SEARCH · Search NASA

Results for “Injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Fabrication of sinterable silicon nitride by injection molding

Transformation of structural ceramics from the laboratory to production requires development of near net shape fabrication techniques which minimize finish grinding. One potential technique for producing large quantities of complex-shaped parts at a low cost, and microstructure of sintered silicon nitride fabricated by injection molding is discussed and compared to data generated from isostatically dry-pressed material. Binder selection methodology, compounding of ceramic and binder components, injection molding techniques, and problems in binder removal are discussed. Strength, oxidation resistance, and microstructure of sintered silicon nitride fabricated by injection molding is discussed and compared to data generated from isostatically dry-pressed material.

Quackenbush, C. L.↗

NASA NTRS1982

Catalytic combustion with steam injection

The effects of steam injection on (1) catalytic combustion performance, and (2) the tendency of residual fuel to burn in the premixing duct upstream of the catalytic reactor were determined. A petroleum residual, no. 2 diesel, and a blend of middle and heavy distillate coal derived fuels were tested. Fuel and steam were injected together into the preheated airflow entering a 12 cm diameter catalytic combustion test section. The inlet air velocity and pressure were constant at 10 m/s and 600 kPa, respectively. Steam flow rates were varied from 24 percent to 52 percent of the air flow rate. The resulting steam air mixture temperatures varied from 630 to 740 K. Combustion temperatures were in the range of 1200 to 1400 K. The steam had little effect on combustion efficiency or emissions. It was concluded that the steam acts as a diluent which has no adverse effect on catalytic combustion performance for no. 2 diesel and coal derived liquid fuels. Tests with the residual fuel showed that upstream burning could be eliminated with steam injection rates greater than 30 percent of the air flow rate, but inlet mixture temperatures were too low to permit stable catalytic combustion of this fuel.

Anderson, D. N.↗

NASA NTRS1983

Comparative evaluation of gas-turbine engine combustion chamber starting and stalling characteristics for mechanical and air-injection

The effectiveness of propellant atomization with and without air injection in the combustion chamber nozzle of a gas turbine engine is studied. Test show that the startup and burning performance of these combustion chambers can be improved by using an injection during the mechanical propellant atomization process. It is shown that the operational range of combustion chambers can be extended to poorer propellant mixtures by combined air injection mechanical atomization of the propellant.

Dyatlov, I. N.↗

NASA NTRS1981

Investigations of stability and dynamic performances of switching regulators employing current-injected control

The stability and dynamic performances of a buck/boost regulator employing a current-injected control are examined. Small-signal models for the power state, the multi-loop error processor and the duty-cycle pulse-modulator are developed. The error-processor model which incorporates the current-injected loop, the dc loop and the compensation network permits evaluation of the effects of each individual control loop and their combined efforts toward shaping the performance characteristics of the closed-loop system. Comparisons are made between this modeling approach and earlier approaches. Some important yet subtle dissimilarities are discussed. This model predicts the constant-frequency 50 percent duty-cycle instability which is inherent to the current-injected control.

Lee, F. C.↗

NASA NTRS1982

Laboratory simulation of injection particle beams in the ionosphere

A series of experiments were carried out in large vacuum chambers in an attempt to understand the physics of the beam injection experiments. In the experiments, the electron beam was injected into an initially neutral gas. A plasma then accumulated as a result of ionization of the gas by the electron beam. The long interaction length and the longitudinal magnetic field resulted in the accumulation plasma densities considerably greater than the beam density. The most significant experimental result is that electron beams in the low keV energy range can ignite the beam plasma discharge (BPD) when their perveance is greater than 5 x 10 to the -7th AV exp -3/2, for pressures typical of the ionosphere. Ignition of the BPD may provide an explanation for many of the puzzling results observed in flight injection experiments.

Kellogg, P. J.↗

NASA NTRS1984

An investigation into the injection molding of PMR-15 polyimide

The chemorheological behavior of the PRM-15 molding compounds were characterized, the range of suitable processing parameters for injection molding in a reciprocating screw injection molding machine was determined, and the effects of the injection molding processing parameters on the mechanical properties of molded PMR-15 parts were studied. The apparatus and procedures for measuring viscosity and for determining the physical response of the material during heating are described. Results show that capillary rheometry can be effectively used with thermosets if the equipment is designed to overcome some of the inherent problems of these materials. A uniform temperature was provided in the barrel by using a circulating hot oil system. Standard capillary rheometry methods can provide the dependence of thermoset apparent viscosity on shear rate, temperature, and time. Process conditions resulting in complete imidization should be carefully defined. Specification of controlled oven temperature is inadequate and can result in incomplete imidization. For completely imidized PMR-15 heat at 15 C/min melt flow without gas evolution occurs in the temperature range of 325 C to 400 C.

Colaluca, M. A.↗

NASA NTRS1983

Dynamical injections as the source of near geostationary quiet time particle spatial boundaries

The question whether the noon-dusk feature is a manifestation of the spatial structures that should arise from quasi-stationary convection is examined. The key consideration here is whether the energy dispersion of the feature can be explained. It is shown that the observed energy dispersion cannot be attributed to the standard stationary convection configurations, either perturbed or unperturbed. It is also demonstrated, using a detailed computer simulation, that the nighttime, double-spiral-shaped injection boundary (used previously to reproduce the fast changing nighttime features) is successful at reproducing the noon-dusk feature by allowing the particles to evolve for periods of 12 to 36 hours after the injection. It is stressed that the portion of the injection boundary responsible for the feature looks very different from the standard convection boundaries configuration. Conclusions are offered concerning the importance of quasi-stationary convection as the mechanism by which the near geostationary regions are populated.

Mauk, B. H.↗

NASA NTRS1985

Flow visualization study of the effect of injection hole geometry on an inclined jet in crossflow

A flow visualization was studied by using neutrally buoyant, helium-filled soap bubbles, to determine the effect of injection hole geometry on the trajectory of an air jet in a crossflow and to investigate the mechanisms involved in jet deflection. Experimental variables were the blowing rate, and the injection hole geometry cusp facing upstream (CUS), cusp facing downstream (CDS), round, swirl passage, and oblong. It is indicated that jet deflection is governed by both the pressure drag forces and the entrainment of free-stream fluid into the jet flow. For injection hole geometries with similar cross-sectional areas and similar mass flow rates, the jet configuration with the larger aspect ratio experienced a greater deflection. Entrainment arises from lateral shearing forces on the sides of the jet, which set up a dual vortex motion within the jet and thereby cause some of the main-stream fluid momentum to be swept into the jet flow. This additional momentum forces the jet nearer the surface. Of the jet configurations, the oblong, CDS, and CUS configutations exhibited the largest deflections. The results correlate well with film cooling effectiveness data, which suggests a need to determine the jet exit configuration of optimum aspect ratio to provide maximum film cooling effectiveness.

Simon, F. F.↗

NASA NTRS1985

Characteristics of heat exchange in the region of injection into a supersonic high-temperature flow

An experimental investigation of the local heat transfer coefficient distribution during gas injection into the supersonic-flow portion of a Laval nozzle is discussed. The controlling dimensionless parameters of the investigated process are presented in terms of a generalized relation for the maximum value of the heat transfer coefficient in the nozzle cross section behind the injection hole. Data on the heat transfer coefficient variation along the nozzle length as a function of gas injection rate are also presented, along with the heat transfer coefficient distribution over a cross section of the nozzle.

Bakirov, F. G.↗

NASA NTRS1984

Tunable mode and line selection by injection in a TEA CO2 laser

Tunable mode selection by injection in pulsed CO2 lasers is examined, and both analytical and numerical models are used to compute the required injection power for a variety of experimental cases. These are treated in two categories: mode selection at a desired frequency displacement from the center frequency of a transition line in a dispersive cavity and mode (and line) selection at the center frequency of a selected transition line in a nondispersive cavity. The results point out the potential flexibility of pulsed injection in providing wavelength tunable high-energy single-frequency pulses.

Menzies, R. T.↗

NASA NTRS1985

Mixing layer control for tangential slot injection in turbulent flows

Tangential injection into turbulent flows is one of the most promising methods of minimizing skin friction and providing thermal protection. The technique also has application to laser hardening. The effectiveness of the injected material can be increased if the spreading rate of the resulting mixing region can be reduced. Various techniques which have been shown to be effective in manipulating the rate of growth of mixing layers under certain conditions have been applied to a slot configuration having a thick external turbulent boundary layer. These include geometry modifications to the slot lip trailing edge and acoustic excitation of the slot exit plane over a wide range of frequencies. Neither of these approaches produced any noticeable effect on the downstream evolution of the mixing layer. This lack of effectiveness is attributed to the dominating influence of the well-developed incoming turbulent boundary layer. The placement of large-eddy breakup devices in this boundary layer upstream of the injection point did produce significantly lower velocities in the near-wall region of the flow downstream of the slot exit.

Mcinville, R. M.↗

NASA NTRS1986

Measurements of a single lateral jet injected into swirling crossflow

Experiments have been conducted to document the time-mean and turbulent flowfield of a deflected turbulent jet in a confined swirling crossflow. The jet-to-crossflow velocity ratio of 4 was investigated with swirler vane angles of 45 and 70 degrees. A six-orientation single hot-wire technique was used to measure the velocities and turbulence properties of the flow. In addition, a five-hole pitot probe technique was used to measure the time-mean velocities or verification purposes. The results are presented in the form of r-x plots to aid visualization of the fully three-dimensional flowfield. The swirl in the crossflow intensified the local velocity at the location of the injected jet, which effectively reduced the jet-to-crossflow velocity ratio. This caused the trajectory of the injected jet to follow the path of the local flow direction of the crossflow, and reduce its penetration into the crossflow. The time-mean velocity measurements using the hot-wire corresponded to pitot-probe data obtained in identical flow conditions. Turbulence stress data show the same trends as previous swirl flow data without lateral injection. The lateral jet was found to deflect the axis of the precessing vortex core.

Ong, L. H.↗

NASA NTRS1985

Competing atomic processes in Ba and Sr injection critical velocity experiments

The critical ionization velocity effect requires a superthermal electron population to ionize through collisional impact. Such superthermal electrons can however lose energy to competing atomic processes, as well as to ionization, thus limiting the efficiency of the effect. Considering Ba and Sr magnetospheric injection experiments designed to test the CIV theory, it is found that in both cases roughly 60 percent of the superthermal electron energy is lost on exciting line radiation. Moreover, energy loss to background neutral oxygen places a strict limit on the injected cloud densities for which critical velocity effects are possible; a finding which explains the consistently negative results in radial injection experiments.

Newell, P. T.↗

NASA NTRS1985

Processing study of injection molding of silicon nitride for engine applications

The high hardness of silicon nitride, which is currently under consideration as a structural material for such hot engine components as turbine blades, renders machining of the material prohibitively costly; the near net shape forming technique of injection molding is accordingly favored as a means for component fabrication. Attention is presently given to the relationships between injection molding processing parameters and the resulting microstructural and mechanical properties of the resulting engine parts. An experimental program has been conducted under NASA sponsorship which tests the quality of injection molded bars of silicon nitride at various stages of processing.

Rorabaugh, M. E.↗

NASA NTRS1986

Gas ionization induced by a high speed plasma injection in space

Gas ionization induced by a fast plasma injection has been observed with the Space Experiments with Particle Accelerators (SEPAC) Experiment on Spacelab-1. When an impulsive high-density plasma was injected from the orbiter, waves near the lower-hybrid frequency were enhanced, and the surrounding gas drifting with the orbiter was ionized for several tens of milliseconds after the plasma injection. The long-duration gas ionization was observed only when the plasma flux incoming to the orbiter cargo bay and the orbital velocity perpendicular to the magnetic field were relatively large. This effect has been explained by the concept of critical velocity ionization (CVI) for the gas drifting with the orbiter, although the gas velocity perpendicular to the magnetic field was less than the Alfven critical velocity.

Sasaki, S.↗

NASA NTRS1985

An enhancement of plasma density by neutral gas injection observed in SEPAC Spacelab-1 experiment

An enhancement of plasma density observed during a neutral gas injection in Space Experiments with Particle Accelerators by the Space Shuttle/Spacelab-1 is presented. When a plume of nitrogen gas was injected from the orbiter into space, a large amount of plasma was detected by an onboard plasma probe. The observed density often increased beyond the background plasma density and was strongly dependent on the attitude of the orbiter with respect to the velocity vector. This effect has been explained by a collisional interaction between the injected gas molecules and the ionospheric ions relatively drifting at the orbital speed.

Sasaki, S.↗

NASA NTRS1987

User's guide to programming fault injection and data acquisition in the SIFT environment

Described are the features, command language, and functional design of the SIFT (Software Implemented Fault Tolerance) fault injection and data acquisition interface software. The document is also intended to assist and guide the SIFT user in defining, developing, and executing SIFT fault injection experiments and the subsequent collection and reduction of that fault injection data. It is also intended to be used in conjunction with the SIFT User's Guide (NASA Technical Memorandum 86289) for reference to SIFT system commands, procedures and functions, and overall guidance in SIFT system programming.

Elks, Carl R.↗

NASA NTRS1986

Pulsed injection control of a titanium-doped sapphire laser

Injection control of a tunable Ti:sapphire laser using a narrow-bandwidth pulsed dye laser operating at a wavelength removed from the peak of the Ti:sapphire-laser gain curve is reported. The free-running Ti:sapphire laser had broadband laser emission from 750 to 790 nm. Injection at 727 nm resulted in essentially complete energy extraction at that wavelength in a 2.5-pm bandwidth matching the injection source.

Brockman, Philip↗