Search NASA⌕ Search

SEARCH · Search NASA

Results for “Laser cooling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

1.1 J Yb:YAG picosecond laser at 1 kHz repetition rate

We demonstrate the generation of 1.1 J pulses of picosecond duration at 1 kHz repetition rate (1.1 kW average power) from a diode-pumped chirped pulse amplification Yb:YAG laser. The laser employs cryogenically cooled amplifiers to generate λ <#comment/> = 1030 n m pulses with average power of up to 1.26 kW prior to compression with excellent beam quality. Pulses are compressed to 4.5 ps duration with 90% efficiency. This compact picosecond laser will enable a variety of applications that require high energy ultrashort pulses at kilohertz repetition rates.

Wang, Yong↗

Spectral performance of monolithic holmium and thulium lasers

Fabry-Perot resonators have been used to demonstrate single-mode lasing of holmium and neodymium YAG. The previous demonstration in the holmium laser required TE cooling the crystal to -15 C in order to achieve threshold. The present study extends that result, demonstrating +25 C operation in a 1-mm thick plano/plano resonator. The experimental configuration of lasing both the holmium and thulium lasers used a 500-mW diode laser which was collimated, circularized, and focused into a beam radius of 60 microns. The single-frequency lasing spectrum of the holmium laser is shown. By adjusting the mirror reflectivity, the ability to control the laser's wavelength is demonstrated. This laser operated with 11 mW of optical power, a 57-percent slope efficiency, and 120-mW threshold vs absorbed diode power laser for the 60-micron beam radius. The thulium laser operated very efficiently at room temperature, but on seven longitudinal modes. The Tm:TAG laser exhibits typical characteristics of spatial hole burning not seen in the Ho:Tm:YAG for flat/flat resonators.

Storm, Mark E.↗

Compact Laser-Based Sensors for Monitoring and Control of Gas Turbine Combustors

Research is reported on the development of sensors for gas turbine combustor applications that measure real-time gas temperature using near-infrared water vapor absorption and concentration in the combustor exhaust of trace quantities of pollutant NO and CO using mid-infrared absorption. Gas temperature is extracted from the relative absorption strength of two near-infrared transitions of water vapor. From a survey of the water vapor absorption spectrum, two overtone transitions near 1800 nm were selected that can be rapidly scanned in wavelength by injection current tuning a single DFB diode laser. From the ratio of the absorbances on these selected transitions, a path-integrated gas temperature can be extracted in near-real time. Demonstration measurements with this new temperature sensor showed that combustor instabilities could be identified in the power spectrum of the temperature versus time record. These results suggest that this strategy is extremely promising for gas turbine combustor control applications. Measurements of the concentration of NO and CO in the combustor exhaust are demonstrated with mid-infrared transitions using thermo-electrically cooled, quantum cascade lasers operating near 5.26 and 4.62 microns respectively. Measurements of NO are performed in an insulated exhaust duct of a C2H4-air flame at temperatures of approximately 600 K. CO measurements are performed above a rich H2-air flame seeded with CO2 and cooled with excess N2 to 1150 K. Using a balanced ratiometric detection technique a sensitivity of 0.36 ppm-m was achieved for NO and 0.21 ppm-m for CO. Comparisons between measured and predicted water-vapor and CO2 interference are discussed. The mid-infrared laser quantum cascade laser technology is in its infancy; however, these measurements demonstrate the potential for pollutant monitoring in exhaust gases with mid-IR laser absorption.

Hanson, Ronald K.↗

Thermomagnetic recording and magnetic-optic playback system

A magnetic recording and magneto-optic playback system is disclosed wherein thermomagnetic recording is employed. A transparent isotropic film is heated along a continuous path by a focused laser beam. As each successive area of the path is heated locally to the vicinity of its Curie point in the presence of an applied magnetic field, a magneto-optic density is established proportional to the magnetic field and fixed in place as the area cools once the laser beam moves on to an adjacent area. To play back the recorded data, the intensity of the laser beam is reduced to avoid reaching the vicinity of the Curie point of the film as it is scanned by the laser beam in the same manner as for recording. A Faraday effect analyzer and photo detector are employed as a transducer for producing an output signal.

Lewicki, G. W.↗

Project LOCOST: Laser or Chemical Hybrid Orbital Space Transport

A potential mission in the late 1990s is the servicing of spacecraft assets located in GEO. The Geosynchronous Operations Support Center (GeoShack) will be supported by a space transfer vehicle based at the Space Station (SS). The vehicle will transport cargo between the SS and the GeoShack. A proposed unmanned, laser or chemical hybrid orbital space transfer vehicle (LOCOST) can be used to efficiently transfer cargo between the two orbits. A preliminary design shows that an unmanned, laser/chemical hybrid vehicle results in the fuel savings needed while still providing fast trip times. The LOCOST vehicle receives a 12 MW laser beam from one Earth orbiting, solar pumped, iodide Laser Power Station (LPS). Two Energy Relay Units (ERU) provide laser beam support during periods of line-of-sight blockage by the Earth. The baseline mission specifies a 13 day round trip transfer time. The ship's configuration consist of an optical train, one hydrogen laser engine, two chemical engines, a 18 m by 29 m box truss, a mission-flexible payload module, and propellant tanks. Overall vehicle dry mass is 8,000 kg. Outbound cargo mass is 20,000 kg, and inbound cargo mass is 6,000 kg. The baseline mission needs 93,000 kg of propellants to complete the scenario. Fully fueled, outbound mission mass is 121,000 kg. A regeneratively cooled, single plasma, laser engine design producing a maximum of 768 N of thrust is utilized along with two traditional chemical engines. The payload module is designed to hold 40,000 kg of cargo, though the baseline mission specifies less. A proposed design of a laser/chemical hybrid vehicle provides a trip time and propellant efficient means to transport cargo from the SS to a GeoShack. Its unique, hybrid propulsion system provides safety through redundancy, allows baseline missions to be efficiently executed, while still allowing for the possibility of larger cargo transfers.

Dixon, Alan↗

Laser Raman sensor for measurement of trace-hydrogen gas

A new optical hydrogen sensor based on spontaneous Raman scattering of laser light has been designed and constructed for rugged field use. It provides good sensitivity, rapid response, and the inherent Raman characteristics of linearity and background gas independence of the signal. Efficient light collection and discrimination by using fast optics and a bandpass interference filter compensate for the inefficiency of the Raman-scattering process. A multipass optical cavity with a Herriott-type configuration provides intense illumination from an air-cooled CW gas laser. The observed performance is in good agreement with the theoretical signal and noise level predictions.

Adler-Golden, Steven M.↗

High Efficiency End-Pumped Ho:Tm:YLF Disk Amplifier

Space based coherent lidar for global wind measurement requires an all solid state laser system with high energy, high efficiency and narrow linewidth that operates in the eye safe region. A Q-switched, diode pumped Ho:Tm:YLF 2 micrometer laser with output energy of as much as 125 mJ at 6 Hz with an optical-to-optical efficiency of 3% has been reported. Single frequency operation of the laser was achieved by injection seeding. The design of this laser is being incorporated into NASA's SPARCLE (SPAce Readiness Coherent Lidar Experiment) wind lidar mission. Laser output energy ranging from 500 mJ to 2 J is required for an operational space coherent lidar. We previously developed a high energy Ho:Tm:YLF master oscillator and side pumped power amplifier system and demonstrated a 600-mJ single frequency pulse at a repetition rate of 10 Hz. Although the output energy is high, the optical-to-optical efficiency is only about 2%. Designing a high energy, highly efficient, conductively cooled 2-micrometer laser remains a challenge. In this paper, the preliminary result of an end-pumped amplifier that has a potential to provide a factor 3 of improvement in the system efficiency is reported.

Yu, Jirong↗

Liner environment effects study

The Liner Environment Effects Study Program is aimed at establishing a broad heat transfer data base under controlled experimental conditions by quantifying the effects of the combustion system conditions on the combustor liner thermal loading and on the flame radiation characteristics. Five liner concepts spanning the spectrum of liner design technology from the very simple to the most advanced concepts are investigated. These concepts comprise an uncooled liner, a conventional film cooled liner, an impingement/film cooled liner, a laser drilled liner approaching the concept of a porous wall, and a siliconized silicon carbide ceramic liner. Effect of fuel type is covered by using fuels containing 11.8, 12.8, and 14% hydrogen. Tests at 100, 200, and 300 psia provide a basis for evaluating the effect of pressure on the heat transfer. The effects of the atomization quality and spray characteristics are examined by varying the fuel spray Sauter mean diameter and the spray angle. Additional varied parameters include reference velocity, a wide range of equivalence ratio, cooling flow rate, coolant temperature and the velocity of the coolant stream on the backside of the liner.

Venkataramani, K. S.↗

Effect of Cooling Rate on Nano-Eutectic Formation in Laser Surface Remelted and Rare Earth Modified Hypereutectic Al-20Si Alloys

Laser Surface Remelting (LSR) was applied to arc-melted Al-20Si-0.2Sr, Al-20Si-0.2Ce, and Al-20Si hypereutectic alloys to refine microstructures. Experiments revealed that microstructures in the melt pool varied from fully eutectic to a mixture of Al dendrites and inter-dendritic eutectic. We calculated cooling rates using the Eagar-Tsai model and correlated cooling rates with characteristic microstructures, revealing that a cooling rate on the order of 104 K/s could lead to maximized fully eutectic microstructure morphology. Due to rapid solidification, the Si composition in the LSR eutectic was measured at 18.2 wt.%, higher than the equilibrium eutectic composition of 12.6 wt.%Si. Compared to Al-20Si, Ce addition had no significant effect on the volume fraction of the fully eutectic structure but refined Si fibers to approximately 30 nm in diameter. Sr addition did not further refine the diameter of eutectic Si fibers compared to Al-20Si but increased the volume fraction of the fully eutectic microstructure morphology. The refinement ratio (φ) of the Si fiber diameter from the bottom of the melt pool to the surface for the three alloys was similar, at around 28%. The established correlation between the cooling rate and the size and morphology of the microstructure within the melt pool will enable tailoring of the microstructure in laser-processed as well as deposited alloys for high strength and plasticity.

36 MATERIALS SCIENCE↗

NASA Tech Briefs, August 2005

Topics include: Hidden Identification on Parts: Magnetic Machine-Readable Matrix Symbols; System for Processing Coded OFDM Under Doppler and Fading; Multipurpose Hyperspectral Imaging System; Magnetic-Flux-Compensated Voltage Divider; High-Performance Satellite/Terrestrial-Network Gateway; Internet-Based System for Voice Communication With the ISS; Stripline/Microstrip Transition in Multilayer Circuit Board; Dual-Band Feed for a Microwave Reflector Antenna; Quadratic Programming for Allocating Control Effort; Range Process Simulation Tool; Simulator of Space Communication Networks; Computing Q-D Relationships for Storage of Rocket Fuels; Contour Error Map Algorithm; Portfolio Analysis Tool; Glass Frit Filters for Collecting Metal Oxide Nanoparticles; Anhydrous Proton-Conducting Membranes for Fuel Cells; Portable Electron-Beam Free-Form Fabrication System; Miniature Laboratory for Detecting Sparse Biomolecules; Multicompartment Liquid-Cooling/Warming Protective Garments; Laser Metrology for an Optical-Path-Length Modulator; PCM Passive Cooling System Containing Active Subsystems; Automated Electrostatics Environmental Chamber; Estimating Aeroheating of a 3D Body Using a 2D Flow Solver; Artificial Immune System for Recognizing Patterns; Computing the Thermodynamic State of a Cryogenic Fluid; Safety and Mission Assurance Performance Metric; Magnetic Control of Concentration Gradient in Microgravity; Avionics for a Small Robotic Inspection Spacecraft; and Simulation of Dynamics of a Flexible Miniature Airplane.

Source record↗

Cesium intercalation of graphene: A 2D protective layer on alkali antimonide photocathode

Alkali antimonide photocathodes have wide applications in free-electron lasers and electron cooling. The short lifetime of alkali antimonide photocathodes necessitates frequent replacement of the photocathodes during a beam operation. Furthermore, exposure to mediocre vacuum causes loss of photocathode quantum efficiency due to the chemical reaction with residual gas molecules. Theoretical analyses have shown that covering an alkali antimonide photocathode with a monolayer graphene or hexagonal boron nitride protects it in a coarse vacuum environment due to the inhibition of chemical reactions with residual gas molecules. Alkali antimonide photocathodes require an ultra-high vacuum environment, and depositing a monolayer 2D material on it poses a serious challenge. In the present work, we have incorporated a novel method known as intercalation, in which alkali atoms pass through the defects of a graphene thin film to create a photocathode material underneath. Initially, Sb was deposited on a Si substrate, and a monolayer graphene was transferred on top of the Sb film. Heat cleaning around 550–600 °C effectively removed the Sb oxides, leaving metallic Sb underneath the graphene layer. Depositing Cs on top of a monolayer graphene enabled the intercalation process. Atomic force microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, low energy electron microscopy, and x-ray diffraction measurements were performed to evaluate photocathode formation underneath the monolayer graphene. Our analysis shows that Cs penetrated the graphene and reacted with Sb and formed Cs 3 Sb.

2D materials↗

The Influence of Environment on Post-Detonation Chemistry and Debris Formation (Abbreviated Final Report: 20-SI-006)

Predicting, responding to, or interpreting the chemical record preserved in debris derived from nuclear events can be challenging due to chemical fractionation. Chemical fractionation is where different species of the evolving radionuclide inventory segregate and/or are lost from the system over the timescales of debris formation. Both historic data and recent research suggest that the interaction and character of the local environment may exert controls on chemical fractionation by influencing the cooling and evolution of the associated fireball as well as the composition of the vapor term and resultant speciation. Prior to this work, an integrated platform permitting dynamic and concurrent consideration of physical and chemical evolution of early time post-detonation event environments did not exist. Our work merged historic data and experimental approaches to support development of a computational framework able to simulate fundamental processes (e.g., entrainment of local environment, oxidation chemistry, and cooling time scales) that may perturb the radionuclide inventory captured in post-detonation debris. Work with historic debris confirmed that entrained environmental material affect debris composition, structure, and radionuclide incorporation. Complementary work utilizing a readily controllable and tunable benchtop setup (a plasma flow reactor) simulated the late cooling of a nuclear fireball (e.g., T < 6000 K) and bounded the sensitivity of actinide speciation and particle size distribution to variations in oxygen concentration and cooling rates. Concurrent laser ablation and laser heating experiments were used to investigate the chemistry and physics of processes occurring in vaporized and/or rapidly heated actinides and other elements in the presence of oxygen. A more computationally efficient microphysical model was developed for predicting and evolving size distributions of particles forming from mixed vapor terms and simulating particle formation processes under a variety of extreme conditions. Continued study of historic nuclear event film confirmed that shockwave data and physics codes agree to within the uncertainty of the data. Good agreement was achieved for thermal emission from an airburst, however the paucity of low-temperature molecular opacity data for mixtures of air, bomb debris, entrained dirt, and water vapor complicate agreement for more elaborate scenarios. A multiphysics code (ALE3D) was modified to bring the necessary physics and chemistry, including these new data and insights, onto a single platform. Code development included improved initialization of large physical systems, modernization of chemistry capabilities, and modifications to enable inclusion of particle transport.

07 ISOTOPE AND RADIATION SOURCES↗

Thermal Remote Anemometer Device

Thermal Remote Anemometer Device developed for remote, noncontacting, passive measurement of thermal properties of sample. Model heated locally by scanning laser beam and cooled by wind in tunnel. Thermal image of model analyzed to deduce pattern of airflow around model. For materials applications, system used for evaluation of thin films and determination of thermal diffusivity and adhesive-layer contact. For medical applications, measures perfusion through skin to characterize blood flow and used to determine viabilities of grafts and to characterize tissues.

Heyman, Joseph S.↗

Thermal Strap And Cushion For Thermoelectric Cooler

Inexpensive cushioning strap proposed for use as thermal contact between thermoelectric cooler and device to be cooled, such as laser diode, infrared detector, or charge-coupled device for imaging. Provides high thermal conductance while minimizing thermal and mechanical stresses on thermoelectric cooler. Used as alternative to flexible thermal strap made of silver.

Jones, Jack A.↗

Pollutant emissions from and within a model gas turbine combustor at elevated pressures and temperatures

Conventional and advanced gas turbine engines are coming under increased scrutiny regarding pollutant emissions. This, in turn, has created a need to obtain in-situ experimental data at practical conditions, as well as exhaust data, and to obtain the data in combustors that reflect modern designs. The in-situ data are needed to (1) assess the effects of design modifications on pollutant formation, and (2) develop a detailed data base on combustor performance for the development and verification of computer modeling. This paper reports on a novel high pressure, high temperature facility designed to acquire such data under controlled conditions and with access (optical and extractive) for in-situ measurements. To evaluate the utility of the facility, a model gas turbine combustor was selected which features practical hardware design, two rows of jets (primary and dilution) with four jets in each row, and advanced wall cooling techniques with laser drilled effusive holes. The dome is equipped with a flat-vaned swirler with vane angles of 60 degrees. Data are obtained at combustor pressures ranging from 2 to 10 atmospheres of pressure, levels of air preheat to 427 C, combustor reference velocities from 10.0 to 20.0 m/s, and an overall equivalence ratio of 0.3. Exit plane and in-situ measurements are presented for HC, O2, CO2, CO, and NO(x). The exit plane emissions of NO(x) correspond to levels reported from practical combustors and the in-situ data demonstrate the utility and potential for detailed flow field measurements.

Drennan, S. A.↗

Experiments with Ultracold Quantum-degenerate Fermionic Lithium Atoms

Experimental methods of laser and evaporative cooling, used in the production of atomic Bose-Einstein condensates have recently been extended to realize quantum degeneracy in trapped Fermi gases. Fermi gases are a new rich system to explore the implications of Pauli exclusion on scattering properties of the system, and ultimately fermionic superfluidity. We have produced a new macroscopic quantum system, in which a degenerate Li-6 Fermi gas coexists with a large and stable Na-23 BEC. This was accomplished using inter-species sympathetic cooling of fermionic 6Li in a thermal bath of bosonic Na-23. We have achieved high numbers of both fermions (less than 10(exp 5) and bosons (less than 10(exp 6), and Li-6 quantum degeneracy corresponding to one half of the Fermi temperature. This is the first time that a Fermi sea was produced with a condensate as a "refrigerator".

Ketterle, Wolfgang↗