon is important, for instance, in the direct drive approach to inertial fusion energy and is a particular example of a wider phenomenon in plasma physics known as mode conversion, which is crucial for heating magnetic fusion devices, such as tokamaks, via RF heating. Direct measurement of these RA-generated EPW accelerated hot electrons, with energy in the range of a few tens to a few hundreds of keV, is a challenging task due to the relatively low deflecting magnetic fields needed. The solution described here is a magnetic electron spectrometer (MES) with a continually changing magnetic field, lower at the entrance of the MES and gradually increasing toward the end, that enables the measurement of a wide spectral range of electrons with energies between 50 and 460 keV. Electron spectra taken in a LaserNetUS RA experiment were acquired from plasmas generated by irradiating polymer targets with the combination of an ~300 ps pulse followed by a series of ten high intensity 50–200 fs duration laser pulses from the ALEPH laser at Colorado State University. In conclusion, the high intensity beam is designed as spike trains of uneven duration and delay pulses in order to modify the RA phenomenon.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Validity condition for the local sheath impedance boundary condition and a nonlocal generalization

ICRF sheaths can cause unwanted interactions of high-power RF waves with material surfaces in magnetic fusion devices. In previous work, a local RF sheath impedance boundary condition (BC) was derived for use in ICRF codes together with a microscale (i.e., Debye or sheath width scale) model for obtaining the sheath impedance used in that BC. This local RF sheath BC matches the normal component of current and electrostatic potential across the sheath-plasma interface. Collapsing the matching conditions at the sheath-plasma interface to a BC depends on the assumption of scale separation, which can be violated when conditions along the local radius of curvature of the surface vary sufficiently rapidly. The validity condition is explored in this contribution, with special attention to the case where the magnetic field approaches being tangent to the surface. When the local sheath BC no longer applies, a non-local sheath BC is developed under the assumption of a more relaxed scale separation assumption. It is shown that the non-local sheath BC reduces to the previous local sheath BC under appropriate conditions. Furthermore, a surface-integrated sheath admittance parameter describes the 2D physics in the new BC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A constrained-transport embedded boundary method for compressible resistive magnetohydrodynamics

Motivated by the increased interest in pulsed-power magneto-inertial fusion devices in recent years, we present a method for implementing an arbitrarily shaped embedded boundary on a Cartesian mesh while solving the equations of compressible resistive magnetohydrodynamics. The method is built around a finite volume formulation of the equations in which a Riemann solver is used to compute fluxes on the faces between grid cells, and a face-centered constrained transport formulation of the induction equation. The small time step problem associated with the cut cells is avoided by always computing fluxes on the faces and edges of the Cartesian mesh. We extend the method to model a moving interface between two materials with different properties using a ghost-fluid approach, and show some preliminary results including shock-wave-driven and magnetically-driven dynamical compressions of magnetohydrostatic equilibria. In conclusion, we present a thorough verification of the method and show that it converges at second order in the absence of discontinuities, and at first order with a discontinuity in material properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

X-ray sources for in situ wavelength calibration of x-ray imaging crystal spectrometers

X-ray sources for a range of wavelengths are being considered for in situ calibration of X-ray Imaging Crystal Spectrometers (XICSs) and for monitoring line shifts due to changes in the crystal temperature, which can vary during experimental operation over a day [A. Ince-Cushman et al., Rev. Sci. Instrum. 79, 10E302 (2008), L. Delgado-Aparicio et al., Plasma Phys. Control. Fusion 55, 125011 (2013)]. Such crystal temperature dependent shifts, if not accounted for, could be erroneously interpreted as Doppler shifts leading to errors in plasma flow-velocity measurements. The x-ray sources encompass characteristic x-ray lines falling within the wavelength range of 0.9–4.0 Å, relevant for the XICSs on present and future fusion devices. Several technological challenges associated with the development of x-ray sources for in situ calibration are identified and are being addressed in the design of multiple x-ray tubes, which will be installed inside the spectrometer housing of the XICS for the JT-60SA tokamak. These x-ray sources will be especially useful for in situ calibration between plasma discharges. Here, in this paper, laboratory experiments are described that were conducted with a Cu x-ray source, a heated quartz (102) crystal, and a pixelated Pilatus detector to measure the temperature dependent shifts of the Cu Kα 1 and Kα 2 lines at 1.5405 and 1.5443 Å, respectively, and to evaluate the 2d-lattice constant for the Bragg reflecting crystal planes as a function of temperature, which, in the case of in situ wavelength calibration, would have to be used for numerical analysis of the x-ray spectra from the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Expanded capabilities of the CarMa code in modeling resistive wall mode dynamics with 3-D conductors

In this work, an improved version of the CarMa code is presented, called CarMa-D, for the analysis of resistive wall modes (RWMs) in fusion devices, simultaneously considering the effects of volumetric three-dimensional conducting structures, plasma dynamics, toroidal rotation or drift-kinetic damping. Unlike static CarMa, CarMa-D does not rely on the simplifying assumptions such as neglecting the plasma mass, toroidal rotation and kinetic damping. The new coupling strategy is based on matrix-based Padé rational functions approximation of plasma a response. The arising mathematical model is formally equivalent to the original CarMa model, but with a higher number of degrees of freedom to model the dynamics of the plasma. CarMa-D overcomes the main limitations of the original CarMa, in particular: (i) the massless assumption for the plasma is removed, allowing modeling of global modes growing both on ideal kink time scales and in the typical RWM growth rate regime, with a suitable treatment of the model; (ii) the effects of toroidal plasma flow and drift kinetic damping can be included into the new model, providing a powerful tool to study macroscopic phenomena where both plasma dynamics and 3-D conducting structures play important roles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Thermohydraulic Design Analysis of the Target Assembly in the Material Plasma Exposure Experiment Facility

The Material Plasma Exposure eXperiment (MPEX) project seeks to design a steady-state linear plasma facility at Oak Ridge National Laboratory that will be used to study plasma-material interactions (PMIs) at fusion prototypic levels, supporting the evaluation and development of materials for the next generation of fusion devices. This study is focused on PMI exposure of small-size neutron-irradiated specimens, which are clamped onto an actively cooled component. A thermohydraulic evaluation of a new MPEX target assembly design to assess the appropriate operation during MPEX operation is presented. To further guide the design and assess the structural integrity of the components under expected loads, preliminary thermomechanical stress analyses were also conducted. To ensure good thermal contact between the components, thermal interface materials, such as silver flexible graphite, were used in the assembly. It was found that the maximum target temperatures of 1572, 1463, and 1315 K were obtained for Grafoil thicknesses of 0.61, 0.38, and 0.25 mm, respectively. The distribution of the axial deformation at high heat fluxes showed that there are no gaps between components, indicating good contact at material interfaces. Moreover, the contact pressure between the target and other components indicated that very good contact was established at these interfaces. Furthermore, the stress-strain conditions for the target will be further used to assess the appropriate operation during MPEX experiments and gain insight into materials science phenomena during PMI experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Validation of theory-based models for the control of plasma currents in W7-X divertor plasmas

A theory-based model for the control of plasma currents for steady-state operation in W7-X is proposed and intended for model-based plasma control. The conceptual outline implies the strength of physics-based models: it offer approaches applicable to future conditions of fusion devices or next-step machines. The application at extrapolated settings is related to the validity range of the theory model. Therefore, the predictive power of theory-based control models could be larger than for data-driven approaches and limitations can be predicted from the validity range for the prediction of bootstrap currents in W7-X. The model predicts the L/R response when density or heating power is changed. The model is based on neoclassical bootstrap current calculations and validated for different discharge conditions. While the model was found to be broadly applicable for conducted electron-cyclotron-heated discharges in W7-X, limits were found for cases when the polarization of the electron cyclotron heating was changed from X2 to O2-heating. The validity assessment attempts to quantify the potential of the derived model for model-based control in the operational space (density, heating power) of W7-X.

neoclassical modelling↗
DOE OSTI2025

Effects of oxidation and impurities in lithium surfaces on the emitting wall plasma sheath

The use of lithium as a surface coating in fusion devices improves the plasma performance, but the change in the wall properties affects the secondary electron emission properties of the material. Lithium oxidizes easily, which drives the emission yield well above unity. We present here simulations demonstrating the change in the sheath structure from monotonic to the nonmonotonic space-charge limited sheath using an energy-dependent data-driven emission model, which self-consistently captures both secondary emission and backscattering populations. Increased secondary electron emission from the material has ramifications for the degradation and erosion of the wall. The results show that the oxidation leads to an increased electron energy flux into the wall and a reduced ion energy flux. The net transfer of energy to the surface is significantly greater for the oxidized case than for the pure lithium case. High backscattering rates of low-energy particles lead to a high re-emission rate at the wall.

Fusion reactors↗
DOE OSTI2022

Orbit tomography of energetic particle distribution functions

Both fast ions and runaway electrons are described by distribution functions, the understanding of which are of critical importance for the success of future fusion devices such as ITER. Typically, energetic particle diagnostics are only sensitive to a limited subsection of the energetic particle phase-space which is often insufficient for model validation. However, previous publications show that multiple measurements of a single spatially localized volume can be used to reconstruct a distribution function of the energetic particle velocity-space by using the diagnostics' velocity-space weight functions, i.e. velocity-space Tomography. In this work we use the recently formulated orbit weight functions to remove the restriction of spatially localized measurements and present orbit tomography, which is used to reconstruct the 3D phase-space distribution of all energetic particle orbits in the plasma. Through a transformation of the orbit distribution, the full energetic particle distribution function can be determined in the standard {energy, pitch, r, z}-space. We benchmark the technique by reconstructing the fast-ion distribution function of an MHD-quiescent DIII-D discharge using synthetic and experimental FIDA measurements. We also use the method to study the redistribution of fast ions during a sawtooth crash at ASDEX upgrade using FIDA measurements. Lastly, a comparison between the orbit tomography and velocity-space tomography is shown.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Effect of Magnetic Islands on Neoclassical Heat Diffusivity in a Global Tokamak Simulation

Resonant magnetic perturbations (RMPs) alter magnetic field topology via island formation and can modify core transport in toroidal fusion devices. Using the global gyrokinetic particle‐in‐cell code XGC‐S, originally developed for stellarator geometries, we quantify how island topology affects neoclassical heat transport in a circular tokamak with ($m,n$) = (5,2) RMP‐induced islands. Electron radial heat diffusivity exhibits a two‐peak structure with a dominant enhancement near the O/X‐point region and a secondary peak at the outer island boundary, whereas ion transport remains close to the neoclassical prediction. The observed electron diffusivity is strongly enhanced over the neoclassical baseline but remains well below the Rechester–Rosenbluth estimate, consistent with the non‐ergodic character of the island topology. The density dependence of diffusivity is weaker inside the islands than outside, indicating the presence of topology‐driven transport channels that do not depend strongly on collisionality. Two‐dimensional heat flux maps reveal an up–down antisymmetric structure at the island separatrices consistent with magnetic gradient and curvature drift effects, in contrast to the symmetric temperature flattening inside the islands. These results identify topology‐dependent avenues for electron heat transport in RMP‐perturbed cores and suggest regimes in which island geometry, rather than collisions alone, governs radial transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Thermal Hydraulics Analysis of a Divertor Monoblock Using SALAMANDER

Divertors are critical components in magnetic confinement fusion devices. One of the Divertor's crictial roles is absorbing the highest heat flux from the plasma. The Divertor accomplishes this through the use of divertor monoblocks and cooling channels. This work presents a thermal hydraulic analysis of a divertor monoblock using the Software for Advanced Large-scale Analysis of MAgnetic confinement for Numerical Design, Engineering and Research (SALAMANDER). SALAMANDER is an open source tool developed at Idaho National Laboratory for conducting multiphysics and multscale analysis of Plasma Facing Components (PFCs). For the monoblock, solid heat conduction is modeled in the block with a constant heat flux of 1E7 W/m^2 applied to the top of the block to represent peak heat flux from the plasma. The cooling channel (which is pressurized water at a Reynolds number of ~1,000,000) is modeled using a k-epsilon turbulence model with standard wall functions. The heat transfer between the solid and fluid domain is modeled using the Dittus-Boelter correlation for the convective heat transfer coefficient. This work aims to show the importance of a multiphysics modeling approach when performing simulations on PFCs.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Full wave modeling of radio-frequency beams in tokamaks in the electron cyclotron frequency range

Simulation of full wave, without paraxial approximation, high-resolution solution of wave equations in frequency domain in the electron cyclotron resonance (ECR) frequency range for realistic Tokamak plasma parameters became possible by using recently formulated hybrid iterative algorithm [Svidzinski et al., Phys. Plasmas 25, 082509 (2018)] for numerically solving discretized wave equations. This approach combines time evolution and iterative relaxation techniques into iteration cycles. This algorithm is implemented in 2D code FullWave, solving wave equations in Tokamaks in cold and hot plasma models, and it has been tested in 3D full wave iterative RF beams simulation tool, which is presently being developed to model 3D ECRH RF beams in fusion devices using dynamic grid adaptation. The results of 2D full wave modeling, assuming specified toroidal mode number, of ECRH RF beams in DIII-D plasma, performed in the cold and hot plasma models for outboard and top launch scenarios using FullWave are presented. Nonlocal hot plasma response model, based on accurate numerical solution of linearized Vlasov equation, is used to model beam propagation and absorption in the 2nd electron cyclotron harmonic region. Demonstration of capability of the hybrid iterative algorithm to model ECRH RF beams in 3D is made by simulating a substantial part of realistic beam in DIII-D, launched from outboard side of the machine. All relevant physics of RF beam propagation, most of which is not captured in paraxial approximation, such as beam's divergence, interference between the X and O modes in the beam, X-O mode conversion, beam splitting into the X and O mode beams, transformation of beam's cross section, and absorption at the 2nd electron cyclotron harmonic, is captured in the simulations. A numerical technique to find an optimal beam polarization at the launcher to launch a nearly pure X or O mode beam in plasma is developed and tested.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Sparsified time-dependent Fourier neural operators for fusion simulations

This paper presents a sparsified Fourier neural operator for coupled time-dependent partial differential equations (ST-FNO) as an efficient machine learning surrogate for fluid and particle-based fusion codes such as NIMROD (Non-Ideal Magnetohydrodynamics with Rotation - Open Discussion) and GTC (Gyrokinetic Toroidal Code). ST-FNO leverages the structures in the governing equations and utilizes neural operators to represent Green's function-like numerical operators in the corresponding numerical solvers. Once trained, ST-FNO can rapidly and accurately predict dynamics in fusion devices compared with first-principle numerical algorithms. In general, ST-FNO represents an efficient and accurate machine learning surrogate for numerical simulators for multi-variable nonlinear time-dependent partial differential equations, with the proposed architectures and loss functions. The efficacy of ST-FNO has been demonstrated using quiescent H-mode simulation data from NIMROD and kink-mode simulation data from GTC. The ST-FNO H-mode results show orders of magnitude reduction in memory and central processing unit usage in comparison with the numerical solvers in NIMROD when computing fields over a selected poloidal plane. The ST-FNO kink-mode results achieve a factor of 2 reduction in the number of parameters compared to baseline FNO models without accuracy loss.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

2-D moving mesh modeling of lithium dryout in open surface liquid metal flow applications

Liquid lithium displays increasing promise as a replacement for solid plasma facing components (PFCs) in fusion device applications. The Liquid Metal Infused Trench (LiMIT) system, developed at the University of Illinois (UIUC), has demonstrated how thermoelectric magnetohydrodynamics (TEMHD) can be harnessed to drive liquid lithium flow in an open surface PFC. However, in the highest heat flux applications, large local acceleration is created via TEMHD, and the sudden increase in velocity can cause the liquid level to expose the underlying solid, eliminating the protective benefits of the lithium. In order to study potential mitigation strategies, a 2-D COMSOL Multiphysics model was developed using the moving mesh module to capture free surface flow. The model depicts the development of the dryout phenomenon for 2 test cases – slow (1 cm/s) and medium (10 cm/s) flow in 5 mm deep trenches – including the liquid level reduction under the high heat flux and the pileup of slower flow both upstream and downstream of the heat stripe. The effectiveness of trench shaping dryout mitigation strategies is examined. For the slow flow case, it is shown that a 1.8 mm ledge placed under the heat stripe will stop dryout, and for the medium flow case, a 2.7 mm ledge is required to mitigate the effect. This model can be used to identify strategies for increasing the viable heat load for open surface liquid lithium PFCs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Anomalous losses of energetic particles in the presence of an oscillating radial electric field in fusion plasmas

The confinement of energetic particles in nuclear fusion devices is studied in the presence of an oscillating radial electric field and an axisymmetric magnetic equilibrium. Here, it is shown that, despite the poloidal and toroidal symmetries, initially integrable orbits turn into chaotic regions that can potentially intercept the wall of the tokamak, leading to particle losses. It is observed that the losses exhibit algebraic time decay different from the expected exponential decay characteristic of radial diffusive transport. A dynamical explanation of this behaviour is presented, within the continuous time random walk theory. The central point of the analysis is based on the fact that, contrary to the radial displacement, the poloidal angle is not bounded and a proper statistical analysis can therefore be made, showing for the first time that energetic particle transport can be super-diffusive in the poloidal direction and characterised by asymmetric poloidal displacement. The connection between poloidal and radial positions ensured by the conservation of the toroidal canonical momentum, implies that energetic particles spend statistically more time in the inner region of the tokamak than in the outer one, which explains the observed algebraic decay. This indicates that energetic particles might be efficiently slowed down by the thermal population before leaving the system. Also, the asymmetric transport reveals a new possible mechanism of self-generation of momentum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Microstability of β ~ 1 tokamak equilibria

High-power-density tokamaks offer a potential solution to design cost-effective fusion devices. One way to achieve high power density is to operate at a high β value (the ratio of thermal to magnetic pressure), i.e. β~1 . However, a β~1 state may be unstable to various pressure- and current-driven instabilities or have unfavourable microstability properties. To explore these possibilities, we generate β~1 equilibria and investigate their stability. First, we demonstrate the generation of high-β equilibria with the computer code VMEC. We then analyse these equilibria to determine their stability against the infinite-n ideal-ballooning mode. We follow that by engaging in a detailed microstability study using the GS2 code, beginning with assessments of electrostatic ion-temperature-gradient and trapped election mode instabilities. We observe interesting behaviour for the high-β equilibria – stabilization of these modes through two distinct mechanisms – large negative local shear and reversal of electron precession drift. Finally, we perform electromagnetic gyrokinetic simulations and observe enhanced stability in the outer core of high-β equilibria and absence of kinetic ballooning modes in the negative-triangularity, high-β equilibria. The enhanced outer-core stability of high-β equilibria is different from their lower-β counterparts and offers an alternative, potentially favourable regime of tokamak operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Developing the hybrid scenario in DIII-D and KSTAR for W-compatible long-pulse operation

Long-pulse, high-performance operation with tungsten plasma-facing components is a crucial challenge for achieving steady-state (SS) goals in ITER and future fusion devices. This paper presents a joint international effort between the DIII-D and KSTAR tokamaks aimed at demonstrating the compatibility of the high q 95 ~ 6 hybrid scenario with a tungsten divertor and superconducting coils. A DIII-D hybrid scenario recipe is successfully tailored to KSTAR’s operational constraints, which facilitates cross-device studies. The results show successful 30 s long-pulse operation in KSTAR at a normalized beta (β N = 2.4) with a benign m/n = 4/3 mode and effective mitigation of tungsten accumulation. Despite this success, the KSTAR scenario exhibits a greater than 25% reduction in thermal confinement compared to the DIII-D reference. To investigate this discrepancy, we performed a predictive TGYRO validation study, which suggests that the difference is likely caused by a weaker temperature pedestal in the KSTAR discharge due to a higher and narrower density pedestal. In addition, such lower thermal confinement leads to higher impurity accumulation, possibly due to a change in neoclassical transport with increased inward pinch, which further degrades global confinement. We also report that stationary, long-pulse operation with sustained thermal confinement requires consistent fueling and wall conditioning. These findings highlight the importance of optimized fueling and real-time wall conditioning in achieving a high temperature pedestal and strong global confinement during stable long-pulse operation. We propose potential approaches toward fully SS, long-pulse operation, including real-time wall conditioning using an impurity dropper in KSTAR and future tokamaks.

DIII-D↗
DOE OSTI2020

Verification of an improved equation-free projective integration method for neoclassical plasma-profile evolution in tokamak geometry

A brute-force, long-time gyrokinetic simulation of plasma profile evolution in magnetic fusion devices is not desirable due to large computational resource requirements and a possible accumulation of numerical error. The equation-free projective integration method of Keverekidis et al. [Commun. Math. Sci. 1(4), 715–762 (2003)] is one of the outstanding candidates in projecting micro-scale simulations to a longer timescale. However, its application to tokamak plasma has not been fruitful due to the appearance of spurious transient oscillations in the lifting process, which are present when the kinetic simulations are initialized with a simplified model distribution function and which make the kinetic simulations to deviate from the desired paths. In this work, a kinetically informed lifting algorithm is added to the equation-free projective integration method, which is then verified in the electrostatic gyrokinetic particle-in-cell code XGCa [R. Hager and C. S. Chang, Phys. Plasmas 23, 042503 (2016)] for a neoclassical ion heat transport problem with adiabatic electrons. This new lifting operator is demonstrated to control spurious transients, enabling an over four-times reduction in the overall computing time in the time-evolution of the ion temperature profile in an axisymmetric toroidal plasma. Further reduction in the computing time is found to be limited due to the stability properties of the linear least squares projective integrator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗