Results for “Lifting” — Page 13

NASA NTRS2010

Separation of Lift-Generated Vortex Wakes Into Two Diverging Parts

As part of an ongoing study of the spreading rate of lift-generated vortex wakes, the present investigation considers possible reasons as to why segments of lift-generated wakes sometimes depart from the main part of the wake to move rapidly in either an upward or downward direction. It is assumed that deficiencies or enhancements of the lift carry over across the fuselage-shrouded wing are the driving mechanism for departures of wake-segments. The computations presented first indicate that upwardly departing wake segments that were observed and photographed could have been produced by a deficiency in lift carryover across the fuselage-shrouded part of the wing. Computations made of idealized vortex wakes indicate that upward departure of a wake segment requires a centerline reduction in the span loading of 70% or more, whether the engines are at idle or robust thrust. Similarly, it was found that downward departure of wake segments is produced when the lift over the center part of the wing is enhanced. However, it was also found that downward departures do not occur without the presence of robust engine-exhaust streams (i.e., engines must NOT be at idle). In those cases, downward departures of a wake segment occurs when the centerline value of the loading is enhanced by any amount between about 10% to 100%. Observations of condensation trails indicate that downward departure of wake segments is rare. Upward departures of wake segments appears to be more common but still rare. A study to determine the part of the aircraft that causes wake departures has not been carried out. However, even though departures of wake segments rarely occur, some aircraft do regularly shed these wake structures. If aircraft safety is to be assured to a high degree of reliability, and a solution for eliminating them is not implemented, existing guidelines for the avoidance of vortex wakes [1,3] may need to be broadened to include possible increases in wake sizes caused by vertical departures of wake segments. Further study may indicate that it is not possible to modify existing aircraft enough to prevent wake departures. Wake-avoidance guidelines must then be adjusted to provide the desired degree of safety. It appears that steps to avoid upwardly moving wake segments have already been incorporated into the avoidance procedures used for aircraft on approach to runways at the Frankfurt Airport [6,7]. The uncertainty in the prospects for compromises in flight safety caused by rapidly upwardly or downwardly moving wake segments suggest that it be specified that aircraft do not fly above or below each other during operations in the airport vicinity where aircraft are likely to be closely spaced [20].

Rossow, Vernon J.↗

NASA NTRS2012

Germanium Lift-Off Masks for Thin Metal Film Patterning

A technique has been developed for patterning thin metallic films that are, in turn, used to fabricate microelectronics circuitry and thin-film sensors. The technique uses germanium thin films as lift-off masks. This requires development of a technique to strip or undercut the germanium chemically without affecting the deposited metal. Unlike in the case of conventional polymeric lift-off masks, the substrate can be exposed to very high temperatures during processing (sputter deposition). The reason why polymeric liftoff masks cannot be exposed to very high temperatures (greater than 100 C) is because (a) they can become cross linked, making lift-off very difficult if not impossible, and (b) they can outgas nitrogen and oxygen, which then can react with the metal being deposited. Consequently, this innovation is expected to find use in the fabrication of transition edge sensors and microwave kinetic inductance detectors, which use thin superconducting films deposited at high temperature as their sensing elements. Transition edge sensors, microwave kinetic inductance detectors, and their circuitry are comprised of superconducting thin films, for example Nb and TiN. Reactive ion etching can be used to pattern these films; however, reactive ion etching also damages the underlying substrate, which is unwanted in many instances. Polymeric lift-off techniques permit thin-film patterning without any substrate damage, but they are difficult to remove and the polymer can outgas during thin-film deposition. The outgassed material can then react with the film with the consequence of altered and non-reproducible materials properties, which, in turn, is deleterious for sensors and their circuitry. The purpose of this innovation was to fabricate a germanium lift-off mask to be used for patterning thin metal films.

Brown, Ari↗

NASA NTRS1959

The Problem of Obtaining High Lift-Drag Ratios at Supersonic Speeds

The importance of the lift to drag ratio is well known to all aircraft designers since it gives, to a great extent, the aerodynamic efficiency of the airplane. Aerodynamic efficiency, however, is only one component of the grand compromise that a completed airplane represents. At subsonic speeds, lift-drag ratios of well over 200 have been measured in wind tunnels on airfoil sections; but few powered aircraft have attained (L/D) value of 20. It is invariably true that the requirements of stability and control, structure, and flight operation all contribute to reducing the design (L/D) (sub max)) considerably below those exotic values which can be predicted from unrestricted aerodynamic theory. If, however, a certain range or operating efficiency is required, there is most certainly a minimum (L/D) (sub max)) value for which the goals are just attainable. If we examine the range equation we see that range is proportional to the lift-drag ratio, the thermopropulsive efficiency, and the logarithm of the initial to final weight ratio. The appearance of the lift-drag ratio as a linear factor in the range equation indicates that every attempt should be made to increase (L/D) (sub max)); however, the search for higher (L/D)max may lead to strange and unorthodox configurations. Most frequently, such configurations are ruled out by the adverse effects of their geometry on the weight ratios. In the present paper, we will deal with the maximum lift-drag ratio problem for conventional configurations having a wing and a body in close proximity to each other. No attempt will be made to select a particular configuration as being the best. However, the promising direction to go from the aerodynamic view will be stressed with the understanding that the other factors may outweight the aerodynamics

Brown, Clinton E.↗

NASA NTRS2012

Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA)

With the very recent advent of NASA's Environmentally Responsible Aviation Project (ERA), which is dedicated to designing aircraft that will reduce the impact of aviation on the environment, there is a need for research and development of methodologies to minimize fuel burn, emissions, and reduce community noise produced by regional airliners. ERA tackles airframe technology, propulsion technology, and vehicle systems integration to meet performance objectives in the time frame for the aircraft to be at a Technology Readiness Level (TRL) of 4-6 by the year of 2020 (deemed N+2). The proceeding project that investigated similar goals to ERA was NASA's Subsonic Fixed Wing (SFW). SFW focused on conducting research to improve prediction methods and technologies that will produce lower noise, lower emissions, and higher performing subsonic aircraft for the Next Generation Air Transportation System. The work provided in this investigation was a NASA Research Announcement (NRA) contract #NNL07AA55C funded by Subsonic Fixed Wing. The project started in 2007 with a specific goal of conducting a large-scale wind tunnel test along with the development of new and improved predictive codes for the advanced powered-lift concepts. Many of the predictive codes were incorporated to refine the wind tunnel model outer mold line design. The large scale wind tunnel test goal was to investigate powered lift technologies and provide an experimental database to validate current and future modeling techniques. Powered-lift concepts investigated were Circulation Control (CC) wing in conjunction with over-the-wing mounted engines to entrain the exhaust to further increase the lift generated by CC technologies alone. The NRA was a five-year effort; during the first year the objective was to select and refine CESTOL concepts and then to complete a preliminary design of a large-scale wind tunnel model for the large scale test. During the second, third, and fourth years the large-scale wind tunnel model design would be completed, manufactured, and calibrated. During the fifth year the large scale wind tunnel test was conducted. This technical memo will describe all phases of the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) project and provide a brief summary of the background and modeling efforts involved in the NRA. The conceptual designs considered for this project and the decision process for the selected configuration adapted for a wind tunnel model will be briefly discussed. The internal configuration of AMELIA, and the internal measurements chosen in order to satisfy the requirements of obtaining a database of experimental data to be used for future computational model validations. The external experimental techniques that were employed during the test, along with the large-scale wind tunnel test facility are covered in great detail. Experimental measurements in the database include forces and moments, and surface pressure distributions, local skin friction measurements, boundary and shear layer velocity profiles, far-field acoustic data and noise signatures from turbofan propulsion simulators. Results and discussion of the circulation control performance, over-the-wing mounted engines, and the combined performance are also discussed in great detail.

Subsonic Fixed Wing↗

NASA NTRS2016

Aircraft High-Lift Aerodynamic Analysis Using a Surface-Vorticity Solver

This study extends an existing semi-empirical approach to high-lift analysis by examining its effectiveness for use with a three-dimensional aerodynamic analysis method. The aircraft high-lift geometry is modeled in Vehicle Sketch Pad (OpenVSP) using a newly-developed set of techniques for building a three-dimensional model of the high-lift geometry, and for controlling flap deflections using scripted parameter linking. Analysis of the low-speed aerodynamics is performed in FlightStream, a novel surface-vorticity solver that is expected to be substantially more robust and stable compared to pressure-based potential-flow solvers and less sensitive to surface perturbations. The calculated lift curve and drag polar are modified by an empirical lift-effectiveness factor that takes into account the effects of viscosity that are not captured in the potential-flow solution. Analysis results are validated against wind-tunnel data for The Energy-Efficient Transport AR12 low-speed wind-tunnel model, a 12-foot, full-span aircraft configuration with a supercritical wing, full-span slats, and part-span double-slotted flaps.

Olson, Erik D.↗

NASA NTRS2016

A Simple Method for High-Lift Propeller Conceptual Design

In this paper, we present a simple method for designing propellers that are placed upstream of the leading edge of a wing in order to augment lift. Because the primary purpose of these "high-lift propellers" is to increase lift rather than produce thrust, these props are best viewed as a form of high-lift device; consequently, they should be designed differently than traditional propellers. We present a theory that describes how these props can be designed to provide a relatively uniform axial velocity increase, which is hypothesized to be advantageous for lift augmentation based on a literature survey. Computational modeling indicates that such propellers can generate the same average induced axial velocity while consuming less power and producing less thrust than conventional propeller designs. For an example problem based on specifications for NASA's Scalable Convergent Electric Propulsion Technology and Operations Research (SCEPTOR) flight demonstrator, a propeller designed with the new method requires approximately 15% less power and produces approximately 11% less thrust than one designed for minimum induced loss. Higher-order modeling and/or wind tunnel testing are needed to verify the predicted performance.

Patterson, Michael↗

NASA NTRS2016

High-Lift Propeller System Configuration Selection for NASA's SCEPTOR Distributed Electric Propulsion Flight Demonstrator

Although the primary function of propellers is typically to produce thrust, aircraft equipped with distributed electric propulsion (DEP) may utilize propellers whose main purpose is to act as a form of high-lift device. These \high-lift propellers" can be placed upstream of wing such that, when the higher-velocity ow in the propellers' slipstreams interacts with the wing, the lift is increased. This technique is a main design feature of a new NASA advanced design project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR). The goal of the SCEPTOR project is design, build, and y a DEP aircraft to demonstrate that such an aircraft can be much more ecient than conventional designs. This paper provides details into the high-lift propeller system con guration selection for the SCEPTOR ight demonstrator. The methods used in the high-lift propeller system conceptual design and the tradeo s considered in selecting the number of propellers are discussed.

Patterson, Michael D.↗

NASA NTRS2017

Development of an Active Flow Control Technique for an Airplane High-Lift Configuration

This study focuses on Active Flow Control methods used in conjunction with airplane high-lift systems. The project is motivated by the simplified high-lift system, which offers enhanced airplane performance compared to conventional high-lift systems. Computational simulations are used to guide the implementation of preferred flow control methods, which require a fluidic supply. It is first demonstrated that flow control applied to a high-lift configuration that consists of simple hinge flaps is capable of attaining the performance of the conventional high-lift counterpart. A set of flow control techniques has been subsequently considered to identify promising candidates, where the central requirement is that the mass flow for actuation has to be within available resources onboard. The flow control methods are based on constant blowing, fluidic oscillators, and traverse actuation. The simulations indicate that the traverse actuation offers a substantial reduction in required mass flow, and it is especially effective when the frequency of actuation is consistent with the characteristic time scale of the flow.

Shmilovich, Arvin↗

NASA NTRS2017

Nonlinear Large Deflection Theory with Modified Aeroelastic Lifting Line Aerodynamics for a High Aspect Ratio Flexible Wing

This paper investigates the effect of nonlinear large deflection bending on the aerodynamic performance of a high aspect ratio flexible wing. A set of nonlinear static aeroelastic equations are derived for the large bending deflection of a high aspect ratio wing structure. An analysis is conducted to compare the nonlinear bending theory with the linear bending theory. The results show that the nonlinear bending theory is length-preserving whereas the linear bending theory causes a non-physical effect of lengthening the wing structure under the no axial load condition. A modified lifting line theory is developed to compute the lift and drag coefficients of a wing structure undergoing a large bending deflection. The lift and drag coefficients are more accurately estimated by the nonlinear bending theory due to its length-preserving property. The nonlinear bending theory yields lower lift and span efficiency than the linear bending theory. A coupled aerodynamic-nonlinear finite element model is developed to implement the nonlinear bending theory for a Common Research Model (CRM) flexible wing wind tunnel model to be tested in the University of Washington Aeronautical Laboratory (UWAL). The structural stiffness of the model is designed to give about 10% wing tip deflection which is large enough that could cause the nonlinear deflection effect to become significant. The computational results show that the nonlinear bending theory yields slightly less lift than the linear bending theory for this wind tunnel model. As a result, the linear bending theory is deemed adequate for the CRM wind tunnel model.

Aeroelasticity↗

NASA NTRSDate not supplied

Exploring the Potential of Hydrogen as a Lift Gas for Nasa’s Scientific Balloon Program

The United States National Aeronautics and Space Administration (NASA) Balloon Program has a rich history of conducting scientific research in the stratosphere, offering a unique platform for experiments in the near-space environment. One critical component of these high-altitude balloons is the choice of lift gas, which is pivotal to achieving the desired altitude and, thus, mission objectives. Traditionally, helium has been the preferred lift gas due to its inert properties and safety considerations. However, the increasing demand and limited global helium reserves have prompted NASA to explore alternative lift gases, with hydrogen emerging as the most logical choice. Hydrogen boasts several advantages, including its abundant availability, cost-effectiveness, and enhanced lift capability compared to helium. Moreover, it can support a wide range of scientific payloads, enabling extended mission durations and increased payload capacities, ultimately strengthening the program’s scientific potential. However, adopting hydrogen as a lift gas is not without challenges. Safety concerns, especially during the launch and recovery phases, are paramount. NASA and the other major players in the scientific ballooning community have been developing stringent safety protocols and engineering solutions to mitigate these risks. This development includes specialized support systems, leak detection mechanisms, and enhanced launch and recovery procedures. Additionally, environmental considerations must be carefully evaluated. Hydrogen release has the potential to increase concentrations of various greenhouse gases, and its usage must be balanced against the benefits it offers to scientific research and exploration. This paper delves into the ongoing research and development efforts to ensure balloon-based research’s long-term sustainability and its ability to continue pushing the boundaries of scientific discovery. This research demonstrates NASA’s commitment to innovation, safety, and environmental responsibility while maintaining its mission to advance our understanding of the Earth and the cosmos.

balloon↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Lift-to-Drag↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Wind tunnel test↗

NASA NTRS1946

Effect of Mach and Reynolds Numbers on Maximum Lift Coefficient

A knowledge of the effects of Mach and Reynolds numbers on the maximum lift coefficient is becoming of greater importance as the speeds and altitudes attainable by modern airplanes continually increase. Since most maximum-lift tests conducted to date have been either at full-scale Reynolds numbers and low Mach numbers or at high Mach numbers and small Reynolds numbers, very little is known about the inter-related effects of these two parameters on the maximum lift coefficient. In order to obtain quantitative information on these effects, flight tests were conducted at Ames Aeronautical Laboratory on six airplanes, three having NACA conventional airfoil sections, two having NACA low-drag sections, and the sixth having a North American Aviation - NACA compromise low-drag section. The results of these tests which cover a range of Mach numbers from 0.15 to 0.72 and of Reynolds numbers from 4,400,000 to 19,500,000 are assembled, together with a considerable quantity of pertinent wind-tunnel data, and analyzed in the present report. From this analysis, general conclusions have been reached indicating the manner in which the maximum lift coefficient is influenced by variations of Mach and Reynolds numbers.

AIRPLANES - BELL P-63A (AMER ) FLIGHT TESTS↗

NASA NTRS1955

Lift on a bent, flat plate

The lift on a bent, flat plate is calculated exactly by the use of conformal mapping. Results are presented in terms permitting direct determination of the angle of zero lift, the lift coefficient, and the lift-curve slope for any flap-chord ratio, flap-deflection angle, and angle of attack.

WING FLAPS - DEFLECTION↗

NASA NTRS2018

LAVA Simulations for the 3rd AIAA CFD High Lift Prediction Workshop with Body Fitted Grids

In response to the 3rd AIAA CFD High Lift Prediction Workshop, the workshop cases were analyzed using Reynolds-averaged Navier-Stokes flow solvers within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework. For the workshop cases the advantages and limitations of both overset-structured an unstructured polyhedral meshes were assessed. The workshop included 3 cases: a 2D airfoil validation case, a mesh convergence study using the High Lift Common Research Model, and a nacelle/pylon integration study using the JAXA (Japan Aerospace Exploration Agency) Standard Model. The 2D airfoil case from the workshop is used to verify the implementation of the Spalart-Allmaras turbulence model along with some of its variants within the solver. The High Lift Common Research Model case is used to assess solver performance and accuracy at varying mesh resolutions, as well as identify the minimum mesh fidelity required for LAVA on this class of problem. The JAXA Standard Model case is used to assess the solver's sensitivity to the turbulence model and to compare the structured and unstructured mesh paradigms. These workshop cases have helped establish best practices for high lift flow configurations for the LAVA solver.

LAVA↗

NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations for High-Lift Configurations using FUN3D

Wall-modeled large-eddy simulation (WMLES) capability has recently been implemented into FUN3D, an unstructured, node-centered, finite-volume solver developed at the NASA Langley Research Center. In this paper, WMLES is assessed for two configurations that are representative for high-lift applications. The first configuration is a nominal two-dimensional multielement airfoil that has been extensively studied in the literature. WMLES solutions are computed for four angles of attack and compared with previously reported solutions. Good agreement of integrated forces, surface pressures, and boundary-layer velocity profiles is shown with available experimental data especially at lower angles of attack. WMLES solutions are also computed for the NASA High-Lift Common Research Model over a large range of angles of attack. Forces, pitching moments, and pressure distributions are favorably compared with the experimental data up to the maximum lift, including the angle of attack where the maximum lift is obtained experimentally. Eddy visualization techniques of q-criterion and density-gradient magnitude illustrate the resolved content.

High-Lift flows↗

NASA NTRSDate not supplied

Mixed-element USM3D Contributions to the 4th AIAA High-Lift Prediction Workshop

This paper discusses results of the mixed-element USM3D (USM3D-ME) simulations performed for the 4th AIAA High-Lift Prediction Workshop. The workshop was separated into six Technical Focus Groups to investigate the impact of geometry modeling, grid, and computational methods for predicting high lift flows. This work was performed under the Fixed Grid RANS Technical Focus Group. The primary geometry selected for the workshop was the High-Lift Common Research Model. The performed simulations included a flap deflection study and both a grid refinement study and pitch sweep for the nominal flap deflection configuration. The results show that USM3D-ME RANS solutions, generally, tends to underpredict the lift coefficient and to predict a less negative pitching moment relative to the experimental data. The predicted drag coefficient values agree better with experiment for smaller angles of attack but were observed to be larger than experiment for the largest angle of attack simulated. The results of the grid refinement study demonstrated a lack of grid convergence for the provided grid family. The results of the grid refinement study are consistent with the submissions to the Fixed Grid and Mesh Adaptation Technical Focus Groups. Grid convergence for the provided grid family remains elusive for the international community. A 2D Multielement Airfoil configuration was included to enable a turbulence model verification study, which illustrated favorable agreement between USM3D-ME and the solutions provided by other flow solvers.

CFD↗

NASA NTRSDate not supplied

Mixed-Element USM3D Contributions to the 4th AIAA High-Lift Prediction Workshop

This paper discusses results of the mixed-element USM3D (USM3D-ME) simulations performed for the 4th AIAA High-Lift Prediction Workshop. The workshop was separated into six Technical Focus Groups to investigate the impact of geometry modeling, grid, and computational methods for predicting high lift flows. This work was performed under the Fixed Grid RANS Technical Focus Group. The primary geometry selected for the workshop was the High-Lift Common Research Model. The performed simulations included a flap deflection study and both a grid refinement study and pitch sweep for the nominal flap deflection configuration. The results show that USM3D-ME RANS solutions, generally, tends to underpredict the lift coefficient and to predict a less negative pitching moment relative to the experimental data. The predicted drag coefficient values agree better with experiment for smaller angles of attack but were observed to be larger than experiment for the largest angle of attack simulated. The results of the grid refinement study demonstrated a lack of grid convergence for the provided grid family. The results of the grid refinement study are consistent with the submissions to the Fixed Grid and Mesh Adaptation Technical Focus Groups. Grid convergence for the provided grid family remains elusive for the international community. A 2D Multielement Airfoil configuration was included to enable a turbulence model verification study, which illustrated favorable agreement between USM3D-ME and the solutions provided by other flow solvers.

CFD↗