SEARCH · Search NASA

Results for “Lift Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Tailored composite wings with elastically produced chordwise camber

Four structural concepts were created which produce chordwise camber deformation that results in enhanced lift. A wing box can be tailored to utilize each of these with composites. In attempting to optimize the aerodynamic benefits, researchers found that there are two optimum designs that are of interest. There is a weight optimum which corresponds to the maximum lift per unit structural weight. There is also a lift optimum that corresponds to maximum absolute lift. Experience indicates that a large weight penalty accompanies the transition from weight to lift optimum designs. New structural models, the basic deformation mechanisms that are utilized, and typical analytical results are presented. It appears that lift enhancements of sufficient magnitude can be produced to render this type of wing tailoring of practical interest.

Rehfield, Lawrence W.↗

NASA NTRS1984

Refined methods of aeroelastic analysis and optimization

Graduate research activity in the following areas is reported: the divergence of laminated composite lifting surfaces, subsonic propeller theory and aeroelastic analysis, and cross sectional resonances in wind tunnels.

Ashley, H.↗

NASA NTRS1989

Acoustic design considerations: Review of rotor acoustic sources

It is not sufficient to optimize a rotor design in terms of a single noise level calculated for a single flight condition and a single measurement location. The various noise sources, their frequency content, amplitude, and directivity as a function of operating condition must be considered. A summary of the frequency ranges, directivity patterns and the most important operational and design parameters for major rotor noise sources is presented. It is difficult to generalize design requirements for rotor noise because the acoustic output varies so widely depending on the noise source, flight condition, measurement location, and frequency range. However, assuming the rotor must lift a fixed nominal payload and operate over a wide range of flight conditions, three general design guidelines can be stated: (1) minimize tip Mach number; (2) minimize blade thickness in the tip region; and (3) minimize gradients in the spanwise lift distribution in the tip region. Constraints on blade thickness, maximum values for hover tip Mach number, advancing tip Mach number and spanwise lift coefficient gradient will be specified during the aerodynamic, dynamic and structural optimization process. The rotor noise sources to be considered include the low frequency loading and thickness noise, and the higher frequency noise due to blade-vortex interactions (BVI). The analyses to be employed will include the comprehensive rotor analysis and design program CAMRAD and the rotor noise prediction program WOPWOP.

Martin, Ruth M.↗

NASA NTRS2010

Modular Approach to Launch Vehicle Design Based on a Common Core Element

With a heavy lift launch vehicle as the centerpiece of our nation's next exploration architecture's infrastructure, the Advanced Concepts Office at NASA's Marshall Space Flight Center initiated a study to examine the utilization of elements derived from a heavy lift launch vehicle for other potential launch vehicle applications. The premise of this study is to take a vehicle concept, which has been optimized for Lunar Exploration, and utilize the core stage with other existing or near existing stages and boosters to determine lift capabilities for alternative missions. This approach not only yields a vehicle matrix with a wide array of capabilities, but also produces an evolutionary pathway to a vehicle family based on a minimum development and production cost approach to a launch vehicle system architecture, instead of a purely performance driven approach. The upper stages and solid rocket booster selected for this study were chosen to reflect a cross-section of: modified existing assets in the form of a modified Delta IV upper stage and Castor-type boosters; potential near term launch vehicle component designs including an Ares I upper stage and 5-segment boosters; and longer lead vehicle components such as a Shuttle External Tank diameter upper stage. The results of this approach to a modular launch system are given in this paper.

Creech, Dennis M.↗

NASA NTRS1977

Optimization of flexible wing structures subject to strength and induced drag constraints

An optimization procedure for designing wing structures subject to stress, strain, and drag constraints is presented. The optimization method utilizes an extended penalty function formulation for converting the constrained problem into a series of unconstrained ones. Newton's method is used to solve the unconstrained problems. An iterative analysis procedure is used to obtain the displacements of the wing structure including the effects of load redistribution due to the flexibility of the structure. The induced drag is calculated from the lift distribution. Approximate expressions for the constraints used during major portions of the optimization process enhance the efficiency of the procedure. A typical fighter wing is used to demonstrate the procedure. Aluminum and composite material designs are obtained. The tradeoff between weight savings and drag reduction is investigated.

Haftka, R. T.↗

NASA NTRS1977

Effects of lengthwise lift distribution on sonic boom of SST configurations

Sonic Boom signatures produced by possible SST configurations during cruise were investigated. It is shown that optimization based on a far field analysis is not necessarily the optimum for these conditions. For an airplane length of 300 ft, near-field effects can be obtained when sufficient lift is generated near the nose of the airplane. Because of the near-field effects, sonic booms with maximum overpressures of the order of 1 lb/square foot can be obtained with possible airplane configurations having the same flight conditions at cruise.

Ferri, A.↗

NASA NTRS2003

Performance Trades Study for Robust Airfoil Shape Optimization

From time to time, existing aircraft need to be redesigned for new missions with modified operating conditions such as required lift or cruise speed. This research is motivated by the needs of conceptual and preliminary design teams for smooth airfoil shapes that are similar to the baseline design but have improved drag performance over a range of flight conditions. The proposed modified profile optimization method (MPOM) modifies a large number of design variables to search for nonintuitive performance improvements, while avoiding off-design performance degradation. Given a good initial design, the MPOM generates fairly smooth airfoils that are better than the baseline without making drastic shape changes. Moreover, the MPOM allows users to gain valuable information by exploring performance trades over various design conditions. Four simulation cases of airfoil optimization in transonic viscous ow are included to demonstrate the usefulness of the MPOM as a performance trades study tool. Simulation results are obtained by solving fully turbulent Navier-Stokes equations and the corresponding discrete adjoint equations using an unstructured grid computational fluid dynamics code FUN2D.

Li, Wu↗

NASA NTRSDate not supplied

End-to-End Performance Optimization of a Crewed Lunar Landing Mission Staged from a Near Rectilinear Halo Orbit

A crewed lunar landing mission staged from a Near Rectilinear Halo Orbit (NRHO) presents a unique set of challenges not considered before for the Apollo-type direct missions. The NRHO does not have a fixed orbital plane and its period also changes with time, due to which the mission performance is very sensitive to the timing and location of the NRHO departure and arrival burns for a near-polar surface landing site. For such type of mission staged from the NRHO, an end-to-end optimization approach for the entire mission, from the NRHO departure to surface landing and from surface lift-off to the NRHO insertion, is well-suited for extracting the maximum performance out of this design. In this paper, an integrated approach for performing end-to-end optimization of a NRHO-staged crewed lunar landing mission is proposed that optimizes the in-space and powered flight segments simultaneously using Copernicus trajectory optimization tool. Copernicus is augmented with analytical approximations for the in-space, powered descent, and powered ascent segments in this work to improve the convergence of its multiple-shooting based direct optimization method. New analytical solutions are derived for the different phases of the powered flight segments by solving associated guidance problems. These analytical solutions act as initial guesses for starting the numerical optimization of the integrated mission in Copernicus. An example lunar landing mission is simulated to validate the proposed end-to-end optimization approach and the results are compared with the conventional patched trajectory approach.

Bharat Mahajan↗

NASA NTRS1926

Lattice arrangements for rapid convergence

A simple, systematic, optimized vortex-lattice approach is developed for application to lifting-surface problems. It affords a significant reduction in computational costs when compared to current methods. Extensive numerical experiments have been carried out on a wide variety of configurations, including wings with camber and single or multiple flaps, as well as high-lift jetflap systems. Rapid convergence as the number of spanwise or chordwise lattices are increased is assured, along with accurate answers. The results from this model should be useful not only in preliminary aircraft design but also, for example, as input for wake vortex roll-up studies and transonic flow calculations.

Hough, G. R.↗

NASA NTRS1997

Aerodynamic Shape Sensitivity Analysis and Design Optimization of Complex Configurations Using Unstructured Grids

A three-dimensional unstructured grid approach to aerodynamic shape sensitivity analysis and design optimization has been developed and is extended to model geometrically complex configurations. The advantage of unstructured grids (when compared with a structured-grid approach) is their inherent ability to discretize irregularly shaped domains with greater efficiency and less effort. Hence, this approach is ideally suited for geometrically complex configurations of practical interest. In this work the nonlinear Euler equations are solved using an upwind, cell-centered, finite-volume scheme. The discrete, linearized systems which result from this scheme are solved iteratively by a preconditioned conjugate-gradient-like algorithm known as GMRES for the two-dimensional geometry and a Gauss-Seidel algorithm for the three-dimensional; similar procedures are used to solve the accompanying linear aerodynamic sensitivity equations in incremental iterative form. As shown, this particular form of the sensitivity equation makes large-scale gradient-based aerodynamic optimization possible by taking advantage of memory efficient methods to construct exact Jacobian matrix-vector products. Simple parameterization techniques are utilized for demonstrative purposes. Once the surface has been deformed, the unstructured grid is adapted by considering the mesh as a system of interconnected springs. Grid sensitivities are obtained by differentiating the surface parameterization and the grid adaptation algorithms with ADIFOR (which is an advanced automatic-differentiation software tool). To demonstrate the ability of this procedure to analyze and design complex configurations of practical interest, the sensitivity analysis and shape optimization has been performed for a two-dimensional high-lift multielement airfoil and for a three-dimensional Boeing 747-200 aircraft.

Taylor, Arthur C., III↗

NASA NTRS2014

Wing Configuration Impact on Design Optimums for a Subsonic Passenger Transport

This study sought to compare four aircraft wing configurations at a conceptual level using a multi-disciplinary optimization (MDO) process. The MDO framework used was created by Georgia Institute of Technology and Virginia Polytechnic Institute and State University. They created a multi-disciplinary design and optimization environment that could capture the unique features of the truss-braced wing (TBW) configuration. The four wing configurations selected for the study were a low wing cantilever installation, a high wing cantilever, a strut-braced wing, and a single jury TBW. The mission that was used for this study was a 160 passenger transport aircraft with a design range of 2,875 nautical miles at the design payload, flown at a cruise Mach number of 0.78. This paper includes discussion and optimization results for multiple design objectives. Five design objectives were chosen to illustrate the impact of selected objective on the optimization result: minimum takeoff gross weight (TOGW), minimum operating empty weight, minimum block fuel weight, maximum start of cruise lift-to-drag ratio, and minimum start of cruise drag coefficient. The results show that the design objective selected will impact the characteristics of the optimized aircraft. Although minimum life cycle cost was not one of the objectives, TOGW is often used as a proxy for life cycle cost. The low wing cantilever had the lowest TOGW followed by the strut-braced wing.

Wells, Douglas P.↗

NASA NTRS1992

A hybrid approach to near-optimal launch vehicle guidance

This paper evaluates a proposed hybrid analytical/numerical approach to launch-vehicle guidance for ascent to orbit injection. The feedback-guidance approach is based on a piecewise nearly analytic zero-order solution evaluated using a collocation method. The zero-order solution is then improved through a regular perturbation analysis, wherein the neglected dynamics are corrected in the first-order term. For real-time implementation, the guidance approach requires solving a set of small dimension nonlinear algebraic equations and performing quadrature. Assessment of performance and reliability are carried out through closed-loop simulation for a vertically launched 2-stage heavy-lift capacity vehicle to a low earth orbit. The solutions are compared with optimal solutions generated from a multiple shooting code. In the example the guidance approach delivers over 99.9 percent of optimal performance and terminal constraint accuracy.

Leung, Martin S. K.↗

NASA NTRS1980

Trajectories optimization in hypersonic flight

Equations of motion were derived for the three dimensional flight of a lifting vehicles, taking into consideration all the main effects of different forces acting on a vehicle at orbital speeds. A set of equations was formulated which are valid for both the flight with lift modulation inside a planetary atmosphere and the Keplerian motion in the vacuum. The equations are independent of the physical characteristics of the vehicle. The only parameters involved are the maximum lift to drag ratio of the vehicle and a constant characterizing the atmosphere. The results obtained can be applied without modifications to any future reentry vehicle, regardless of its size, shape, and mass.

Vinh, N. X.↗

NASA NTRS1995

Optimization of an Advanced Design Three-Element Airfoil at High Reynolds Numbers

New high-lift components have been designed for a three-element advanced high-lift research airfoil using a state-of-the-art computational method. The new components were designed with the aim to provide high maximum-lift values while maintaining attached flow on the single-segment flap at approach conditions. This three-element airfoil has been tested in the NASA Langley Low-Turbulence Pressure Tunnel at chord Reynolds number up to 16 million. The performance of the NASA research airfoil is compared to a reference advanced high-lift research airfoil. Effects of Reynolds number on slat and flap rigging have been studied experimentally. The performance trend of this new high-lift design is comparable to that predicted by the computational method over much of the angle of attack range. Nevertheless, the method did not accurately predict the airfoil performance or the configuration-based trends near maximum lift.

Lin, John C.↗

NASA NTRS1975

System design of a rudder coordination system

The application of the parameter optimization computer program to the design of a rudder coordination system for the F-8 airplane is summarized. The flight condition was Mach 0.56 at 20,000 feet altitude. The system configuration selected consisted of signal paths that fed yaw rate and aileron signals to the rudder. The two signal paths were summed and then modified by a high pass filter to eliminate any steady state bias signal. The input axis of the yaw gyro was perpendicular to the aircraft zero lift line and the trim angle of attack was 7.75 degrees. The parameter optimization was used to design the complete system first, and then a root locus analysis of the individual component effects was made. The results are presented.

Whitaker, H. P.↗

NASA NTRS1988

Viscous induced drag

A fundamentally new approach to the aircraft minimum induced drag problem is presented. The method, a 'viscous lifting line', is based on the minimum entropy production principle and does not require the planar wake assumption. An approximate, closed form solution is obtained and compared with several classical results. In addition, the problem of optimizing in-plane wing sweep with constant wing root bending moment is considered. Like the classical lifting line theory, this theory predicts that induced drag is proportional to the square of the lift coefficient and inversely proportional to the wing aspect ratio. Unlike the classical theory, it predicts that in-plane wing sweep may significantly reduce induced drag, that induced drag is Reynolds number dependent, and that the optimum spanwise circulation distribution is non-elliptic.

Greene, George C.↗

NASA NTRSDate not supplied

Examination of Unified Control Approaches Incorporating Generalized Control Allocation

Transition vehicles which combine vertical take off and landing with cruise configurations pose a unique challenge for control design and implementation. For this class of vehicle, successful control designs have historically broken the flight envelope into phases and modified the control approach for each phase. This research approaches control in a unified way across the entire envelope using a robust optimal design which provides effector weighting then implemented in a generalized Affine Generalized Inverse control allocation algorithm. System performance for a Lift plus Cruise transition vehicle is presented.

unified control, robust control, optimal control, ↗

NASA NTRS1974

Optimal payload ascent trajectories of winged vehicles

A trajectory analysis is presented which shows the advantage of lifting ascent and the penalties associated with increased wing mass due to increases in aerodynamic loading. The vehicle analyzed is made up of an orbiter, an expendable liquid fuel tank, and two solid rocket motors. Results of the tradeoff are illustrated in a graph of the total vehicle mass plotted against the trajectory constraint. Results indicate that even when structural mass penalties are considered lifting ascent provides a payload delivery.

Martin, J. A.↗