Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grid Stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

A Fine-Grid Model for the ASRM Aft Segment with Gimballed Nozzle

Results from computational fluid dynamic analyses for complex three-dimensional internal flows in the Advanced Solid Rocket Motor (ASRM) are presented. In particular, flow visualization and tabulated results from a fine-grid model consisting of 1.5 M grid points for the ASRM Aft Segment at the l9-second burn time with an 8-degree nozzle gimbal angle are shown. The results from this model will enable characterization of various aspects of the ASRM internal environment, and in particular will allow an assessment of the heat transfer and stresses exerted on the submerged nozzle, casing insulation, and nozzle case joint.

Reske, Edward J.↗
NASA NTRS2006

Forecasting of Storm-Surge Floods Using ADCIRC and Optimized DEMs

Increasing the accuracy of storm-surge flood forecasts is essential for improving preparedness for hurricanes and other severe storms and, in particular, for optimizing evacuation scenarios. An interactive database, developed by WorldWinds, Inc., contains atlases of storm-surge flood levels for the Louisiana/Mississippi gulf coast region. These atlases were developed to improve forecasting of flooding along the coastline and estuaries and in adjacent inland areas. Storm-surge heights depend on a complex interaction of several factors, including: storm size, central minimum pressure, forward speed of motion, bottom topography near the point of landfall, astronomical tides, and, most importantly, maximum wind speed. The information in the atlases was generated in over 100 computational simulations, partly by use of a parallel-processing version of the ADvanced CIRCulation (ADCIRC) model. ADCIRC is a nonlinear computational model of hydrodynamics, developed by the U.S. Army Corps of Engineers and the US Navy, as a family of two- and three-dimensional finite-element-based codes. It affords a capability for simulating tidal circulation and storm-surge propagation over very large computational domains, while simultaneously providing high-resolution output in areas of complex shoreline and bathymetry. The ADCIRC finite-element grid for this project covered the Gulf of Mexico and contiguous basins, extending into the deep Atlantic Ocean with progressively higher resolution approaching the study area. The advantage of using ADCIRC over other storm-surge models, such as SLOSH, is that input conditions can include all or part of wind stress, tides, wave stress, and river discharge, which serve to make the model output more accurate. To keep the computational load manageable, this work was conducted using only the wind stress, calculated by using historical data from Hurricane Camille, as the input condition for the model. Hurricane storm-surge simulations were performed on an eight-node Linux computer cluster. Each node contained dual 2-GHz processors, 2GB of memory, and a 40GB hard drive. The digital elevation model (DEM) for this region was specified using a combination of Navy data (over water), NOAA data (for the coastline), and optimized Interferometric Synthetic Aperture Radar data (over land). This high-resolution topographical data of the Mississippi coastal region provided the ADCIRC model with improved input with which to calculate improved storm-surge forecasts.

Valenti, Elizabeth↗
NASA NTRS1999

Assimilation of Satellite Altimeter Data With a Four Dimensional Model of the Japan Sea

A data assimilation is carried out to detect the variability of the Japan Sea circulation in the range from a few days to several years and from eddy to basin scale. The model applied in this study is the same 1/6 degree GFDL MOM1 as Kim and Yoon (1999) but is driven by ECMWF daily wind stress, heat and fresh water fluxes. The satellite altimeter data of TOPEX/POSEIDON, ERS-1 (phase C and G) and -2 are assimilated by an approximate Kalman filter (Fukumori and M.Rizzoli, 1995). The approximation is made by seeking an asymptotic steady error covariance matrix (Fukumori et al., 1993) and by introducing a coarser grid model for the innovation (data-model misfit). The coarse grid model is defined on 1/2 degree horizontal resolution and consists of the barotropic stream function, first baroclinic displacement and velocity amplitudes. The assimilated estimates explain about 6cm sea level variability of the data (approximately 12cm in the southern part), which is much larger than the previous reduced-gravity model and TOPEX/POSEIDON altimeter data assimilation (Hirose et al., 1999). The impacts of the T/P and ERS data on the filtered estimates are comparable. The result also shows high correlation to subsurface water temperatures measured by CTD. Many of the mesoscale eddies/disturbances travel east-northeastward with the advection speed of 1-3cm/s though most of them generated in the western region can not pass over the Oki Spur. The quasi-biennial variability found by Hirose and Ostrovskii (1999) did not show clear propagation pattern. The shallow Oki Spur may work as a "western boundary" to this signal. This is more plausible estimation than by the R-G model which has no bottom topography.

Hirose, Naoki↗
NASA NTRS1976

Application of a novel finite difference method to dynamic crack problems

A versatile finite difference method (HEMP and HEMP 3D computer programs) was developed originally for solving dynamic problems in continuum mechanics. It was extended to analyze the stress field around cracks in a solid with finite geometry subjected to dynamic loads and to simulate numerically the dynamic fracture phenomena with success. This method is an explicit finite difference method applied to the Lagrangian formulation of the equations of continuum mechanics in two and three space dimensions and time. The calculational grid moves with the material and in this way it gives a more detailed description of the physics of the problem than the Eulerian formulation.

Chen, Y. M.↗
NASA NTRS1980

Method for alleviating thermal stress damage in laminates

A method is provided for alleviating the stress damage in metallic matrix composites, such as laminated sheet or foil composites. Discontinuities are positively introduced into the interface between the layers so as to reduce the thermal stress produced by unequal expansion of the materials making up the composite. Although a number of discrete elements could be used to form one of the layers and thus carry out this purpose, the discontinuities are preferably produced by simply drilling holes in the metallic matrix layer or by forming grooves in a grid pattern in this layer.

Hoffman, C. A.↗
NASA NTRS1981

Numerical investigation of turbulent channel flow

Fully developed turbulent channel flow was simulated numerically at Reynolds number 13800, based on centerline velocity and channel halt width. The large-scale flow field was obtained by directly integrating the filtered, three dimensional, time dependent, Navier-Stokes equations. The small-scale field motions were simulated through an eddy viscosity model. The calculations were carried out on the ILLIAC IV computer with up to 516,096 grid points. The computed flow field was used to study the statistical properties of the flow as well as its time dependent features. The agreement of the computed mean velocity profile, turbulence statistics, and detailed flow structures with experimental data is good. The resolvable portion of the statistical correlations appearing in the Reynolds stress equations are calculated. Particular attention is given to the examination of the flow structure in the vicinity of the wall.

Moin, P.↗
NASA NTRS1981

Partially confined multiple jet mixing

Results of hot-wire measurements in an incompressible partially confined jet issuing from an array of rectangular nozzles, equally spaced with their small dimensions aligned are presented. The quantities measured include mean velocity and the Reynolds stress in the two central planes of the jet at stations covering up to 115 widths (small dimension of a nozzle) downstream of the nozzle exit. For downstream distances greater than 60 widths, the flowfield is observed to be nearly homogenous and the turbulence appears to be quite similar to that of a grid generated turbulence.

Krothapalli, A.↗
NASA NTRS1984

Multi-100kW: Planar low cost solar array development

Seven low cost multi-100 kW planar solar array modules were fabricated and tested. Two different designs were used, demonstrating advanced solar array construction practices. Both module types utilized second generation gridded back cells featuring high efficiency and IR transparency. A silicon dioxide AR coating optimized for transmission at gamma = 1.7 microns was applied to the back surface. Two interconnect types, a single sheet printed circuit and a roll type, with alternate approaches to increasing transparency and reducing cost were designed and fabricated. Hinge stress and electrical power optimization were also examined. Two point designs were studied. The first design used a coilage longeron mast and is autonomously deployable. The second design used a Stac Beam for high natural frequency response and required astronaut assistance and assembly on orbit. It was conclusively demonstrated that planar arrays are the most cost effective design for use on the space station or other high power applications.

Source record↗
NASA NTRS1987

Toward the large-eddy simulations of compressible turbulent flows

New subgrid-scale models for the large-eddy simulation of compressible turbulent flows are developed based on the Favre-filtered equations of motion for an ideal gas. A compressible generalization of the linear combination of the Smagorinsky model and scale-similarity model (in terms of Favre-filtered fields) is obtained for the subgrid-scale stress tensor. An analogous thermal linear combination model is also developed for the subgrid-scale heat flux vector. The three dimensionless constants associated with these subgrid-scale models are obtained by correlating with the results of direct numerical simulations of compressible isotropic turbulence performed on a 96 to the third power grid using Fourier collocation methods. Extensive comparisons between the direct and modeled subgrid-scale fields are provided in order to validate the models. Future applications of these compressible subgrid-scale models to the large-eddy simulation of supersonic aerodynamic flows are discussed briefly.

Erlebacher, G.↗
NASA NTRS1987

Thermal stress cycling of GaAs solar cells

Thermal stress cycling was performed on gallium arsenide solar cells to investigate their electrical, mechanical, and structural integrity. Cells were cycled under low Earth orbit (LEO) simulated temperature conditions in vacuum. Cell evaluations consisted of power output values, spectral response, optical microscopy and ion microprobe mass analysis, and depth profiles on both front surface inter-grid areas and metallization contact grid lines. Cells were examined for degradation after 500, 5,000, 10,000 and 15,245 thermal cycles. No indication of performance degradation was found for any vendor's cell lot.

Francis, Robert W.↗
NASA NTRS1993

Turbulent structure of a wingtip vortex in the near field

The turbulent rollup of a vortex generated by a rectangular wing has been investigated. Extensive mean and turbulence measurements of the flowfield on a wingtip and in the near field have been completed. Velocity fluctuation measurements show that the near-field core is not laminar. A large axial velocity excess was found to exist in the core of the vortex. A momentum balance in the near-field of the wingtip showed that the magnitude of the core Reynolds-stress gradient terms are the same order as the largest terms in the governing equations. Navier-Stokes computations of the identical configuration, including wind tunnel walls and using measured inflow and outflow boundary conditions, reproduced many of the features of the experiment. Inherent limitations of the Baldwin-Barth turbulence model combined with limited grid resolution caused the computed vortex core to be more diffuse than desired. The momentum balance also demonstrated that the level of numerically generated false diffusion in the vortex core is relatively high.

Zilliac, Gregory G.↗
NASA NTRS1999

Quantification of Processing Effects on Filament Wound Pressure Vessels

A computational simulation procedure is described which is designed specifically for the modeling and analysis of filament wound pressure vessels. Cylindrical vessels with spherical or elliptical end caps can be generated automatically. End caps other than spherical or elliptical may be modeled by varying circular sections along the x-axis according to the C C! end cap shape. The finite element model generated is composed of plate type quadrilateral shell elements on the entire vessel surface. This computational procedure can also be sued to generate grid, connectivity and material cards (bulk data) for component parts of a larger model. These bulk data are assigned to a user designated file for finite element structural/stress analysis of composite pressure vessels. The procedure accommodates filament would pressure vessels of all types of shells-of-revolution. It has provisions to readily evaluate initial stresses due to pretension in the winding filaments and residual stresses due to cure temperature.

Aiello, Robert A.↗
NASA NTRS2002

Quantification of Processing Effects on Filament Wound Pressure Vessels

A computational simulation procedure is described which is designed specifically for the modeling and analysis of filament wound pressure vessels. Cylindrical vessels with spherical or elliptical end caps can be generated automatically. End caps other than spherical or elliptical may be modeled by varying circular sections along the x-axis according to the end cap shape. The finite element model generated is composed of plate type quadrilateral shell elements on the entire vessel surface. This computational procedure can also be used to generate grid, connectivity and material cards (bulk data) for component parts of a larger model. These bulk data are assigned to a user designated file for finite element structural/stress analysis of composite pressure vessels. The procedure accommodates filament wound pressure vessels of all types of shells-of -revolution. It has provisions to readily evaluate initial stresses due to pretension in the winding filaments and residual stresses due to cure temperature.

Aiello, Robert A.↗
NASA NTRS2003

Defect, Kinetics and Heat Transfer of CDTE Bridgman Growth without Wall Contact

A detached growth mechanism has been proposed, which is similar to that proposed by Duffar et al. and used to study the current detached growth system. From numerical results, we can conclude that detached growth will more likely appear if the growth and wetting angles are large and meniscus is flat. Detached thickness is dependent on growth angle, wetting angle, and gap width and shape of the fins. The model can also explain why the detached growth will not happen for metals in which the growth angle is almost zero. Since the growth angle of CdZnTe cannot be changed, to promote detached growth, the number density of the fins should be low and the wetting angle should be high. Also, a much smaller gap width of the fins should be used in the ground experiment and the detached gap width is much smaller. The shape of the fins has minor influence on detached growth. An integrated numerical model for detached solidification has been developed combining a global heat transfer sub-model and a wall contact sub-model. The global heat transfer sub-model accounts for heat and mass transfer in the multiphase system, convection in the melt, macro-segregation, and interface dynamics. The location and dynamics of the solidification interface are accurately tracked by a multizone adaptive grid generation scheme. The wall contact sub-model accounts for the meniscus dynamics at the three-phase boundary. Simulations have been performed for crystal growth in a conventional ampoule and a designed ampoule to understand the benefits of detached solidification and its impacts on crystalline structural quality, e.g., stoichiometry, macro-segregation, and stress. From simulation results, both the Grashof and Marangoni numbers will have significant effects on the shape of growth front, Zn concentration distribution, and radial segregation. The integrated model can be used in designing apparatus and determining the optimal geometry for detached solidification in space and on the ground.

Larson, D. J., Jr.↗
NASA NTRS1981

A potential-flow/boundary-layer method for calculating subsonic and transonic airfoil flow with trailing-edge separation

The development of a potential-flow/boundary-layer method for calculating subsonic and transonic turbulent flow past airfoils with trailing-edge separation is reported. A moment-of-momentum integral boundary-layer method is used which employs the law-of-the-wall/law-of-the-wake velocity profile and a two-layer eddy-viscosity model and ignores the laminar sublayer. All integrals across the boundary layer are obtained in closed form. Separation is assumed to occur when the shearing-stress velocity vanishes. A closed-form solution is derived for separated-flow regions where the shearing stress is negligible. In the potential-flow method, the exact form of the airfoil boundary condition is used, but it is applied at the chord line rather than the airfoil surface. This allows the accurate computation of flow about airfoils at large angles of attack but permits the use of body-oriented Cartesian computational grids. The governing equation for the perturbation velocity potential contains several terms in addition to the classical small-disturbance terms.

Barnwell, R. W.↗
NASA NTRS2020

Reynolds-Averaged Navier-Stokes Computations of the NASA Juncture Flow Model Using FUN3D and OVERFLOW

Two Reynolds-averaged Navier-Stokes codes, FUN3D and OVERFLOW, are used to assess the capability of Spalart-Allmaras-based turbulence models to predict the flow over the NASA Juncture Flow model. Both free-air and in-tunnel simulations are performed. While the tunnel walls have some influence, it is found to be relatively minor in the juncture region of interest. Results from the two codes are found to be consistent with each other in attached flow regions, but results in the area of separation still show grid and code sensitivity, even on grids as large as 400 million unknowns. Nonetheless, it is possible to draw conclusions regarding the model capabilities. Without a quadratic constitutive relation, the linear model predicts a separation size that is too large. The inclusion of a nonlinear quadratic constitutive relation improves results significantly, but separation still occurs too far upstream. Prediction of turbulent normal stress differences play a key role in this flow. Although the nonlinear model makes better predictions in this regard, they could still be improved, particularly in the streamwise normal component near the wall.

C L Rumsey↗
NASA NTRS1999

On Taylor-Series Approximations of Residual Stress

Although subgrid-scale models of similarity type are insufficiently dissipative for practical applications to large-eddy simulation, in recently published a priori analyses, they perform remarkably well in the sense of correlating highly against exact residual stresses. Here, Taylor-series expansions of residual stress are exploited to explain the observed behavior and "success" of similarity models. Until very recently, little attention has been given to issues related to the convergence of such expansions. Here, we re-express the convergence criterion of Vasilyev [J. Comput. Phys., 146 (1998)] in terms of the transfer function and the wavenumber cutoff of the grid filter.

Pruett, C. David↗
NASA NTRS1999

Turbulence Model Comparisons for a High-Speed Aircraft

Four turbulence models are described and evaluated for transonic flows over the High-Speed Research/industry baseline configuration known as Reference H by using the thin-layer, upwind, Navier-Stokes solver known as CFL3D. The turbulence models studied are the equilibrium model of Baldwin-Lomax (B-L) with the Degani-Schiff (D-S) modifications, the one-equation Baldwin-Barth (B-B) model, the one-equation Spalart-Allmaras (S-A) model, and Menter's two-equation Shear Stress Transport (SST) model. The flow conditions, which correspond to tests performed in the National Transonic Facility (NTF) at Langley Research Center, are a Mach number of 0.90 and a Reynolds number of 30 x 10 (exp. 6) based on mean aerodynamic chord for angles of attack of 1 deg., 5 deg., and 10 deg. The effects of grid topology and the representation of the actual wind tunnel model geometry are also investigated. Computed forces and surface pressures compare reasonably well with the experimental data for all four turbulence models.

Rivers, Melissa B.↗