Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hybrid Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure : Severe Damage - Part II

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses a finite element analysis and the testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part II of the paper considers the final test to failure of the test article in the presence of an intentionally inflicted severe discrete source damage under the wing up-bending loading condition. Finite element analysis results are compared with measurements acquired during the test and demonstrate that the hybrid wing body test article was able to redistribute and support the required design loads in a severely damaged condition.

Przekop, Adam↗
NASA NTRS1981

Magnetic field diffusion and dissipation in reversed-field plasmas

A diffusion equation is derived which describes the evolution of a magnetic field in a plasma of arbitrary beta and resistivity. The equation is valid for a one-dimensional slab geometry, assumes the plasma remains in quasi-equilibrium throughout its evolution and does not include thermal transport. Scaling laws governing the rate of change of the magnetic energy, particle drift energy, and magnetic flux are calculated. It is found that the magnetic free energy can be substantially larger than the particle drift energy and can be an important energy reservoir in driving plasma instabilities (e.g., the lower-hybrid-drift instability). In addition, the effect of a spatially varying resistivity on the evolution of a reversed-field plasma is studied. The resistivity model used is based upon the anomalous transport properties associated with the nonlocal mode structure of the lower-hybrid-drift instability. The relevance of this research to laboratory plasmas (e.g., theta pinches, reversed-field theta pinches) and space plasmas (e.g., the earth's magnetotail) is discussed.

Drake, J. F.↗
NASA NTRS2016

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure: Ultimate Design Loads - Part 1

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses finite element analysis and testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part I of the paper considers the five most critical load conditions, which are internal pressure only and positive and negative g-loads with and without internal pressure. Analysis results are compared with measurements acquired during testing. Performance of the test article is found to be closely aligned with predictions and, consequently, able to support the hybrid wing body design loads in pristine and barely visible impact damage conditions.

Przekop, Adam↗
NASA NTRS2018

Evaluation of a Variable Thickness Hybrid Composite Bull Gear

For several years, NASA Glenn Research Center and the U.S. Army Research Laboratory have been investigating hybrid (compositesteel) gear technology for use in vertical lift drive systems. The hybrid gear concept replaces the structural portion of a gear between the shaft and the gear rim with a lightweight carbon fiber composite, in an effort to reduce the overall weight of a gear and increase the drive system power density. An overview of the concept of the hybrid gear design is described in Ref. 1, 2, and 3. The research presented in these references includes both small-scale and large-scale hybrid gear concepts all of which have a constant composite thickness throughout. The design described in this paper is of a variable thickness, such that the composite is thickest at the inner diameter and this thickness is gradually reduced toward the outer diameter. The resulting stair stepped design stems from dropping plies of the braided carbon fiber composite fabric gradually with increased radius. Additionally, the interlock pattern at the inner metallic adapter was adjusted slightly from previous designs to obtain a better stress distribution on the inner metallic adapter. The manufactured variable thickness web was tested both in static torsion tests and operationally in a relevant gearbox environment. The results of these experiments will be presented and compared to a baseline steel configuration.

Rotorcraft Propulsion↗
NASA NTRS1986

Evolution of the chromospheric and coronal activity of intermediate mass stars

Recent ultraviolet and X-ray observations pertaining to the outer atmospheric structure of intermediate mass (4-6 solar masses) stars and the evolution of their structure are presented. A distance-limited (d equal to or less than 200 pc) IUE ultraviolet survey of early K bright giants shows that C IV emission commonly is present. These stars are almost evenly split between stars showing hybrid-chromospheric and coronal outer atmospheric structures. Exosat observations have been obtained for three hybrid stars, of which only Alpha TrA, the nearest, is detected. The temperature of the emitting plasma is likely to be about 10 to the 6th K. Observtions of six K II stars made with the Einstein satellite show no detections. The general conclusion from the available X-ray data is that early K bright giants are not strong X-ray sources.

Brown, Alexander↗
NASA NTRS2017

Evaluation of a Variable Thickness Hybrid Composite Bull Gear

For several years, NASA Glenn Research Center and the U.S. Army Research Laboratory have been investigating hybrid (composite/steel) gear technology for use in vertical lift drive systems. The hybrid gear concept replaces the structural portion of a gear between the shaft and the gear rim with a lightweight carbon fiber composite, in an effort to reduce the overall weight of a gear and increase the drive system power density. Past research includes both small-scale and large-scale hybrid gear concepts, all of which have a constant composite thickness throughout. The design described in this paper is of a variable thickness, such that the composite is thickest at the inner diameter and this thickness is gradually reduced toward the outer diameter. The resulting "stair stepped" design stems from dropping plies of the braided carbon fiber prepreg composite fabric gradually with increased radius. Additionally, the interlock pattern at the inner metallic adapter was adjusted slightly from previous designs to obtain a better stress distribution on the inner metallic adapter. The manufactured variable thickness web was tested both in static torsion tests and operationally in a relevant gearbox environment. The results of these experiments will be presented and compared to a baseline steel configuration.

Gears; Drive Systems; Rotorcraft Propulsion;↗
NASA NTRS1995

Theoretical Study of Fe(CO)n-

The structures and CO binding energies are computed for Fe(CO)n- using a hybrid density functional theory (DFT) approach. The structures and ground states can be explained in terms of maximizing the Fe to CO 2pi* donation and minimizing Fe-CO 5 sigma repulsion. The trends in the CO binding energies for Fe(CO)n- and the differences between the trends for Fe(CO)n- and Fe(CO)n are also explained. For Fe(CO)n-, the second, third, and fourth CO bonding energies are in good agreement with experiment, while the first is too small. The first CO binding is also too small using the coupled cluster singles and doubles approach including a perturbation estimate of the connected triple excitations.

Ricca, Alessandra↗
NASA NTRS2019

A Design Methodology for Optimizing and Integrating Composite Materials in Gear Structures

The application of composite materials to gear structures is complex because of the gear shape, the need for precise dimensional tolerances, and the complex dynamic load condition. Methods are presented in this work to design and optimize an integrated composite hub-web structure that can be used as part of a hybrid composite-steel gear. The composite hub-web structure is a planar structure with a large decrease in thickness from the hub to the rim. Methods for design and optimization of this variable-thickness structure are presented along with a method for forming braided prepreg material to conform to the shape of this structure. A layered approach is presented that integrates cut plies or filler materials for thickness buildup with continuous-fiber layers for the primary load path. An additional gear design concept is presented that has an axially extended continuous-fiber composite structure that can be combined with the planar structure. A proposed optimization methodology is introduced where an optimized design is output for each type of optimization simulation. Through this process, composite knowledge can be incorporated in the optimization, and more control is given over the design during the process. The methods in this study provide a tool for designing and optimizing composite structures for gears and other high-power-density applications.

optimization↗
NASA NTRS1987

Anomalous transport in discrete arcs and simulation of double layers in a model auroral circuit

The evolution and long-time stability of a double layer (DL) in a discrete auroral arc requires that the parallel current in the arc, which may be considered uniform at the source, be diverted within the arc to charge the flanks of the U-shaped double layer potential structure. A simple model is presented in which this current redistribution is effected by anomalous transport based on electrostatic lower hybrid waves driven by the flank structure itself. This process provides the limiting constraint on the double layer potential. The flank charging may be represented as that of a nonlinear transmission line. A simplified model circuit, in which the transmission line is represented by a nonlinear impedance in parallel with a variable resistor, is incorporated in a one-dimensional simulation model to give the current density at the DL boundaries. Results are presented for the scaling of the DL potential as a function of the width of the arc and the saturation efficiency of the lower hybrid instability mechanism.

Smith, Robert A.↗
NASA NTRS1990

In-situ integrated processing and characterization of thin films of high temperature superconductors, dielectrics and semiconductors by MOCVD

In this strategy of depositing the basic building blocks of superconductors, semiconductors, and dielectric having common elements, researchers deposited superconducting films of Y-Ba-Cu-O, semiconductor films of Cu2O, and dielectric films of BaF2 and Y2O3 by metal oxide chemical vapor deposition (MOCVD). By switching source materials entering the chamber, and by using direct writting capability, complex device structures like three-terminal hybrid semiconductors/superconductors transistors can be fabricated. The Y-Ba-Cu-O superconducting thin films on BaF2/YSZ substrates show a T(sub c) of 80 K and are textured with most of the grains having their c-axis or a-axis perpendicular to the substrate. Electrical characteristics as well as structural characteristics of superconductors and related materials obtained by x-ray defraction, electron microscopy, and energy dispersive x-ray analysis are discussed.

Singh, R.↗
NASA NTRS2008

Structural Definition and Mass Estimation of Lunar Surface Habitats for the Lunar Architecture Team Phase 2 (LAT-2) Study

The Lunar Architecture Team Phase 2 study defined and assessed architecture options for a Lunar Outpost at the Moon's South Pole. The Habitation Focus Element Team was responsible for developing concepts for all of the Habitats and pressurized logistics modules particular to each of the architectures, and defined the shapes, volumes and internal layouts considering human factors, surface operations and safety requirements, as well as Lander mass and volume constraints. The Structures Subsystem Team developed structural concepts, sizing estimates and mass estimates for the primary Habitat structure. In these studies, the primary structure was decomposed into a more detailed list of components to be sized to gain greater insight into concept mass contributors. Structural mass estimates were developed that captured the effect of major design parameters such as internal pressure load. Analytical and empirical equations were developed for each structural component identified. Over 20 different hard-shell, hybrid expandable and inflatable soft-shell Habitat and pressurized logistics module concepts were sized and compared to assess structural performance and efficiency during the study. Habitats were developed in three categories; Mini Habs that are removed from the Lander and placed on the Lunar surface, Monolithic habitats that remain on the Lander, and Habitats that are part of the Mobile Lander system. Each category of Habitat resulted in structural concepts with advantages and disadvantages. The same modular shell components could be used for the Mini Hab concept, maximizing commonality and minimizing development costs. Larger Habitats had higher volumetric mass efficiency and floor area than smaller Habitats (whose mass was dominated by fixed items such as domes and frames). Hybrid and pure expandable Habitat structures were very mass-efficient, but the structures technology is less mature, and the ability to efficiently package and deploy internal subsystems remains an open issue.

Dorsey, John T.↗
NASA NTRS1995

The Structure of Li7 and K7

The self-consistent-field (SCF) approach and density functional theory, using the B3LYP hybrid functional, yield three low-lying structures for Li7(-). The relative separations differ for the SCF and B3LYP approaches, however the B3LYP results are in good agreement with the coupled cluster results. For K7(-), only an octahedron with one face capped is found to be a minimum; this the second most stable structure for Li7(-). A comparison of the computed separations between the low-lying states of K7 and the photoelectron detachment spectra does not allow an unambiguous assignment of the structure of K7(-).

Bauschlicher. Charles W., Jr.↗
NASA NTRS2004

Hybrid Inflatable Pressure Vessel

Figure 1 shows a prototype of a large pressure vessel under development for eventual use as a habitable module for long spaceflight (e.g., for transporting humans to Mars). The vessel is a hybrid that comprises an inflatable shell attached to a rigid central structural core. The inflatable shell is, itself, a hybrid that comprises (1) a pressure bladder restrained against expansion by (2) a web of straps made from high-strength polymeric fabrics. On Earth, pressure vessels like this could be used, for example, as portable habitats that could be set up quickly in remote locations, portable hyperbaric chambers for treatment of decompression sickness, or flotation devices for offshore platforms. In addition, some aspects of the design of the fabric straps could be adapted to such other items as lifting straps, parachute straps, and automotive safety belts. Figure 2 depicts selected aspects of the design of a vessel of this type with a toroidal configuration. The bladder serves as an impermeable layer to keep air within the pressure vessel and, for this purpose, is sealed to the central structural core. The web includes longitudinal and circumferential straps. To help maintain the proper shape upon inflation after storage, longitudinal and circumferential straps are indexed together at several of their intersections. Because the web is not required to provide a pressure seal and the bladder is not required to sustain structural loads, the bladder and the web can be optimized for their respective functions. Thus, the bladder can be sealed directly to the rigid core without having to include the web in the seal substructure, and the web can be designed for strength. The ends of the longitudinal straps are attached to the ends of the rigid structural core by means of clevises. Each clevis pin is surrounded by a roller, around which a longitudinal strap is wrapped to form a lap seam with itself. The roller is of a large diameter chosen to reduce bending of the fibers in the strap. The roller also serves to equalize the load in the portions of the strap on both sides of the clevis pin. The lap seam is formed near the clevis by use of a tapered diamond stitch: This stitch is designed specifically to allow fibers in the stitch and strap to relax under load in such a manner that the load becomes more nearly evenly distributed among all fibers in the stitch region. Thus, the tapered diamond stitch prevents load concentrations that could cause premature failure of the strap and thereby increases the strength of the strap/structural-core joint. The lap seam can be rated at >90 percent of the strength of the strap material.

Raboin, Jasen↗
NASA NTRS1987

Anomalous transport in discrete arcs and simulation of double layers in a model auroral circuit

The evolution and long-time stability of a double layer in a discrete auroral arc requires that the parallel current in the arc, which may be considered uniform at the source, be diverted within the arc to charge the flanks of the U-shaped double-layer potential structure. A simple model is presented in which this current re-distribution is effected by anomalous transport based on electrostatic lower hybrid waves driven by the flank structure itself. This process provides the limiting constraint on the double-layer potential. The flank charging may be represented as that of a nonlinear transmission. A simplified model circuit, in which the transmission line is represented by a nonlinear impedance in parallel with a variable resistor, is incorporated in a 1-d simulation model to give the current density at the DL boundaries. Results are presented for the scaling of the DL potential as a function of the width of the arc and the saturation efficiency of the lower hybrid instability mechanism.

Smith, Robert A.↗
NASA NTRS2002

Design, Fabrication, and Testing of Composite Energy-Absorbing Keel Beams for General Aviation Type Aircraft

A lightweight energy-absorbing keel-beam concept was developed and retrofitted in a general aviation type aircraft to improve crashworthiness performance. The energy-absorbing beam consisted of a foam-filled cellular structure with glass fiber and hybrid glass/kevlar cell walls. Design, analysis, fabrication and testing of the keel beams prior to installation and subsequent full-scale crash testing of the aircraft are described. Factors such as material and fabrication constraints, damage tolerance, crush stress/strain response, seat-rail loading, and post crush integrity, which influenced the course of the design process are also presented. A theory similar to the one often used for ductile metal box structures was employed with appropriate modifications to estimate the sustained crush loads for the beams. This, analytical tool, coupled with dynamic finite element simulation using MSC.Dytran were the prime design and analysis tools. The validity of the theory as a reliable design tool was examined against test data from static crush tests of beam sections while the overall performance of the energy-absorbing subfloor was assessed through dynamic testing of 24 in long subfloor assemblies.

Kellas, Sotiris↗
NASA NTRS1986

Comparison of modal identification techniques using a hybrid-data approach

Modal identification of seemingly simple structures, such as the generic truss is often surprisingly difficult in practice due to high modal density, nonlinearities, and other nonideal factors. Under these circumstances, different data analysis techniques can generate substantially different results. The initial application of a new hybrid-data method for studying the performance characteristics of various identification techniques with such data is summarized. This approach offers new pieces of information for the system identification researcher. First, it allows actual experimental data to be used in the studies, while maintaining the traditional advantage of using simulated data. That is, the identification technique under study is forced to cope with the complexities of real data, yet the performance can be measured unquestionably for the artificial modes because their true parameters are known. Secondly, the accuracy achieved for the true structural modes in the data can be estimated from the accuracy achieved for the artificial modes if the results show similar characteristics. This similarity occurred in the study, for example, for a weak structural mode near 56 Hz. It may even be possible--eventually--to use the error information from the artificial modes to improve the identification accuracy for the structural modes.

Pappa, Richard S.↗
NASA NTRS2015

Preliminary Weight Savings Estimate for a Commercial Transport Wing Using Rod-Stiffened Stitched Composite Technology

A structural concept called pultruded rod stitched efficient unitized structure (PRSEUS) was developed by the Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration. While PRSEUS was an enabling technology for the pressurized HWB structure, limited investigation of PRSEUS for other aircraft structures, such as circular fuselages and wings, has been done. Therefore, a study was undertaken to investigate the potential weight savings afforded by using the PRSEUS concept for a commercial transport wing. The study applied PRSEUS to the Advanced Subsonic Technology (AST) Program composite semi-span test article, which was sized using three load cases. The initial PRSEUS design was developed by matching cross-sectional stiffnesses for each stringer/skin combination within the wing covers, then the design was modified to ensure that the PRSEUS design satisfied the design criteria. It was found that the PRSEUS wing design exhibited weight savings over the blade-stiffened composite AST Program wing of nearly 9%, and a weight savings of 49% and 29% for the lower and upper covers, respectively, compared to an equivalent metallic wing.

Lovejoy, Andrew E.↗
NASA NTRS1992

Starbursts in the nuclei of shell galaxies

Simulations of shell-forming galaxy mergers are reported in which gas and stars are tracked separately to study the implications of observations that indicate fine structures in elliptical galaxies. The hybrid N-body/hydrodynamics code by Hernquist and Katz (1989) is employed neglecting the self-gravity of galaxies in tidal disruptions by massive primaries of small dwarf galaxies. The evolution of the galactic debris is examined showing that the gas and stars are effectively segregated with the stars forming sharp-edged features and the gas forming disks in the nucleus of the primary. Star formation is theorized to occur in the nuclei of shell galaxies due to shocks in the gas, and the added presence of a black hole can lead to an active galactic nucleus. The simulation is of interest to the interpretation of such observations as those of NGC1275 in which dormant elliptical galaxies are activated by mergers between large galaxies and gas-rich satellites.

Hernquist, Lars↗