Search NASA⌕ Search

SEARCH · Search NASA

Results for “LPBF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured Alloys in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in elevated temperature and pressure direct-fired supercritical CO2 (sCO2) power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can have additional corrosion effects than found at ambient pressure conditions. Several wrought nickel-based commercial alloys (230, 263, 282, 617, 625, 740H) were exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure (0.1 MPa) and supercritical conditions (20 MPa) for over 2,000 h. Additionally, additive manufactured (AM) 282 produced by laser powder bed fusion (LPBF) were also included in the exposures. Supercritical conditions affected the oxidation behavior of several alloys. Most notably, water-vapor assisted Cr-oxide volatilization was observed at 750 °C supercritical conditions. Many alloys did not form sufficient protective Cr-oxide scales at supercritical conditions, leading to increased oxidation at elevated pressure. Differences in oxidation behavior were also observed for 282 AM samples compared to their wrought counterparts, with the differences also dependent on the LPBF build parameters and post-production treatments (heat treatment and surface finishing procedures). The AM samples formed Mo-rich carbides in the alloy beneath the oxide following sCO2 exposure, implying potentially higher levels of carbon uptake relative to the wrought

Carney, Casey↗
DOE OSTI2023

Irradiation and corrosion testing of laser powder bed fusion-manufactured materials in the AMMT program

The Advanced Materials and Manufacturing Technologies (AMMT) program operating under the Department of Energy Office of Nuclear Energy is accelerating the qualification and deployment of additively manufactured materials in advanced reactor environments. Laser powder bed fusion (LPBF) has emerged as a promising additive manufacturing technique to fabricate complex components with the potential of tailored material properties. In the nuclear industry, metal additive manufacturing can offer numerous advantages, such as reduced lead times, streamlined quality assurance, and cost-effective low-volume production of new and replacement components with conventional or novel materials and geometries. The rapid and effective qualification of the effect of processing variability on the performance and degradation of additively manufactured materials is essential for the deployment of these components into advanced reactor environments. As part of this effort, AMMT is performing irradiation and corrosion testing of several materials built by LPBF, including 316L and 316H stainless steels. Our efforts encompass neutron irradiation testing, ion irradiation testing, and advanced modeling to provide a robust technical basis for understanding the effect of process variability on materials degradation and developing a sound methodology for accelerated ion irradiation testing. We develop focused irradiation test plans that align well with risk-informed and technologically inclusive approaches to licensing. We will also discuss our plans and specific concerns for corrosion testing additively manufactured material, with a primary focus on molten salt and liquid sodium environments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Environmental Degradation in Advanced Reactor Environments

The Advanced Materials and Manufacturing Technologies (AMMT) program operating under the Department of Energy Office of Nuclear Energy is accelerating the qualification and deployment of additively manufactured materials in advanced reactor environments. Laser powder bed fusion (LPBF) has emerged as a promising additive manufacturing technique to fabricate complex components with the potential of tailored material properties. In the nuclear industry, metal additive manufacturing can offer numerous advantages, such as reduced lead times, streamlined quality assurance, and cost-effective low-volume production of new and replacement components with conventional or novel materials and geometries. The rapid and effective qualification of the effect of processing variability on the performance and degradation of additively manufactured materials is essential for the deployment of these components into advanced reactor environments. This talk presents an overview of the Environmental Effects area activities within AMMT. AMMT is performing irradiation and corrosion testing of several materials built by LPBF, including 316L and 316H stainless steels. Our irradiation efforts encompass neutron irradiation testing and ion irradiation testing to provide a robust technical basis for understanding the effect of process variability on materials degradation. We develop focused irradiation test plans that align well with risk-informed and technologically inclusive approaches to licensing. We will also discuss our plans and specific concerns for corrosion testing additively manufactured material, with a primary focus on molten salt and liquid sodium environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Progress and Challenges of Additive Manufacturing of Tungsten and Alloys as Plasma-Facing Materials

Tungsten (W) and W alloys are considered as primary candidates for plasma-facing components (PFCs) that must perform in severe environments in terms of temperature, neutron fluxes, plasma effects, and irradiation bombardment. These materials are notoriously difficult to produce using additive manufacturing (AM) methods due to issues inherent to these techniques. The progress on applying AM techniques to W-based PFC applications is reviewed and the technical issues in selected manufacturing methods are discussed in this review. Specifically, we focus on the recent development and applications of laser powder bed fusion (LPBF), electron beam melting (EBM), and direct energy deposition (DED) in W materials due to their abilities to preserve the properties of W as potential PFCs. Additionally, the existing literature on irradiation effects on W and W alloys is surveyed, with possible solutions to those issues therein addressed. Finally, the gaps in possible future research on additively manufactured W are identified and outlined.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Powder Bed Fusion Laser Beam Metals Additive Manufacturing: Process Monitoring Approaches for Qualification and Certification

The use of in-situ process monitoring is of interest to lower the cost of inspection for the qualification of powder bed fusion laser beam metal (PBF-LB/M) additively manufactured (AM) parts. Precise monitoring of the PBF-LB/M AM build process constitutes a multi-scale and multi-discipline task. There are several significant challenges to the in-situ approach: the synchronization of sensor signals to process steps; the physical interpretation and classification of sensor signals; managing very large datasets; and comparing the inputs with the observed monitoring signals. At NASA Langley Research Center, a configurable architecture additive testbed has been developed to monitor the build process with synchronized sensors. The philosophy and method adopted for the synchronization of the cameras with laser power and position throughout a complex PBF-LB/M AM build will be described. The synchronized in-situ monitoring signals are compared with ex-situ nondestructive inspection, x-ray computed tomography (XCT). Such comparisons permit a better understanding of how the sequential process actions of LPBF-AM can affect build quality. The multi-scale and complex process of printing additively manufactured (AM) parts can have unexpected, but predictable, build conditions that result in material microstructure variability. This presentation will describe an additive manufacturing model-based process metric (AM-PM) computational method that is a fully parallel reduced order modeling approach developed to evaluate the evolution of AM processes. This method couples the known sequence of the AM process with a physically informed nearest neighbors’ calculation to map the conditions of a part-scale build. The result is a map of the build that is derived directly from build files or in-situ process monitoring sensors. The methodology of the approach will be described and mapped to the porosity observed from XCT for a complex PBF-LB/M build. Such comparative results develop understanding of how the sequential process actions can affect the PBF-LB/M AM build quality and microstructure variability.

Laser Powder Bed Fusion↗
DOE OSTI2020

Microstructure–Property Correlation in a Laser Powder Bed Fusion Processed High-Strength AF-9628 Steel

Laser powder bed fusion additive manufacturing (LPBF-AM) of a low-alloy, high-performance AF-9628 steel results in exceptionally high strength and good ductility. The reasons for such mechanical properties are investigated through detailed microscopy performed at several length scales. Thus, the characterization of melt pool, porosity, grain morphology, phases, and dislocations is performed in the as-printed material. The as-printed material consists of only 0.004 vol% of uniformly distributed porosity, single-phase martensitic laths with an average lath size of ≈2.5 μm, the absence of carbides indicating interstitial trapping of C atom, and high dislocation density in the martensitic laths. Experimental data through microscopy are then fed in analytical models for calculating strengthening contributions from various strengthening mechanisms. Calculated yield strength agrees well with experimentally determined value, and therefore, activation of various strengthening mechanisms is established in as-printed AF-9628.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A combination interferometric and morphological image processing approach to rapid quality assessment of additively manufactured cellular truss core components

Advanced manufacturing (AM) processes such as laser powder bed fusion (LPBF) are increasingly capable of fabricating components with useful and unprecedented mechanical properties by incorporating complex internal bracing structures. From the standpoint of quality control and assessment, however, internally complex assemblies present significant build-verification challenges. Here we propose a hybrid approach to the inspection involving the application of computer-aided speckle interferometry (CASI) and morphological image processing as a rapid, inexpensive, and facile method for AM quality control. The described methodology has low capital equipment costs, is full-field and non-contact, can be used in an industrial setting, and has very low requirements in terms of operator training and expertise. Consisting primarily of the combination of image processing software with a simple optical system of variable sensitivity, the method is shown to be effective for inspection of a titanium honeycomb component subjected to differential pressure. Results are compared to those achieved with computed tomography (CT), immersion ultrasound testing (UT), and optical holographic interferometry. Here we propose several possible processing strategies for automated quality assessment based on this powerful hybrid approach.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Melt Pool and Heat Treatment Optimization for the Fabrication of High-Strength and High-Toughness Additively Manufactured 4340 Steel

Additively manufactured (AM) components offer superior design flexibility compared to their conventionally manufactured counterparts, and optimizing processing parameters is key to achieving high-quality depositions with desirable and predictable mechanical properties. This study was focused on 4340 steel fabricated using laser powder bed fusion (LPBF), and 42 laser power and scan speed combinations have been systematically investigated to determine an optimized melt pool geometry that would ensure fully-dense parts. The AM material was compared with a wrought 4340 equivalent and studied in two customized heat treated conditions, optimized for strength and toughness, respectively. The microstructures of the as-fabricated and heat treated AM and wrought materials were characterized to assess differences introduced by the layer-by-layer fabrication process and subsequent heat treatment. Tensile properties of both materials were also evaluated and demonstrate that the AM materials offer equal or superior properties compared to the wrought equivalents. Differences in fracture surface morphologies indicate the distinct failure mechanisms associated with the materials’ characteristic microstructures, and the role of inclusions in the failures was studied to elucidate these differences. Complementary to the experimental investigations, the dataset was leveraged to make recommendations for future design of experiments to optimize AM build parameters in other material systems. A statistical Monte Carlo analysis was used to predict the interpolation error produced using reduced datasets and to enable informed processing parameters selection. These findings are discussed to make recommendations for the use of AM materials for high-integrity structural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Leveraging Solute Segregation in Laser Powder Bed Fusion to Achieve Superior Strength and Ductility Via Single-Step Heat Treatment in Ti-Free Grade 300 Maraging Steel

Maraging steels are Fe-Ni precipitation-strengthened steels that can be heat treated for achieving high strength with an accompanying loss in ductility, a trend common to most metals. Here, we show that the segregation of Ni during laser powder bed fusion, commonly considered a nuisance that is dealt with via solutionizing heat treatments, can be leveraged via direct aging to achieve higher strength and ductility simultaneously, compared to a solutionized and aged condition. The high dislocation density in combination with solute segregation in the as-fabricated material promotes the precipitation of Mo-rich intermetallic phases that are responsible for the high strength, and the Ni segregated regions facilitate austenite reversion during direct aging. The reverted austenite enhances the elongation via transformation-induced plasticity. While overcoming the strength–ductility conundrum, direct aging can significantly reduce the energy and emissions associated with multistep heat treatments, especially in the global tool and die industry, while laser powder bed fusion (LPBF) can enable tools with integrated cooling channels for increased downstream production efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AFRL Additive Manufacturing Modeling Series: Challenge 1, Characterization of Residual Strain Distribution in Additively-Manufactured Metal Parts Using Energy-Dispersive Diffraction

A machine component fabricated by additive manufacturing (AM) of metal powders often possesses steep residual stress gradients with significant magnitudes due to large temperature gradients that transpire within a localized area during fabrication. These processing-induced residual stresses can cause distortion of the part, and if they are of significant magnitude, they could induce cracking of the component, degrade printability, and/or diminish subsequent mechanical performance. The ability to predict these residual stresses imparted by AM is an important step in permeating AM technology for advanced manufacturing. Calibration and validation of AM process models used for prediction are, therefore, a critical step in understanding the origin and mitigating the challenges associated with residual stresses inherent to the AM process. In the present work, the residual strain distributions in components with simple geometries fabricated by a laser powder bed fusion (LBPF) process were characterized non-destructively using energy-dispersive X-ray diffraction in support of the US Air Force Research Laboratory Additive Manufacturing Modeling Challenge Series Groeber et al. (JOM 70:441-448, 2018). The measurement setup and approach are described in detail so that the data can be used as a benchmark to calibrate and validate models for the prediction of macro-scale residual stresses due to the LPBF process.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Outcomes and Conclusions from the 2022 AM Bench Measurements, Challenge Problems, Modeling Submissions, and Conference

The Additive Manufacturing Benchmark Test Series (AM Bench) provides rigorous measurement data for validating additive manufacturing (AM) simulations for a broad range of AM technologies and material systems. AM Bench includes extensive in situ and ex situ measurements, simulation challenges for the AM modeling community, and a corresponding conference series. In 2022, the second round of AM Bench measurements, challenge problems, and conference were completed, focusing primarily upon laser powder bed fusion (LPBF) processing of metals, and both material extrusion processing and vat photopolymerization of polymers. In all, more than 100 people from 10 National Institute of Standards and Technology (NIST) divisions and 21 additional organizations were directly involved in the AM Bench 2022 measurements, data management, and conference organization. The international AM community submitted 138 sets of blind modeling simulations for comparison with the in situ and ex situ measurements, up from 46 submissions for the first round of AM Bench in 2018. Analysis of these submissions provides valuable insight into current AM modeling capabilities. The AM Bench data are permanently archived and freely accessible online. The AM Bench conference also hosted an embedded workshop on qualification and certification of AM materials and components.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-throughput surface characterization to identify porosity defects in additively manufactured 316L stainless steel

In the present study, a high throughput (HT) methodology is applied to rapidly assess the surface characteristics of 83 additively manufactured 316L stainless steel. The variation in surface roughness (S a ) showed a good correlation with a dimensionless number (π) and provided direct linkages to the internal porosity defects. Lack-of-fusion regime relates to high surface roughness (S a > 5 µm), low dimensionless number (π < 61), and the presence of cavities in between the melt pool tracks. Balling regime correlates to high surface roughness (S a > 5 µm), intermediate dimensionless number (61 < π < 146), and non-uniform melt pool track width. Keyhole regime shows low surface roughness (S a < 5 µm), high dimensionless number (π > 146), and a curved melt pool track. This approach accelerates the process parameter discovery and minimizes the porosity defects for the LPBF process. The impact of the defects on the as-processed tensile mechanical properties demonstrates that samples with porosity exhibit up to 10% less tensile strength and 30% less ductility than optimal samples.

316L stainless steel↗
DOE OSTI2021

Modelling the complex evaporated gas flow and its impact on particle spattering during laser powder bed fusion

The additive manufacturing (AM) of metals is becoming an increasingly important production process with the potential to replace traditional techniques such as casting. Laser Powder Bed Fusion (LPBF) is used in many applications to print metal parts from powder. The metal powder is heated locally with sufficient laser radiation that the liquid melt easily reaches its boiling temperature, which leads to a metallic vapour jet that can entrain both powder bed particles and molten droplets. The small size of laser-matter interaction site makes a detailed experimental analysis of the process challenging. Synchrotron X-ray imaging experiments are one of the few methods which can capture the dynamic melting and solidification processes. Comparing such experiments with computer simulations of the process is an important approach in order to better understand the manufacturing process and to analyse the influence of process parameters on the evaporated gas jet and the subsequent impact on particle ejection, leading to potentially reduced AM component quality. The melting and solidification of the metal powder is simulated using an Eulerian multiphase approach based on a control volume discretization of powder bed and substrate and a volume of liquid separation from melt and gas phase. The gas phase modelled as an ideal gas reaches velocities up to 100 m/s. Lagrangian particle tracking in the simulation demonstrates that the velocity fields calculated by the Eulerian multi-phase approach in combination with a standard drag-force model lead to particle accelerations in good agreement with those measured experimentally. In order to avoid numerical laborious Lagrangian calculations, a direct method to compare an Eulerian multiphase simulation with synchrotron X-ray experiments was introduced and validated. This approach is used to analyse the influence of process parameters including laser power and laser speed on the maximal acceleration of particles from the melt pool area. While the particle acceleration increases linearly with line energy in the conduction mode, a linear decrease of the acceleration with increasing line energy can be found in the transition mode before the accel-eration increases again with line energy in the keyhole mode.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Controlling melt flow by nanoparticles to eliminate surface wave induced surface fluctuation

The high surface roughness is one of the major challenges encountered in laser metal additive manufacturing (AM) processes, which is closely related to the melt flow behavior. However, how to control the melt flow in laser metal AM processes to improve surface finish is unknown. Here we reveal the effects of nanoparticles on melt flow behavior at every location of melt pool during laser metal AM process for the first time using Al6061 + TiC nanoparticles system and achieve significant improvement of surface finish by using TiC nanoparticles to control the melt flow and damp the surface wave. Based on the in-situ x-ray imaging observation, the surface wave is fully damped after adding TiC nanoparticles, compared with only 56% damping without nanoparticles during LPBF of Al6061. Our in-depth in-situ x-ray imaging analysis and viscosity measurement enable us to identify that nanoparticle-induced increase of viscosity causes the fully damping of the surface wave by (1) increasing the internal fluid friction for more efficient wave amplitude reduction, (2) controlling the melt flow to increase the surface wave number, (3) controlling the melt flow to increase the wave damping time. Furthermore, we also quantified the relative contributions of increasing fluid friction, increasing wave number, and increasing damping time to wave damping, which account for 61%, 25%, and 14%, respectively. Furthermore, our research provides the mechanisms and potential method to address the surface finish challenge in laser metal AM processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Anisotropic spall failure of additively manufactured 316L stainless steel

The dynamic high strain rate tensile (spall) failure of additively manufactured (AM) materials is an area of great interest but much less understood than material failure under other loading regimes. The research presented here examines the effects of microstructure anisotropy in 316L stainless steel fabricated by laser powder bed fusion (LPBF) on its spall failure and properties. In this work, plate-on-plate impact experiments were performed using an 80-mm gas gun to investigate the spall behavior of AM fabricated sample discs with impact along the perpendicular and parallel orientations relative to build directions. Experiments were also performed on wrought 316L stainless steel as baseline material with uniform equiaxed grain microstructure for comparison with the AM material of same composition. The spall experiments involved free-surface velocity profiles measured using Photon Doppler Velocimetry (PDV) to capture the spall pull-back signals, combined with post-mortem analysis of the microstructure of soft-recovered impacted samples. In the case of AM samples, spall failure initiated preferentially at melt pool boundaries in both impact directions. The spall plane location and spall strength, however, were both heavily influenced by the orientation of the impact direction relative to the build direction in the AM samples. The spall behavior is also observed to be more complex in the samples impacted perpendicular to the build (through-thickness) direction, due in large part to the orientation of the microstructural features such as melt pool boundaries, laser scan tracks, and general grain morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing enabled synergetic strengthening of bimodal reinforcing particles for aluminum matrix composites

An additive manufactured TiB 2 /Al-Cu-Mg-Ni composite with a minor amount of Sc was fabricated by laser powder bed fusion (LPBF). The composite shows a yield strength of ~370 MPa, almost doubling the strength of its wrought matrix counterpart, and an elongation of ~7 %. The superior mechanical properties are attributed to a unique micro-nano hierarchical microstructure, consisting of nanoscale and microscale TiB 2 particles dispersed in a matrix of fine aluminum grains (3 µm) together with intragranular intermetallic nanoparticles and nano-cellular networks (cell size 30 nm). The formation of the TiB 2 nanoparticles is the consequence of partial dissolution of the TiB 2 particulates and the enrichment of Sc in the newly formed nanoparticles. Remarkable strengthening effects are achieved by the bimodal TiB 2 particles, intermetallic nanoparticles and intragranular nano-cellular networks. Finally, this study provides new insights into the role of additive manufacturing in tailoring the microstructure of particulate reinforced metal matrix composites (MMCs) with advanced properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Grain structure and texture selection regimes in metal powder bed fusion

Additive manufacturing (AM) offers opportunities to produce complex part geometries not possible with conventional processing and in some cases even improve part performance. However, adoption has been slowed by difficulties assessing microstructure variability and there is no straightforward approach to relate processing to grain structure characteristics. In this study, datasets from AdditiveFOAM heat transport simulations of laser powder bed fusion (LPBF) are used to drive ExaCA simulations of grain structure. The GPU utilization of ExaCA and an algorithmic update for modeling melt pool overlap region solidification enabled rapid and parallel simulation across a wider range of process conditions than previously explored with cellular automata-based solidification models. A texture selection angle $θ_s$ is defined based on melt pool overlap geometry, and the range of $θ_s$ over which a commonly observed texture transition occurs in characterized AM builds was well-reproduced by ExaCA simulations over a wide range of melt pool shape, hatch spacing, and layer height. ExaCA simulations with 90 degree rotation of the scan direction on every other layer reproduced a number of trends from the AM literature including grain refinement, the dominance of layers with larger melt pools on the final grain structure, and the weakening or strengthening of texture depending on odd and even layer melt pool overlap geometry. EBSD data from a benchmark AM part is used to validate the simulated mechanism of a layer rotation-induced texture strengthening effect. Importantly, these results expand the understanding of the mechanisms for texture selection in alloys with cubic crystal symmetry and offer an approach to easily evaluate processing conditions. With this new understanding, these modeling tools will enable anticipation of previously unexpected variations in grain structure and target specific microstructures and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the influence of boron in additively manufactured GammaPrint®-700 CoNi-based superalloy

Boron is commonly added to superalloys in small amounts to enhance creep resistance, but can lead to cracking at high concentrations, especially during the additive manufacturing process. Two variants of CoNi-based GammaPrint®-700 superalloy with different B contents (0.08 at% vs 0.16 at%) were printed via laser powder bed fusion (LPBF) with the same printing parameters, with only the high B alloy exhibiting solidification cracking. Atom probe tomography (APT) revealed stronger segregation behaviors in the high B alloy compared to the low B alloy at both the inter-dendritic regions and grain boundaries (GBs). The segregation behavior at inter-dendritic regions was well captured with Scheil simulation and can correlate with the existing cracking susceptibility index (CSI) on cracking tendencies, although high angle GBs are where cracking occurs according to electron backscatter diffraction (EBSD) measurements. Additionally, the extent of GB segregation was compared between the high B and low B alloy. Higher B additions led to significantly more GB B segregation in the high B alloy compared to the low B alloy. Further, for the high B alloy, the cracked region of one GB exhibited higher levels of B compared to the uncracked region of the same GB. However, much higher B contents were also found in two other uncracked GBs in the high B alloy, which demonstrates that higher GB B concentrations are not fully responsible for the cracking. A much larger variance in GB B segregation content was found in the high B alloy compared to the low B alloy. These phenomena were explained with a solidification model with the GB segregation content expressed explicitly by a modified Langmuir-McLean equation. This model linked the GB segregation content with solidification undercooling, which can be used as quantitative cracking criteria for future builds.

36 MATERIALS SCIENCE↗