Search NASA⌕ Search

SEARCH · Search NASA

Results for “GLASS FIBER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Infrared thermography NDT for in-situ defect detection in sandwich composite panel manufacturing

Composite manufacturing presents numerous challenges, as defects can arise from various sources throughout the process. In sandwich composite structures, the integration of a foam core introduces additional complexity and increases the likelihood of defect formation like delamination. To mitigate these issues and reduce the risk of future structural failures, in-situ monitoring during manufacturing is essential. This study investigates infrared (IR) thermography as a non-destructive technique for detecting manufacturing defects in foam-core sandwich composite panels under thermally excited conditions representative of in-situ processing. A stationary FLIR A8590 IR camera (640 × 512 pixels, 30Hz, 17mm lens, 9 ft stand-off distance) was used to monitor prefabricated panels subjected to controlled external heating simulating compression molding and resin cure exotherm. Interlaminar delamination defects with characteristic sizes ranging from 0.25 × 0.25in² to 5 × 5in² produced measurable surface temperature depressions of approximately 4–10°C during transient cooling, exceeding the effective noise floor of the camera by more than two standard deviations. Thicker laminates exhibited prolonged defect detectability windows due to increased thermal diffusion time. In contrast, embedded Teflon inclusions generated weak thermal contrasts of ≤ 3°C, approaching the measurement noise floor, due to limited thermal property contrast with the surrounding glass fiber composite. These results establish quantitative detectability limits for stationary thermographic inspection of sandwich composite panels under manufacturing-representative thermal cycles.

Barakat, Abdallah [ORNL] (ORCID:0000000296141398)↗
DOE OSTI2025

Electrolyte Compatible Separator Materials for Sodium-Ion Battery

Sodium-ion batteries (NIBs) have emerged as an alternative electrochemical energy storage to replace lithium-ion batteries (LIBs). Separator is one of the key components that dictates the cell performance of NIB. Significant progress has been made in electrolyte research, however for most cases glass fiber has been used as separator due to its remarkable electrolyte wettability despite its many disadvantages. In this study, we evaluated commercially available porous materials as separator material for NIB. Porous polyvinylidene fluoride (PVDF) membrane stands out as a universal separator which exhibits high compatibility with a wide range of electrolytes and electrodes and demonstrates high electrochemical stability evaluated in hard carbon/Na half cells and NaNi 1/3 Fe 1/3 Mn 1/3 O 2 (NFM111)/hard carbon full cells. This research highlights the PVDF membrane as a viable separator for advancing NIB research, enabling the development of new electrolyte materials without the separator constraints of wetting limitations or excessive electrolyte consumption.

Wostoupal, Owen S. [Argonne National Laboratory (A↗
DOE OSTI2024

Numerical modeling and experimental validation of low velocity impact of woven GFRP/CFRP composites

Low-velocity impact of 2D woven glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) composite laminates was studied experimentally and numerically. Hybrid laminates containing blocked layers of GFRP/CFRP/GFRP with all plies oriented at 0° were investigated. Relatively high impact energies were used to obtain full perforation of the laminate in a low-velocity impact setup. Numerical simulations were carried out using the in-house transient dynamics finite element code, Sierra/SM, developed at Sandia National Laboratories. A three-dimensional continuum damage model was used to describe the response of a woven composite ply. Two methods for handling delamination were considered and compared: (1) cohesive zone modeling and (2) continuum damage mechanics. The reduced model size achieved by omission of the cohesive zone elements produced acceptable results at reduced computational cost. Further, the comparison between different modeling techniques can be used to inform modeling decisions relevant to low velocity impact scenarios. The modeling was validated by comparing with the experimental results and showed good agreement in terms of predicted damage mechanisms and impactor velocity and force histories.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Scalable Fabrication of a Fibrous Amine-functionalized Matrix (FAM) Sorbent for Critical Mineral Recovery

We report a novel flat sheet Fibrous Amine-functionalized Matrix (FAM) sorbent platform designed for efficient and selective capture of CM from dilute solutions. The FAM sorbent features crosslinked amine microfilms coated onto/within a glass fiber matrix, providing fast mass transfer and excellent mechanical stability. Systematic batch and flow-through tests with FAM revealed rapid metal uptake kinetics and high capacity for representative species, achieving ~90 mg/g of Gallium, ~100 mg/g of Cobalt, and ~90 mg/g for Neodymium. Moreover, multiple eluents, including mineral acids and complexing agents, enabled highly effective desorption of adsorbed metals, demonstrating the feasibility of regenerating FAM sorbents. Importantly, tests with authentic coal ash leachate demonstrated strong selectivity toward U.S. Department of Energy (DOE)-listed CM and rare earth elements over abundant base cations, confirming the robustness of FAM in realistic complex solutions. The flat sheet geometry was amenable to scaling into durable spiral wound modules, highlighting the potential for future regeneration and reuse. This work establishes FAM sorbents as a promising platform for the recovery of CM from wastewaters, advancing both resource sustainability and environmental stewardship.

critical mineral recovery↗
DOE OSTI2024

Lignin content of Populus trichocarpa residues after CELF pretreatment and CBP fermentation

Here we present a dataset of lignin content from a woody energy crop (Populus trichocarpa) residues after a series of co-solvent enhanced lignocellulosic fractionation (CELF) pretreatment and consolidated bioprocessing (CBP) process. The natural poplar variant GW-9947 from the Center for Bioenergy Innovation (CBI) was used. The poplar was knife milled and passed through a 1 mm sieve and CELF pretreatment was performed in a Parr autoclave reactor with 7.5 wt % solids loading, 0.5 wt% H2SO4 as catalyst at 150°C with 5, 15, 25 and 30 minutes, respectively. Tetrahydrofuran was added in a 1:1 mass ratio with water as the pretreatment solvent. The residues from CELF pretreatment were then subjected to CBP using the bacterium C. thermocellum DSM 1313. CBP fermentations were performed at 60 °C in a shaker at 50, 75, and 100 grams/L solids loadings. The Klason lignin was measured using a two-step acid hydrolysis process. In brief, the poplar samples were first hydrolyzed by 72 wt% sulfuric acid at 30 oC for an hour. The hydrolysates were then diluted to 4 wt% sulfuric acid using deionized water and subsequently autoclaved at 121 oC for 1 h. Upon the completion of the two-step hydrolysis, the resulting solution was cooled to room temperature and the precipitate was then filtered through a G8 glass fiber filter through a crucible, dried at oven for overnight, and weighed to get the Klason lignin content. The lignin data provides information about lignin content changes after CELF and C. thermocellum CBP process.

Lignin Populus trichocarpa CELF pretreatment CBP f↗
NASA NTRS1964

Integral coolant channels supply made by melt-out method

Melt-out method of constructing strong, pressure-tight fluid coolant channels for chambers is accomplished by cementing pins to the surface and by depositing a melt-out material on the surface followed by two layers of epoxy-resin impregnated glass fibers. The structure is heated to melt out the low-melting alloy.

Escher, W. J. D.↗
NASA NTRS1966

Insulation for cryogenic tanks has reduced thickness and weight

Dual seal insulation, consisting of an inner layer of sealed-cell Mylar honeycomb core and an outer helium purge channel of fiber glass reinforced phenolic honeycomb core, is used as a thin, lightweight insulation for external surfaces of cryogenic-propellant tanks.

Dumire, P. E.↗
NASA NTRS1967

Inexpensive cryogenic insulation replaces vacuum jacketed line

Commercially available aluminized Mylar, cork and fiber glass form a multilayered sealed system and provide rugged and economical field installed insulation for cryogenic /liquid nitrogen or oxygen/ pipe lines in an exposed environment.

Fuchs, C. E.↗