Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geared”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Magnetic Gears and Their Structural Limitations

Magnetic gears present significant structural design challenges, because metallic/electrically conductive structures are highly undesirable as they would lead to significant efficiency reductions. Additionally, most non-electrically conductive structural materials have low thermal conductivity, which makes cooling the gear difficult. These limitations are of particular significant in magnetic gear's modulator structures. NASA Glenn has shown that pole pieces on the order of 1 to 2 mm thick optimize magnetic gears specific torque. These thin pole pieces however see very large magnetic forces and modulator structural limitations prevent the use of magnetically optimum pole pieces. The best solution to this issue to date has been the use of carbon fiber retaining rings on the external surface of the modulator, however this solution increases ring modulator airgap, resulting in a torque reduction from the optimum design. The pole pieces are also the largest sources of losses in magnetic gears. Because the modulator is nestled between the ring and sun gear extraction of this heat is a difficult problem and the modulator structure has to be designed to dissipate this heat load. In the presentation I will present the design of NASA Glenn's 4th magnetic gear's modulator in detail that uses a combination of 3D fiber reinforced nylon, IM7 carbon fiber, and pitch base cn80 fiber to close both structurally and thermally.

Tallerico, Thomas↗
NASA NTRS2019

Static Torsion Testing and Modeling of a Variable Thickness Hybrid Composite Bull Gear

Torsional strength of a variable thickness hybrid gear web was measured by performing static testing on the part in a large torsion test frame. The outer rim of the hybrid gear web was fixed to the bottom of the test frame and loading was applied to the web through a shaft. The test setup included the installation of digital image correlation (DIC) systems to obtain deformation and strain measurements from the surfaces of the hybrid gear web and the mechanical test equipment to ensure reliability of the test. The results indicated that the variable thickness hybrid gear web achieved approximately twice the torsional strength compared to that of previous hybrid gear designs. The DIC analysis showed significantly more straining of the loading shaft than the actual test article. Additionally, the results demonstrated the importance and affect that the metallic, lobed interlock features had on the principal strain and out-of-plane displacement fields. The analysis revealed that the fixed outer rim was in fact rotating and a rigid body motion compensation (RBMC) function was computed to determine the actual rotation of the hub and composite web relative to the outer rim. Modeling simulations were performed for the variable thickness hybrid gear web and correlated well with the RBMC rotational deformation seen in the DIC analysis. In addition to benchmarking the load capacity of the hybrid gear web, measuring its strength is useful information to define the parameters needed for dynamic, endurance, and other testing of the part.

Johnston, Joel P.↗
NASA NTRSDate not supplied

Design Study of a Coupled Inner-Stator Magnetically Geared Motor for Electric Aircraft Applications

Electric aircraft require high performance and high reliability electric motor drivetrains. A geared electric motor drivetrain will outperform a direct drive motor drivetrain in most applications. Traditional mechanical gearing, however, has mechanical contact-based wear and failure modes that result in added maintenance costs and require an oil lubrication system. Magnetically geared motor drives are a potential technology for electric aircraft applications capable of enabling the benefits of a geared drive without the maintenance, reliability, and lubrication system cost of mechanical gears. In this paper, a topology of magnetically geared motor, an inner stator magnetically geared motor, is explored to estimate its achievable performance for electric aircraft applications. Optimization results on the topology show that it can achieve greater than 15 Nm/kg and 96% efficiency at 100 kW of power.

Thomas Tallerico↗
NASA NTRSDate not supplied

Design Study of a Coupled Inner-Stator Magnetically Geared Motor for Electric Aircraft Applications

Abstract- Electric aircraft require high performance and high reliability electric motor drivetrains. A geared electric motor drivetrain will outperform a direct drive motor drivetrain in most applications. Traditional mechanical gearing, however, has mechanical contact-based wear and failure modes that result in added maintenance costs and require an oil lubrication system. Magnetically geared motor drives are a potential technology for electric aircraft applications capable of enabling the benefits of a geared drive without the maintenance, reliability, and lubrication system cost of mechanical gears. In this paper, a topology of magnetically geared motor, an inner-stator magnetically geared motor, is explored to estimate its achievable performance for electric aircraft applications. Optimization results on the topology show that it can achieve greater than 15 Nm/kg specific torque and 96% efficiency at 100 kW of power.

Thomas Tallerico↗
NASA NTRS2003

Modified Involute Helical Gears: Computerized Design, Simulation of Meshing and Stress Analysis

The computerized design, methods for generation, simulation of meshing, and enhanced stress analysis of modified involute helical gears is presented. The approaches proposed for modification of conventional involute helical gears are based on conjugation of double-crowned pinion with a conventional helical involute gear. Double-crowning of the pinion means deviation of cross-profile from an involute one and deviation in longitudinal direction from a helicoid surface. Using the method developed, the pinion-gear tooth surfaces are in point-contact, the bearing contact is localized and oriented longitudinally, and edge contact is avoided. Also, the influence of errors of alignment on the shift of bearing contact, vibration, and noise are reduced substantially. The theory developed is illustrated with numerical examples that confirm the advantages of the gear drives of the modified geometry in comparison with conventional helical involute gears.

COMPUTER AIDED DESIGN↗
NASA NTRS2013

Investigation of Sideband Index Response to Prototype Gear Tooth Damage

The objective of this analysis was to evaluate the ability of gear condition indicators (CI) to detect contact fatigue damage on spiral bevel gear teeth. Tests were performed in the NASA Glenn Spiral Bevel Gear Fatigue Rig on eight prototype gear sets (pinion/gear). Damage was initiated and progressed on the gear and pinion teeth. Vibration data was measured during damage progression at varying torque values while varying damage modes to the gear teeth were observed and documented with inspection photos. Sideband indexes (SI) and root mean square (RMS) CIs were calculated from the time synchronous averaged vibration data. Results found that both CIs respond differently to varying torque levels, damage levels and damage modes

health monitoring↗
NASA NTRS2015

Evaluation of MEMS-Based Wireless Accelerometer Sensors in Detecting Gear Tooth Faults in Helicopter Transmissions

The diagnostics capability of micro-electro-mechanical systems (MEMS) based rotating accelerometer sensors in detecting gear tooth crack failures in helicopter main-rotor transmissions was evaluated. MEMS sensors were installed on a pre-notched OH-58C spiral-bevel pinion gear. Endurance tests were performed and the gear was run to tooth fracture failure. Results from the MEMS sensor were compared to conventional accelerometers mounted on the transmission housing. Most of the four stationary accelerometers mounted on the gear box housing and most of the CI's used gave indications of failure at the end of the test. The MEMS system performed well and lasted the entire test. All MEMS accelerometers gave an indication of failure at the end of the test. The MEMS systems performed as well, if not better, than the stationary accelerometers mounted on the gear box housing with regards to gear tooth fault detection. For both the MEMS sensors and stationary sensors, the fault detection time was not much sooner than the actual tooth fracture time. The MEMS sensor spectrum data showed large first order shaft frequency sidebands due to the measurement rotating frame of reference. The method of constructing a pseudo tach signal from periodic characteristics of the vibration data was successful in deriving a TSA signal without an actual tach and proved as an effective way to improve fault detection for the MEMS.

gears↗
NASA NTRS2016

Advanced Face Gear Surface Durability Evaluations

The surface durability life of helical face gears and isotropic super-finished (ISF) face gears was investigated. Experimental fatigue tests were performed at the NASA Glenn Research Center. Endurance tests were performed on 10 sets of helical face gears in mesh with tapered involute helical pinions, and 10 sets of ISF-enhanced straight face gears in mesh with tapered involute spur pinions. The results were compared to previous tests on straight face gears. The life of the ISF configuration was slightly less than that of previous tests on straight face gears. The life of the ISF configuration was slightly greater than that of the helical configuration.

fatigue↗
NASA NTRS2017

Evaluation of a Variable Thickness Hybrid Composite Bull Gear

For several years, NASA Glenn Research Center and the U.S. Army Research Laboratory have been investigating hybrid (composite/steel) gear technology for use in vertical lift drive systems. The hybrid gear concept replaces the structural portion of a gear between the shaft and the gear rim with a lightweight carbon fiber composite, in an effort to reduce the overall weight of a gear and increase the drive system power density. Past research includes both small-scale and large-scale hybrid gear concepts, all of which have a constant composite thickness throughout. The design described in this paper is of a variable thickness, such that the composite is thickest at the inner diameter and this thickness is gradually reduced toward the outer diameter. The resulting "stair stepped" design stems from dropping plies of the braided carbon fiber prepreg composite fabric gradually with increased radius. Additionally, the interlock pattern at the inner metallic adapter was adjusted slightly from previous designs to obtain a better stress distribution on the inner metallic adapter. The manufactured variable thickness web was tested both in static torsion tests and operationally in a relevant gearbox environment. The results of these experiments will be presented and compared to a baseline steel configuration.

Gears; Drive Systems; Rotorcraft Propulsion;↗
NASA NTRS2019

Lessons Learned in Fabrication of a High-Specific-Torque Concentric Magnetic Gear

Magnetic gearing is being investigated at NASA as a replacement to conventional mechanical gearing in aerospace applications. Some key benefits of magnetic gears over mechanical gearing are torque transmission without mechanical contact, decreased transmission noise, less frequent maintenance, and lack of lubrication. In order to take advantage of these benefits in aerospace applications, magnetic gearing must be shown to provide high enough specific torque (torque per unit mass). Prototype 2 (PT-2), developed to maximize specific torque, and fabricated at NASA Glenn Research Center, has shown promising specific torque comparable to low torque mechanical gears. This work will briefly review the electromagnetic and structural design of PT-2, provide detailed information on fabrication and assembly, examine build errors, walk through rebuild efforts to improve operation, and conclude with remarks on build difficulties and opportunities for improvement in future prototypes.

Electrified Vertical Take Off and Landing↗
NASA NTRS2019

Lessons Learned in Fabrication of a High-Specific-Torque Concentric Magnetic Gear

Magnetic gearing is being investigated at NASA as a replacement to conventional mechanical gearing in aerospace applications. Some potential benefits of magnetic gears over mechanical gearing are torque transmission without mechanical contact, decreased transmission noise, and no required lubrication. However, in order to be a viable alternative for aerospace applications, magnetic gearing must be shown to provide high enough specific torque (torque per unit mass). NASA's second magnetic gearing prototype (PT-2) was able to achieve promising specific torque on par with low torque mechanical gearboxes. This work will briefly review the electromagnetic and structural design of PT-2, provide detailed information on fabrication and assembly, examine build errors, walk through rebuild efforts to improve operation, and conclude with remarks on build difficulties and opportunities for improvement in future prototypes.

Magnetic Gearing↗
NASA NTRS1969

Gear design considerations

This paper discusses the parameters of gears and gear lubrication that affect wear, pitting, and scoring. Formulas for sliding and rolling velocities and for relative radii of profile and lengthwise curvatures between gear teeth are listed. The effects of load sharing between teeth are considered, and formulas for contact stress are developed. The duration of tooth contact and the variation in coefficient of friction are considered. The aspects of oil film thickness and critical temperatures are presented in relation to gear tooth wear and scoring. A discussion of gear testing and simulated gear testing by means of rollers emphasizes the advantages of each.

Coleman, W.↗
NASA NTRS1973

Pitting fatigue characteristics of AISI M-50 and super nitralloy spur gears

Two groups of 3.50-in. pitch-diameter spur gears, without tip relief, made from consumable-electrode vacuum-melted (CVM) AISI M-50 steel and CVM super nitralloy (5Ni-2A1) were tested under conditions which produced fatigue pitting. The M-50 gears had fatigue lives approximately 50 percent longer than the super nitralloy gears. Both groups of gears failed by classical rolling-element fatigue at the pitch circle. When the gears were overrun past initial spall formation, the spalled M-50 gear teeth failed by fatigue fracture. The M-50 material had higher wear than the super nitralloy material. Differences in fatigue life and wear were not considered statistically significant.

Townsend, D. P.↗
NASA NTRS1974

Liquid rocket engine turbopump gears

Design and fabrication of gear drives for rocket engine turbopumps are described in the sequence encountered during the design process as follows: (1) selection of overall arrangement; (2) selection of gear type; (3) preliminary sizing; (4) lubrication system design; (5) detail tooth design; (6) selection of gear materials; and (7) gear fabrication and testing as it affects the design. The description is oriented towards the use of involute spur gears, although reference material for helical gears is also cited.

Source record↗
NASA NTRS1975

Dynamic Capacity and Surface Fatigue Life for Spur and Helical Gears

A mathematical model for surface fatigue life of gear, pinion, or entire meshing gear train is given. The theory is based on a previous statistical approach for rolling-element bearings. Equations are presented which give the dynamic capacity of the gear set. The dynamic capacity is the transmitted tangential load which gives a 90 percent probability of survival of the gear set for one million pinion revolutions. The analytical results are compared with test data for a set of AISI 9310 spur gears operating at a maximum Hertz stress of 1.71 billion N/sq m and 10,000 rpm. The theoretical life predictions are shown to be good when material constants obtained from rolling-element bearing tests were used in the gear life model.

Coy, J. J.↗
NASA NTRS1975

Analysis of dynamic capacity of low-contact-ratio spur gears using Lundberg-Palmgren theory

A concise mathematical model is developed for surface fatigue life of low-contact-ratio spur gears. The expected fatigue life of the pinion, gear, or gear sets may be calculated from the model. An equation for the dynamic capacity of the gear set was also derived in terms of the transmitted tangential tooth load which will give a 10-percent fatigue life of one million pinion revolutions. The theoretical life was compared with experimental data for a set of VAR AISI 9310 gears operating at a Hertz stress of 1.71X10 to the 9th power newtons per square meter (248,000 psi) and 10 000 revolutions per minute. Good agreement was obtained between the experimental and theoretical surface fatigue life of the gears.

Coy, J. J.↗
NASA NTRS1975

Life analysis of helical gear sets using Lundberg-Palmgren theory

A mathematical model is developed for surface fatigue life of helical gears. The expected fatigue life of a pinion, gear, or gear set may be calculated from the model. An equation for the dynamic capacity of a gear set was also derived. Dynamic capacity is the transmitted tangential load which gives a 90 percent probability of survival of the gear set for one million pinion revolutions. The equations, when simplified by setting the helix angle to zero, reduce to the results which were previously developed for spur gears. A sample calculation is given which illustrates the use of the new fatigue life model.

Coy, J. J.↗
NASA NTRS1976

Geared-elevator flutter study

An experimental and analytical study was made of the transonic flutter characteristics of a supersonic transport tail assembly model having an all-movable, horizontal tail with a geared elevator. Two model configurations, namely, one with a gear-elevator (2.8 to 1.0 gear ratio) and one with locked-elevator (1.0 to 1.0 gear ratio), were flutter tested in the Langley transonic dynamics tunnel with an empennage cantilever-mounted on a sting. The geared-elevator configuration fluttered experimentally at about 20% higher dynamic pressures than the locked-elevator configuration. The experimental flutter dynamic pressure boundaries for both configurations were nearly flat over a Mach number range from 0.9 to 1.1. Flutter calculations (mathematical models) were made for the geared-elevator configuration using three subsonic lifting-surface methods. In one method, the elevator was treated as a discrete surface, and in the other two methods, the stabilizer and elevator were treated as a single warped-surface with the primary difference between these two methods being in the mathematical implementation used. A comparison of the experimental and analytical results shows that the discrete-elevator method predicted best the experimental flutter dynamic pressure level. However, the single warped-surface methods predicts more closely the experimental flutter frequencies and Mach number trends.

Ruhlin, C. L.↗