Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Microstructure evolution and properties of graphene nanoplatelets reinforced aluminum matrix composites

Highlights: • Lamellar structure of GNPs fibers and Al matrix was obtained in the rolling direction. • Stacking faults were observed in Al grains due to greatly increased GNPs/Al interfaces. • Strength of Al-0.2 wt% GNPs increased 36.8% with negligible electrical conductivity loss. - Abstract: Aluminum matrix composites reinforced with graphene nanoplatelets (GNPs) were prepared by continuous casting and subsequent rolling. Al-GNPs master alloy, prepared by ball milling and cold pressing, was added into Al melts to fabricate the composites. Microstructure evolution of the composites were observed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron back scattered diffraction (EBSD). GNPs distributed uniformly in the as-cast specimen and then transformed into fibers in the rolling direction after deformation and finally a lamellar structure formed in the composites. Raman spectra showed that the structural damage of GNPs mainly came from ball milling. The interface between GNPs and Al was well combined in general while a few microcracks were observed, which reduced the ductility of the composites and no adverse aluminum carbide (Al{sub 4}C{sub 3}) was detected at the interface. Stacking faults were observed interior of the aluminum grain, which may due to the existence of plentiful interface introduced by GNPs. Fracture observation revealed that the load transferred from Al matrix to GNPs. The ultimate tensile strength of Al-0.2 wt% GNPs composites was about 36.8% higher than that of pure Al with the same casting and rolling process, which should result from the lamellar structure and load transfer, while the conductivity of the composites decreased slightly, indicating that interface scattering between Al and GNPs is very limited. The investigation results show that Al-GNPs composite is potential for high strength and high conductivity application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of Temperature on the Texture Distribution in Two-Phase Region Hot Deformation of Grain-Oriented Silicon Steel

Hot deformation simulation test of 3% Si grain-oriented silicon (CGO) steel was carried out at different temperatures, and evolution of microstructures and recrystallized textures in two-phase region was analyzed by electron backscatter diffraction and optical microscopy. The “δ → γ” and “γ → α” phase transformation points of the two-phase region measured by differential scanning calorimetry method are 1272 and 819 °C, respectively, which are within the ranges of 1300-1350 and 800-850 °C, measured by water quenching. The hot deformation temperature has a large effect on the microstructure and texture in the steel. A higher hot deformation temperature leads to higher degree of recrystallization and larger average grain size, more γ-fiber textures and cube {100} <001> texture, but the rotated cube {100} <011> texture is stable. The recrystallized microstructure was also affected by the phase compositions. While the cube {100} <001> texture results in typical austenite recrystallization texture, {111} textures lead to typical ferrite rolling textures.

36 MATERIALS SCIENCE↗

Crack tip microplasticity mediated by microstructure gradients

Abstract Traditional fracture theories infer damage at cracks (local field) by surveying loading conditions away from cracks (far field). This approach has been successful in predicting ductile fracture, but it normally assumes isotropic and homogeneous materials. However, myriads of manufacturing procedures induce heterogeneous microstructural gradients that can affect the accuracy of traditional fracture models. This work presents a microstructure‐sensitive finite element approach to explore the shielding effects of grain size and crystallographic orientation gradients on crack tip microplasticity and blunting. A dislocation density‐based crystal plasticity model conveys texture evolution, grain size effects, and directional hardening by computing the constraint from dislocation structures. The results demonstrate that the microstructure can act as a buffer between the local and far fields that affects the crack tip microplasticity variability. For nominal opening loading, grain size and texture affect the local ductility and induce a non‐negligible multiaxial plastic deformation. Furthermore, driving forces based on measuring displacements away from the crack tip are less affected by the microstructure, which suggests that traditional experimental methods smear out important crack tip variability.

Castelluccio, Gustavo M.↗

Influence of strain on the formation of cold-rolling and grain growth textures of an equiatomic HfZrTiTaNb refractory high entropy alloy

Highlights: • Effect of strain on Texture formation is reported in HfZrTiTaNb for the first time. • Cold-rolled microstructure shows high density of deformation heterogeneities. • Weak texture compared to other BCC phases in HEAs • Imposed strain does not affect texture significantly unlike other BCC materials. - Abstract: The effect of cold-rolling strain on the evolution of deformation and grain growth textures in an equiatomic HfZrTiTaNb refractory high entropy alloy (RHEA) was investigated. For this purpose, the development of microstructure and texture was compared in 50% and 90% cold-rolled materials. The development of deformation microstructure was accompanied by the formation of extensive deformation heterogeneities. The 90% cold-rolled material showed ultrafine lamellar regions as well as regions severely fragmented by the fine scale deformation heterogeneities. The 50% cold-rolled material showed dominant ND-fiber (ND//), while the 90% cold-rolled material showed presence of both RD (RD//) and ND-fiber components. Profuse deformation heterogeneities presumably weakened the deformation texture considerably. The annealing texture of the 50% and 90% cold-rolled material showed stronger {111} component. Comparison of the annealing texture of the 50% and 90% cold-rolled materials with other BCC HEA phases indicated much weaker texture. The annealing texture of the RHEA was not significantly strengthened by increasing cold-rolling strain, presumably due to the high density of deformation heterogeneities in the cold-rolled microstructure. Thus, deformation heterogeneities significantly influenced the formation of cold-rolling and annealing textures of the equiatomic HfZrTiTaNb RHEA.

36 MATERIALS SCIENCE↗

Heterogeneous microstructural evolution during hydrodynamic penetration of a high-velocity copper microparticle impacting copper

Microparticle hydrodynamic penetration (HDP) may be associated with the erosion regime in cold spray processing and other high-velocity impact events. Here, in an experimental approach where we can individually launch particles and study the impact sites, we explore copper microparticles impacted on copper substrates at velocities above 900 m/s where HDP begins. We lift cross-sectional lamellae from the impact sites with a focused-ion beam for further microstructural characterization using electron backscatter diffraction and scanning transmission electron microscopy. Due to the gradients of strain, strain rate, and temperature associated with HDP, heterogeneous microstructures result. The structural evolution processes observed include deformation twinning and multiple dislocation-mediated grain recrystallization mechanisms—geometric dynamic recrystallization (gDRX), discontinuous DRX (dDRX), and meta DRX (mDRX). The higher strains at the interface lead to the most significant structural changes and complex mechanisms. In contrast, there is a gradient to more conventional dislocation plasticity away from the interface (on either the particle or substrate side). Here, these microstructural observations are consistent with the deformation map for copper and extend the observations of impact-induced recrystallization across new regimes of behavior.

Cold spray process↗

Predicting microstructurally sensitive fatigue‐crack path in WE43 magnesium using high‐fidelity numerical modeling and three‐dimensional experimental characterization

Abstract Microstructurally small fatigue‐crack growth in polycrystalline materials is highly three‐dimensional due to sensitivity to local microstructural features (e.g., grains). One requirement for modeling microstructurally sensitive crack propagation is establishing the criteria that govern crack evolution, including crack deflection. Here, a high‐fidelity finite‐element modeling framework is used to assess the performance and validity of various crack‐growth criteria, including slip‐based metrics (e.g., fatigue‐indicator parameters), as potential criteria for predicting three‐dimensional crack paths in polycrystalline materials. The modeling framework represents cracks as geometrically explicit discontinuities and involves voxel‐based remeshing, mesh‐gradation control, and a crystal‐plasticity constitutive model. The predictions are compared to experimental measurements of WE43 magnesium samples subject to fatigue loading, for which three‐dimensional grain structures and fatigue‐crack surfaces were measured post‐mortem using near‐field high‐energy x‐ray diffraction microscopy and x‐ray computed tomography. Findings from this work are expected to improve the predictive capabilities of simulations involving microstructurally small fatigue‐crack growth in polycrystalline materials.

Engineering↗

Microstructural design in low alloy steels

The evolution of microalloyed steels from plain carbon steels is examined with emphasis on grain size control by use of Nb, Ti and V additions and by the application of controlled rolling. The structural changes during controlled rolling are described as well as the influence of alloying elements on these changes, and on the final microstructure. The achievement of high strength and toughness is discussed including the role of inclusions.

Honeycombe, R. W. K.↗

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗

Role of microstructure on twin nucleation and growth in HCP titanium: A statistical study

In this study, a detailed statistical analysis is performed using Electron Back Scatter Diffraction (EBSD) to establish the effect of microstructure on twin nucleation and growth in deformed commercial purity hexagonal close packed (HCP) titanium. Rolled titanium samples are compressed along rolling, transverse and normal directions to establish statistical correlations for {10–12}, {11–21}, and {11–22} twins. A recently developed automated EBSD-twinning analysis software is employed for the statistical analysis. Finally, the analysis provides the following key findings: (I) grain size and strain dependence is different for twin nucleation and growth; (II) twinning statistics can be generalized for the HCP metals magnesium, zirconium and titanium; and (III) complex microstructure, where grain shape and size distribution is heterogeneous, requires multi-point statistical correlations.

36 MATERIALS SCIENCE↗

Defect Production and Microstructural Feature Impact for Radiation Damage in Additively Manufactured 316 Stainless Steel

This milestone presents multi-scale modeling research results for additively manufactured 316 stainless steel. A combination of phase field, cluster dynamics, molecular dynamics, and density functional theory with machine learning is used, allowing for predictions of radiation-driven microstructural evolution in additively manufactured 316 stainless steel over a range of temperatures, damage rates, neutron spectra, and microstructures, and supporting the development of combined ion and neutron irradiation for material qualification. Informed by ion irradiation and neutron irradiation results across the Advanced Materials and Manufacturing Technologies program, we investigate the unique aspects of radiation-driven microstructure evolution in additively manufactured 316 stainless steel. In particular, we focus on understanding the impact of carbon concentration (varying, for example, between the 316L and 316H standards) on void formation; radiation-induced segregation at dislocation cells and grain boundaries; and the evolution of dislocation loops and network dislocation populations. We find that the unique characteristics of the additively manufactured microstructures must be accounted for in understanding the evolution of dislocation populations under thermal and irradiation conditions, such as the variation in sink strengths arising due to the variation in dislocation density. We also find that the radiation-induced segregation of Cr and Ni to grain boundaries and cell walls differs due to the differences in their defect sink biases. We also find that increasing the Ni content can slow vacancy diffusion, which may provide a mechanism for the observed reduction in transient swelling rate for austenitic Fe-Cr-Ni alloys with increasing Ni content. In addition, ion irradiations have shown that increasing carbon content in 316 SS results in a larger population of smaller voids, suggesting reduced vacancy diffusion. Our results show that the carbon content of additively manufactured 316 SS has a significant impact on the migration rate of defect clusters. The presence of carbon atoms results in carbon-vacancy trapping, significantly reducing the diffusion rate of vacancies. Carbon atoms may also be trapped near the surface of a void, which may reduce void growth by trapping vacancies that diffuse toward the void.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In situ synchrotron study of electromigration induced grain rotations in Sn solder joints

In this paper we report an in situ study of the early stage of microstructure evolution induced by electromigration in a Pb-free β-Sn based solder joint by synchrotron polychromatic X-ray microdiffraction. With this technique, crystal orientation evolution is monitored at intragranular levels with high spatial and angular resolution. During the entire experiment, no crystal growth is detected, and rigid grain rotation is observed only in the two grains within the current crowding region, where high density and divergence of electric current occur. Theoretical calculation indicates that the trend of electrical resistance drop still holds under the present conditions in the grain with high electrical resistivity, while the other grain with low resistivity reorients to align its a-axis more parallel with the ones of its neighboring grains. A detailed study of dislocation densities and subgrain boundaries suggests that grain rotation in β-Sn, unlike grain rotation in high melting temperature metals which undergo displacive deformation, is accomplished via diffusional process mainly, due to the high homologous temperature.

36 MATERIALS SCIENCE↗

Microstructure evolution and dynamic recrystallization behavior of a powder metallurgy Ti-22Al-25Nb alloy during hot compression

The flow behavior of a powder metallurgy (P/M) Ti-22Al-25Nb alloy during hot compression tests has been investigated at a strain rate of 0.01 s{sup −1} and a temperature range of 980–1100 °C up to various true strains from 0.1 to 0.9. The effects of deformation temperature and strain on microstructure characterization and nucleation mechanisms of dynamic recrystallization (DRX) were assessed by means of Optical microscope (OM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM) techniques, respectively. The results indicated that the process of DRX was promoted by increasing deformation temperature and strain. By regression analysis, a power exponent relationship between peak stresses and sizes of stable DRX grains was developed. In addition, it is suggested that the discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX) controlled nucleation mechanisms for DRX grains operated simultaneously during the whole hot process, and which played the leading role varied with hot process parameters of temperature and strain. It was further demonstrated that the CDRX featured by progressive subgrain rotation was weakened by elevating deformation temperatures. - Highlights: •Flow behavior of a P/M Ti-22Al-25Nb is studied by hot compression tests. •Microstructure evolution of alloy is affected by deformation temperature and strain. •The relationship between peak stress and stable DRX grain size was developed. •The process of DRX was promoted by increasing deformation temperature and strain. •Nucleation mechanisms of DRX were identified by EBSD analysis and TEM observation.

36 MATERIALS SCIENCE↗

A duality-based coupling of Cosserat crystal plasticity and phase field theories for modeling grain refinement

High-rate deformation processes of metals entail intense grain refinement and special attention needs to be paid to capture the evolution of microstructure. In this article, a new formulation for coupling Cosserat crystal plasticity and phase field is developed. A common approach is to penalize kinematic incompatibility between lattice orientation and displacement-based elastic rotation. However, this can lead to significant solution sensitivity to the penalty parameter, resulting in low accuracy and convergence rates. To address these issues, a duality-based formulation is developed which directly imposes the rotational kinematic compatibility. A weak inf-sup-based skew-symmetric stress projection is introduced to suppress instabilities present in the dual formulation. An additional least squares stabilization is introduced to suppress the spurious lattice rotation with a suitable parameter range derived analytically and validated numerically. The required high-order continuity is attained by the reproducing kernel approximation. It is observed that equal order displacement-rotation-phase field approximations are stable, which allows efficient employment of the same set of shape functions for all independent variables. The proposed formulation is shown to yield superior accuracy and convergence with marginal parameter sensitivity compared to the penalty-based approach and successfully captures the dominant rotational recrystallization mechanism including block dislocation structures and grain boundary migration.

42 ENGINEERING↗

Microstructure evolution during binder jet additive manufacturing of H13 tool steel

H13 is one of the most used tool steels for both hot and cold work tooling applications. Binder jet additive manufacturing offers the potential to deposit complex tools at scale due to larger powder bed sizes and faster deposition rates. However, to date there is no published literature on the sintering of H13 to full densification. Here, we discuss the pressureless sintering of binder jet AM H13 steel to full densification via supersolidus liquid phase sintering (SLPS) while presenting appropriate process windows (1360 °C – 1380 °C) for densification without distortion. The process windows have been rationalized based on thermodynamic calculations of liquid volume fractions with temperature. We show that higher binder saturation results in higher carbon retention and subsequently early liquid formation that can initiate the sintering process at lower temperatures. We report abnormal grain growth during sintering and found that the solidification phase transformations play a critical role on microstructural evolution and must be considered to accurately model the kinetics of SLPS.

36 MATERIALS SCIENCE↗

Phase-field modeling of aging-induced microstructure evolution in pentaerythritol tetranitrate thin films and ramifications for shock initiation

Aging of energetic materials may change performance and affect their safety and reliability, but the relationship between microstructure changes induced by aging and consequent performance changes has not been fully established. This work presents results of phase-field method simulations used to model microstructure evolution of vapor-deposited pentaerythritol tetranitrate (PETN) thin films. Simulated aging is shown to induce grain coarsening and substantial changes of the configuration of porosity in the film: Specifically, we show that porosity tends to concentrate in large pores to a greater degree in aged films, a state that is arrived at by closure or consolidation of small pores. To evaluate the performance of the as-deposited and aged films, we perform two-dimensional hydrocode flyer-film impact simulations that incorporate the phase-field output microstructures directly, permitting us to connect features therein to changes in reactivity, a key metric of energy output for shock initiation. The results demonstrate that declining sensitivity obtained for the simulated aged films can be correlated with the loss of fine-structured pores relatively early in the aging process, while long-term microstructure evolution that gradually alters the shape of large, branching pores is less impactful. Finally, we discuss commonalities and discrepancies between our simulation results and high-throughput initiation experiments on shock initiation of aged PETN thin films.

36 MATERIALS SCIENCE↗

A generalizable machine learning-assisted fast Fourier transform algorithm to simulate the large strain phenomena in polycrystalline materials

Machine learning methods have shown initial promise in constitutive modeling for single crystals or homogenized polycrystals, delivering notable computational efficiency. However, existing machine learning-based constitutive models often lack generalizability, limiting their application across diverse boundary value problems. This study introduces a thermodynamics-informed artificial neural network model to accelerate rate-tangent crystal plasticity fast Fourier transform simulations for cross-scale deformation behaviors of polycrystals under complex loading. Our model integrates microstructural variability and local interactions effectively. To address local effects in each grain, we employ K-means clustering to group Gauss points within the microstructure into clusters assumed to be in similar mechanical states. This approach, based on self-clustering analysis, extends model scope from macroscopic stress response to the granular level, capturing mechanical responses and orientation evolution across grains. This reduces the number of nonlinear problems to solve, with cluster responses propagated throughout each group. The thermodynamics-based artificial neural network-extracted features are further processed using local material state clusters to account for history-dependent deformation and evolving microstructures. Additionally, representative volume element simulations with rate-tangent crystal plasticity fast Fourier transform provide reliable datasets for model training. The proposed model demonstrates high efficiency, accuracy, self-consistency, and enhanced generalizability in predicting strain–stress responses and orientation evolution at both individual grain and aggregate scales under complex loading conditions, such as biaxial tension and arbitrary loading scenarios.

36 MATERIALS SCIENCE↗

A calibrated Monte Carlo approach to quantify the impacts of misorientation and different driving forces on texture development

A calibrated Monte Carlo (cMC) approach, which quantifies grain boundary kinetics within a generic setting, is presented. The influence of misorientation is captured by adding a scaling coefficient in the spin flipping probability equation, while the contribution of different driving forces is weighted using a partition function. The calibration process relies on the established parametric links between Monte Carlo (MC) and sharp-interface models. The cMC algorithm quantifies microstructural evolution under complex thermomechanical environments and remedies some of the difficulties associated with conventional MC models. After validation, the cMC approach is applied to quantify the texture development of polycrystalline materials with influences of misorientation and inhomogeneous bulk energy across grain boundaries. The results are in good agreement with theory and experiments.

99 GENERAL AND MISCELLANEOUS↗

Microstructural evolution during dynamic deformation of cubic metals: copper

Shockwave shape can influence dynamic damage evolution. Features such as rise time, pulse duration, peak shock pressure, pull back, and release rate are influenced as wave shape changes. However, their individual influence on dynamic damage evolution is not well understood. Specifically, changing from a square to triangular or Taylor wave loading profile can alter the release kinetics from peak shock pressure and the volume of material sampled during release. This creates a spatial influence. In high purity metals, because damage is often linked to boundaries within the microstructure (grain or twin), changing the volume of material sampled during release, can have a drastic influence on dynamic damage evolution as the number of boundaries or defects sampled is altered. In this study, model-driven dynamic experiments have been conducted on eu with four different grain sizes to examine, for a given shockwave shape, how the spatial effect of boundary distribution influences dynamic damage evolution. Both two and three dimensional damage characterization techniques have been utilized. This study shows the critical influence of spatial effects, in this case boundary density, on dynamic damage evolution. As the boundary density decreases, the damage evolution transitions from nucleation controlled to growth controlled. It also shows that specific boundaries, those with high Schmid factor orientations on either side, maybe a necessary condition for void formation.

36 MATERIALS SCIENCE↗