Search NASA⌕ Search

SEARCH · Search NASA

Results for “MASS FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Nonparallel instability of supersonic and hypersonic boundary layers

Multiple scaling technique is used to examine the nonparallel instability of supersonic and hypersonic boundary-layer flows to three-dimensional (first mode) and two-dimensional (second mode) disturbances. The method is applied to the flat plate boundary layer for a range of Mach numbers from 0 to 10. Growth rates of disturbances are calculated based on three different criteria: following the maximum of the mass-flow disturbance, using an integral of the disturbance kinetic energy, and using an integral of the square of the mass-flow amplitude. By following the maximum of the mass-flow dusturbance, the calculated nonparallel growth rates are in good quantitative agreement with the experimental results of Kendall (1967) at Mach number 4.5.

El-Hady, Nabil M.↗
NASA NTRS1991

Nonparallel instability of supersonic and hypersonic boundary layers

Multiple scaling technique is used to examine the nonparallel instability of supersonic and hypersonic boundary-layer flows to three-dimensional (first mode) and two-dimensional (second mode) disturbances. The method is applied to the flat plate boundary layer for a range of Mach numbers from 0 to 10. Growth rates of disturbances are calculated based on three different criteria: following the maximum of the mass-flow disturbance, using an integral of the disturbance kinetic energy, and using the integral of the square of the mass-flow amplitude. By following the maximum of the mass-flow disturbance, the calculated nonparallel growth rates are in good quantitative agreement with the experimental results at Mach number 4.5.

El-Hady, Nabil M.↗
NASA NTRS1985

An experimental investigation of the transverse pressure gradient associated with curved free jets in the proximity of solid boundaries

An experiment has been performed to determine the mass flow and thrust augmentation associated with the flow of a two-dimensional incompressible jet issued parallel to an adjacent offset wall. A theoretical analysis based on a linear static pressure profile across the jet exit reveals that thrust augmentation is possible only for a wall offset of less than one half of the nozzle exit width. Mass flow augmentation measurements are in reasonable agreement with the proposed theory. Augmented mass flow of over three percent is observed directly, while thrust augmentation in excess of three percent is predicted when measured values of the pressure difference across the exiting jet are supplied to the theory. Measurements of the separation cavity length are presented which complement those given by previous investigators by extending the range to small values of the ratio of the wall offset to the slot height. For large offset ratios it is found that the cavity length approaches 1.25 times the wall offset distance. The initial radius of curvature of the jet centerline is found to be substantially greater than the mean radius of curvature over the cavity length, thereby indicating that the trajectory of the jet does not follow the arc of a circle as has been previously assumed.

Lund, T. S.↗
NASA NTRS1995

Effects of highly intermittent magnetic fields and plasma flows on solar wind dynamics

Filamentary magnetic fields and intermittent mass flows with highly variant physical parameters as observed in coronal holes provide, from a theoretical point of view, natural conditions for strongly nonlinear dynamics. The presence of sheared mass flows along fine scale magnetic structures results in strong nonlinear instability, most important of which is the explosive instability. We specify the physical conditions for several different manifestations of the onset of explosive instability and its further evolution: (1) fully developed explosive instability - explosive release of the energy; (2) shock formation - stabilization of instability by small scale spatial inhomogeneities leads to formation of subsequent shocks having a number of peculiarities that is determined by the interplay of thermal and viscous losses (for example, in predominance of thermal losses the isothermal jump occurs); and (3) solitary waves - stabilization of explosive instability by nonlinear dispersion effect leads to formation of a 'gas' of solitons which are later either damped away with characteristic time and energy input or evolve to solitons with explosively growing amplitudes. Each scenario is completely determined by the physical parameters of the medium, thus producing a quite uneven distribution of energy in a coronal hole and, respectively, an uneven outward propagation of the energy flux.

Ryutova, M.↗
NASA NTRS1958

Performance of an All-internal Conical Compression Inlet with Annular Throat Bleed at Mach Number 5.0

An all-internal conical compression inlet with annular bleed at the throat was investigated at Mach 5.0 and zero angle of attack. The minimum contraction ratio of the supersonic diffuser, coincident with a mass-flow ratio of 1.0, was determined to be 0.084 as compared with the isentropic contraction ratio of 0.04 at Mach 5.0. The over-all inlet performance was very sensitive to the amount of annular bleed at the throat because of the extensive boundary layer. For example, the critical recovery varied from 41 percent with 6-percent bleed to 59 percent with 25-percent bleed. Decreasing the spacing between the supersonic and subsonic diffusers increased the critical mass-flow ratio but reduced the range of subcritical mass-flow regulation. A constant-area section was required ahead of the subsonic diffuser in order to obtain reasonable performance. An inlet-engine net-thrust analysis indicated that the optimum performance occurred with from 20- to 25-percent bleed, depending on how the bypassed air was handled.

Stitt, Leonard E.↗
NASA NTRS2003

Advances in Pneumatic-Controlled High-Lift Systems Through Pulsed Blowing

Circulation Control technologies have been around for 65 years, and have been successfully demonstrated in laboratories and flight vehicles alike. Yet there are few production aircraft flying today that implement these advances. Circulation Control techniques may have been overlooked due to perceived unfavorable trade offs of mass flow, pitching moment, cruise drag, noise, etc. Improvements in certain aspects of Circulation Control technology are the focus of this paper. This report will describe airfoil and blown high lift concepts that also address cruise drag reduction and reductions in mass flow through the use of pulsed pneumatic blowing on a Coanda surface. Pulsed concepts demonstrate significant reductions in mass flow requirements for Circulation Control, as well as cruise drag concepts that equal or exceed conventional airfoil systems.

Jones, Gregory S.↗
NASA NTRS2005

Pneumatic Flap Performance for a 2D Circulation Control Airfoil, Steady and Pulsed

Circulation Control technologies have been around for 65 years, and have been successfully demonstrated in laboratories and flight vehicles alike, yet there are few production aircraft flying today that implement these advances. Circulation Control techniques may have been overlooked due to perceived unfavorable trade offs of mass flow, pitching moment, cruise drag, noise, etc. Improvements in certain aspects of Circulation Control technology are the focus of this paper. This report will describe airfoil and blown high lift concepts that also address cruise drag reduction and reductions in mass flow through the use of pulsed pneumatic blowing on a Coanda surface. Pulsed concepts demonstrate significant reductions in mass flow requirements cor Circulation Control, as well as cruise drag concepts that equal or exceed conventional airfoil systems.

Jones, Gregory S.↗
NASA NTRS1973

Local flow measurements at the inlet spike tip of a Mach 3 supersonic cruise airplane

The flow field at the left inlet spike tip of a YF-12A airplane was examined using at 26 deg included angle conical flow sensor to obtain measurements at free-stream Mach numbers from 1.6 to 3.0. Local flow angularity, Mach number, impact pressure, and mass flow were determined and compared with free-stream values. Local flow changes occurred at the same time as free-stream changes. The local flow usually approached the spike centerline from the upper outboard side because of spike cant and toe-in. Free-stream Mach number influenced the local flow angularity; as Mach number increased above 2.2, local angle of attack increased and local sideslip angle decreased. Local Mach number was generally 3 percent less than free-stream Mach number. Impact-pressure ratio and mass flow ratio increased as free-stream Mach number increased above 2.2, indicating a beneficial forebody compression effect. No degradation of the spike tip instrumentation was observed after more than 40 flights in the high-speed thermal environment encountered by the airplane. The sensor is rugged, simple, and sensitive to small flow changes. It can provide accurate imputs necessary to control an inlet.

Johnson, H. J.↗
NASA NTRS2001

Active Control of Rotating Stall Demonstrated for a Multistage Compressor With Inlet Distortion

Aircraft compressors can suffer debilitating consequences as a result of rotating stall and surge events caused by inlet distortions. This is particularly true of aircraft during takeoff, when the compressor is operating at peak performance close to the surge line. Significant research has been conducted by the NASA Glenn Research Center in the area of compressor stability enhancement through active and passive control methods. Most recently, an experiment was conducted at the Wright Patterson Air Force Base Research Laboratory on a two-stage fan with inlet guide vanes and inlet distortion. In this joint Small Business Innovation Research effort between Scientific Systems and Glenn, control of rotating stall was demonstrated in a multistage transonic fan. This twostage fan with inlet guide vanes was tested under clean and distorted inlet conditions. The compressor was also configured with a circumferential distortion screen capable of 180 of distortion and with 14 high-velocity injectors upstream of the first rotor. Twelve of these injectors could oscillate up to frequencies of 450 Hz. The additional two injectors were located next to each other and were used in concert with each other as a single, on/off, high-authority actuator. In a first test of injection in this multistage environment, 12 of the valves were opened 50 percent of their full stroke to assess steady injection through the compressor. This baseline injection is shown in the compressor characteristic of the following figure, and stall margin improvements are tracked from this baseline condition. The compressor was then tested with clean inlet conditions using 12 injectors and active control. Pressure disturbances were tracked before rotating stall, and a constant gain control scheme reduced the stalling mass flow by 10.8 percent over the baseline. With the distortion screen present in the inlet, a pole-zero cancellation control scheme was used to achieve a 6.4-percent decrease in stalling mass flow. These improvements also are shown in the figure. In a final experiment, actively controlled, high-frequency injection from the 12 valves was used in conjunction with the high-authority actuators. In this test, the stalling mass flow of the compressor was reduced by 27 percent as indicated in the graph. These results were obtained by injecting less than 2 percent of the total compressor throughflow into the rotor tip region via 14 injection ports. These results mark the first successful demonstration of actively controlled air injection as a stall-control strategy for multistage compressors operating at speeds typical of an actual gas turbine engine. A goal of continuing research is to determine the combination of air-injection parameters and control strategies that are most effective in providing stall control for both clean and distorted inlet flow conditions for multistage environments. Other goals include the demonstration of stall control at many locations along the core compressor and development and application of active stall control strategies that will be integral flightworthy components of onboard engine hardware.

VanSchalkwyk, Christian↗
NASA NTRS1993

Time-Accurate Unsteady Flow Simulations Supporting the SRM T+68-Second Pressure Spike Anomaly Investigation (STS-54B)

Time-accurate unsteady flow simulations are being performed supporting the SRM T+68sec pressure 'spike' anomaly investigation. The anomaly occurred in the RH SRM during the STS-54 flight (STS-54B) but not in the LH SRM (STS-54A) causing a momentary thrust mismatch approaching the allowable limit at that time into the flight. Full-motor internal flow simulations using the USA-2D axisymmetric code are in progress for the nominal propellant burn-back geometry and flow conditions at T+68-sec--Pc = 630 psi, gamma = 1.1381, T(sub c) = 6200 R, perfect gas without aluminum particulate. In a cooperative effort with other investigation team members, CFD-derived pressure loading on the NBR and castable inhibitors was used iteratively to obtain nominal deformed geometry of each inhibitor, and the deformed (bent back) inhibitor geometry was entered into this model. Deformed geometry was computed using structural finite-element models. A solution for the unsteady flow has been obtained for the nominal flow conditions (existing prior to the occurrence of the anomaly) showing sustained standing pressure oscillations at nominally 14.5 Hz in the motor IL acoustic mode that flight and static test data confirm to be normally present at this time. Average mass flow discharged from the nozzle was confirmed to be the nominal expected (9550 lbm/sec). The local inlet boundary condition is being perturbed at the location of the presumed reconstructed anomaly as identified by interior ballistics performance specialist team members. A time variation in local mass flow is used to simulate sudden increase in burning area due to localized propellant grain cracks. The solution will proceed to develop a pressure rise (proportional to total mass flow rate change squared). The volume-filling time constant (equivalent to 0.5 Hz) comes into play in shaping the rise rate of the developing pressure 'spike' as it propagates at the speed of sound in both directions to the motor head end and nozzle. The objectives of the present analysis are to: (1) capture the dynamic responses of the motor combustion gas flow to correlate with available low-frequency (less than 12.5 sample/sec) data and (2) observe the high-frequency (up to 50 Hz) characteristics of the response to determine any potentials for dynamic coupling.

Dougherty, N. S.↗
NASA NTRS1936

Effect of Several Factors on the Cooling of a Radial Engine in Flight

Flight tests of a Grumman Scout (XSF-2) airplane fitted with a Pratt & Whitney 1535 supercharged engine were conducted to determine the effect of engine power, mass flow of the cooling air, and atmospheric temperature on cylinder temperature. The tests indicated that the difference in temperature between the cylinder wall and the cooling air varied as the 0.38 power of the brake horsepower for a constant mass flow of cooling air, cooling-air temperature, engine speed, and brake fuel consumption. The difference in temperature was also found to vary inversely as the 0.39 power of the mass flow for points on the head and the 0.35 power for points on the barrel, provided that engine power, engine speed, brake fuel consumption, and cooling-air temperature were kept constant. The results of the tests of the effect of atmospheric temperature on cylinder temperature were inconclusive owing to unfavorable weather conditions prevailing at the time of the tests. The method used for controlling the test conditions, however, was found to be feasible.

Schey, Oscar W↗
NASA NTRS1979

Scaling characteristics of MPD propulsion

Experiments in which a high-power, quasi-steady MPD thruster is scaled down by a factor of two indicate that the key features of MPD thruster operation are replicated in the smaller version. Voltage-current data over a 24:1 mass flow range show that the ablation onset parameter is constant for each thruster, although the constant is not the same. Time-integrated photographs of the discharge radiance reveal strikingly similar features at scaled values of current and mass flow. The measured terminal properties of the half-scale thruster are similar to the full-scale thruster, but the regime of operation is smaller and generally less efficient, except within a restricted range of arc current and mass flow.

Mead, F. B., Jr.↗
NASA NTRS1984

Large amplitude forcing of a high speed 2-dimensional jet

The effect of large amplitude forcing on the growth of a high speed two dimensional jet was investigated experimentally. Two forcing techniques were utilized: mass flow oscillations and a mechanical system. The mass flow oscillation tests were conducted at Strouhal numbers from 0.00052 to 0.045, and peak to peak amplitudes up to 50 percent of the mean exit velocity. The exit Mach number was varied in the range 0.15 to 0.8. The corresponding Reynolds numbers were 8,400 and 45,000. The results indicate no significant change of the jet growth rate or centerline velocity decay compared to the undisturbed free jet. The mechanical forcing system consists of two counter rotating hexagonal cylinders located parallel to the span of the nozzle. Forcing frequencies up to 1,500 Hz were tested. Both symmetric and antisymmetric forcing can be implemented. The results for antisymmetric forcing showed a significant (75 percent) increase of the jet growth rate at an exit Mach number of 0.25 and a Strouhal number of 0.019. At higher rotational speeds, the jet deflected laterally. A deflection angle of 39 deg with respect to the centerline was measured at the maximum rotational speed.

Bernal, L.↗
NASA NTRS1992

Analysis of the Cosmic Background Explorer (COBE) helium venting through effects on the orbit

An analysis is described which shows that a helium venting thrust level that is 60 percent higher than the predicted 2.3 millinewtons may be the cause of the unusually high premission-analysis and on-orbit support orbital decay rates and drag correction factors found for the Cosmic Background Explorer satellite. Depletion of the helium allowed a determination of the average mass flow rate and specific impulse. The average mass flow rate of 3.3 mg/sec confirmed the thrust levels indicated by the venting thrust analysis. Liquid helium is used for cooling instruments aboard the satellite.

Cox, C. M.↗
NASA NTRS1992

Full Navier-Stokes calculations on the installed F/A-18 inlet at a high angle of attack

Major objectives of the NASA High-Alpha Technology Program are the accurate prediction of the internal (inlet) aerodynamics of an aircraft operating at attitudes of up to 60 deg pitch and 10 deg yaw and the calibration of CFD codes for predicting the internal performance of inlets. Numerical results are presented for the three cases of a full-scale model, a 20-percent scale model at design mass flow, and a scale model at reduced mass flow; attention is given to the effects of Reynolds number. All three cases are at 30 deg angle of attack and zero deg yaw. The results thus obtained are helpful to experimentalists in determining some of their instrumentation requirements.

Bruns, James E.↗
NASA NTRS2008

Impact of Azimuthally Controlled Fluidic Chevrons on Jet Noise

The impact of azimuthally controlled air injection on broadband shock noise and mixing noise for single and dual stream jets was investigated. The single stream experiments focused on noise reduction for low supersonic jet exhausts. Dual stream experiments included high subsonic core and fan conditions and supersonic fan conditions with transonic core conditions. For the dual stream experiments, air was injected into the core stream. Significant reductions in broadband shock noise were achieved in a single jet with an injection mass flow equal to 1.2% of the core mass flow. Injection near the pylon produced greater broadband shock noise reductions than injection at other locations around the nozzle periphery. Air injection into the core stream did not result in broadband shock noise reduction in dual stream jets. Fluidic injection resulted in some mixing noise reductions for both the single and dual stream jets. For subsonic fan and core conditions, the lowest noise levels were obtained when injecting on the side of the nozzle closest to the microphone axis.

Henderson, Brenda S.↗
NASA NTRS1994

Ethylene Trace-gas Techniques for High-speed Flows

Three applications of the ethylene trace-gas technique to high-speed flows are described: flow-field tracking, air-to-air mixing, and bleed mass-flow measurement. The technique involves injecting a non-reacting gas (ethylene) into the flow field and measuring the concentration distribution in a downstream plane. From the distributions, information about flow development, mixing, and mass-flow rates can be dtermined. The trace-gas apparatus and special considerations for use in high-speed flow are discussed. A description of each application, including uncertainty estimates is followed by a demonstrative example.

Davis, David O.↗
NASA NTRSDate not supplied

Model Preparation Areas for Propulsion Airframe Integration Testing at NASA Langley Research Center

Currently there are three major NASA Langley facilities that perform PAI testing. These include the National Transonic Facility, the 14’x22’ Low Speed Wind tunnel, and the Unitary Plan Wind Tunnel. While each of these facilities have their own model preparation areas, the model preparation area located at the NTF complex that focuses on blowing systems with high mass flow requirements support all of the LaRC facilities. The application of a Propulsion Airframe Integration requires special attention to the air delivery system interaction with the model. These interactions typically focus on the tares across the balance associated with inlet and nozzle performance which are related to the mass flow through the system and the efficiency of the inlet and nozzle geometries. While this paper does not characterize any specific propulsion system, it does focus on the mass flow and pressures requirement needed for pretesting such systems prior to wind tunnel installation. Weight flow boundaries for the air delivery system were identified to range from 0.1 to 20 lbm/sec.

Model Preparation Area↗