Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite/Epoxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Effect of moisture on the fatigue behavior of graphite/epoxy composite laminates

The form of the moisture distribution in the specimen (gradient and flat profile) was considered to establish the influence of accelerated moisture conditioning on fatigue behavior. For the gradient specimens having an average moisture content of 1.4 percent, fatigue life was reduced by a factor of 8 at all stress levels investigated. Corresponding reduction in fatigue life for the flat moisture profile specimens at the same average moisture content was comparatively smaller, being about a factor of 5 from the value in dry specimens. X-ray radiographic analysis of damage accumulation in compression-compression fatigue revealed interlaminar cracking to be the dominant mode of failure responsible for the observed enhanced cyclic degradation of moisture-conditioned specimens. This finding was corroborated by the observed systematic reduction in interlaminar shear strength as a function of moisture content, which, in turn, increased the propensity for delamination under cyclic compressive loads. Residual strength measurements on cycled specimens indicated significant strength reductions at long lives, particularly in moisture conditioned specimens.

Ramani, S. V.↗
NASA NTRS1979

Thermal Expansion and Swelling of Cured Epoxy Resin Used in Graphite/Epoxy Composite

The thermal expansion and swelling of resin material as influenced by variations in temperature during moisture absorption is discussed. Comparison measurements using composites constructed of graphite fibers and each of two epoxy resin matrices are included. Polymer theory relative to these findings is discussed and modifications are proposed.

Adamson, M. J.↗
NASA NTRS1978

Graphite/epoxy orthogrid panel fabrication

The structural concept considered for a spacecraft body structure is a grid stiffened skin with a skin laminate configuration and the stiffener grid geometry selected to best suit the design requirements. The orthogrid panel developed weighs 0.55 lb/sq ft and resisted an ultimate in-plane shear load of 545 lbf/in. The basic concept of a grid stiffener composite panel is that a relatively thin skin is reinforced with a gridwork of stiffeners so that the overall panel can resist design loads without becoming structurally unstable or being overstressed. The main feature of the orthogrid panel design is that it provides the potential for low cost structural panels when advanced to the production phase. The most innovative part of the fabrication method is the foam/fiberglass stiffener web grid billet fabrication and machining to size.

Lager, J. R.↗
NASA NTRS1980

Fracture modes of high modulus graphite/epoxy angleplied laminates subjected to off-axis tensile loads

Angelplied laminates of high modulus graphite fiber/epoxy were studied in several ply configurations at various tensile loading angles to the zero ply direction in order to determine the effects of ply orientations on tensile properties, fracture modes, and fracture surface characteristics of the various plies. It was found that fracture modes in the plies of angleplied laminates can be characterized by scanning electron microscope observation. The characteristics for a given fracture mode are similar to those for the same fracture mode in unidirectional specimens. However, no simple load angle range can be associated with a given fracture mode.

Sinclair, J. H.↗
NASA NTRS1980

Fracture modes of high modulus graphite/epoxy angleplied laminates subjected to off-axis tensile loads

Angleplied laminates of high modulus graphite fiber/epoxy were examined in several ply configurations at various tensile loading angles to the zero ply direction to determine the effects of ply orientations on tensile properties, fracture modes, and fracture surface characteristics of the various plies. Experimental results consist of stress-strain data, selected plots, fracture stresses and strains, and scanning electron microscope (SEM) photographs of fracture surfaces. It was found that the stress-strain curves were linear to fracture, and that although fracture surface characteristics for a given fracture mode are similar to those for the same fracture mode in uniaxial specimens, no simple load angle range can be associated with a given fracture mode. It was also concluded that SEM results must be supplemented with ply stress calculations in order to identify ranges of fracture modes occurring as a function of ply orientation with respect to the load direction.

Sinclair, J. H.↗
NASA NTRS1980

Accelerated characterization of graphite/epoxy composites

A method to predict the long term compliance of unidirectional off-axis laminates from short term laboratory tests is presented. The method uses an orthotropic transformation equation and the time-stress-temperature superposition principle. Short term tests are used to construct master curves for two off-axis unidirectional laminates with fiber angles of 10 and 90 degrees. Analytical predictions of long term compliance for 30 and 60 degrees laminates are made. Comparisons with experimental data are also given.

Griffith, W. I.↗
NASA NTRS1981

Creep and creep rupture of laminated graphite/epoxy composites

An incremental numerical procedure based on lamination theory is developed to predict creep and creep rupture of general laminates. Existing unidirectional creep compliance and delayed failure data is used to develop analytical models for lamina response. The compliance model is based on a procedure proposed by Findley which incorporates the power law for creep into a nonlinear constitutive relationship. The matrix octahedral shear stress is assumed to control the stress interaction effect. A modified superposition principle is used to account for the varying stress level effect on the creep strain. The lamina failure model is based on a modification of the Tsai-Hill theory which includes the time dependent creep rupture strength. A linear cumulative damage law is used to monitor the remaining lifetime in each ply.

Dillard, D. A.↗
NASA NTRS1981

Investigation of the effect of resin material on impact damage to graphite/epoxy composites

The results of an experimental program are described which establishes the feasibility and guide lines for resin development. The objective was to identify the basic epoxy neat resin properties that improve low velocity impact resistance and toughness to graphite-epoxy laminates and at the same time maintain useful structural laminate mechanical properties. Materials tests from twenty-three toughened epoxy resin matrix systems are included.

Palmer, R. J.↗
NASA NTRS1980

Accelerated characterization of graphite/epoxy composites

A method to predict the long-term compliance of unidirectional off-axis laminates from short-term laboratory tests is presented. The method uses an orthotropic transformation equation and the time-stress-temperature superposition principle. Short-term tests are used to construct master curves for two off-axis unidirectional laminates with fiber angles of 10 deg and 90 deg. In addition, analytical predictions of long-term compliance for 30 deg and 60 deg laminates are made. Comparisons with experimental data are also given.

Griffith, W. I.↗
NASA NTRS1980

Development of repair procedures for graphite/epoxy structures on commercial transports

A program is currently being performed for NASA-Langley on development of composite repair procedures adapted to the requirements of commercial airlines. The first phase of the program included a survey of airline damage experience and airline maintenance and repair capabilities for composite structures. A survey was also conducted for available data on composite damage tolerance. The second phase of the program evaluated various depot and field level repairs ranging from precured bonded graphite flush patches to mechanically attached aluminum patches. Based on airline survey results, the emphasis was on field repairs. The results verified the effectiveness of field type repairs for lightly loaded composite structure.

Stone, R. H.↗
NASA NTRS1981

Compression testing of graphite/epoxy composite materials

Three methods for compression testing coupons of filament-reinforced polymer-matrix composite materials are evaluated, to identify the sensitivity of the test techniques to laminate, specimen, and test parameters. A 'wedge-grip' compression fixture, a face-supported compression fixture, and an end-loaded coupon fixture are described. Specimens of 12.5-, 25-, and 50-mm widths, 8-, 16-, and 24-ply thicknesses, and of various fiber orientations were used to test the 'wedge-grip' compression fixture and the face-supported fixture; the end-loaded coupon fixture was tested using 16-ply specimens. Compressive strain-stress, strength, and modulus data obtained with the fixtures and evaluations showing the effects of all the test parameters are presented. One of the conclusions asserts that the 'wedge-grip' compression fixture provides good stress-strain data to failure for unidirectional and quasi-isotropic laminates.

Clark, R. K.↗
NASA NTRS1981

Biaxial tests of flat graphite/epoxy laminates

The influence of biaxially applied loads on the strength of composite materials containing holes was analyzed. The analysis was performed through the development of a three dimensional, finite element computer program that is capable of evaluating fiber breakage, delamination, and matrix failure. Realistic failure criteria were established for each of the failure modes, and the influence of biaxial loading on damage accumulation under monotonically increasing loading was examined in detail. Both static and fatigue testing of specially designed biaxial specimens containing central holes were performed. Static tests were performed to obtain an understanding of the influence of biaxial loads on the fracture strength of composite materials and to provide correlation with the analytical predictions. The predicted distributions and types of damage are in reasonable agreement with the experimental results. A number of fatigue tests were performed to determine the influence of cyclic biaxial loads on the fatigue life and residual strength of several composite laminates.

Liebowitz, H.↗
NASA NTRS1981

Deformation and failure mechanisms of graphite/epoxy composites under static loading

The mechanisms of deformation and failure of graphite epoxy composites under static loading were clarified. The influence of moisture and temperature upon these mechanisms were also investigated. Because the longitudinal tensile properties are the most critical to the performance of the composite, these properties were investigated in detail. Both ultimate and elastic mechanical properties were investigated, but the study of mechanisms emphasized those leading to failure of the composite. The graphite epoxy composite selected for study was the system being used in several NASA sponsored flight test programs.

Clements, L. L.↗
NASA NTRS1980

Behavior of damaged graphite/epoxy laminates under compression loading

The influence of three different resin systems on the damage tolerance of graphite/polymer laminates was evaluated. Testing consisted of both static compression and cyclic compression evaluation of 10.2 by 15.2 by 0.5 cm (4 by 6 by 0.2 in) laminates with circular holes, simulated delaminations, and low velocity impact. Damage growth under steadily increasing compression and cyclic compression loading was monitored. Damage size and impact-induced failures for the three materials were compared. Of the three material systems evaluated, the one most tolerant to impact damage exhibited the least delamination within the cross section due to impact, the highest transverse tension strain to failure, and the largest crack opening force, as determined from double cantilever beam tests.

Byers, B. A.↗
NASA NTRS1982

Effects of 50,000 hours of thermal aging on graphite/epoxy and graphite/polyimide composites

Thermal effects on tensile strengths of advanced composite systems have been determined for exposure times of 100 to 50,000 hours (5.7 years). Exposures were conducted at both ambient and reduced pressures at two temperatures for each composite. At the completion of the various aging periods, specimens were removed from the specially constructed aging furnaces, visually examined, and tensile tested at elevated temperature. After tensile testing, many of the thermal aging specimens were examined using a scanning electron microscope. Results of these studies are presented, and the changes in properties and the degradation mechanisms during high-temperature aging are discussed and illustrated using metallographic techniques.

Kerr, J. R.↗
NASA NTRS1983

Fabrication of Graphite/Epoxy Column Elements

Dimensionally precise columns wound on vertical mandrels. Dry fiber wound on tapered aluminum mandrel and outer sleeve. Winding and injection done at elevated temperature to minimize thermal-expansion problems during curing of resin. Technique used in textile industry.

Bluck, R. M.↗