Search NASA⌕ Search

SEARCH · Search NASA

Results for “Layer top”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Introduction to Tools and Techniques for Surface Sampling on Europa

The NASA Jet Propulsion Laboratory (JPL) is studying excavation and collection of a sample from an icy surface for a potential landed mission to Europa. Europa presents unique challenges in planetary sampling. Very little is known about the local topography and material composition of the surface. The environmental conditions of being cryogenically cold (80-130K), low gravity (~1/7th Earth), no atmosphere, low lighting conditions, and limited ground in the loop opportunities have forced JPL to look at sampling differently than past missions. Interacting with the surface of the Jovian moon requires a sampling system that is robust to local topography on the scale of the lander and/or the tool. In addition, the sampling system must be capable both of detecting faults and automatically adjusting to them to achieve the mission objectives without ground in the loop feedback. Presented here is an overview of a sampling system concept that involves a two-stage approach for collecting a sample. The first stage uses an excavation tool to prepare the surface site for sample collection by removing the top layer of irradiated material and clearing tailings from the hole. The second stage then generates and collects a sample for delivery to instruments on-board a lander. Also presented is an introduction for how autonomy and sensing technologies might be employed to enable mission success.

Tevere, Erica L.↗
NASA NTRSDate not supplied

A Compact Dual-Band Bowtie Antenna for RF and ISM bands Operation

Traditionally, bowtie antennas have been known to exhibit wide impedance characteristics, omnidirectional radiation patterns, and linear polarization. There is a broad range of applications from medical imaging, archaeological survey, and Ground Penetrating Radar (GPR) to trackers and sensor networks where wideband bowtie antenna designs are required for their operations. Broadening the bandwidth of bowtie antenna requires widening the flare angle of the bowtie arms, which consequently results in a large surface area that may not be suitable for space-constrained applications. Moreover, drawback attributes of the wideband bowtie designs feature inconsistent radiation pattern across the bandwidth and low signal-to-noise (SNR) ratios. As it is known, the SNR would be improved in dual- or multi-band antennas due to their reduced bandwidth. To this end, dual-band/multi-band antennas are preferred over wideband antennas in applications where more than a single frequency of interest is present. Previously, a two-port double-dipole elements was reported, whose arms were orthogonally interleaved to facilitate operation in both the standard WLAN frequency bands (J. M. Steyn and et. al, Progress in Electromagnetic Research, Vol. – 10 pp. 151-161). Even though the antenna is not very compact it does exhibit good cross-polarization, moderate gain in both frequency bands. Another dual-band bowtie antenna which excites two bands using a single transmission line was reported (Wen Chao Zheng and et. al, IEEE Trans. Antennas propag., 2014). The design was compact and did not need multi-port feeding network. In this paper, a dual-band compact bowtie antenna operating at 900 MHz (RF band) and 2.45 GHz (ISM band) using a single excitation port is introduced. It is printed on a 1.54mm thick dielectric substrate (εr = 3.38). The antenna consists of two sets of bowtie arms, a microstrip transmission line to feed the bowtie arms, and a ground plane acting as a reflector to partially reduce the back radiation. One of the bowtie arms of each frequency is printed on the top layer and the other arm, which is mirror imaged, is printed on the bottom layer of the substrate. The length of the bowtie controls the resonance frequency of the antenna and the flare angle controls the bandwidth of the antenna. The microstrip transmission line, connected to a 50 Ω SMA probe, feeds the bowtie antenna. The compact antenna can be used for both RF and ISM band applications. The bowtie arms at the lower frequency band are miniaturized by elongating their electrical lengths. The influence of miniaturizing the bowtie arms and the supporting partial ground plane is observed in the reduced peak gain and degraded front-to-back ratio. These are partly neutralized using four quarter-wave choke-slots in the ground plane with two on each side of the feeding transmission line. The proposed antenna is numerically investigated and finalized by the finite-element based full-wave EM solver, ANSYS HFSS. The miniaturization has reduced the ground plane size by ~45% and the arms size by ~41%. In addition to the size reduction benefits, the antenna shows reasonable peak gain and front-to-back ratio in both the bands. The corresponding results will be presented and discussed at the conference.

Saininad Naik↗
NASA NTRS2021

Acoustic Communication in Deep Ice at Ocean Worlds

One of NASA priorities is the in-situ exploration of ocean worlds in the solar system where potentially there might be life under the ice shell. This requires reaching the ocean below extremely cold through significant deep ice. Jupiter’s moon, Europa, is such a challenging body, where it is estimated to have a 40 km thick ice shell. An approach for reaching the ocean has been conceived using a melting probe Cryobot concept that has been studied for a potential future mission. A lander is assumed to be the platform from which the Cryobot would be deployed. The ice penetrating vehicle concept consists of a cylindrical, narrow-body probe that encases a radioisotope heat/power source that would be used to do the penetration by melting through the icy crust. The baseline design of the probe includes a suite of science instruments to analyze the ice during descent and the liquid ocean underneath. For communication, a set of fiber optic wire as well as wireless RF in the very cold porous top layer is assumed, and then acoustic modules would be used for the communication in warmer denser ice over distance of 25 km between the modules. In addition to the acoustic communication modules, a sonar is part of the concept, for obstacle avoidance. The focus of this paper is on the use of elastic waves in the 1kHz range.

Lih, Shyh-Shiuh↗
NASA NTRSDate not supplied

Enabling Space Biological Knowledge Discovery Through Image and Video Data Sharing

Increased biomedical risks and challenges associated with deep space missions and experiments (cis-Lunar, Mars transit/surface) require new knowledge discovery and development of novel ecosystems. Supporting distant and long-duration missions and experiments requires biological data (from yeast, microbes, fruit flies, C. elegans, plants, crops, rodents, humans) be findable, accessible, interoperable, reusable (FAIR), and maximally open-access. As data-intensive, bioinformatic, meta-analytical, and computer-assisted approaches continue to be a centerpiece of modern research, the NASA Biological and Physical Sciences division is expanding its Open Science capabilities beyond NASA GeneLab. The NASA Ames Life Sciences Data Archive (ALSDA) is a repository which is responsible for collecting and access to space biological imagery and video, alongside tabular and environmental data. In this presentation, we will discuss strategies dealing with archiving, curating, and accessibility of images from very distinct imaging modalities (e.g., micro-computed tomography, magnetic resonance imaging, photographic images of plants, fluorescence microscopy, behavioral videos, etc.). There are two main challenges: 1. Open-source data storage and 2. Metadata related to the imagery-video. Both have been solved by leveraging two existing open-source systems. For data storage, ALSDA is utilizing components through the Open Microscopy Environment (OME), which can read most imaging proprietary formats and display on a web interface complex multidimensional images (Z stack, multi-channel, temporal, spectral). Most technical metadata from imaging modalities are captured seamlessly. For metadata capturing experimental details, ALSDA (like GeneLab) uses the ISA-Tab specification which relies on the ISA data model to order and classify metadata. The ISA data model uses a tree structure with three files to capture the metadata: The top layer is the Investigations file, the second layer is the Study file(s), and the last layer is the Assay file(s). We believe such an approach may be useful for other types of image research data from other investigators in the AGU community.

imaging↗
NASA NTRS2023

Modulation of the Seasonal Cycle of the Antarctic Sea Ice Extent By Sea Ice Processes and Feedbacks With the Ocean and the Atmosphere

The seasonal cycle of the Antarctic sea ice extent is strongly asymmetric, with a relatively slow increase after the summer minimum followed by a more rapid decrease after the winter maximum. This cycle is intimately linked to the seasonal cycle of the insolation received at the top of the atmosphere, but sea ice processes as well as the exchanges with the atmosphere and ocean may also play a role. To quantify these contributions, a series of idealized sensitivity experiments have been performed with an eddy-permitting (∘) NEMO-LIM3 (Nucleus for European Modelling of the Ocean–Louvain-la-Neuve sea ice model version 3) Southern Ocean configuration, including a representation of ice shelf cavities, in which the model was either driven by an atmospheric reanalysis or coupled to the COSMO-CLM2 regional atmospheric model. In those experiments, sea ice thermodynamics and dynamics as well as the exchanges with the ocean and atmosphere are strongly perturbed. This perturbation is achieved by modifying snow and ice thermal conductivities, the vertical mixing in the ocean top layers, the effect of freshwater uptake and release upon sea ice growth and melt, ice dynamics, and surface albedo. We find that the evolution of sea ice extent during the ice advance season is largely independent of the direct effect of the perturbation and appears thus mainly controlled by initial state in summer and subsequent insolation changes. In contrast, the melting rate varies strongly between the experiments during the retreat, in particular if the surface albedo or sea ice transport are modified, demonstrating a strong contribution of those elements to the evolution of ice coverage through spring and summer. As with the advance phase, the retreat is also influenced by conditions at the beginning of the melt season in September. Atmospheric feedbacks enhance the model winter ice extent response to any of the perturbed processes, and the enhancement is strongest when the albedo is modified. The response of sea ice volume and extent to changes in entrainment of subsurface warm waters to the ocean surface is also greatly amplified by the coupling with the atmosphere.

regional atmosphere ocean sea ice model↗
NASA NTRS2023

Importance of Atmospheric Feedbacks in Simulating the Seasonal Cycle of the Antarctic Sea Ice and Its Response to Perturbations

The seasonal cycle of the Antarctic sea ice extent is largely controlled by the evolution of the insolation received at the top of the atmosphere. However, sea ice processes and feedbacks with the ocean and the atmosphere can modulate this seasonal cycle. Here, the atmospheric feedbacks are quantified in a series of idealized sensitivity experiments performed with an eddy-permitting (1/4°) NEMO-LIM3 Southern Ocean configuration, including a representation of ice shelf cavities, in which the model was either driven by an atmospheric reanalysis or coupled to the COSMO-CLM 2 regional atmospheric model. In these experiments, sea ice thermodynamics and dynamics as well as the exchanges with the ocean and atmosphere are strongly perturbed. This perturbation is achieved by modifying snow and ice thermal conductivities, the vertical mixing in the ocean top layers, the effect of freshwater uptake/release upon sea ice growth/melt, ice dynamics and surface albedo. We show that the changes in surface heat fluxes are very different between the configurations driven by the reanalysis and those coupled to the atmosphere. Atmospheric feedbacks enhance the response of the modelled winter ice extent to any of the perturbed processes, and the enhancement is strongest when the albedo is modified. The response of sea ice volume and extent to changes in entrainment of subsurface warm waters to the ocean surface is also greatly amplified by the coupling with the atmosphere. By contrast, the atmospheric feedbacks can damp the impact of the perturbations affecting the heat conductivity through sea ice.

Atmospheric feedbacks↗
NASA NTRS2023

Sensitivity of the MAR Regional Climate Model Snowpack to the Parameterization of the Assimilation of Satellite-Derived Wet-Snow Masks on the Antarctic Peninsula

Both regional climate models (RCMs) and remote sensing (RS) data are essential tools in understanding the response of polar regions to climate change. RCMs can simulate how certain climate variables, such as surface melt, runoff and snowfall, are likely to change in response to different climate scenarios but are subject to biases and errors. RS data can assist in reducing and quantifying model uncertainties by providing indirect observations of the modeled variables on the present climate. In this work, we improve on an existing scheme to assimilate RS wet snow occurrence data with the “Modèle Atmosphérique Régional” (MAR) RCM and investigate the sensitivity of the RCM to the parameters of the scheme. The assimilation is performed by nudging the MAR snowpack temperature to match the presence of liquid water observed by satellites. The sensitivity of the assimilation method is tested by modifying parameters such as the depth to which the MAR snowpack is warmed or cooled, the quantity of water required to qualify a MAR pixel as “wet” (0.1 % or 0.2 % of the snowpack mass being water), and assimilating different RS datasets. Data assimilation is carried out on the Antarctic Peninsula for the 2019–2021 period. The results show an increase in meltwater production (+66.7 % on average, or +95 Gt), along with a small decrease in surface mass balance (SMB) (−4.5 % on average, or −20 Gt) for the 2019–2020 melt season after assimilation. The model is sensitive to the tested parameters, albeit with varying orders of magnitude. The prescribed warming depth has a larger impact on the resulting surface melt production than the liquid water content (LWC) threshold due to strong refreezing occurring within the top layers of the snowpack. The values tested for the LWC threshold are lower than the LWC for typical melt days (approximately 1.2 %) and impact results mainly at the beginning and end of the melting period. The assimilation method will allow for the estimation of uncertainty in MAR meltwater production and will enable the identification of potential issues in modeling near-surface snowpack processes, paving the way for more accurate simulations of snow processes in model projections.

regional climate models↗
NASA NTRS2023

Considering Soil Moisture in Models of Climate Impacts on Child Health in Farming-Centric Countries

Soil moisture reflects the amount of water available to crops in the top layer of soil. As such, considering soil moisture provides important insight into water availability and ultimately crop yields in agricultural settings. In studies of climate change, food security, and health, however, soil moisture is rarely empirically considered despite its connection to crop health and yields. In this project, we aim to advance understanding of climate impacts on food security by incorporating soil moisture into quantitative models of child health. Combining spatially referenced health survey data from the Demographic and Health Surveys for 2005 and 2010 in Senegal and 2007, 2011, and 2014 in Bangladesh, with soil moisture data from the Famine Early Warning System Network Land Data Assimilation System, we explore the linkages between sub-annual and sub-seasonal climate conditions and child malnutrition in two rainfed agriculture dependent countries—Bangladesh and Senegal. Results suggest that soil moisture, measured on very short time scales, may be associated with reductions in anthropometric weight-for-height z-scores, but the relationship is highly dependent upon geographic context.

Child health↗
NASA NTRS2024

Global Sensitivity Analysis of Simulated Remote Sensing Polarimetric Observations Over Snow

This study presents a detailed theoretical assessment of the information content of passive polarimetric observations over snow scenes, using a global sensitivity analysis (GSA) method. Conventional sensitivity studies focus on varying a single parameter while keeping all other parameters fixed. In contrast, the GSA correctly addresses the covariance of state parameters across their entire parameter space, hence favoring a more correct interpretation of inversion algorithms and the optimal design of their state vectors. The forward simulations exploit a vector radiative transfer model to obtain the Stokes vector emerging at the top of the atmosphere for different solar zenith angles, when the bottom boundary consists of a vertically resolved snowpack of non-spherical grains. The presence of light-absorbing particulates (LAPs), either embedded in the snow or aloft in the atmosphere above in the form of aerosols, is also considered. The results are presented for a set of wavelengths spanning the visible (VIS), near-infrared (NIR), and shortwave infrared (SWIR) region of the spectrum. The GSA correctly captures the expected, high sensitivity of the reflectance to LAPs in the VIS–NIR and to grain size at different depths in the snowpack in the NIR–SWIR. With adequate viewing geometries, mono-angle measurements of total reflectance in the VIS–SWIR (akin to those of the Moderate Resolution Imaging Spectroradiometer, MODIS) resolve grain size in the top layer of the snowpack sufficiently well. The addition of multi-angle polarimetric observations in the VIS–NIR provides information on grain shape and microscale roughness. The simultaneous sensitivity in the VIS–NIR to both aerosols and snow-embedded impurities can be disentangled by extending the spectral range to the SWIR, which contains information on aerosol optical depth while remaining essentially unaffected when the same particulates are mixed with the snow. Multi-angle polarimetric observations can therefore (i) effectively partition LAPs between the atmosphere and the surface, which represents a notorious challenge for snow remote sensing based on measurements of total reflectance only and (ii) lead to better estimates of grain shape and roughness and, in turn, the asymmetry parameter, which is critical for the determination of albedo. The retrieval uncertainties are minimized when the degree of linear polarization is used in place of the polarized reflectance. The Sobol indices, which are the main metric for the GSA, were used to select the state parameters in retrievals performed on data simulated for multiple instrument configurations. Improvements in retrieval quality with the addition of measurements of polarization, multi-angle views, and different spectral channels reflect the information content, identified by the Sobol indices, relative to each configuration. The results encourage the development of new remote sensing algorithms that fully leverage multi-angle and polarimetric capabilities of modern remote sensors. They can also aid flight planning activities, since the optimal exploitation of the information content of multi-angle measurements depends on the viewing geometry. The better characterization of surface and atmospheric parameters in snow-covered regions advances research opportunities for scientists of the cryosphere and ultimately benefits albedo estimates in climate models.

remote sensing↗
DOE OSTI2020

Production of Medium-Scale Metal Additive Geometry With Hybrid Manufacturing Technology

Oak Ridge National Lab’s (ORNL) Metal Big Area Additive Manufacturing (mBAAM) and Hybrid Manufacturing teams in the Manufacturing Demonstration Facility (MDF) was tasked with developing a part that exceeded 24 inches in length and 100lbs in weight on a laser hotwire welding system. The Mazak VC-500A/5X AM HWD hybrid 5-axis CNC laser hotwire system was leveraged to complete the task. The proposed geometry was manufactured with 410 stainless steel on AISI1018 steel substrate in just over 36 hours of build time. The proposed geometry was sliced and additively manufactured in three segments; the base, and two extrusions measuring 10 inches in length and 14 inches in length. Production of this component demonstrated hybrid capabilities requiring fixed 5-axis rotations to complete geometry that exceeded the defined build volume of the machine. Multiple repairs of the part were conducted in-situ leveraging the additive and subtractive capabilities of the Mazak hybrid system. Significant overbuilding challenges were encountered and manually addressed by leveraging subtractive capabilities of the hybrid system. Future processes are presented for development to reduce overheating of top layers. Final part measurements exceeded 107 lbs. in weight and 24.5 inches in length along the principal axis; the largest and heaviest part created by a hybrid system at the MDF.

Saleeby, Kyle↗
DOE OSTI2023

Simulation of Reverse Osmosis Membrane Compaction Using Material Point Method (MPM)

Access to fresh drinking water in the future requires effective management of industrial wastewater and water purification from available resources. In this study, we present the simulation methodology and the analysis of a Reverse Osmosis (RO) membrane under various pressure conditions using the Material Point Method (MPM). In contrast to other numerical methods, MPM solves the continuum governing equations on material points in a Lagrangian framework. The method does not require a grid connecting the material points hence making it suitable to simulate large deformations during membrane compaction. The time integration is carried out using the explicit Euler method, while the spatial discretization is performed using linear or cubic-spline shape functions. A series of planar images containing detailed pore structures obtained from X-ray tomography experiments is converted to a three-dimensional collection of material points to simulate the membrane. Compressive loads are applied to the top layer of the membrane to simulate the experiments. The membrane deformation and pore size distribution before and after load application are reported and compared with the experimental measurements. The presentation discusses the numerical methods used, the performance of the solver on high-performance computing machines, and the results of membrane compaction in detail.

ENGINEERING,MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Simulation of Reverse Osmosis Membrane Compaction Using Material Point Method

Reverse Osmosis (RO) is a promising technology to address the impending water-crisis in the upcoming decades. RO at high salinities and high pressures is challenging due to membrane compaction that changes its porosity and permeability. In this study, we present a simulation methodology for membrane structural mechanics to understand pore size distribution and permeability variations under high pressure. We use the material point method (MPM), that solves the solid mechanics equations in a Lagrangian framework. MPM provides many features that make it well-suited for simulating mesoporous membranes. The Lagrangian framework allows for large deformations, easy integration of constitutive models and direct import of complex geometries as particles. The spatial discretization in our MPM solver is achieved using linear or cubic-spline shape functions while the time integration is carried out using the explicit Euler method. A series of images containing detailed pore structures obtained from X-ray tomography is first converted to a collection of material points. Compressive loads are applied to the top layer of the membrane to simulate the application of pressure. The membrane deformation and pore size distribution before and after load application are reported and compared with the experimental measurements. The presentation discusses the numerical methods used, the performance of the solver on high-performance computing machines, and the results of membrane compact in detail.

compaction↗
NASA NTRS1985

N/P GaAs concentrator solar cells with an improved grid and bushbar contact design

The major requirements for a solar cell used in space applications are high efficiency at AMO irradiance and resistance to high energy radiation. Gallium arsenide, with a band gap of 1.43 eV, is one of the most efficient sunlight to electricity converters (25%) when the the simple diode model is used to calculate efficiencies at AMO irradiance, GaAs solar cells are more radiation resistant than silicon solar cells and the N/P GaAs device has been reported to be more radiation resistant than similar P/N solar cells. This higher resistance is probably due to the fact that only 37% of the current is generated in the top N layer of the N/P cell compared to 69% in the top layer of a P/N solar cell. This top layer of the cell is most affected by radiation. It has also been theoretically calculated that the optimized N/P device will prove to have a higher efficiency than a similar P/N device. The use of a GaP window layer on a GaAs solar cell will avoid many of the inherent problems normally associated with a GaAlAs window while still proving good passivation of the GaAs surface. An optimized circular grid design for solar cell concentrators has been shown which incorporates a multi-layer metallization scheme. This multi-layer design allows for a greater current carrying capacity for a unit area of shading, which results in a better output efficiency.

Desalvo, G. C.↗
NASA NTRS1986

Senstitivity analysis of horizontal heat and vapor transfer coefficients for a cloud-topped marine boundary layer during cold-air outbreaks

The effects of external parameters on the surface heat and vapor fluxes into the marine atmospheric boundary layer (MABL) during cold-air outbreaks are investigated using the numerical model of Stage and Businger (1981a). These fluxes are nondimensionalized using the horizontal heat (g1) and vapor (g2) transfer coefficient method first suggested by Chou and Atlas (1982) and further formulated by Stage (1983a). In order to simplify the problem, the boundary layer is assumed to be well mixed and horizontally homogeneous, and to have linear shoreline soundings of equivalent potential temperature and mixing ratio. Modifications of initial surface flux estimates, time step limitation, and termination conditions are made to the MABL model to obtain accurate computations. The dependence of g1 and g2 in the cloud topped boundary layer on the external parameters (wind speed, divergence, sea surface temperature, radiative sky temperature, cloud top radiation cooling, and initial shoreline soundings of temperature, and mixing ratio) is studied by a sensitivity analysis, which shows that the uncertainties of horizontal transfer coefficients caused by changes in the parameters are reasonably small.

Chang, Y. V.↗
NASA NTRS2003

Large-eddy Simulation of Stratocumulus-topped Atmospheric Boundary Layers with Dynamic Subgrid-scale Models

The objective of the present study is to evaluate the dynamic procedure in LES of stratocumulus topped atmospheric boundary layer and assess the relative importance of subgrid-scale modeling, cloud microphysics and radiation modeling on the predictions. The simulations will also be used to gain insight into the processes leading to cloud top entrainment instability and cloud breakup. In this report we document the governing equations, numerical schemes and physical models that are employed in the Goddard Cumulus Ensemble model (GCEM3D). We also present the subgrid-scale dynamic procedures that have been implemented in the GCEM3D code for the purpose of the present study.

Senocak, Inane↗
NASA NTRS1994

Roles of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer

This study focuses on the effects of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer. When the simulated drizzle rate is relatively small (maximum approximately equal to 0.6 mm/day), steady-state solutions are obtained. The boundary layer stabilizes essentially because drizzle causes evaporative cooling of the subcloud layer. This stabilization considerably reduces the buoyancy flux and turbulence kinetic energy below the stratus cloud. Thus, drizzle tends to decouple the cloud from the subcloud layer in the model, as suggested by many observational studies. In addition, the evaporation of drizzle in the subcloud layer creates small scattered clouds, which are likely to represent cumulus clouds, below the solid stratus cloud in the model. The sensitivity experiments show that these scattered clouds help maintain a coupled boundary layer. When the drizzle rate is relatively large (maximum approximately equal to 0.9 mm/day), the response of the model becomes transient with bursts in turbulent fluxes. This phenomenon is related to the formation of the scattered cloud layer below the solid stratus cloud. It appears that the model is inadequate to represent the heat and moisture transport by strong updrafts covering a small fractional area in cumulus convection.

Wang, Shouping↗
DOE OSTI2024

Round superconductor wires

A round superconductor wire and method for fabricating same are disclosed. Embodiments are directed to a round superconductor wire including at least two superconductor tapes wound on a wire former. Each superconductor tape includes: bottom stabilizer and silver layers; substrate disposed above the bottom silver layer; buffer film stack disposed above the substrate; superconductor film disposed above the buffer film stack; top silver layer disposed above the superconductor film; and top stabilizer layer disposed above the top silver layer. At least one of the bottom stabilizer layer, bottom silver layer, substrate, buffer film stack, superconductor film, top silver layer, or top stabilizer layer is of a different width, thickness, or material composition in one of the superconductor tapes than in another of the superconductor tapes. These and other embodiments achieve a round superconductor wire having improved current density in high magnetic field applications when made in small diameters.

Majkic, Goran↗
NASA NTRS1995

Identification And Survival Of Bacteriohopanepolyol In A Hot Spring Microbial Mat

The polar lipids of a hot spring microbial mat located in Yellowstone National Park were examined for the presence of bacteriohopanepolvols (BHP). BHP are a group of molecules consisting of a hopanoid (peotacyclic triterpene) linked via a n-alkyl polyhydroxylated chain to a variety of polar end groups. BHP have been isolated in varying amounts from phylogenetically diverse eubacterial groups including cyanobacteria, methanotrophs and the Rhodospirillaceae. The hopanoids are excellent biomarkers and have been detected in sedimentary rocks as old as 1.7 bya. In order to interpret the ancient organic record, it is important to understand the abundance, source and fate of such biomarker compounds in microbial mats. A 40 sq cm mat section was taken from a 52 to 55 C site in the effluent channel of Octopus Spring and was sampled vertically over approximately 16 mm. The first 5-6 mm was sectioned into a top green layer (310 mg dry weight) and several subjacent, deep orange layers (240 and 250 mg, respectively). The lower 10 mm of the mat was sectioned into two gelatinous orange layers containing a siliceous gritty material (260 and 440 mg) which increased with depth, and a bottom layer composed almost exclusively of siliceous sinter (4.1 g). The progressive decrease in total organic carbon from 45% in the top green layer to only 4% in the bottom layer reflects the observed increase in siliceous deposition. GC-MS analysis of the phospholipid and glycolipid fatty acids yielded predominantly saturated normal chain acids, n-15 to n-18, and iso-branched acids, i-15 to i-17. Small amounts of unsaturated fatty acids (16:1, two positional isomers of 18:1, and two cyclopropyl acids, C(sub 17) and C(sub 19)) were present mainly in the top layer. Esterified fatty acid which is a good index for intact cellular membrane, i.e. viable organisms, was highest in the top two layers (203 and 231 micro g/mg total lipid, respectively) and gradually decreased to 66 micro g/mg total lipid in the bottom layer. Small amounts of BHP were present in all six layers, however in this case, BHP was lowest in the top green and subjacent deep-orange layers (118 and 172 micro g/mg total lipid, respectively) and increased with depth reaching almost 400 micro g/mg in the bottom two layers. This data suggest that BHP are survivina the initial phase of mat degradation and may be preferentially enriched in any organic record of such thermal environments. The relatively low level of BHP in the top layer also suggests that cyanobacteria may not be the major source of BHP in this mat. Since Chloroflexus a major component of the deep-orange layer has been reported to lack BHP, this material may prove a valuable biomarker for some other mat inhabitant. Further isotopic characterization of this BHP should help resolve this finding.

Janke, Linda L.↗