Search NASA⌕ Search

SEARCH · Search NASA

Results for “In situ characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Super-resolution imaging reveals resistance to mass transfer in functionalized stationary phases

Chemical separations are costly in terms of energy, time, and money. Separation methods are optimized with inefficient trial-and-error approaches that lack insight into the molecular dynamics that lead to the success or failure of a separation and, hence, ways to improve the process. We perform super-resolution imaging of fluorescent analytes in five different commercial liquid chromatography materials. Unexpectedly, we observe that chemical functionalization can block more than 50% of the material’s porous interior, rendering it inaccessible to small-molecule analytes. Only in situ imaging unveils the inaccessibility when compared to the industry-accepted ex situ characterization methods. Selectively removing some of the functionalization with solvent restores pore access without substantially altering the single-molecule kinetics that underlie the separation and agree with bulk chromatography measurements. Our molecular results determine that commercial “fully porous” stationary phases are over-functionalized and provide an alternative avenue to characterize and direct separation material design from the bottom-up.

Science & Technology - Other Topics↗
DOE OSTI2021

Mitigation of PtCo/C Cathode Catalyst Degradation via Control of Relative Humidity

Maintaining the high performance of proton-exchange membrane fuel cells (PEMFC) over the course of its lifetime is a key enabling factor for its successful commercialization as a primary power source in zero-emission transportation applications. In this context, it is important to mitigate the degradation of PtCo-alloy based cathode catalysts used for oxygen reduction reaction (ORR). PtCo-alloy catalysts exhibit high activity at beginning-of-life (BOL) which tends to decrease during operation due to loss of electrochemical surface area (ECSA) and dissolution-contamination related effects of the Co-alloying component. Here, we demonstrate the use of relative humidity (RH) of the inlet gases as a controllable parameter to mitigate the degradation of PtCo-alloy catalyst degradation. We employ a catalyst-specific voltage cycling accelerated stress test (AST) durability protocol as a function of inlet RH to degrade PtCo catalysts. A series of in situ electrochemical diagnostics and ex situ characterizations have been carried out to investigate the catalyst layer characteristics at end-of-test (EOT). Our results show that at sub-saturated conditions of durability protocol operation, PtCo catalyst sustains higher EOT H 2 /air performance due to better retention of ECSA and smaller impact of Co 2+ dissolution/contamination.

25 ENERGY STORAGE↗
DOE OSTI2025

Degradation of Fuel Cell Membrane Electrode Assemblies from Buses Operated More than 25,000 h

This study investigates the performance losses and degradation of proton-exchange-membrane fuel-cell stacks taken from the Alameda Contra Costa Transit District (AC Transit) bus system (Alameda and Contra Costa counties, California, United States) that were operated for over 25,000 h. Here, we focus on the origin of differences in electrochemical performance between beginning-of-life (BOL) and end-of-life states as well as diagnostic data acquired during the lifetime of the buses. In doing so, we employ in- and ex- situ characterization methods such as polarization curves, electrochemical impedance spectroscopy, electron microscopy, and X-ray characterization. Uniform degradation of the catalyst layer including Pt agglomeration/migration and electrode thinning was observed in all of the post-teardown measurements compared to BOL materials resulting from years of field operation. Despite these changes, the measured post-teardown performance suggests a sufficient output for the expected load, which indicate factors other than degradation of the membrane-electrode assemblies (MEAs) are likely responsible for the decommissioning of the stacks. The findings indicate that these MEA materials can enable long lifetime in fuel-cell vehicles, if the MEAs are not subjected to adverse operating conditions. The results also highlight the need for more in-vehicle diagnostics to maximize the lifetime of fuel cell vehicle (FCV) powerplants.

25 ENERGY STORAGE↗
DOE OSTI2023

Reaction nanoscopy of ion emission from sub-wavelength propanediol droplets

Abstract Droplets provide unique opportunities for the investigation of laser-induced surface chemistry. Chemical reactions on the surface of charged droplets are ubiquitous in nature and can provide critical insight into more efficient processes for industrial chemical production. Here, we demonstrate the application of the reaction nanoscopy technique to strong-field ionized nanodroplets of propanediol (PDO). The technique’s sensitivity to the near-field around the droplet allows for the in-situ characterization of the average droplet size and charge. The use of ultrashort laser pulses enables control of the amount of surface charge by the laser intensity. Moreover, we demonstrate the surface chemical sensitivity of reaction nanoscopy by comparing droplets of the isomers 1,2-PDO and 1,3-PDO in their ion emission and fragmentation channels. Referencing the ion yields to gas-phase data, we find an enhanced production of methyl cations from droplets of the 1,2-PDO isomer. Density functional theory simulations support that this enhancement is due to the alignment of 1,2-PDO molecules on the surface. The results pave the way towards spatio-temporal observations of charge dynamics and surface reactions on droplets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Imaging, understanding, and control of nanoscale materials transformations

The development of liquid cells for transmission electron microscopy has enabled breakthroughs in our ability to follow nanoscale structural, morphological, or chemical changes during materials growth and applications. Time-resolved high-resolution imaging and chemical analysis through liquids opened the opportunity to capture nanoscale dynamic processes of materials, including reaction intermediates and the transformation pathways. In this article, a series of work is highlighted with topics ranging from liquid cell developments to in situ studies of nanocrystal growth and transformations, dendrite formation, and suppression of lithium dendrites through in situ characterization of the solid–electrolyte interphase chemistry. The understanding garnered is expected to accelerate the discovery of novel materials for applications in energy storage, catalysis, sensors, and other functional devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

LTE-P-10 RDE

A standardized procedure for rotating disk electrode (RDE) experiments for the ex-situ characterization of oxygen evolution reaction (OER) catalysts for PEM water electrolyzers. This protocol should allow for the analysis of onset potential, overpotential at a fixed current, catalytic activity, and electrochemical surface area of these catalysts.

08 HYDROGEN↗
DOE OSTI2020

Low temperature, ambient pressure electrochemical ammonia synthesis in alkaline media — Mechanistic studies and catalyst design. Final Report

Ammonia synthesis via the Haber-Bosch process is a pillar of modern agriculture, which converts the abundant but inert dinitrogen in the atmosphere to nitrogen-based fertilizers. Despite more than a century of optimization, the Haber-Bosch process remains energy intensive and reliant on fossil fuels and produces large amounts of CO 2 . Distributed and modular ammonia synthesis via the electrochemical nitrogen reduction reaction (ENRR) at or close to ambient conditions, powered by renewable electricity is an attractive alternative because it allows as needed production of ammonia, and in turn fertilizers. However, selective ENRR catalysts remain lacking. In this project, we systematically investigated two categories of catalytic materials, i.e., precious metals and transition metal nitrides, in the ENRR. Precious metals exhibit low activity and selectivity in the ENRR, which is in agreement with recent computational studies. Transition metal nitrides, especially VN, has been demonstrated as active and selective ENRR catalysts. We developed the first quantitative method to determine the amount of ammonia produced in the ENRR on N-containing containing catalysts in the membrane electrode assembly configuration. An initial ammonia production rate of 6.6 × 10 -10 mol s -1 mg -1 and a Faradaic efficiency of 6.0% at -0.1 V were reached on VN. After the initial deactivation, VN was shown to be stable in the ENRR for 116 hours with a steady state ammonia production rate of 1.1 × 10 -10 mol s -1 cm -2 . A vanadium oxynitride species was identified as the active phase in the ENRR via a combination of operando and ex situ characterization techniques. In addition, we established that the ENRR proceeded on transition metal nitrides via the Mars van Krevelen mechanism and determined the initial and steady state active site densities by developing a quantitative isotopic exchange method.

42 ENGINEERING↗
DOE OSTI2021

Collective Summary of sCO2 Materials Development (Supercritical Transformational Electric Power Generation (STEP) Level 2 Milestone Report) (Parts I - II)

Polymers such as PTFE (polytetrafluorethylene or Teflon), EPDM (ethylene propylene diene monomer) rubber, FKM fluoroelastomer (Viton), Nylon 11, Nitrile butadiene (NBR) rubber, hydrogenated nitrile rubber (HNBR) and perfluoroelastomers (FF_202) are commonly employed in super critical CO 2 (sCO2) energy conversion systems. O-rings and gaskets made from these polymers face stringent performance conditions such as elevated temperatures, high pressures, pollutants, and corrosive humid environments. In FY 2019, we conducted experiments at high temperatures (100°C and 120°C) under isobaric conditions (20 MPa). Findings showed that elevated temperatures accelerated degradation of polymers in sCO2, and that certain polymer microstructures are more susceptible to degradation over others. In FY 2020, the focus was to understand the effect of sCO2 on polymers at low (10 MPa) and high pressures (40 MPa) under isothermal conditions (100°C). It was clear that the same selectivity was observed in these experiments wherein certain polymeric functionalities showed more propensity to failure over others. Fast diffusion, supported by higher pressures and long exposure times (1000 hours) at the test temperature, caused increased damage in sCO2 environments to even the most robust polymers. We also looked at polymers under compression in sCO2 at 100°C and 20 MPa pressure to imitate actual sealing performance required of these materials in sCO2 systems. Compression worsened the physical damage that resulted from chemical attack of the polymers under these test conditions. In FY 2021, the effect of cycling temperature (from 50°C to 150°C to 50°C) for polymers under a steady sCO2 pressure of 20 MPa was studied. The aim was to understand the influence of cycling temperatures of sCO2 for typical polymers under isobaric (20 MPa) conditions. Thermoplastic polymers (Nylon, and PTFE) and elastomers (EPDM, Viton, Buna N, Neoprene, FF202, and HNBR) were subjected to 20 MPa sCO2 pressure for 50 cycles and 100 cycles in separate experiments. Samples were extracted for ex-situ characterization at 50 cycles and upon the completion of 100 cycles. Each cycle constituted of 175 minutes of cycling from 50°C to 150°C. The polymer samples were examined for physical and chemical changes by Dynamic Mechanical and Thermal Analysis (DMTA), Fourier Transform Infrared (FTIR) spectroscopy, and compression set. Density and mass changes immediately after removal from test were measured for degree of swell comparisons. Optical microscopy techniques and micro computer tomography (micro CT) images were collected on select specimens. Evaluations conducted showed that exposures to super-critical CO2 environments resulted in combinations of physical and/or chemical changes. For each polymer, the dominance of cycling temperatures under sCO2 pressures, were evaluated. Attempts were made to qualitatively link the permanent sCO2 effects to polymer micro- structure, free volume, backbone substitutions, presence of polar groups, and degree of crystallinity differences. This study has established that soft polymeric materials are conducive to failure in sCO2 through mechanisms of failure that are dependent on polymer microstructure and chemistry. Polar pendant groups, large atom substitutions on the backbone are some of the factors that are influential structural factors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

VTO battery project FY2022 Q2 (Quarterly Report)

The project has two primary objectives: (1) down select three-dimensional (3D) printing and post-processing approaches for SSE/cathode integration, and (2) understand battery failure mechanisms via ex situ and in situ characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Programming Function via Soft Materials (PFvSM) (Final Report)

The PFvSM cluster at the University of Illinois greatly deepened the science of soft materials and expanded the means for embedding within them unprecedented functionalities. We pioneered a mesoscopic approach to materials design that combined leading competencies in fundamental experimental and theoretical soft matter science and fabrication that powerfully establishes equilibrium and nonequilibrium assembly of novel and complex building blocks as a preeminent contributor to progress in materials chemistry. Our cluster’s vision was an integrated program of work centered on soft matter science with the ultimate goal of impacting important energy technologies. As elementary units we employed function-encoded colloids, nanoparticles, large mesh fibrillar gels, deterministically fabricated networks and hybrid objects. These materials were employed as building blocks for diverse model systems that allowed fundamental soft matter principles of wide relevance to be established. Their assembly into materials with useful functional behavior provided new approaches to challenging problems in basic energy science including energy harvesting, transport and storage. To achieve these goals the cluster brought together a team of recognized world-leaders in materials synthesis and processing, in-situ characterization, theory and modeling, and materials design, integration and fabrication

36 MATERIALS SCIENCE↗
DOE OSTI2022

VTO FY2022 Q3 (Quarterly Report)

The project has two primary objectives: (1) down select three-dimensional (3D) printing and post-processing approaches for SSE/cathode integration, and (2) understand battery failure mechanisms via ex situ and in situ characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Predicting and Controlling Corrosion (Abbreviated Final Report)

Corrosion accumulates significant replacement costs in the transportation, utility, manufacturing, and infrastructure sectors. It also underpins several of LLNL’s core missions in stockpile stewardship, defense, and energy security. Whereas most corrosion and aging models are empirically parameterized to describe well-defined conditions late in the reaction, the factors that determine the early stages of corrosion—during which mitigation could be most impactful— are poorly understood. This project addressed the critical need for new approaches to predict the kinetics of corrosion initiation based on firm physical and chemical understanding. The activities encompassed degradation of relevant metals in both hydrogen-rich and environmental corrosion scenarios. The team integrated state-of-the-art multiscale simulation, in situ characterization, and data science within three technical thrusts: hydriding of Ti alloys; aqueous corrosion of Al and Ni-Cr alloys; and degradation of additively manufactured 316L stainless steel. In each case, novel capabilities were developed to identify and track the impacts of key atomistic, compositional, and microstructural features on the metal systems. For hydriding, protocols were developed to tightly integrate multiscale models, advanced multimodal characterization, and machine learning to determine how hydrogen interacts with native passivating surface oxides and nucleates new undesired phases, shedding new light on the critical role of grain boundaries, interfaces, and atomically disordered regions. For aqueous corrosion, the project demonstrated methods to predict dissolution rates of metal surfaces in corrosive solutions, to measure and understand microstructural and grain orientation effects on corrosion susceptibility, and to investigate competing growth and dissolution kinetics of surface oxides. For additively manufactured metals, analysis using state-of-the-art microscopy techniques revealed the role of specific heterogeneities invoked during laser processing, including cellular structure, dislocations, and precipitates, on corrosion susceptibility. In addition to new capabilities and understanding, the project provided an avenue for workforce development, as well as key partnerships with stakeholders in corrosion science.

08 HYDROGEN↗
DOE OSTI2022

Vehicle Technology Office Battery Project (FY22Q4 Quarterly Report)

The project has two primary objectives: (1) down select three-dimensional (3D) printing and post-processing approaches for solid-state electrolyte (SSE) / cathode integration, and (2) understand battery failure mechanisms via ex situ and in situ characterization.

25 ENERGY STORAGE↗
DOE OSTI2023

Vehicle Technology Office Battery Project (FY23Q1 Quarterly Report)

The project has two primary objectives: (1) down select three-dimensional (3D) printing and post-processing approaches for solid-state electrolyte (SSE) / cathode integration, and (2) understand battery failure mechanisms via ex situ and in situ characterization.

25 ENERGY STORAGE↗
DOE OSTI2024

How is Rational Design of Electrocatalysts Crucial for Maximizing CO2 Electroreduction Performance?

The invited talk "How is Rational Design of Electrocatalysts Crucial for Maximizing CO2 Electroreduction Performance?” was presented in the symposium "Electrocatalysis for Sustainable Energy and Biomass Conversion: Fundamentals, Applications, and Perspectives”, Division of Catalysis Science and Technology, 2024 ACS Fall Meeting. The presentation briefly introduces NETL facilities and our Electrochemical Carbon Conversion portfolio to audiences. The talk primarily discusses how the geometry and surface composition of copper- and tin-based electrocatalysts would maximize the CO2 conversion to sustainable, carbon-neutral gas and liquid products in different device configurations. Ex situ and in situ characterization results are additionally discussed to correlate the structural, physico-chemical, and electronic properties with CO2 reduction activity and selectivity.

Nguyen Phan, Thuy Duong↗