Search NASA⌕ Search

SEARCH · Search NASA

Results for “High dimensional data,”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Injectant mole fraction measurements of transverse injection in constant area supersonic ducts

Planar measurements of the injectant mole fraction distribution in a nonreacting model SCRAMJET combustor have been made using a nonintrusive optical technique, laser-induced iodine fluorescence. The combustor geometry investigated in this work was staged, transverse sonic injection of air into Mach 2 and Mach 2.9 freestreams. Accurate three-dimensional surveys of the injectant mole fraction distribution for both freestream Mach numbers have been generated. These experimental measurements provide valuable insight into the fluid mechanics of the mixing process. The existence of streamwise vortices is shown to dominate the mixing in the injector nearfield while shock wave interactions with the injectant plume are seen to significantly enhance mixing downstream of the injectors. The effect of combustor Mach number on injectant mixing is found to be small for this geometry. These measurements provide an accurate data set for the validation of computational fluid dynamics codes being developed for the calculation of highly three-dimensional nonreacting supersonic combustor flow fields.

Hollo, Steven D.↗
NASA NTRS1981

Langley high-lift research on a high-aspect-ratio supercritical wing configuration

To determine the low speed performance characteristics of a representative high aspect ratio supercritical wing, two low speed jet transport models were fabricated. A 12-ft. span model was used for low Reynolds number tests in the Langley 4- by 7-Meter Tunnel and the second, a 7.5-ft. span model, was used for high Reynolds number tests in the Ames 12-foot Pressure Tunnel. A brief summary of the results of the tests of these two models is presented and comparisons are made between the data obtained on these two models and other similar models. Follow-on two and three dimensional research efforts related to the EET high-lift configurations are also presented and discussed.

Morgan, H. L., Jr.↗
NASA NTRS1979

Synthesis of regional crust and upper-mantle structure from seismic and gravity data

Available seismic and ground based gravity data are combined to infer the three dimensional crust and upper mantle structure in selected regions. This synthesis and interpretation proceeds from large-scale average models suitable for early comparison with high-altitude satellite potential field data to more detailed delineation of structural boundaries and other variations that may be significant in natural resource assessment. Seismic and ground based gravity data are the primary focal point, but other relevant information (e.g. magnetic field, heat flow, Landsat imagery, geodetic leveling, and natural resources maps) is used to constrain the structure inferred and to assist in defining structural domains and boundaries. The seismic data consists of regional refraction lines, limited reflection coverage, surface wave dispersion, teleseismic P and S wave delay times, anelastic absorption, and regional seismicity patterns. The gravity data base consists of available point gravity determinations for the areas considered.

Alexander, S. S.↗
NASA NTRS1992

Turbulence measurements of high shear flow fields in a turbomachine seal configuration

The mean velocity and Reynolds stress tensor throughout a whirling annular seal are presented. The data was collected with a three dimensional laser Doppler velocimeter using phase averaging. Two axial flow conditions (Re = 12,000 and 24,000) were studied at one shaft speed (Ta = 6,600). The eccentricity and whirl ratios were 50 and 100 percent, respectively. There is a region of high axial momentum in this region is higher in the low Reynolds number case due to an axial recirculation zone that occurs on the suction side of the rotor at the inlet. The recirculation zone does not occur in the high Reynolds number case. At both Reynolds numbers, there is a recirculation zone on the rotor surface in the pressure side of the inlet. This recirculation zone extends from 20 to 200 degrees rotor zenith in the tangential direction, and is one third of a clearance wide radially. The high Reynolds number recirculation zone is 1.5 mean clearances long, while the low Reynolds number zone extends 2 mean clearances downstream. When compared to previous studies, it is apparent that the tangential momentum is no greater for a seal with whirl than for one without if other parameters are constant. Areas of high tangential momentum occur in the clearance where the axial momentum is low. Average exit plane tangential velocities in the high Reynolds number case are 1.5 times greater than those in the other flow case. These results are in general agreement with predictions made by other investigators.

Morrison, Gerald L.↗
NASA NTRS1987

Application of Advanced Very High Resolution Radiometer vegetation index to study atmosphere-biosphere exchange of CO2

Normalized difference vegetation indices derived from radiances measured by the Advanced Very High Resolution Radiometer were used to prescribe the phasing of terrestrial photosynthesis. The satellite data were combined with field data on soil respiration and a global map of net primary productivity to obtain the seasonal exchange of CO2 between the atmosphere and the terrestrial biosphere. The monthly fluxes of CO2 thus obtained were employed as source/sink functions in a global three-dimensional atmospheric tracer transport model to simulate the annual oscillations of CO2 in the atmosphere. The results demonstrate that satellite data of high spatial and temporal resolution can be used to provide quantitative information about seasonal and longer-term variations of photosynthetic activity on a global scale.

Fung, I. Y.↗
NASA NTRS1990

Model of the high-latitude ionospheric convection pattern during southward interplanetary magnetic field using DE 2 data

Data from the polar-orbiting satellite DE 2 are used to calculate one-dimensional electrostatic potential distributions across the polar cap region. Using passes that lie within + or - 3 hours MLT of the dawn-dusk line, various parameters of the polar potential distribution (location and magnitude of the maxima and minima, location of the zero potential point, etc.) are analyzed in relation to each other and to the IMF. The resulting dependences are used to derive a two-dimensional model of the distribution of the electrostatic potential in the high-latitude ionosphere during times of southward IMF. This model can be generated using as inputs either the ionospheric potential parameters or, based on the relationships analyzed here, the IMF conditions. The capabilities of the resulting mathematical model are illustrated, and the importance of retaining a flexibility in the model to accommodate individual observations is emphasized.

Hairston, M. R.↗
NASA NTRS1980

Greenhouse models of Venus' high surface temperature, as constrained by Pioneer Venus measurements

Recent measurements conducted from the Pioneer Venus probes and orbiter have provided a significantly improved definition of the solar net flux profile, the gaseous composition, temperature structure, and cloud properties of Venus' lower atmosphere. Using these data, we have carried out a series of one-dimensional radiative-convective equilibrium calculations to determine the viability of the greenhouse model of Venus' high surface temperature and to assess the chief contributors to the greenhouse effect. New sources of infrared opacity include the permitted transitions of SO2, CO, and HCl as well as opacity due to several pressure-induced transitions of CO2. We find that the observed surface temperature and lapse rate structure of the lower atmosphere can be reproduced quite closely with a greenhouse model that contains the water vapor abundance reported by the Venera spectrophotometer experiment. Thus the greenhouse effect can account for essentially all of Venus' high surface temperature. The prime sources of infrared opacity are, in order of importance, CO2, H2O, cloud particles, and SO2, with CO and HCl playing very minor roles.

Pollack, J. B.↗
NASA NTRS1973

Application of phase-change technique to thin sections with heating on both surfaces

A numerical digital computer program was developed to calculate the heat-transfer coefficients for both sides of a one-dimensional finite slab subject to the boundary conditions ascribed to the phase-change coating heat-transfer technique. In a typical tunnel test situation where a thin wing was exposed to heating on both sides, the data reduction procedures for a semi-infinite slab gave heat-transfer coefficients as much as 375 percent too high on the side with the lowest heating. The results from the one-dimensional finite-slab procedure are presented in the form of correction factors to the solution for a semi-infinite slab in terms of parameters normally used with the phase-change heat-transfer technique. These correlations are not restricted to slab thickness or thermophysical properties and are easily used to obtain accurate data on thin model sections.

Hunt, J. L.↗
NASA NTRSDate not supplied

HLPW-4/GMGW-3: Overview and Workshop Summary

The Fourth AIAA CFD High Lift Prediction Workshop and the Third Geometry and Mesh Generation Workshop were held collaboratively with the common goal of assessing the numerical prediction capability of current-generation computational fluid dynamics (CFD) technology for swept, medium/high-aspect-ratio wings in high-lift configurations. A key aspect of this joint endeavor was the use of Technology Focus Groups, an innovative new approach for workshops involving close collaboration between participants. These groups, which included both mesh generation and flow solver experts, worked to accelerate advancements for their particular methodologies by addressing key questions of importance {\em prior} to the workshop. The high-lift version of the NASA Common Research Model (CRM-HL) configuration was the focus of this workshop. Measured experimental wind tunnel data were available for comparison. The workshop also included a two-dimensional turbulence model verification exercise based on the CRM-HL wing shape. Altogether, 44 participants submitted a total of 184 data sets of CFD results. This paper provides a high-level summary of the results and conclusions from the workshop. Like at past workshops, fixed-grid Reynolds-averaged Navier-Stokes continued to be inaccurate and inconsistent for high lift. However, mesh adaptation definitively brought more consistency. Scale-resolving methods appeared most promising for predicting high-lift flow physics.

Christopher L Rumsey↗
NASA NTRS1979

Fuel spray data with LDV

Droplet size and two component velocities in the severe environment of an operating gas turbine combustor system can be measured simultaneously using the solar laser morphokinetomer (SLM) which incorporates the following capabilities: (1) measurement of a true two-dimensional velocity vector with a range of + or - (0.01-200 m/sec); (2) measurement of particle size (range 5 to 300 micron m) simultaneously with the measurement of velocity; (3) specification of probe volume position coordinates with a high degree of accuracy (+ or - 0.5 mm); (4) immediate on-line data checks; and (5) rapid computer storage of acquired data. The optical system of the SLM incorporates an ultrasonic beam splitter to allow the measurement of a two-dimensional velocity vector simultaneously with particle size. A microprocessor with a limited storage capability permits immediate analysis of test data in the test cell.

Rohy, D. A.↗
NASA NTRS1989

Quantitative characterization of a nonreacting, supersonic combustor flowfield using unified, laser-induced iodine fluorescence

A calibrated, nonintrusive optical technique, laser-induced iodine fluorescence (LIIF) was used to quantify the steady, compressible flowfield of a nonreacting, supersonic combustor. The combustor was configured with single and staged, transverse-air injection into a supersonic-air freestream behind a rearward-facing step. Pressure, temperature, two-velocity components, and injectant mole fraction were measured with high spatial resolution in the three-dimensional flowfields. These experimental results provide a benchmark set of data for validation of computational fluid dynamic (CFD) codes being developed to model supersonic combustor flowfields.

Fletcher, D. G.↗
NASA NTRS1990

Experimental investigation of a supersonic swept ramp injector using laser-induced iodine fluorescence

Planar measurements of injectant mole fraction and temperature have been conducted in a nonreacting supersonic combustor configured with underexpanded injection in the base of a swept ramp. The temperature measurements were conducted with a Mach 2 test section inlet in streamwise planes perpendicular to the test section wall on which the ramp was mounted. Injection concentration measurements, conducted in cross flow planes with both Mach 2 and Mach 2.9 free stream conditions, dramatically illustrate the domination of the mixing process by streamwise vorticity generated by the ramp. These measurements, conducted using a nonintrusive optical technique (laser-induced iodine fluorescence), provide an accurate and extensive experimental data base for the validation of computation fluid dynamic codes for the calculation of highly three-dimensional supersonic combustor flow fields.

Hartfield, Roy J.↗
NASA NTRS2000

Navier-Stokes Analysis of a High Wing Transport High-Lift Configuration with Externally Blown Flaps

Insights and lessons learned from the aerodynamic analysis of the High Wing Transport (HWT) high-lift configuration are presented. Three-dimensional Navier-Stokes CFD simulations using the OVERFLOW flow solver are compared with high Reynolds test data obtained in the NASA Ames 12 Foot Pressure Wind Tunnel (PWT) facility. Computational analysis of the baseline HWT high-lift configuration with and without Externally Blown Flap (EBF) jet effects is highlighted. Several additional aerodynamic investigations, such as nacelle strake effectiveness and wake vortex studies, are presented. Technical capabilities and shortcomings of the computational method are discussed and summarized.

Slotnick, Jeffrey P.↗
NASA NTRS1992

Measurement and calibration of static distortion of position data from 3D trackers

Three-dimensional trackers are becoming increasingly important as user inputs in interactive computer systems. These trackers output the three-dimensional position, and often the orientation, of a sensor in space. The three-dimensional tracking is often, however, highly distorted and inaccurate. The purpose of this paper is to discuss methods for the measurement and characterization of the static distortion of the position data. When the distortion is constant, various methods can be used to calibrate the data from the tracker to increase accuracy. Several preliminary methods are discussed in this paper, including polynomial and weighted lookup methods. The measurement and calibration methods are applied to the Polhemus electromagnetic tracking system, but are applicable to tracking systems based on other technologies.

Bryson, Steve↗
NASA NTRS1991

Penn State axial flow turbine facility: Performance and nozzle flow field

The objective is to gain a thorough understanding of the flow field in a turbine stage including three-dimensional inviscid and viscid effects, unsteady flow field, rotor-stator interaction effects, unsteady blade pressures, shear stress, and velocity field in rotor passages. The performance of the turbine facility at the design condition is measured and compared with the design distribution. The data on the nozzle vane static pressure and wake characteristics are presented and interpreted. The wakes are found to be highly three-dimensional, with substantial radial inward velocity at most spanwise locations.

Lakshminarayana, B.↗
NASA NTRS1992

Identification of aerodynamic models for maneuvering aircraft

A Fourier analysis method was developed to analyze harmonic forced-oscillation data at high angles of attack as functions of the angle of attack and its time rate of change. The resulting aerodynamic responses at different frequencies are used to build up the aerodynamic models involving time integrals of the indicial type. An efficient numerical method was also developed to evaluate these time integrals for arbitrary motions based on a concept of equivalent harmonic motion. The method was verified by first using results from two-dimensional and three-dimensional linear theories. The developed models for C sub L, C sub D, and C sub M based on high-alpha data for a 70 deg delta wing in harmonic motions showed accurate results in reproducing hysteresis. The aerodynamic models are further verified by comparing with test data using ramp-type motions.

Lan, C. Edward↗
NASA NTRSDate not supplied

A Dynamic PCA and Machine Learning Tool for Automated Identification of Solar Wind Disturbances Impacting Earth’s Magnetosphere

Earth’s magnetosphere is continuously impacted by solar wind and interplanetary magnetic field (IMF) disturbances, such as shocks, discontinuities, magnetic clouds and more. Understanding how such disturbances propagate from the Sun and what is their impact on the different magnetospheric domains is key to understanding and forecasting energy transfer from the solar wind to Earth. The large number of overlapping solar wind and magnetospheric missions carrying magnetometers and the recent advances in communications and data storage technologies have enabled an unprecedented quantity of high-fidelity magnetic field data captured by in-situ spacecraft to be available at the click of a button. However, this massive quantity of available data can prove unwieldy for researchers, limiting the identification of interesting phenomena and disturbances to a relatively small percentage of the total dataset. Several techniques have been previously developed for automated identification of specific types of magnetic anomalies, but these methods are typically mission-specific and can be difficult to generalize. We present initial results for a generic method of automated anomaly detection in magnetic field measurements based on dimensionality reduction and unsupervised clustering via machine learning. The benefit of our technique is its high degree of generalizability and flexibility which make it a most useful data survey tool for a wide range of magnetic field datasets. This method can also be applied simultaneously to other observed time-series properties like plasma density, pressure, and velocity for more accurate event identification. Additionally, the application of this method to data captured by multiple spacecraft enables the simultaneous identification of disturbances and the determination of their propagation characteristics. Initial evaluation of this technique has been performed using data from Magnetospheric MultiScale (MMS) and THEMIS-ARTEMIS missions, providing a testbed scenario for the future Heliophysics Environmental and Radiation Measurement Experiment Suite (HERMES) platform instruments that will measure solar wind and IMF properties from lunar orbit onboard the Gateway station.

Miguel Martinez-Ledesma↗
NASA NTRSDate not supplied

A Dynamic PCA and Machine Learning Tool for Automated Identification of Solar Wind Disturbances Impacting Earth’s Magnetosphere

Earth’s magnetosphere is continuously impacted by solar wind and interplanetary magnetic field (IMF) disturbances, such as shocks, discontinuities, magnetic clouds and more. Understanding how such disturbances propagate from the Sun and what is their impact on the different magnetospheric domains is key to understanding and forecasting energy transfer from the solar wind to Earth. The large number of overlapping solar wind and magnetospheric missions carrying magnetometers and the recent advances in communications and data storage technologies have enabled an unprecedented quantity of high-fidelity magnetic field data captured by in-situ spacecraft to be available at the click of a button. However, this massive quantity of available data can prove unwieldy for researchers, limiting the identification of interesting phenomena and disturbances to a relatively small percentage of the total dataset. Several techniques have been previously developed for automated identification of specific types of magnetic anomalies, but these methods are typically mission-specific and can be difficult to generalize. We present initial results for a generic method of automated anomaly detection in magnetic field measurements based on dimensionality reduction and unsupervised clustering via machine learning. The benefit of our technique is its high degree of generalizability and flexibility which make it a most useful data survey tool for a wide range of magnetic field datasets. This method can also be applied simultaneously to other observed time-series properties like plasma density, pressure, and velocity for more accurate event identification. Additionally, the application of this method to data captured by multiple spacecraft enables the simultaneous identification of disturbances and the determination of their propagation characteristics. Initial evaluation of this technique has been performed using data from Magnetospheric MultiScale (MMS) and THEMIS-ARTEMIS missions, providing a testbed scenario for the future Heliophysics Environmental and Radiation Measurement Experiment Suite (HERMES) platform instruments that will measure solar wind and IMF properties from lunar orbit onboard the Gateway station.

Miguel Martinez-Ledesma↗