Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hydrogen Diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Effect of low-energy hydrogen ion implantation on dendritic web silicon solar cells

The effect of a low-energy (0.4 keV), short-time (2-min), heavy-dose (10 to the 18th/sq cm) hydrogen ion implant on dendritic web silicon solar cells and material was investigated. Such an implant was observed to improve the cell open-circuit voltage and short-circuit current appreciably for a number of cells. In spite of the low implant energy, measurements of internal quantum efficiency indicate that it is the base of the cell, rather than the emitter, which benefits from the hydrogen implant. This is supported by the observation that the measured minority-carrier diffusion length in the base did not change when the emitter was removed. In some cases, a threefold increase of the base diffusion length was observed after implantation. The effects of the hydrogen implantation were not changed by a thermal stress test at 250 C for 111 h in nitrogen. It is speculated that hydrogen enters the bulk by traveling along dislocations, as proposed recently for edge-defined film-fed growth silicon ribbon.

Rohatgi, A.↗
NASA NTRS1990

Energy balance in the solar transition region. I - Hydrostatic thermal models with ambipolar diffusion

The energy balance in the lower transition region is analyzed by constructing theoretical models which satisfy the energy balance constraint. The energy balance is achieved by balancing the radiative losses and the energy flowing downward from the corona. This energy flow is mainly in two forms: conductive heat flow and hydrogen ionization energy flow due to ambipolar diffusion. Hydrostatic equilibrium is assumed, and, in a first calculation, local mechanical heating and Joule heating are ignored. In a second model, some mechanical heating compatible with chromospheric energy-balance calculations is introduced. The models are computed for a partial non-LTE approach in which radiation departs strongly from LTE but particles depart from Maxwellian distributions only to first order. The results, which apply to cases where the magnetic field is either absent, or uniform and vertical, are compared with the observed Lyman lines and continuum from the average quiet sun. The approximate agreement suggests that this type of model can roughly explain the observed intensities in a physically meaningful way, assuming only a few free parameters specified as chromospheric boundary conditions.

Fontenla, J. M.↗
NASA NTRS1974

Short-range interaction between hydrogen molecules

Recent calculations of the ground state energy of a system of four hydrogen atoms are reviewed with the aim of discerning the short-range repulsive part of the interaction potential between two hydrogen molecules. Extended-basis CI calculations which include a diffuse 2p orbital appear to be capable of determining the total interaction energy between to hydrogen molecules for any separation. Consistent results of such calculations suggest that the potential for intermolecular separations in the region from 1 to 2.5 A can now be specified to better than 10% with considerable confidence. Analytic fits to spherical averages of these results are presented.

Mcmahan, A. K.↗
NASA NTRS1986

Fatigue of 1018 steel in hydrogen

Tests are performed at different hydrogen pressures and mechanical load parameter values (applied load, stress concentration factor, applied load frequency) to study enhanced fatigue crack growth in SAE 1018 steel. Oxygen was introduced as a hydrogen-oxygen gas mixture environment in order to compare the role of oxygen in crack inhibition with that previously reported for both static and cyclic loading of higher strength steels. In a number of experiments, a thin film of palladium was applied to the specimen surface to facilitate the study of steel-hydrogen interaction in the absence of any surface impedance to hydrogen entry. The kinetics of the diffusing atoms are found to be influenced by the stress field around the notch tip and the applied frequency. An increment in environmental effect occurred when applied load or stress concentration factor was increased.

Lo, S. H.↗
NASA NTRS1989

A survey of upwind methods for flows with equilibrium and non-equilibrium chemistry and thermodynamics

Several versions of flux-vector split and flux-difference split algorithms were compared with regard to general applicability and complexity. Test computations were performed using curve-fit equilibrium air chemistry for an M = 5 high-temperature inviscid flow over a wedge, and an M = 24.5 inviscid flow over a blunt cylinder for test computations; for these cases, little difference in accuracy was found among the versions of the same flux-split algorithm. For flows with nonequilibrium chemistry, the effects of the thermodynamic model on the development of flux-vector split and flux-difference split algorithms were investigated using an equilibrium model, a general nonequilibrium model, and a simplified model based on vibrational relaxation. Several numerical examples are presented, including nonequilibrium air chemistry in a high-temperature shock tube and nonequilibrium hydrogen-air chemistry in a supersonic diffuser.

Grossman, B.↗
NASA NTRS1989

Can the Exosat observations of DA white dwarfs be explained by layered atmospheric structures?

It is demonstrated that the Exosat broadband filter observations of DA white dwarfs, which have recently been interpreted with homogeneously mixed H/He atmospheres (Jordan et al, 1987; Paerels and Heise, 1989), can be explained with stratified theoretical models. In these models a very thin H layer is floating on top of the underlying He. The transition zone is determined by diffusive equilibrium. The resulting total hydrogen-layer masses are in the range (3-500) x 10 to the -16th solar mass. Several arguments are discussed that could lead to a decision about the correct interpretation, but a final answer is not possible.

Koester, D.↗
NASA NTRS1989

OH-asterisk (7-5) Meinel band dayglow and nightglow measured by the SME limb scanning near infrared spectrometer - Comparison of the observed seasonal variability with two-dimensional model simulations

Seasonal variations of the OH-asterisk (7-5) mesospheric hydroxyl emission at 1.89 microns observed by the SME near-IR spectrometer are compared with the theoretical predictions of a two-dimensional dynamical/chemical model. The good agreement found at low latitudes for both dayglow and nightglow provides support for the model assumption that breaking gravity waves induce seasonal and latitudinal variations in diffusion. The seasonal behavior of atomic hydrogen in the upper mesosphere (related to vertical transport) and/or uncertainties in the OH Meinel band parameters are proposed as possible explanations for the discrepancy noted between model and observational data for the middle latitudes.

Le Texier, H.↗
NASA NTRS1995

Energization and transport of ions of ionospheric origin in the terrestrial magnetosphere

The work of this grant has been predominantly focused on ion outflows from two data sets: Prognoz 7 and Dynamics Explorer. The Prognoz analysis studied ion densities, temperatures, and flow velocities in the magnetotail. The work performed under this contract consisted of developing a program to load the raw data, computing the background subtraction of a strong sun pulse, and using the net count to calculate the low order moments of the distribution function. The study confirms the results of ISEE with regard to the supply of plasma from the cusp as a major source of plasmasheet plasma and goes beyond this to discuss the use of ion velocities as a way to examine the motions of the magnetotail. The abstract of the work to be reported is included as an appendix. The work on the DE/Retarding Ion Mass Spectrometer is separated into two categories: (1) classification of low-energy ion flows from high-latitudes, and (2) studies of the polar wind. Major publications resulting from this work are also included as an appendix to this report. The polar wind is in a category by itself as a result of the thermal escape of hydrogen and helium because of ambipolar diffusion through the heavier, oxygen-dominated topside ionosphere. The analysis of the polar wind reports the flux variability as a function of season, magnetic activity, etc. Much effort has been expended under this grant to complete a follow on study of the thermal structure of the polar wind. Extensive display tools and analysis software have been developed and used in an attempt to carry out this thermal analysis. The present work uses a constrained fit scheme that combines the ion densities and flow velocities derived from Chandler et al. and a spacecraft potential derived from an empirical relation to the total ion density to determine the remaining fit parameter, the ion temperature, via a least squares fit to the RIMS data.

Waite, J. Hunter JR.↗
NASA NTRS1999

Parametric Studies of the Ejector Process within a Turbine-Based Combined-Cycle Propulsion System

Performance characteristics of the ejector process within a turbine-based combined-cycle (TBCC) propulsion system are investigated using the NPARC Navier-Stokes code. The TBCC concept integrates a turbine engine with a ramjet into a single propulsion system that may efficiently operate from takeoff to high Mach number cruise. At the operating point considered, corresponding to a flight Mach number of 2.0, an ejector serves to mix flow from the ramjet duct with flow from the turbine engine. The combined flow then passes through a diffuser where it is mixed with hydrogen fuel and burned. Three sets of fully turbulent Navier-Stokes calculations are compared with predictions from a cycle code developed specifically for the TBCC propulsion system. A baseline ejector system is investigated first. The Navier-Stokes calculations indicate that the flow leaving the ejector is not completely mixed, which may adversely affect the overall system performance. Two additional sets of calculations are presented; one set that investigated a longer ejector region (to enhance mixing) and a second set which also utilized the longer ejector but replaced the no-slip surfaces of the ejector with slip (inviscid) walls in order to resolve discrepancies with the cycle code. The three sets of Navier-Stokes calculations and the TBCC cycle code predictions are compared to determine the validity of each of the modeling approaches.

Georgiadis, Nicholas J.↗
NASA NTRS1973

Determination of hydrogen in milligram quantities of titanium and its alloys

An accurate, versatile, and sensitive method for the determination of hydrogen in milligram-size titanium samples is presented. It involves extraction of hydrogen at 1070 K while a mercury diffusion pump transfers the evolved gases into the inlet of a mass spectrometer. All the evolved gases may then be positively identified and determined. This method can be readily adapted for use with other metals and for the study of the slow evolution of hydrogen. Reduction of interferences due to the evolution of hydrogen by reactions involving vapors such as those of water, acetone, and vacuum grease is discussed.

Otterson, D. A.↗
NASA NTRS2006

New Propellants and Cryofuels

The proposed research will investigate the stability and cryogenic properties of solid propellants that are critical to NASA s goal of realizing practical propellant designs for future spacecraft. We will determine the stability and thermal properties of a solid hydrogen-liquid helium stabilizer in a laboratory environment in order to design a practical propellant. In particular, we will explore methods of embedding atomic species and metallic nano-particulates in hydrogen matrices suspended in liquid helium. We will also measure the characteristic lifetimes and diffusion of atomic species in these candidate cryofuels. The most promising large-scale advance in rocket propulsion is the use of atomic propellants; most notably atomic hydrogen stabilized in cryogenic environments, and metallized-gelled liquid hydrogen (MGH) or densified gelled hydrogen (DGH). The new propellants offer very significant improvements over classic liquid oxygen/hydrogen fuels because of two factors: (1) the high energy-release, and (ii) the density increase per unit energy release. These two changes can lead to significant reduced mission costs and increased payload to orbit weight ratios. An achievable 5 to 10 percent improvement in specific impulse for the atomic propellants or MGH fuels can result in a doubling or tripling of system payloads. The high-energy atomic propellants must be stored in a stabilizing medium such as solid hydrogen to inhibit or delay their recombination into molecules. The goal of the proposed research is to determine the stability and thermal properties of the solid hydrogen-liquid helium stabilizer. Magnetic resonance techniques will be used to measure the thermal lifetimes and the diffusive motions of atomic species stored in solid hydrogen grains. The properties of metallic nano-particulates embedded in hydrogen matrices will also be studied and analyzed. Dynamic polarization techniques will be developed to enhance signal/noise ratios in order to be able to detect low concentrations of the introduced species. The required lifetimes for atomic hydrogen and other species can only be realized at low temperatures to avoid recombination of atoms before use as a fuel.

Palasezski, Bryan↗
NASA NTRS1974

Mariner 6, 7, and 9 ultraviolet spectrometer experiment - Analysis of hydrogen Lyman alpha data

Four Lyman alpha airglow measurements of the limb and disk of Mars, made by ultraviolet spectrometers on Mariner 6 and 7 in 1969 and Mariner 9 in 1971, are analyzed to determine the amount and distribution of atomic hydrogen above 80 km. The variation of atomic hydrogen with altitude is calculated by using time-independent chemical diffusion models from 80 to 250 km, and an exospheric model is used above 250 km. By employing radiative transfer theory that includes effects of pure absorption and accounts for temperature variations in the atmosphere, a spherical model of the airglow Lyman alpha emission is used to produce theoretical intensities for comparison with the data. It is found that (1) the exospheric temperature and distribution in 1971 are consistent with those determined in 1969, (2) the vertical optical depth above 80 km was 2.2 in 1969 and 5 in 1971, and (3) the derived atomic hydrogen distribution from 80 to 250 km requires a source of atomic hydrogen above 80 km. Comparison of observed profiles with chemical diffusion models implies a large downward flow of atomic hydrogen at 80 km coupled with a large upward flow of molecular hydrogen.-

Anderson, D. E., Jr.↗
NASA NTRS1967

Visualization of hydrogen fires.

Hydrogen fire visualization detection techniques including application of photography, TV and image converter in IR and UV regions

ULTRAVIOLET RADIATION↗
NASA NTRS1965

Radiative shock structure.

Shock wave structure in ionized hydrogen, using Eddington approximation to solve Rankine- Hugoniot jump equation

DIFFUSION WAVE↗
NASA NTRS1994

The Prediction of Nozzle Performance and Heat Transfer in Hydrogen/Oxygen Rocket Engines with Transpiration Cooling, Film Cooling, and High Area Ratios

An advanced engineering computational model has been developed to aid in the analysis of chemical rocket engines. The complete multispecies, chemically reacting and diffusing Navier-Stokes equations are modelled, including the Soret thermal diffusion and Dufour energy transfer terms. Demonstration cases are presented for a 1030:1 area ratio nozzle, a 25 lbf film-cooled nozzle, and a transpiration-cooled plug-and-spool rocket engine. The results indicate that the thrust coefficient predictions of the 1030:1 nozzle and the film-cooled nozzle are within 0.2 to 0.5 percent, respectively, of experimental measurements. Further, the model's predictions agree very well with the heat transfer measurements made in all of the nozzle test cases. It is demonstrated that thermal diffusion has a significant effect on the predicted mass fraction of hydrogen along the wall of the nozzle and was shown to represent a significant fraction of the diffusion fluxes occurring in the transpiration-cooled rocket engine.

Kacynski, Kenneth J.↗
NASA NTRS1981

Recent work in advanced hydrogen production concepts

The hydrogen photoelectrolytic conversion activity investigated the practicability of semiconductor electrolytic devises that use solar energy to decompose water into hydrogen and oxygen in an apparent single step process. The photocatalytic decomposition of inorganic hydrogen compounds; i.e., hydrobromic and hydriodic acids using rhodium organic bridge complexes were also studied. The feasibility of direct high temperature thermal decompositions of water with diffusion processes for separation of the equilibrium mixture of hydrogen and oxygen into usable energy sources was examined.

Lawson, D. D.↗
NASA NTRS1982

Gas-phase hydrogen permeation through alpha-titanium - Surface film and dimensional effects

The process of hydrogen transport through alpha-Ti involves simultaneous diffusion and phase boundary reactions at both surfaces, with the relative effect on each surface depending on the extent of surface contamination as well as the physical dimensions of the titanium membrane used. It is shown by the present study that hydrogen permeation in commercially pure alpha-Ti increases exponentially with temperature and is dependent on the first power of the input pressure, whether the surface is as-polished, preoxidized or prenitrided. Permeation decreases in the case of the as-polished condition if nitride or oxide films are formed at the surface in contact with source hydrogen, while increasing slightly for the same condition if such films are formed at the hydrogen exit surface.

Shah, K. K.↗