SEARCH · Search NASA

Results for “IGNITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Ignition of partially shattered liquid fuel drops in a reflected shock wave environment

An experimental investigation of the ignition of individual fuel drops after their interaction with an incident and a reflected shock wave near the end wall of a shock tube has been carried out. The influence of the aerodynamic shattering of the fuel drop by the convective flow on the ignition characteristics has been examined by varying the drop-end wall separation distance. Data are presented which show the ignition delay times to be a function of the various experimental conditions encountered in this study. A comparison is made with previous investigations concerning the ignition of a liquid fuel drop due only to the interaction with an incident shock wave.

Wierzba, A. S.↗

NASA NTRS1977

Study of igniter design and applications to low smoke solid rockets

A simple analysis of igniter design is described which is sufficiently general to be applicable to any 'basket'-type housing containing one or more charges. The gas equation of state is used in conjunction with the experimentally determined propellant burning-rate law to predict the pressure-time histories in the igniter housing and the rocket motor. Typical numerical results are presented for three cases which represent three experimental conditions tested in a project on low-smoke motors where the requirements on the exhaust were sufficiently stringent to preclude condensible matter from the igniter. Pressure was measured continuously in time at two locations in the igniter housing and at the head end of the motor case. The agreement between theoretical and experimental results is felt to be encouraging considering the complexity of the problem and the many simplifications in the analysis.

Ramohalli, K.↗

NASA NTRS1977

The use of the high flux heater in the smoke chamber to measure ignitability and smoke evolution of composite panels

Ten samples of composite panels were evaluated in the smoke chamber using a high flux heater to produce heat flux levels up to 9.5 watts per square cm. This study demonstrated the potential of the apparatus as a means of evaluating ignitability as well as smoke evolution. Depending on the material and the heat flux level, ignitability results ranged from ignition within 2 seconds to no ignition during the test period. Smoke density generally increased with increasing heat flux. A composite panel consisting of bismaleimide-fiberglass/bismaleimide honeycomb with carbon microballoons exhibited the lowest smoke density at high heat flux levels and the greatest resistance to autoignition.

Hilado, C. J.↗

NASA NTRS1979

Criteria for self-ignition of supersonic hydrogen-air mixtures

A correlation of available self ignition data for supersonic hydrogen-air mixtures in configurations representative of scramjet combustors was made. The correlation was examined in light of simplified ignition-limit models. The data and model included cases of injection from transverse fuel jets on walls, transverse jets behind swept and unswept steps, and transverse injection ahead of swept and unswept steps and strut bases. The results provide useful guidance for predicting self ignition in a variety of applications. The likely regions for self ignition in a combustor are given in order of merit.

Huber, P. W.↗

NASA NTRS1980

Convective heating of solid propellant during ignition

A pattern search optimization procedure is used to deduce from test data on the solid rocket boosters of the Space Shuttle the convective heat transfer coefficients between the igniter and main motor combustion gases and the surface of the solid propellant by utilizing a spatial and temporal ignition transient analysis. The 'best' convective coefficients are found which will minimize the overall deviation of the analytical prediction from the ignition transient test data. Computationally, this is achieved by treating the motor in such a way that only four optimization variables must be determined. The resulting coefficients greatly improve the prediction capabilities of the ignition transient analysis for the Space Shuttle SRM.

Murph, J. E.↗

NASA NTRS1983

Ignition of SiH4-H2-O2-N2 behind reflected shock waves

The ignition of mixtures of silane, hydrogen, and oxygen diluted with nitrogen was studied in a chemical kinetic shock tube. Ignition delay time measurements were made behind reflected shock waves at pressures of 1.25 atm and 1.35 atm and temperatures ranging from approximately 800 K to 1050 K for two mixtures with silane-oxygen equivalence ratios of 1.0 and 0.5, respectively. Enhancement of the ignition by use of silane was observed experimentally by the failure of a similar mixture containing only hydrogen, oxygen, and nitrogen to ignite during the maximum test time available for these test conditions.

Mclain, A. G.↗

NASA NTRS1983

Experimental and theoretical study of combustion jet ignition

A combustion jet ignition system was developed to generate turbulent jets of combustion products containing free radicals and to discharge them as ignition sources into a combustible medium. In order to understand the ignition and the inflammation processes caused by combustion jets, the studies of the fluid mechanical properties of turbulent jets with and without combustion were conducted theoretically and experimentally. Experiments using a specially designed igniter, with a prechamber to build up and control the stagnation pressure upstream of the orifice, were conducted to investigate the formation processes of turbulent jets of combustion products. The penetration speed of combustion jets has been found to be constant initially and then decreases monotonically as turbulent jets of combustion products travel closer to the wall. This initial penetration speed to combustion jets is proportional to the initial stagnation pressure upstream of the orifice for the same stoichiometric mixture. Computer simulations by Chorin's Random Vortex Method implemented with the flame propagation algorithm for the theoretical model of turbulent jets with and without combustion were performed to study the turbulent jet flow field. In the formation processes of the turbulent jets, the large-scale eddy structure of turbulence, the so-called coherent structure, dominates the entrainment and mixing processes. The large-scale eddy structure of turbulent jets in this study is constructed by a series of vortex pairs, which are organized in the form of a staggered array of vortex clouds generating local recirculation flow patterns.

Chen, D. Y.↗

NASA NTRS1984

Ignition phenomena of bulk aluminum alloy as a function of oxygen pressure

An ignition phenomena of 6061 aluminum alloy was investigated as a function of oxygen pressure. Cylindrical aluminum alloy specimens were ignited in a pure oxygen environment by a focused CW CO2 laser beam. The experiments were conducted at oxygen pressures ranging from 0.084 to 2.413 MPa. The temperature history of the entire upper surface of the specimen and of a 0.5 mm diameter spot located initially at the center of the specimen top surface was recorded by using a commercial two-color ratio pyrometer and a fast-response, narrow-band, two-color pyrometer. Mass, brightness, and interior temperatures (for certain experiments) were also recorded throughout the experiment. The results show that the surface temperatures at ignition of the alloy obtained from the temperature curves are below the melting temperature of the aluminum oxide and are slightly dependent on oxygen pressure. The data indicate that the ignition mechanism is complex and probably composed of several phenomena acting both separately and in conjunction with each other.

Nguyen, K.↗

NASA NTRS1986

Methane oxidation behind reflected shock waves: Ignition delay times measured by pressure and flame band emission

Ignition delay data were recorded for three methane-oxygen-argon mixtures (phi = 0.5, 1.0, 2.0) for the temperature range 1500 to 1920 K. Quiet pressure trances enabled us to obtain delay times for the start of the experimental pressure rise. These times were in good agreement with those obtained from the flame band emission at 3700 A. The data correlated well with the oxygen and methane dependence of Lifshitz, but showed a much stronger temperature dependence (phi = 0.5 delta E = 51.9, phi = 1.0 delta = 58.8, phi = 2.0 delta E = 58.7 Kcal). The effect of probe location on the delay time measurement was studied. It appears that the probe located 83 mm from the reflecting surface measured delay times which may not be related to the initial temperature and pressure. It was estimated that for a probe located 7 mm from the reflecting surface, the measured delay time would be about 10 microseconds too short, and it was suggested that delay times less than 100 microsecond should not be used. The ignition period was defined as the time interval between start of the experimental pressure rise and 50 percent of the ignition pressure. This time interval was measured for three gas mixtures and found to be similar (40 to 60 micro sec) for phi = 1.0 and 0.5 but much longer (100 to 120) microsecond for phi = 2.0. It was suggested that the ignition period would be very useful to the kinetic modeler in judging the agreement between experimental and calculated delay times.

Brabbs, T. A.↗

NASA NTRS1986

Ignition and combustion temperatures determined by laser heating

A laser heating technique and facility have been developed to study metal ignition and combustion in high-pressure oxygen. The ignition and combustion temperatures, estimates of oxidation rates, and ignition and combustion morphology can be determined. This facility and the laser heating techniques are described. Examples of the type of data obtained are presented and discussed. The ignition temperature curves for an aluminum alloy - Unified Numbering System (UNS) A96061, a stainless steel - UNS S30200, and two nickel alloys - UNS N07718 and N04400 are given.

Bransford, J. W.↗

NASA NTRS1989

Igniter Simulator

Report describes electronic circuitry that simulates electrical properties of igniter of Space Shuttle main engine. Circuit used to test software of engine controller, without having to fire real igniter or turn on engine. Circuit used in all igniter simulations and mimics operation of igniter more realistically than did previous versions.

Simon, Richard A.↗

NASA NTRS1989

A premixed hydrogen/oxygen catalytic igniter

The catalytic ignition of hydrogen and oxygen propellants was studied using a premixing hydrogen/oxygen injector. The premixed injector was designed to eliminate problems associated with catalytic ignition caused by poor propellant mixing in the catalyst bed. Mixture ratio, mass flow rate, and propellant inlet temperature were varied parametrically in testing, and a pulse mode life test of the igniter was conducted. The results of the tests showed that the premixed injector eliminated flame flashback in the reactor and increased the life of the igniter significantly. The results of the experimental program and a comparison with data collected in a previous program are given.

Green, James M.↗

NASA NTRS1988

Ignition of contaminants by impact of high-pressure oxygen

The ignition of oil-film contaminants in high-pressure gaseous oxygen systems, caused by rapid pressurization, was investigated using the NASA/White Sands Test Facility's large-volume pneumatic impact test system. The test section consisted of stainless steel lines, contaminated on the inside surface with known amounts of Mobil DTE 24 oil and closed at one end, which was attached to a high-pressure oxygen system; the test section was pressurized to 48 MPa by opening a high-speed valve. Ignition of the oil was detected by a photocell attached to the closed end of the line. It was found that the frequency of ignition increased as a function of both the concentration of oil and of the pressure of the impacting oxygen. The threshold of ignition was between 25 and 65 mg/sq m. The results were correlated with the present NASA and Compressed Gas Association requirements for maximum levels of organic contaminants.

Pedley, Michael D.↗

NASA NTRS1988

Evaporation, ignition and combustion of nondilute clusters of drops

A theory of evaporation, ignition, and burning of moderately dense spherical drop clusters has been developed. The theory takes into account burning of premixed air and fuel internal to the cluster at ignition and subsequent burning of fuel emitted from the cluster by a flame sheet surrounding it. The model considers interdrop interaction, momentum exchange between drops and gas, and turbulent exchange processes between the cluster and its surroundings. Calcualtions are performed for varying initial air to fuel mass ratios, initial cluster radii, ambient gas temperatures, and initial drop temperatures. Results are presented for fuel burn fractions at ignition and at the moment of drop disappearance, as well as jump conditions at ignition.

Bellan, J.↗

NASA NTRS1989

A premixed hydrogen/oxygen catalytic igniter

Green, James M.↗

NASA NTRS1990

Mars in situ propellants: Carbon monoxide and oxygen ignition experiments

Carbon monoxide and oxygen were tested in a standard spark-torch igniter to identify the ignition characteristics of this potential Mars in situ propellant combination. The ignition profiles were determined as functions of mixture ratio, amount of hydrogen added to the carbon monoxide, and oxygen inlet temperature. The experiments indicated that the carbon monoxide and oxygen combination must have small amounts of hydrogen present to initiate reaction. Once the reaction was started, the combustion continued without the presence of hydrogen. A mixture ratio range was identified where ignition occurred, and this range varied with the oxygen inlet temperature.

Linne, Diane L.↗

NASA NTRS1990

Mars in situ propellants - Carbon monoxide and oxygen ignition experiments

Linne, Diane L.↗

NASA NTRS1990

Transverse liquid fuel jet breakup, burning, and ignition

An analytical study of the breakup, burning, and ignition of liquid fuels injected transversely into a hot air stream is conducted. The non-reacting liquid jet breakup location is determined by the local sonic point criterion. Two models, one employing analysis of an elliptical jet cross-section and the other employing a two-dimensional blunt body to represent the transverse jet, were used for sonic point calculations. An auxiliary criterion based on surface tension stability is used as a separate means of determining the breakup location. For the reacting liquid jet problem, a diffusion flame supported by a one-step chemical reaction within the gaseous boundary layer is solved along the ellipse surface in subsonic cross flow. Typical flame structures and concentration profiles were calculated for various locations along the jet cross-section as a function of upstream Mach numbers. The integration reaction rate along the jet cross-section is used to predict ignition position, which is found to be situated near the stagnation point. While a multi-step reaction is needed to represent the ignition process more accurately, the present calculation does yield reasonable predictions concerning ignition along a curved surface.

Li, Hsi-Shang↗