Heat Deposition Analysis of Target Materials in the High Flux Isotope Reactor for HEU and LEU Cores
Explore the source record for details and available documents.
Burg, Kevin↗
SEARCH · Search NASA
Results for “MATERIALS - TEMPERATURES, HIGH”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Material Plasma Exposure eXperiment High Heat Flux Microwave Absorber Design, Manufacture, and Articles Test
The Material Plasma Exposure eXperiment (MPEX) at Oak Ridge National Laboratory is in the final design phase. MPEX will be capable of exposing neutron-irradiated materials to plasmas for the study of plasma-material interaction. This facility will provide information about the complex effects of plasmas on materials and contribute to examining new materials that can withstand high heat fluxes and high ion fluences for future fusion devices. MPEX plasma is heated by 70-GHz or 105-GHz electron Bernstein wave/electron cyclotron heating (ECH), and the high-frequency microwaves are prone to scattering microwave power, which can have detrimental effects, especially on diagnostic components. A large portion of the injected ECH power is expected to be absorbed by plasma, but the remainder requires that microwave absorbers be placed immediately upstream and downstream of the ECH launcher to minimize stray microwaves leaving the ECH region. These microwaves can inadvertently heat components that cannot be shielded or otherwise protected. The microwave absorber design is based on an array of pyramid-shaped ceramic tiles brazed to a water-cooled explosion-bonded heat sink and a stainless steel plate to produce one tile module. Computational fluid dynamics and structural analyses were performed to optimize and validate the design. Multiple test coupons were produced to validate the process for brazing the two different tile materials to the Glidcop AL-15 baseplate. The articles were tested to evaluate the reliability and thermal performance through exposure to an electron beam with a heat flux of up to 1.5 MW/m2. Nondestructive testing was performed before and after testing to identify voids or separations that may have been introduced by the high heat flux. This paper discusses the details of high heat flux microwave absorber design, manufacturing details and associated challenges, and test results, demonstrating the effectiveness of the proposed design.
Hussain, Aftab↗
Harnessing Quantum Computing for Energy Materials: Opportunities and Challenges
Developing high-performance materials is critical for diverse energy applications to increase efficiency, improve sustainability and reduce costs. Classical computational methods have enabled important breakthroughs in energy materials development, but they face scaling and time-complexity limitations, particularly for high-dimensional or strongly correlated material systems. Quantum computing (QC) promises to offer a paradigm shift by exploiting quantum bits with their superposition and entanglement to address challenging problems intractable for classical approaches. This Perspective discusses the opportunities in leveraging QC to advance energy materials research and the challenges QC faces in solving complex and high-dimensional problems. We present cases on how QC, when combined with classical computing methods, can be used for the design and simulation of practical energy materials. We also outline the outlook for error-corrected, fault-tolerant QC capable of achieving predictive accuracy and quantum advantage for complex material systems.
Algorithms↗
High Velocity Joining of Multi-material Stacks Containing 3rd Generation Advanced High-Strength Stainless Steel and Aluminum Extrusion and Casting (Abstract)
Advanced lightweight materials, including multi-phase steels, aluminum extrusions and aluminum castings, have increasingly replaced mild steel to meet original equipment manufacturer (OEM) demand for increased fuel economy and crash-safety requirements. Third Generation (Gen 3) AHSS provides a superior combination of strength and ductility for crash energy management components in the vehicle body-in-white (BIW). Aluminum extrusions are widely used for bumper, door rocker panel, cradle and battery frame applications. Aluminum castings are increasingly being used in electric vehicles to provide part consolidation, weight saving and increased driving range. Rocker panels are, for example, an important component of the battery electric vehicle (BEV) body structure. The rocker panel serves several purposes, including structural support, crash resistance, protection for the vehicle's underbody and battery tray, and contributing to the overall aesthetics. In order to reduce weight, rocker panels are usually constructed using outer panels consisting of 3rd generation advanced high strength steels (AHSS) and an inner multicell aluminum extrusion structure for energy absorption which protects the batteries in a crash event. It is well known, however, that these material combinations provide significant challenges for joining and are susceptible to liquid metal embrittlement and loss of strength. The overall goal is to find a solution that addresses these challenges in order to produce multi-material vehicle components with reduced weight and minimal galvanic and recyclability issues. The approach being proposed here is to utilize a novel high velocity (HiVe) riveting and clinching technique recently demonstrated by Pacific Northwest National Laboratory (PNNL) to join (2T/3T) sheets of aluminum alloys and steel. This process will not only address the aforementioned challenges but also help significantly reduce the joining cycle time. This work will also demonstrate use of HiVe assemblies to be retrofitted to existing body-shop robots thus having minimal impact to existing body shop operations.
36 MATERIALS SCIENCE↗
Computational and experimental search for potential polyanionic K-ion cathode materials
Discovering high-energy cathode materials is critical to construct K-ion batteries for practical applications. Owing to the great success of layered oxides in Li- and Na-ion systems, K layered cathodes have also been investigated in recent years. However, the much larger size of K + compared to Li or Na introduces strong K + –K + interaction within the layer, which results in a sloped voltage profile thereby limiting the specific capacity and operating voltage. In contrast, polyanionic materials with a three-dimensional K + arrangement can effectively mitigate K + –K + interaction. In this work, ten K polyanionic compounds with theoretical capacity >100 mA h g –1 are screened from the Inorganic Crystal Structure Database as potential cathode materials for K-ion batteries. Among the ten proposed compounds, K 2 MnP 2 O 7 , K 2 Mn 2 P 2 O 7 F 2 , K 2 Fe 2 P 2 O 7 F 2 , and K 6 V 2 (PO 4 ) 4 with average voltage <4.5 V are synthesized and evaluated electrochemically. While the re-insertion of K into these compounds is not fully reversible, it may be related to the very high migration barrier that we compute for K ions. In addition, we show the successful synthesis of a series of K 3 V 3–x Cr x (PO 4 ) 4 (x = 0, 1, 2, 3) compounds. Among these, K 3 V 2 Cr(PO 4 ) 4 exhibits the largest reversible capacity, as revealed by the in situ investigation. Lastly, we find that the redox couples in many of these compounds sit at remarkably high potential, even higher than in equivalent Li compounds, which brings both opportunities and challenges in the future research of K polyanion cathodes.
25 ENERGY STORAGE↗
Background Information on ARPA-E's REUSE Program (White Paper)
Under the REUSE Topic, ARPA-E seeks to fund the development of technologies to convert high-energy materials currently going to landfills to a high-energy content liquid product capable of displacing energy imports used for fuel or chemical production. The high-energy materials include plastics (#1-7 polymers, rubber, and composites) and paper. As discussed below, we estimate 30-34 MM ton plastic, 2-6 MM ton rubber, 18 MM ton of paper, and up to 0.1 MM ton composites are potentially available annually for this purpose. These numbers may be conservative based on changes in the plastic and paper export markets. ARPA-E anticipates deployment of multiple low-cost, simple, flexible, small-scale (100-500 ton per day) regional facilities using modular plants. This scale is consistent with the sources for high-energy materials, which include ~300 Material Recovery Facilities and industrial waste sources. The assumption is that such facilities can be more economical than the paradigm of large-scale facilities making purity products, due to cost for transporting and aggregating waste and the high operating costs (OPEX) and capital cost (CAPEX) for product purification. This document gives a brief technical review for multiple potential process technologies. The review is not intended to be comprehensive or limiting, only to provide an introduction to potential Applicants.
10 SYNTHETIC FUELS↗
White Paper: Background Information on ARPA-E's Reuse Program
This document provides supplemental information for ARPA-E’s exploratory research program, “Recycle Underutilized Solids to Energy” (REUSE). The goal is to provide additional technical information to prospective Applicants. Further information is available in a blog interview and webinar at https://arpa-e.energy.gov/?q=news-item/trash-treasure-reuse-creates-feedstock-plastic-waste. Award information, submission requirements, evaluation criteria, and other applicable information is provided in Funding Opportunity Announcements DE-FOA-0001953 and DE-FOA-0001954 (SBIR/STTR). REUSE-specific requirements are provided in Topic K of those FOAs, and is available at https://arpa-e-foa.energy.gov/Default.aspx?Search=0001953&SearchType=#FoaIde8647d89-1cac-4b58-8622-1b04de8958c4. Under the REUSE Topic, ARPA-E seeks to fund the development of technologies to convert high-energy materials currently going to landfills to a high-energy content liquid product capable of displacing energy imports used for fuel or chemical production. The high-energy materials include plastics (#1-7 polymers, rubber, and composites) and paper. As discussed below, we estimate 30-34 MM ton plastic, 2-6 MM ton rubber, 18 MM ton of paper, and up to 0.1 MM ton composites are potentially available annually for this purpose. These numbers may be conservative based on changes in the plastic and paper export markets. ARPA-E anticipates deployment of multiple low-cost, simple, flexible, small-scale (100-500 ton per day) regional facilities using modular plants. This scale is consistent with the sources for high-energy materials, which include ~300 Material Recovery Facilities and industrial waste sources. The assumption is that such facilities can be more economical than the paradigm of large-scale facilities making purity products, due to cost for transporting and aggregating waste and the high operating costs (OPEX) and capital cost (CAPEX) for product purification. This document gives a brief technical review for multiple potential process technologies. The review is not intended to be comprehensive or limiting, only to provide an introduction to potential Applicants.
99 GENERAL AND MISCELLANEOUS↗
Hybrid BaTiO 3 /SiN x /AlGaN/GaN lateral Schottky barrier diodes with low turn-on and high breakdown performance
In this Letter, we demonstrate hybrid GaN lateral Schottky barrier diodes with enhanced breakdown characteristics and a low turn-on voltage. These diodes incorporate a lateral Schottky barrier in combination with a high permittivity material beneath the field plate, enabling high average breakdown fields and a low turn-on voltage. Average electric fields up to 2.38 MV/cm were achieved for devices with an anode–cathode spacing of 4 μm, while maintaining with a turn-on voltage of 0.48 V. In contrast, SiN x /AlGaN/GaN control lateral Schottky diodes displayed an average breakdown field of ~0.7 MV/cm for devices with similar dimensions with a turn-on voltage of 0.46 V. The use of a high-permittivity dielectric can more effectively utilize the high breakdown fields in wide bandgap materials by proper management of the electric field. This demonstration provides an innovative way to integrate high-permittivity materials with GaN lateral devices for improved breakdown and resistance characteristics.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
High-Entropy Ceramic Coatings: Transformative New Materials for Environmentally-Compatible Thin-Film Insulators against High-T Molten Salts
An emerging new class of promising materials, High-Entropy Ceramics (HECs) or Compositionally-Complex Ceramics (CCCs), have been successfully fabricated in the last three years. This project evaluates HECs/CCCs in the concentrated solar power (CSP) context. In this project, we have identified a couple of simple, and key descriptors governing thermal conductivity in HECs. Size disorder among the cations was found to have a strong influence on the thermal conductivity across multiple systems and throughout a vast compositional space. Since identifying this, we have optimized previous compositions to achieve low thermal conductivities of $k$~$1-1.4Wm{-1}K{-1}$. We have further reduced our selection of promising compositions based on project guidelines and applied a theory that can potentially predict reactivity with molten salts to identify a small set of HECs that are suitable for further molten salt heat transfer media (HTM) stability testing. Many compositions reveal poor resistance to molten chloride salt after being exposed for 24 h compared to the reference structural alloy, Haynes 230. However, after 100 h, a few HECs/CCCs show strong parabolic rate constant effects and provide greater resistance to chloride salt compared to Haynes 230 alloy, which shows more linear kinetics. Postmortem characterization of the microstructure reveals the parabolic rate constant originates from a dense reaction layer form at the interface. This feature is absent in Haynes 230, which only shows grain boundary infiltration. The HECs/CCCs were also put in contact with the metal alloy under Ar for 800 h at 800°C and show negligible interaction. Lastly, parabolic rate constant HECs/CCCs also have low thermal conductivity $(<2 Wm^{-1} K^{-1})$ at 800°C. These specimens satisfy all project requirements and demonstrate their promising application in next-generation CSP.
14 SOLAR ENERGY↗
Isotope-Specific Analysis of Neutron-Irradiated Lithium Aluminate Ceramics by Nuclear Magnetic Resonance Spectroscopy
The effects of neutron irradiation on lithium aluminate targets and the permeation of tritium into surrounding components are primary concerns in the development of materials for use in tritium production. The high specific activity and volatility of the tritium in activated samples greatly increase the challenges of experimental analysis. This paper reports the determination of the chemical forms and quantities of H-3 and Li-6 in irradiated and non-irradiated LiAlO2 by nuclear magnetic resonance (NMR) spectroscopy, and demonstrates that measurements can be performed in a non-destructive, safe manner to obtain isotope-selective, quantitative information on highly hazardous materials.
Tritium, solid state nuclear magnetic resonance sp↗
Presynthetic Redox Gated Metal-to-Insulator Transition and Photothermoelectric Properties in Nickel Tetrathiafulvalene-Tetrathiolate Coordination Polymers
Photothermoelectric (PTE) materials are promising candidates for solar energy harvesting and photodetection applications, especially for near-infrared (NIR) wavelengths. Although the processability and tunability of organic materials are highly advantageous, examples of organic PTE materials are comparatively rare and their PTE performance is typically limited by poor photothermal (PT) conversion. Here, we report the use of redox-active Sn complexes of tetrathiafulvalene-tetrathiolate (TTFtt) as transmetalating agents for the synthesis of presynthetically redox tuned NiTTFtt materials. Unlike the neutral material NiTTFtt, which exhibits n-type glassy-metallic conductivity, the reduced materials Li 1.2 Ni 0.4 [NiTTFtt] and [Li(THF) 1.5 ] 1.2 Ni 0.4 [NiTTFtt] (THF = tetrahydrofuran) display physical characteristics more consistent with p-type semiconductors. The broad spectral absorption and electrically conducting nature of these TTFtt-based materials enable highly efficient NIR-thermal conversion and good PTE performance. Furthermore, in contrast to conventional PTE composites, these NiTTFtt coordination polymers are notable as single-component PTE materials. As a result, the presynthetically tuned metal-to-insulator transition in these NiTTFtt systems directly modulates their PT and PTE properties.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A universal etching method for synthesizing high-performance single crystal cathode materials
LiNi x MnyCo 1-x-y O 2 (NMC) is considered the most appealing cathode material due to its high energy density and low cost. However, the stability and safety concerns, caused by the degradation of polycrystalline cathode materials during cycling, have restricted their practical applications. To overcome this shortcoming, converting polycrystalline cathode to high-performance single-crystal cathode materials becomes an appealing solution. In this work, a universal etching approach is firstly developed to synthesize single-crystal cathode materials. The rate performance of the obtained single-crystal NMC111 is 10–15% more than that of polycrystalline NMC111 whereas the capacity retention of single-crystal NMC111 is enhanced by ~12% after 300 cycles at 0.5C. The obtained single-crystal NMC622 exhibits a pronounced improvement in rate performance, especially at high rates (~28.6% better at 5C and ~129% better at 10C) and has a comparable cycle performance compared to polycrystalline NMC622. Altogether, the findings propose an alternative approach to generate single-crystal particles with high energy density and cycle stability for the next generation lithium-ion batteries.
25 ENERGY STORAGE↗
High-Energy Solid-State Lithium Batteries with Organic Cathode Materials (Final Report)
Organic materials made from abundant elements via low-energy processes are emerging as sustainable and low-cost alternatives to transition metal oxides as the electrode materials for high- energy batteries in the wake of supply chain and environmental issues associated with critical materials during the transition to clean energy. Organic insertion materials (OIMs) offer material- level energy comparable to transition metal oxides, but they have durability difficulties owing to dissolving in common liquid electrolytes. Combining ceramic-based solid electrolytes with organic electrode materials is one intriguing solution. The goal of this project is to design and synthesize high-energy OIMs, to understand the chemical dynamics and mechanical properties at the OIM-sulfide interface during electrochemical cycling, and to develop methods for constructing the optimum cathode microstructure, which will lead to improved electrochemical performance. The project team has accomplished the following over the last four years: (a) demonstrating that the mechanical softness of organic electrode materials is uniquely beneficial in suppressing crack formation at the electrode-electrolyte interface during cell operation; (b) understanding the interaction between cathode microstructure and the mechanical properties of individual components; and (c) establishing predictive control of cathode microstructure by tuning the mechanical properties of solid electrolytes and OIMs; (d) determining the chemical combability of sulfide electrolyte with high-energy OIMs and finally (f) laying out a road map toward a specific energy of 500 Wh kg -1 for solid-state lithium batteries. 14 publications resulted from this project.
25 ENERGY STORAGE↗
Developing reactors for electrifying bio-methanation: a perspective from bio-electrochemistry
The integration of microbial synthesis with renewable electricity is an emerging route for both CO 2 utilization and seasonal energy storage in the form of stored bio-electrofuels. The major benefits of electrifying bioreactors include: using highly selective bio-catalysts for CO 2 conversion under mild reaction conditions; decoupling the production of more facile electrochemical intermediates, such as hydrogen, at the electrode from the production of bio-catalyzed multi-electron and/or carbon products, such as methane or acetate; using microbes as robust and self-regenerating catalysts enabling higher efficiency and durability in CO 2 conversion systems compared to inorganic catalysis. In this Perspective, we propose research aimed at developing electro-bioreactor components that will increase the productivity of the reactor while maintaining high energy efficiency and biocompatible reaction conditions to fully realize the benefits of electrified bioreactors. Furthermore, these developments include: flow reactors with tailored 3D electrodes to optimally use the reactor volume, electrocatalysts designed for peak performance in neutral pH electrolytes, high conductivity microbial media, and new membrane separator materials with high ion conductivity and low gas permeability. Production of methane via a hybrid electrical-biological approach is taken as a case study to motivate these developments. Finally, an iterative design–manufacture–test cycle, enabled by additive manufacturing and 3D printing technologies, is proposed to rapidly prototype components prior to large-scale manufacturing.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Discovering tungsten-based composites as plasma facing materials for future high-duty cycle nuclear fusion reactors
Abstract Despite of excellent thermal properties and high sputtering resistance, pure tungsten cannot fully satisfy the requirements for plasma facing materials in future high-duty cycle nuclear fusion reactions due to the coupled extreme environments, including the high thermal loads, plasma exposure, and radiation damage. Here, we demonstrated that tungsten-based composite materials fabricated using spark-plasma sintering (SPS) present promising solutions to these challenges. Through the examination of two model systems, i.e., tungsten-zirconium composite for producing porous tungsten near the surface and dispersoid-strengthened tungsten, we discussed both the strengths and limitations of the SPS-fabricated materials. Our findings point towards the need for future studies aimed at optimizing the SPS process to achieve desired microstructures and effective control of oxygen impurities in the tungsten-based composite materials.
21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
Tantalum pentoxide: a new material platform for high-performance dielectric metasurface optics in the ultraviolet and visible region
Dielectric metasurfaces, composed of planar arrays of subwavelength dielectric structures that collectively mimic the operation of conventional bulk optical elements, have revolutionized the field of optics by their potential in constructing high-efficiency and multi-functional optoelectronic systems on chip. The performance of a dielectric metasurface is largely determined by its constituent material, which is highly desired to have a high refractive index, low optical loss and wide bandgap, and at the same time, be fabrication friendly. Here, we present a new material platform based on tantalum pentoxide (Ta 2 O 5 ) for implementing high-performance dielectric metasurface optics over the ultraviolet and visible spectral region. This wide-bandgap dielectric, exhibiting a high refractive index exceeding 2.1 and negligible extinction coefficient across a broad spectrum, can be easily deposited over large areas with good quality using straightforward physical vapor deposition, and patterned into high-aspect-ratio subwavelength nanostructures through commonly-available fluorine-gas-based reactive ion etching. We implement a series of high-efficiency ultraviolet and visible metasurfaces with representative light-field modulation functionalities including polarization-independent high-numerical-aperture lensing, spin-selective hologram projection, and vivid structural color generation, and the devices exhibit operational efficiencies up to 80%. Our work overcomes limitations faced by scalability of commonly-employed metasurface dielectrics and their operation into the visible and ultraviolet spectral range, and provides a novel route towards realization of high-performance, robust and foundry-manufacturable metasurface optics.
36 MATERIALS SCIENCE↗
Resolving complex intralayer transition motifs in high-Ni-content layered cathode materials for lithium-ion batteries
High-Ni-content layered materials are promising cathodes for next-generation lithium-ion batteries. However, investigating the atomic configurations of the delithiation-induced complex phase boundaries and their transitions remains challenging. Here, in this study, by using deep-learning-aided super-resolution electron microscopy, we resolve the intralayer transition motifs at complex phase boundaries in high-Ni cathodes. We reveal that an O3 → O1 transformation driven by delithiation leads to the formation of two types of O1–O3 interface, the continuous- and abrupt-transition interfaces. The interfacial misfit is accommodated by a continuous shear-transition zone and an abrupt structural unit, respectively. Atomic-scale simulations show that uneven in-plane Li+ distribution contributes to the formation of both types of interface, and the abrupt transition is energetically more favourable in a delithiated state where O1 is dominant, or when there is an uneven in-plane Li + distribution in a delithiated O3 lattice. Moreover, a twin-like motif that introduces structural units analogous to the abrupt-type O1–O3 interface is also uncovered. The structural transition motifs resolved in this study provide further understanding of shear-induced phase transformations and phase boundaries in high-Ni layered cathodes.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
High-Performance/-Precision/-Z(HPPZ) Scintillator Grids via Advanced Electrochemistry. Phase I – Project # 20210572MFR- Mid year review [Slides]
Scintillation grids with improved imaging resolution in time and space, are required for future mission needs at various facilities (pRad user station, LANSCE, DARHT, Scorpius etc). Current technologies use inorganic crystal scintillators, which are positioned within a high-Z scintillator septa. Dense and high-Z materials are optimal for gamma-ray detection making them promising candidates for development of high -performance/-precision/-Z (HPPZ) scintillator grids. The current resolution of standard chemical etching and fabrication processes of high-Z materials is very low, leading to undesired undercutting and ultimately reducing crystal performance efficiency. Goals are to: Perform initial feasibility studies with the aim of producing complex parts for applications with difficult-to-process high-Z material; Use of pulse and pulse-reverse electrochemical methods on additive approaches to produce high-precision Au and Re scintillator grids at a small scale; and, Follow up in Phase II with the delivery of a large-scale scintillator grid of the best material candidate with unprecedented properties for LANL needs determined in Phase I.
36 MATERIALS SCIENCE↗