An exploratory study of the roll behavior of ablating cones
Cone roll dynamics-ablation patterns coupling in hypersonic wind tunnels
Mcdevitt, J. B.↗
SEARCH · Search NASA
Results for “HYPERSONIC WIND TUNNEL”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Static and dynamic pitching moment measurements on a family of elliptic cones at Mach number 11 in helium
Static and dynamic pitching moment measurements were made on a family of constant volume elliptic cones about two fixed axes of oscillation in the NAE helium hypersonic wind tunnel at a Mach number of 11 and at Reynolds numbers based on model length of up to 14 million. Viscous effects on the stability derivatives were investigated by varying the Reynolds number for certain models by a factor as large as 10. The models investigated comprised a 7.75 deg circular cone, elliptic cones of axis ratios 3 and 6, and an elliptic cone with conical protuberances.
Orlik-Rueckermann, K. J.↗
Nonuniform flow field generation for supersonic compressor stator development: Design and preliminary results
Design and preliminary results are given for a technique which can generate a nonuniform flow similar to the discharge of an impulse supersonic compressor rotor. The technique utilizes a carefully contoured, two-dimensional blunt body in a conventional hypersonic wind tunnel to generate the required flow field. To show the effects of the flow vorticity, a cascade of impulse-type blades was tested in this test stream. Some preliminary performance data are given along with comparison with previously determined uniform flow results.
Lipfert, F. W.↗
Effect of thermally expanding surfaces on aerodynamic roll torques for cones.
An experimental and analytical study has been made of the aerodynamic roll torque on smoothly ablating, spinning cones. The tests, conducted in the Ames 3.5-Foot Hypersonic Wind Tunnel, indicated that the smoothly ablating model rolling at 0 deg angle of attack experiences roll damping, but when rolling at angle of attack an aerodynamic torque in the direction of spin arises if thermal expansion of the body surface occurs. An analysis of the spinning body at angle of attack is included to show how the relative importance of the ablator thermal expansion and the surface recession rate determines whether the motion is damped or undamped.
Mcdevitt, J. B.↗
Measurements of Reynolds analogy for a hypersonic turbulent boundary layer on a nonadiabatic flat plate.
The purpose of the described experiment was to obtain simultaneous measurements of skin friction and heat transfer at hypersonic Mach numbers, especially with conditions of considerable heat transfer. The experiment was conducted in air in the Ames Hypersonic Wind Tunnel, in which cold air was passed through an alumina storage heater system and heated to total temperatures ranging from about 670 to 1170 K. The nozzle was contoured to produce a flow at Mach 7.4. Thin-skin heat-transfer gauges were placed at equal intervals along the centerline of a sharp-edge flat plate, which was used as the model. A skin-friction balance and a boundary-layer pitot-pressure rake were mounted on each side of the centerline at a certain distance from the leading edge.
Keener, E. R.↗
The effect of angle of attack on boundary-layer transition on cones.
Boundary-layer transition on 5- and 15-deg half-angle cones was studied as a function of angle of attack (ranging from 0 to 20 deg) in a 3.5 ft hypersonic wind tunnel at a freestream Mach number of 7.4. It is shown that the influence of the angle of attack on the transition Reynolds number is a function of the meridian angle. On the windward ray of the 15-deg cone, transition Reynolds numbers show an initial slight increase and then a decrease with increasing angle of attack; leeward-ray Reynolds numbers for this cone decrease rapidly with angle of attack. Windward-ray transition Reynolds numbers increase monotonically with angle of attack on the 5-deg cone, but the effect of the angle of attack on the leeward ray is the same as for the 15-deg cone.
Mateer, G. G.↗
Investigation of flow fields within large scale hypersonic inlet models
Analytical and experimental investigations were conducted to determine the internal flow characteristics in model passages representative of hypersonic inlets for use at Mach numbers to about 12. The passages were large enough to permit measurements to be made in both the core flow and boundary layers. The analytical techniques for designing the internal contours and predicting the internal flow-field development accounted for coupling between the boundary layers and inviscid flow fields by means of a displacement-thickness correction. Three large-scale inlet models, each having a different internal compression ratio, were designed to provide high internal performance with an approximately uniform static-pressure distribution at the throat station. The models were tested in the Ames 3.5-Foot Hypersonic Wind Tunnel at a nominal free-stream Mach number of 7.4 and a unit free-stream Reynolds number of 8.86 X one million per meter.
Gnos, A. V.↗
Hypersonic flows in large-scale inlet models.
Analytical and experimental investigations were conducted to determine the characteristics of the internal flows in model passages representative of inlets for a typical Mach 12 hypersonic cruise vehicle and also sufficiently large for reliable data to be obtained. Three large-scale inlet models, each having a different internal compression ratio, were designed to provide maximum performance at the throat stations. Tests were conducted in the Mach 7.4 nozzle of the NASA Ames 3.5-foot hypersonic wind tunnel at a nominal test Reynolds number of 2,700,000 per ft. The experimental results revealed that a high level of total pressure recovery, approximately 0.85 (relative to the inlet-entrance conditions) for the core flow of the internal passage, was achieved for each inlet design.
Seebaugh, W. R.↗
A theoretical and experimental investigation of cylindrical electrostatic probes at arbitrary incidence in flowing plasma
The theory for calculating the current collected by a negatively biased cylindrical electrostatic probe at an arbitrary angle of attack in a weakley ionized flowing plasma is presented. The theory was constructed by considering both random and directed motion simultaneous with dynamic coupling of the flow properties and of the electric field of the probe. This direct approach yielded a theory that is more general than static plasma theories modified to account for flow. Theoretical calculations are compared with experimental electrostatic probe data obtained in the free stream of an arc-heated hypersonic wind tunnel. The theoretical calculations are based on flow conditions and plasma electron densities measured by an independent microwave interferometer technique. In addition, the theory is compared with laboratory and satellite data previously published by other investigators. In each case the comparison gives good agreement.
Jenkins, R. V.↗
Measurement and correlation of aerodynamic heating to surface corrugation stiffened structures in thick turbulent boundary layers
The flow conditions for which heating distributions were measured on corrugated surfaces and wavy walls in turbulent boundary layers are shown, along with the ratio of the displacement thickness to the roughness height versus the local edge Mach number for an equivalent smooth surface. The present data are seen to greatly extend the range of data available on corrugated surfaces in turbulent boundary layers. These data were obtained by testing fullscale corrugation roughened panels in the wall boundary layer of a supersonic and hypersonic wind tunnel. The experimental program used to obtain the data is described. The data are analyzed and correlated in terms of the pertinent flow and geometric parameters. The developed correlations are compared with the available thin boundary layer data, as well as with previously published correlation techniques.
Brandon, H. J.↗
Heat transfer tests of an 0.006-scale thin-skin space shuttle model (41-OTS) in the Ames 3.5-foot HWT at M equals 5.3 (IH15)
Data obtained from heat transfer tests of an 0.006-scale space shuttle vehicle in a 3.5-foot hypersonic wind tunnel are presented. The purpose of these tests was to parametrically investigate the ascent heating of the integrated vehicle. Configurations tested were complete for integrated vehicle, orbiter alone, external tank alone, and SRB alone. All configurations were tested with and without transition grit. Testing was conducted at a Mach number of 5.3, and at Reynolds numbers of 2 and 5 million per foot. The angle of attack range varied from 0 to minus 5 degress, execpt for SRB alone, which was tested from minus 5 to 90 degrees. Heat transfer data were obtained from 223 iron-constantan thermocouples attached to thin-skin stainless steel inserts.
Walstad, D. G.↗
Sonic boom pressure signatures for the space shuttle launch vehicle
Sonic boom pressure signatures were measured in supersonic and hypersonic wind tunnels for models of the space shuttle launch vehicle at 0 deg angle of attack with and without solid body simulations of the exhaust plumes. Data were measured at 30 deg increments in roll angle from 90 deg to 180 deg at Mach numbers from 3.02 to 5.56.
Mendoza, J. P.↗
Developments in convective heat transfer models featuring seamless and selected detail surfaces, employing electroless plating
Several model/instrument concepts employing electroless metallic skin were considered for improvement of surface condition, accuracy, and cost of contoured-geometry convective heat transfer models. A plated semi-infinite slab approach was chosen for development and evaluation in a hypersonic wind tunnel. The plated slab model consists of an epoxy casting containing fine constantan wires accurately placed at specified surface locations. An electroless alloy was deposited on the plastic surface that provides a hard, uniformly thick, seamless skin. The chosen alloy forms a high-output thermocouple junction with each exposed constantan wire, providing means of determining heat transfer during tunnel testing of the model. A selective electroless plating procedure was used to deposit scaled heatshield tiles on the lower surface of a 0.0175-scale shuttle orbiter model. Twenty-five percent of the tiles were randomly selected and plated to a height of 0.001-inch. The purpose was to assess the heating effects of surface roughness simulating misalignment of tiles that may occur during manufacture of the spacecraft.
Stalmach, C. J., Jr.↗
Results of convective heating tests of a longitudinal gap on the Rockwell flat plate model (15-0, insert 7) in the NASA/Ames Research Center
Results are presented which were obtained from tests in a hypersonic wind tunnel to determine aerodynamic heating rates in a gap running parallel or slightly askew to the flow direction. The model used was a flat plate instrumented in thin-skin sections with chromelconstantan thermocouples. Heating rate profiles lengthwise along and down into the gap were obtained, and additional data were obtained from a total temperature probe and rake fabricated during the test to investigate an apparent aerodynamic cooling trend in the gap. Model variables were width, depth, length, and orientation of the gap relative to the flow direction. The tests were conducted at Mach 5.1 and Reynolds numbers per foot of 500,000, 1,000,000, and 2,000,000.
Quan, M.↗
All-nickel hot-wire probe
Device operates in supersonic and hypersonic wind tunnels at temperatures of 700 to 760 C.
Lemos, F. R.↗
Real gas scale effects on hypersonic laminar boundary-layer parameters including effects of entropy-layer swallowing
Inviscid and viscous (laminar boundary-layer) flow-field calculations under perfect gas hypersonic wind tunnel and equilibrium real gas flight conditions are presented for the windward centerline of the Rockwell International 139 Space Shuttle Orbiter at a 30-deg angle of attack. Correlation parameters for laminar boundary-layer edge quantities and surface heat transfer are developed which properly account for entropy-layer-swallowing effects under both real and perfect gas conditions. Some implications of the proposed correlation parameters on boundary-layer transition are discussed.
Adams, J. C., Jr.↗
Hypersonic heat-transfer and transition correlations for a roughened shuttle orbiter
The effect of roughness on the heat transfer distributions and the transition criteria for the windward pitch plane of the shuttle orbiter at an angle of attack of 30 deg was studied using data obtained in hypersonic wind tunnels. The heat transfer distributions and the transition locations for the roughened models were compared with the corresponding data for smooth models. The data were correlated using theoretical solutions for a nonsimilar, laminar boundary layer subject to two different flow field models for the orbiter.
Bertin, J. J.↗
Analysis of heat transfer in a simulated wing-elevon cove in hypersonic flow
A simplified analytical model of leakage into a wing-elevon cove under high speed external flow conditions is presented. The model accounts for convection from the high temperature gas stream leaking into the cove, radiation exchanges between walls and with the environment, and axial conduction within the channel walls. Comparisons are made of predicted and measured wall temperatures of an experimental wing-elevon-cove model that was tested in a hypersonic wind tunnel. Analytically determined Nusselt numbers for laminar flow entrance conditions are compared with those calculated from experimentally measured gas temperatures, wall temperatures and wall heating rates. Although reasonable agreement appears to be indicated, testing times much larger than those of the present test program (5 seconds) would be desirable in evaluating the reliability and accuracy of the simplified model.
Keshock, E. G.↗