Search NASA⌕ Search

SEARCH · Search NASA

Results for “Glass crystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Containerless Processing of a Lithium Disilicate Glass

Glasses of Li2O.2SiO2 (LS2) and LS2 doped with 0.001 wt% platinum (LS2 + 0.001 wt% Pt) compositions were melted, cooled and re-heated at controlled rates while levitated (containerless) inside an Electrostatic Levitator (ESL) furnace at NASA Marshall Space Flight Center. The experiments were conducted in vacuum using spherical 2.5 - 3.0 mm diameter glass samples. The measured critical cooling rate for glass formation, Rc, for the LS2 and LS2 + 0.001 wt% Pt glasses processed at ESL were 14 plus or minus 2 C/min and 130 plus or minus 5 C/min, respectively. The values of Rc for the same LS2 and LS2 + 0.001 wt% Pt glasses processed in a container were 62 plus or minus 3 C/min and 162 plus or minus 5 C/min, respectively. The effective activation energy for crystallization, E, for the LS2 glass processed without a container at ESL was higher than that for an identical glass processed in a container. These results suggest that the glass formation tendency for a containerless LS2 melt is significantly increased compared to an identical melt in contact with a container. The absence of heterogeneous nucleation sites that are inherently present in all melts held in containers is believed to be the reason for the increased glass forming tendency of this containerless melt.

Ranasinghe, K. S.↗
NASA NTRS1992

Lunar oxygen - The reduction of glass by hydrogen

The direct reduction of volcanic glass by hydrogen has been proposed as a method of extracting oxygen from the lunar soil. Experiments using lunar simulant glasses reacted with flowing hydrogen gas have demonstrated reduction at temperatures from 1000 to 1200 C. For melted samples ferrous iron was reduced to the metal, which formed large crystals at the expense of the glass. Samples held below the melting point rapidly devitrified, and iron was formed from submicrometer crystals of ilmenite and pyroxene. Weight losses of 3.6 - 4.5 percent, depending on glass composition, were achieved in 3 hours at 1100 C. A lunar oxygen plant operating at this efficiency and utilizing Apollo 17 orange glass as a feedstock could produce 50 kg of oxygen per ton of soil. The processes of reduction and sintering of lunar soil are synergistic, and could be combined to produce both oxygen and construction material at a moon base.

Allen, Carlton C.↗
NASA NTRS1982

An experimental study of the ice column habit transitions

The influence of supersaturation on column growth of ice crystals forming from atmospheric water vapor was investigated. A high density of crystals was generated on a glass fiber cooled by liquid N2 in a thermal diffusion chamber. Attention was focused on a neighbor-free hollow prism during a stepwise decrease in supersaturation while the crystal temperature was maintained constant. Another experiment involved epitaxial growth of ice crystals on CuS, where nonthickening crystals could only be grown below -7 C. A critical supersaturation was found to be necessary for growth of the basal plane. Beyound the critical value, surface kinetics do not control the growth rate, which is then dominated by the penetration of water molecules through the diffusion field surrounding the crystal.

Cho, N.↗
NASA NTRS2004

Containerless Processing of a Lithium Disilicate Glass

Glasses of Li2O.2SiO2 (LS2), and LS2 doped with 0.001wt% platinum (LS2 + 0.001 wt% Pt) compositions were melted, cooled and reheated at controlled rates while levitated (containerless) inside an Electrostatic Levitator (ESL) furnace at the NASA Marshall Space Flight Center, Huntsville, AL. The experiments were conducted in vacuum (approximately 10(exp -5) Pa) using spherical, 2.5 to 3 millimeter diameter, glass samples. The measured critical cooling rate for glass formation, R(sub c), for the LS2 and LS2+0.001 wt% Pt glasses processed at ESL were 14 plus or minus 2 Celsius per minute and 130 plus or minus 5 Celsius per minute, respectively. The values of R(sub c), for the same LS2 and LS2 + 0.001 wt% Pt glasses processed in a container were 62 plus or minus 3 Celsius per minute and 162 plus or minus 5 Celsius per minute, respectively. The effective activation energy for crystallization, E, for this LS2 glass processed without a container at ESL, 392 plus or minus 15 kiloJoules per mole, was higher than that, 270 plus or minus 15 kiloJoules per mole, for an identical glass processed in a container. These results suggest that the glass formation tendency for a containerless LS2 melt is significantly increased compared to an identical melt in contact with a container. The absence of heterogeneous nucleation sites that are inherently present in all melts held in containers, and or a change in the surface composition due to evaporation of Li2O during processing at ESL are likely reasons for the increased glass forming tendency of this containerless LS2 melt.

Ranasinghe, Kisa↗
NASA NTRS1993

The ilmenite liquidus and depths of segregation for high-Ti picrite glasses

Lunar picrite glasses represent primitive and perhaps near primary liquids which have suffered only minor degrees of crystallization or near crustal modification. These glasses are multisaturated with olivine and orthopyroxene at pressures from 20-25 kb. I argue below that high TiO2 mare glasses were indeed equilibrated with orthopyroxene and were segregated from the lunar mantle at mean depths of 400-500 km. The glasses are typically modelled as products of relatively low degrees of melting of an hybridized source resulting from the overturn and mixing of the gravitationally unstable cumulate pile. But the models are neither unique nor, in some cases, correct.

Hess, P. C.↗
NASA NTRS1992

Glass precursor approach to high-temperature superconductors

The available studies on the synthesis of high T sub c superconductors (HTS) via the glass precursor approach were reviewed. Melts of the Bi-Sr-Ca-Cu-O system as well as those doped with oxides of some other elements (Pb, Al, V, Te, Nb, etc.) could be quenched into glasses which, on further heat treatments under appropriate conditions, crystallized into the superconducting phase(s). The nature of the HTS phase(s) formed depends on the annealing temperature, time, atmosphere, and the cooling rate and also on the glass composition. Long term annealing was needed to obtain a large fraction of the 110 K phase. The high T sub c phase did not crystallize out directly from the glass matrix, but was preceded by the precipitation of other phases. The 110 K HTS was produced at high temperatures by reaction between the phases formed at lower temperatures resulting in multiphase material. The presence of a glass former such as B2O3 was necessary for the Y-Ba-Cu-O melt to form a glass on fast cooling. A discontinuous YBa2Cu3O(7-delta) HTS phase crystallized out on heat treatment of this glass. Attempts to prepare Tl-Ba-Ca-Cu-O system in the glassy state were not successful.

Bansal, Narottam P.↗
NASA NTRS1991

Optical Isolators With Transverse Magnets

New design for isolator includes zigzag, forward-and-backward-pass beam path and use of transverse rather than longitudinal magnetic field. Design choices produce isolator with as large an aperture as desired using low-Verdet-constant glass rather than more expensive crystals. Uses commercially available permanent magnets in Faraday rotator. More compact and less expensive. Designed to transmit rectangular beam. Square cross section of beam extended to rectangular shape by increasing one dimension of glass without having to increase magnetic field. Potentially useful in laser systems involving slab lasers and amplifiers. Has applications to study of very-high-power lasers for fusion research.

Fan, Yuan X.↗
NASA NTRS1999

Effects of Melt Processing on Evolution of Structure in PEEK

We report on the effects of melt processing temperature on structure formation in Poly(ether-ether-ketone), PEEK. Real time Small Angle X-ray Scattering, SAXS, and thermal analysis are used to follow the melting behavior after various stages of processing. Assignment of peaks to structural entities within the material, the relative perfection of the crystals, and the possibility of their reorganization, are all influenced by the melt processing history. With the advent of high intensity synchrotron sources of X-radiation, polymer scientists gain a research tool which, when used along with thermal analysis, provides additional structural information about the crystals during growth and subsequent melting. PEEK is an engineering thermoplastic polymer with a very high glass transition temperature (145 C) and crystal melting point (337 C). PEEK has been the subject of recent studies by X-ray scattering in which melt and cold crystallization were followed in real-time. X-ray scattering and thermal studies have been used to address the formation of dual endothermic response which has been variously ascribed to lamellar insertion, dual crystal populations, or melting followed by re-crystallization. Another important issue is whether all of the amorphous phase is located in interlamellar regions, or alternatively whether some is located in "pockets" away from the crystalline lamellar stacks. The interpretation of scattering from lamellar stacks varies depending upon whether such amorphous pockets are formed. Some groups believe all of the amorphous phase is interlamellar. This leads to selection of a smaller thickness for the crystals. Other groups suggest that most amorphous phase is not interlamellar, and this leads to the suggestion that the crystal thickness is larger than the amorphous layer within the stacks. To investigate these ideas, we used SAXS and Differential Scanning Calorimetry to compare results of single and dual stage melt crystallization of PEEK using a treatment scheme involving annealing/crystallization at T(sub a1) followed by annealing at T(sub a2) where either T(sub a1) < T(sub a2) or T(sub a1) > T(sub a2). We proposed a model to explain multiple melting endotherms in PPS, treated according to one or two-stage melt or cold crystallization. Key features of this model are that multiple endotherms: (1) are due to reorganization/recrystallization after cold crystallization; and, (2) are dominated by crystal morphology after melt crystallization at high T. In other words, multiple distinct crystal populations are formed by the latter treatment, leading to observation of multiple melting. PEEK 45OG pellets (ICI Americas) were the starting material for this study. Films were compression molded at 400 C, then quenched to ice water. Samples were heated to 375 C in a Mettler FP80 hot stage and held for three min. to erase crystal seeds before cooling them to T(sub a1) = 280 C . Samples were held at T(sub a2) for a period of time, then immediately heated to 360 C. In the second treatment samples were held at T(sub a1) = 31 C for different crystallization times t(sub c) then cooled to 295 C and held 15 min. In situ (SAXS) experiments were performed at the Brookhaven National Synchrotron Light Source with the sample located inside the Mettler hot stage. The system was equipped with a two-dimensional position sensitive detector. The sample to detector distance was 172.7 cm and the X-ray wavelength was 1.54 Angstroms. SAXS data were taken continuously during the isothermal periods and during the heating to 360 C at 5 C/min. Each SAXS scan was collected for 30 sec. Since the samples were isotropic, circular integration was used to increase the signal to noise ratio. After dual stage melt crystallization with T(sub a1) < T(sub a2) the lower melting endotherm arises from holding at T(sub a1). During cooling a broad distribution of crystals forms, and the low-melting tail is perfected during T(sub al). Heating to T(sub a2) melts these imperfect crystals and allows others with greater average long spacing to form in their place. After dual stage crystallization with T(sub a1) > T(sub a2), the amount of space remaining for additional growth at T(sub a2) depends upon the holding time at T(sub a1). The long period of crystals formed at T(sub a2) is smaller than that formed at T(sub a1) due to growth in a now-restricted geometry. Perfection of crystals is seen as an increase of the intensity of the population scattering at higher s, while the intensity of the population scattering at lower s stays constant. During heating from below to above the minor endotherm, we see rapid decrease of the intensity of the X-ray scattering corresponding to the population of crystals scattering in the shoulder. Another important observation is that after the sample is annealed at 295 C, the shoulder intensity is restored once again. The population scattering at higher s remains longer before it disappears in the sample treated to the second stage of melt crystallization, compared to the sample crystallized with a single stage. This could be interpreted as an effect of continued perfection of the less perfect population, which is also reflected in the increased melting temperature of the smaller endotherm as the holding time at 295 C increases. In the corresponding DSC scans we see a shift in the area and the peak temperature of the lower melting endotherm with an increase of the annealing time.

Georgiev, Georgi↗
NASA NTRS2015

Crystal-free Formation of Non-Oxide Optical Fiber

Researchers at NASA Marshall Space Flight Center have devised a method for the creation of crystal-free nonoxide optical fiber preforms. Non-oxide fiber optics are extensively used in infrared transmitting applications such as communication systems, chemical sensors, and laser fiber guides for cutting, welding and medical surgery. However, some of these glasses are very susceptible to crystallization. Even small crystals can lead to light scatter and a high attenuation coefficient, limiting their usefulness. NASA has developed a new method of non-oxide fiber formation that uses axial magnetic fields to suppress crystallization. The resulting non-oxide fibers are crystal free and have lower signal attenuation rates than silica based optical fibers.

Nabors, Sammy A.↗
NASA NTRS1979

Rates and processes of crystal growth in the system anorthite-albite

The growth rates and interface morphologies of crystals of synthetic compositions in the anorthite (CaAl2Si2O8)-albite (NaAlSi3O8) plagioclase feldspar system are measured in an investigation of the crystallization of igneous rocks. Mixed plagioclase glasses with compositions of 75% and 50% anorthite were observed using the microscope heating technique as they crystallized at temperatures near the liquidus, and 75%, 50% and 20% anorthite crystals were treated by resistance heating and observed at greater degrees of undercooling. Growth rates were found to be independent of time and to decrease with increasing albite content, ranging from 0.5 to 2 x 10 to the -5th cm/min. The crystal morphologies for all compositions are faceted near the liquidus and become progressively skeletal, dendritic and fibrillar with increasing undercooling.

Kirkpatrick, R. J.↗
NASA NTRS1991

Failure analysis of the lithium battery: A study of the header deposit on the cell top and diffusion within the electrode glass seal using nuclear microanalysis and FFTIR spectroscopy

The Solid Rocket Booster Range Safety System (SRBRSS) uses a lithium/poly-carbon monofluoride primary battery as a source of electrical power. After cell fabrication and activation, some battery cells have shown self discharge. One possible source of this cell discharge has been suggested to be the formation and growth of a conducting crystallized chemical compound across the glass bead insulator, electrically shorting the glass bead to the casing. This laboratory has begun an analysis of this compound, the glass seal holding the cathode into place, and the cell electrolyte, using Fast Fourier Transform Infrared (FFTIR) Analysis, Rutherford Backscattering Spectroscopy (RBS), and Nuclear Reaction Microanalysis. Preliminary measurements have confirmed the existence of lithium, nitrogen, fluorine, and oxygen on a reddish-brown deposit covering parts of the glass seal holding the positive electrode in place. Cells using Li metal electrodes, have many advantages over conventional primary batteries. One principal disadvantage of using Li batteries on a commercial basis would be the environmental impact of the fluorocarbon material. Another would be the relatively high expense of (CF)n.

Hassan, Razi A.↗
NASA NTRS1985

Glass formation and properties in the system calcia-gallia-germania

The critical cooling rate for glass formation, R sub c was measured for four compositions in the system calcia-gallia-germania. The activation energy, E, and frequency factor, nu, for the crystallization process were determined by reheating the glasses at varied constant heating rates and measuring the temperature of crystallization. Both E and nu increased, with increasing germania content of the glass, whereas R sub c decreased. The density, refractive index, and Abbe number were also measured; all decreased with increasing GeO2 content. These results are compared with those for calcia-gallia-silica glasses of comparable compositions.

Angel, P. W.↗
NASA NTRS1994

Assimilation by lunar mare basalts: Melting of crustal material and dissolution of anorthite

We discuss techniques for calculating the amount of crustal assimilation possible in lunar magma chambers and dikes based on thermal energy balances, kinetic rates, and simple fluid mechanical constraints. Assuming parent magmas of picritic compositions, we demonstrate the limits on the capacity of such magmas to melt and dissolve wall rock of anorthitic, troctolitic, noritic, and KREEP (quartz monzodiorite) compositions. Significant melting of the plagioclase-rich crustal lithologies requires turbulent convection in the assimilating magma and an efficient method of mixing in the relatively buoyant and viscous new melt. Even when this occurs, the major element chemistry of the picritic magmas will change by less than 1-2 wt %. Diffusion coefficients measured for Al2O3 from an iron-free basalt and an orange glass composition are 10(exp -12) sq m/s at 1340 C and 10(exp -11) sq m/s at 1390 C. These rates are too slow to allow dissolution of plagioclase to significantly affect magma compositions. Picritic magmas can melt significant quantities of KREEP, which suggests that their trace element chemistry may still be affected by assimilation processes; however, mixing viscous melts of KREEP composition with the fluid picritic magmas could be prohibitively difficult. We conclude that only a small part of the total major element chemical variation in the mare basalt and volcanic glass collection is due to assimilation/fractional crystallization processes near the lunar surface. Instead, most of the chemical variation in the lunar basalts and volcanic glasses must result from assimilation at deeper levels or from having distinct source regions in a heterogeneous lunar mantle.

Finnila, A. B.↗
NASA NTRS1994

Assimilation by Lunar Mare Basalts: Melting of Crustal Material and Dissolution of Anorthite

We discuss techniques for calculating the amount of crustal assimilation possible in lunar magma chambers and dikes based on thermal energy balances, kinetic rates, and simple fluid mechanical constraints. Assuming parent magmas of picritic compositions, we demonstrate the limits on the capacity of such magmas to melt and dissolve wall rock of anorthitic, troctolitic, noritic, and KREEP (quartz monzodiorite) compositions. Significant melting of the plagioclase-rich crustal lithologies requires turbulent convection in the assimilating magma and an efficient method of mixing in the relatively buoyant and viscous new melt. Even when this occurs, the major element chemistry of the picritic magmas will change by less than 1-2 wt %. Diffusion coefficients measured for Al2O3 from an iron-free basalt and an orange glass composition are 10(exp -12) m(exp 2) s(exp -1) at 1340 C and 10(exp -11) m(exp 2) s(exp -1) at 1390 C. These rates are too slow to allow dissolution of plagioclase to significantly affect magma compositions. Picritic magmas can melt significant quantities of KREEP, which suggests that their trace element chemistry may still be affected by assimilation processes; however, mixing viscous melts of KREEP composition with the fluid picritic magmas could be prohibitively difficult. We conclude that only a small part of the total major element chemical variation in the mare basalt and volcanic glass collection is due to assimilation/fractional crystallization processes near the lunar surface. Instead, most of the chemical variation in the lunar basalts and volcanic glasses must result from assimilation at deeper levels or from having distinct source regions in a heterogeneous lunar mantle.

Finnila, A. B.↗
NASA NTRS1973

Crystal growth in fused solvent systems

Research is reported on the growth of electronic ceramic single crystals from solution for the future growth of crystals in a microgravity environment. Work included growth from fused or glass solvents and aqueous solutions. Topics discussed include: crystal identification and selection; aqueous solution growth of triglycine sulphate (TGS); and characterization of TGS.

Ulrich, D. R.↗
NASA NTRS1979

Petrography and olivine mineral chemistry of chondrules and inclusions in the Allende meteorite

The examination of 19 polished-thin sections from a sample of the Allende meteorite reveals that anhedral olivine chondrules (OCs) are the most abundant chondrule type (19.7% of total chondrules + inclusions), followed by recrystallized OCs (7.5%), euhedral OCs (2.9%), glassy/skeletal OCs (2.7%), and barred OCs (2.3%). The most abundant inclusions are those comprised of many small olivine crystals with varying amounts of opaque minerals and glass (31.5%), followed by fine grained inclusions (16.1%) and single olivine crystals (15.7%). Microprobe analyses of olivines show that recrystallized and barred chondrules are the most forsteritic and exhibit relatively narrow compositional ranges, whereas single crystals have the widest range, from Fa sub 0.3 to Fa sub 49.

Simon, S. B.↗
NASA NTRS1977

High-silica glass inclusions in olivine of Luna-24 samples

Optical examination of nine polished grain mounts of Luna-24 drill-core material (0.09-0.50 mm size) revealed melt inclusions in olivine crystals. Two inclusions consist of clear glass with exceptionally high Si, yet contain no visible daughter minerals and have had no reaction effects with the olivine walls. Their compositions (one has SiO2 93.8, Al2O3 1.51, FeO 2.32, MgO 1.61, CaO 0.06, Na2O less than 0.05, K2O 0.11, total 99.41%; the other is similar) are unique and quite unlike the high-Si high-K melt of granitic composition that is found as inclusions in late-stage minerals of these (and the Apollo) samples, from silicate liquid immiscibility. The host olivines are Fo73 and Fo51. The origin of the melt in the inclusions and the lack of reaction effects are perplexing unsolved problems.

Roedder, E.↗