SEARCH · Search NASA

Results for “Mechanical testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Report on Inventory of Samples from Six Capsules from BOR-60

As part of the University of Michigan Grand Challenge Integrated Research Project, Oak Ridge National Laboratory (ORNL) received a drum containing six capsules from Pacific Northwest National Laboratory in August 2025. Each capsule originated at the University of Michigan and contained approximately 44 disks of various iron-based alloys (T91, HT9, T92, 800H, and others). These capsules were irradiated at several temperatures in the BOR-60 fast reactor for multiple cycles to accumulate high levels of damage. The drum was sent to the Irradiated Materials Examination and Testing (IMET) hot cell facility, a Class III nuclear facility, located in Building 3025E at ORNL. The IMET hot cell facility at ORNL is designed to receive irradiation capsules from the High Flux Isotope Reactor and perform capsule opening, basic optical examination, and mechanical testing on neutron-irradiated materials. Capsules were unloaded from the drum and placed in cell 6 for disassembly in February 2026. A low-speed saw opened each capsule, and a manipulator moved the disks to a dual microscope setup for disk identification, as shown in Figure 1.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Quasi-static to Dynamic Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) has a need to understand the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys made by conventional wrought processing and additive manufacturing (AM). This two-year work scope will be performed at the Colorado School of Mines (Mines) and will include quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with high strain rate (Kolsky) pressure bar testing in tension and compression (e.g., 10 3 s -1 ), without and with temperature variations. Gas gun experiments at higher strain rates (e.g., over 10 3 s -1 ) will also be pursued. Complementary microstructure characterization will be performed on undeformed and deformed samples to fundamentally understand the role of processing on the microstructure characteristics and resulting deformation mechanisms that dictate the mechanical response of these alloys with variations in strain rate, temperature, and strain state. Alloys of interest will be Ta-based, containing up to 10 wt.% W. LLNL will supply initial wrought-processed material for sample machining. LLNL will also supply samples built by AM during the project for testing. Arc melting and casting may also be performed at Mines to produce small quantities of different alloys for machining and exploratory testing on an as-needed basis. This project will support multiple postdocs and graduate students at Mines, training them with the knowledge, skills, and abilities needed to study materials under extreme conditions of interest to the National Nuclear Security Agency.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Influence of the as-built microstructure on the recrystallization of an additively manufactured Inconel939 Ni-based superalloy

This study investigates the influence of the as-built microstructure on the recrystallization (RX) behavior and mechanical properties of the Ni-based superalloy Inconel 939 produced by laser powder bed fusion (PBF-LB/M). Two distinct as-built microstructures were obtained by varying the hatch distance (h d ): a columnar, strongly textured condition (h d =50, termed h d 50) and an equiaxed, weakly textured condition (h d =70, termed h d 70)). Both were subjected to nine solution treatments combining three temperatures (1100, 1150, and 1200 °C) and three holding times (1, 4, and 8 h). Comprehensive microstructural characterization was conducted to assess grain morphology, texture, grain boundary character, dislocation density, and precipitate distribution. Recrystallization was found to be significantly slower than in cast counterparts, requiring higher temperatures and longer times for completion. The initial microstructure plays a decisive role: full RX was achieved only in hd70 specimens after treatment at 1200 °C for 8 h, whereas hd50 samples exhibited delayed and incomplete RX under identical conditions. This behavior is attributed to the finer grain size and higher fraction of high-angle grain boundaries in hd70, which promote recrystallization. Mechanical testing revealed that hd70 samples subjected to a 1200 °C/8 h treatment followed by standard double ageing show higher yield and tensile strengths across the investigated temperature range than both printed and cast Inconel939 processed under conventional conditions, albeit with slightly reduced ductility. The enhanced mechanical performance is attributed to the larger grain size, which limits grain boundary sliding. These results demonstrate the critical importance of controlling the as-built microstructure and tailoring post-processing strategies to optimize high-temperature performance of PBF-LB/M Inconel939.

Inconel939↗

DOE OSTI2022

Revealing nanomechanical deformation at the interface and degradation in all-thin-film inorganic electrochromic devices

Recently, progress in electrochromic (EC) devices has been made in optimizing electrode and device configurations and performance. However, the ion insertion/de-insertion induced charge transfer (CT) nanomechanical effect has remained unexplored, i.e., repetitive electrode size changes at the nanoscale and stress/strain generated during electrochemical cycling, which is the focus of this work due to its intimate correlation with the elastic and plastic deformation at the interface. Considering the intervalence electrons, excellent electrochemical kinetics, and dramatic color changes, tungsten oxide (WO 3 ) and nickel oxide (NiO) films are configured as the EC cathode and anode materials, respectively, within a full device. Upon extended cycles (>10 000), the void generation and delamination that occurred at the interface account for performance decay. Encouraged by the findings, nanoindentation mechanical tests and electrical kelvin probe force microscopy were employed to investigate the CT induced effects at the interface. There is a dramatic increase of up to 45% in the elastic Young's modulus in colored/charged WO 3 at ~40 mC cm -2 . Here, the correlation between CT and synergistic mechanical effect is interpreted by the Lippman equation. Interestingly, despite the charged state (colored; lithiated) with a relatively flat morphology bringing an ~3.4 times higher electrostatic surface potential, the electrical work function unexpectedly decreases, arising from the dominant effect of the dipole layer potential over the chemical potential. The interatomic cohesive energy and equilibrium distance increase bury the seeds for mechanical deformation in the long run. This work provides fundamental insights into electro-chemo mechanics and interdisciplinary concerted interfacial effects at the nano/atomic level. The dependence of surface potential, stress, work function, and cohesive energy on electrochemical kinetics has been interpreted.

36 MATERIALS SCIENCE↗

DOE OSTI2021

A Combinatorial Approach to Testing and Characterization of Irradiated Fuels and Materials

•Combinatorial approaches to testing and characterization of materials is a very powerful tool to help explore some fundamentals of materials science.? •Three topics will be explored to help illustrate this:? •A fitness-for-service assessment of a CANDU component (this is work from my past)? •The use of small-scale mechanical testing of Cr-coated ATF cladding in support of qualification (this is work developed upon joining INL)? •A multi-scale characterization approach of TRISO fuel to investigate fission gas migration and microstructural features (this is work I now get to participate in on joining MFC)? •?

36 - MATERIALS SCIENCE↗

DOE OSTI2020

Mechanoadaptive strain and functional osseointegration of dental implants in rats

Spatiotemporal implant-bone biomechanics and mechanoadaptive strains in peri-implant tissue are poorly understood. Physical and chemical characteristics of an implant-bone complex (IBC) were correlated in three-dimensional space (along the length and around a dental implant) to gather insights into time related integration of the implant with the cortical portion of a jaw bone in a rat. Rats (N = 9) were divided into three experimental groups with three rats per time point; 3-, 11-, and 24-day. All rats were fed crumbled hard pellets mixed with water (soft-food diet) for the first 3 days followed by a hard-food diet with intact hard-food pellets (groups of 11- and 24-day only). Biomechanics of the IBCs harvested from rats at each time point was evaluated by performing mechanical testing in situ in tandem with X-ray imaging. The effect of physical association (contact area) of a loaded implant with adapting peri-implant tissue, and resulting strain within was mapped by using digital volume correlation (DVC) technique. The IBC stiffness at respective time points was correlated with mechanical strain in peri-implant tissue. Results illustrated that IBC stiffness at 11-day was lower than that observed at 3-day. However, at 24-day, IBC stiffness recovered to that which was observed at 3-day. Furthermore, correlative microscopy and spectroscopy illustrated that the lower IBC stiffness was constituted by softer and less mineralized peri-implant tissue that contained varying expressions of osteoconductive elements. Lower IBC stiffness observed at 11-day was constituted by less mineralized peri-implant tissue with osteoconductive elements that included phosphorus (P) which was co-localized with higher expression of zinc (Zn), and lower expression of calcium (Ca). Higher IBC stiffness at 24-day was constituted by mineralized peri-implant tissue with higher expressions of osteoconductive elements including Ca and P, and lower expressions of Zn. These spatiotemporal correlative maps of peri-implant tissue architecture, heterogeneous distribution of mineral density, and elemental colocalization underscore mechanoadaptive physicochemical properties of peri-implant tissue that facilitate functional osseointegration of an implant. These results provided insights into 1) plausible "prescription" of mechanical loads as an osteoinductive "therapeutic dose" to encourage osteoconductive elements in the peri-implant tissue that would facilitate functional osseointegration of the implant; 2) a "critical temporal window" between 3 and 11 days, and perhaps it is this acute phase during which key candidate regenerative molecules can be harnessed to accelerate osseointegration of an implant under load.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2025

Status Update for the Bearing Test Article Design Development – FY2025

Argonne National Laboratory’s (ANL) Mechanism Engineering Test Loop (METL) team has completed the design of a new Bearing Test Article (BTA) to test mechanical bearings for sodium fast reactor (SFR) mechanism applications. Recognition of the need for further bearing testing arose due to failure of rolling element bearings during testing of components for in-vessel fuel handling machines (FHMs) conducted at ANL in the METL facility. While the initial concept of the BTA arose from a need for bearing testing for FHM applications, the BTA design is configurable to test bearings of various sizes, types, and materials submerged in liquid sodium. Requirements for loading, shaft speed, temperature, and bearing size range were chosen based on requirements for SFR fuel handling. Modular components in the test bearing housings and shaft sleeves allow the design to accommodate a wide range of bearing sizes without modification to the larger assembly. Loading will be applied with screw jacks on the air side of the test article that will be adjusted to apply radial, thrust, or combined loading conditions. Applied force will be measured by load cells in-line with the loading mechanisms. In FY25 we have completed the design of the test article that will be fabricated and undergo testing at the METL facility. Drawing packages for the fabrication of the test article have been drafted and are being reviewed to add part tolerances and we have started ordering off-the-shelf components. The report will summarize the development of the Bearing Test Article design starting with an overview of the entire test article, then a more detailed examination of the bearing test section, loading mechanisms, test article ports and seals, and support structures, including analysis that went into significant design choices.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Post-irradiation examination of UN-Mo-W fuels for space nuclear propulsion

The National Aeronautics and Space Administration's return to space nuclear propulsion stems from the need for a more efficient method of space travel. Nuclear thermal propulsion systems have been shown to be two times more efficient than chemical propulsion. NASA's Sirius program was created to fabricate and test fuels for space nuclear propulsion, specifically to determine their performance under prototypical startup conditions. The Sirius project featured 4 test capsules, Sirius-1 featured uranium nitride fuel dispersed in a matrix of tungsten and rhenium, while Sirius-2A, -2B, and -3 featured uranium nitride-molybdenum-tungsten fuel (UN-Mo-W). This study discusses the Sirius-2A and -2B irradiation experiments at the Idaho National Laboratory, specifically their performance under irradiation at the Transient Reactor Test Facility. It was found that the fuel samples overall did not exhibit significant cracking, though the Sirius-2A fuel did have one large crack on the surface of the fuel. There was minimal hydrogen absorption in the samples, though it is unknown if the absorption occurred during irradiation or during fabrication. Mechanical testing indicated that the UN fuel demonstrated ceramic behavior as expected, and the Mo/W matrix demonstrated linear elastic behavior to failure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Helium effects and bubbles formation in irradiated Ti 3 SiC 2

Ti 3 SiC 2 is a potential structural material for nuclear reactor applications. However, He irradiation effects in this material are not well understood, especially at high temperatures. Here, we compare the effects of He irradiation in Ti 3 SiC 2 at room temperature (RT) and at 750 °C. Irradiation at 750 °C was found to lead to extremely elongated He bubbles that are concentrated in the nano-laminate layers of Ti 3 SiC 2 , whereas the overall crystal structure of the material remained intact. In contrast, at RT, the layered structure was significantly damaged and highly disordered after irradiation. Our study reveals that at elevated temperatures, the unique structure of Ti 3 SiC 2 can accommodate large amounts of He atoms in the nano-laminate layer, without compromising the structural stability of the material. The structure and the mechanical tests results show that the irradiation induced swelling and hardening at 750 °C are much smaller than those at RT. Overall, these results indicate that Ti 3 SiC 2 has an excellent resistance to accumulation of radiation-induced He impurities and that it has a considerable tolerance to irradiation-induced degradation of mechanical properties at high temperatures.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Storing Co 2 in Built Infrastructure: Co 2 Carbonation of Precast Concrete Products

The overall objective of the proposed study was to advance the technical understanding of CO 2 incorporation into novel cementitious materials for the development of high value products that provide a net reduction in carbon emissions. This project combined two primary phases of research that addressed technical barriers related to (i) optimizing CO 2 storage capability of cementitious materials, (ii) evaluating and enhancing physical properties of novel carbonated materials, and (iii) assessing the reductions in life cycle CO 2 emissions attributed to CO 2 carbonation of precast cementitious materials. Engineered cementitious composites (ECC) are a class of highly ductile concrete composites that have been shown to be very durable when used in the built environment. CO 2 carbonation of ECC was examined in this study and it was found that precast ECC specimens could sequester up to 35% CO 2 by cement mass after 24 hours of curing at a CO 2 pressure of 0.5 MPa and 23°C and had a strain capacity of 3%. Carbonation conditions were optimized at the bench-scale and then utilized to create full-scale CO 2 -cured ECC railroad ties that were field tested on a train track. Rail ties were selected for this initial assessment of CO 2 storage in precast concrete materials due to the large market for concrete ties in the railroad industry. Although the full-scale rail ties passed all of the required American Railway Engineering and Maintenance-of-Way Association qualifying mechanical tests, on-track testing of the CO 2 -cured ECC rail ties was unsuccessful due to fiber alignment in the ECC the during the rail tie casting process which prevented the material from achieving the expected level of strain capacity. This result highlights the challenge in scaling up bench-scale processes to full-scale product manufacturing and requires additional investigation into the casting process of large-scale infrastructure elements using ECC combined with carbonation curing. Life cycle assessment of a CO 2 -cured ECC rail tie versus a traditional concrete rail tie indicates that the ECC tie can have lifecycle carbon savings of between 11% and 51% depending on how much longer its useful lifetime is compared to traditional concrete rail ties. Both carbon and cost savings are driven by a reduction in the need to replace broken rail ties, so the key factor is the extent to which a CO 2 -cured ECC rail tie will have increased lifetime durability compared to alternative rail ties.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Comparative Analysis of Radial and Random Microstructures of Mesophase Pitch Carbon Fibers

Carbon fibers (CF) with radial and random microstructures are produced. Here, these fibers are subjected to identical treatment before being mechanically tested and analyzed with Weibull analysis, with the results revealing a statistically significant difference in tensile strengths of 2.23 GPa for random CF and 1.69 GPa for radial CF. Raman mapping probed the crystalline structure perpendicular to the fiber axis and found a uniform structure, while wide‐angle X‐ray diffraction showed a significant difference of 7.5 Å in the crystallites’ basal lengths parallel to the fiber. Small‐angle X‐ray scattering is completed parallel to the fiber for the first time. A cross‐section Guinier plot of the 1D azimuthal integration is generated assuming symmetric scattering, and the parallel scatterers are found to have a similar length scale to the crystallite's length, validating the testing method. Finally, transmission electron microscopy is completed on the longitudinal cross‐section of each fiber. The radial carbon fiber is found to have a core–shell structure, as evidenced further by fast Fourier transform images. Through all studies, it is shown that the structure developed during mesophase pitch spinning altered the microstructure, thus impacting the mechanical properties, confirming a direct relationship between processing, structure, and properties.

Scherschel, Alexander [Univ. of Virginia, Charlott↗

DOE OSTI2024

7 Innovations in high-rate composite manufacturing: integrating additive manufacturing with compression molding process

Advanced composites play a pivotal role in modern engineering, offering exceptional strength-to-weight ratios and tailored properties, essential for various industries. High-rate composite manufacturing techniques have rapid production capabilities, which are essential for meeting the demands of industries requiring cost-saving, efficiency, and quick turnaround times. This chapter explores the Additive Manufacturing- Compression Molding (AM-CM) system developed by Oak Ridge National Laboratory (ORNL) for advanced composites manufacturing. The AM-CM system integrates additive manufacturing with compression molding, facilitating the production of polymer composite parts with superior mechanical properties and meticulously controlled microstructures. This innovative system not only ensures precise material deposition but also operates as a fast composite manufacturing process, enhancing productivity and performance, which are needed attributes across industrial applications. Through comprehensive mechanical testing and microstructural analysis, AM-CM promotes remarkable fiber alignment and reduced porosity in composite parts compared to alternative thermoplastic high-rate composite manufacturing methods. Furthermore, AM-CM enables overmolding reinforcement using continuous carbon fiber and supports selective reinforcement through customizable toolpaths. It also facilitates the production of hybrid materials to achieve tailored mechanical properties. Future advancements in AM-CM technology aim to enhance process efficiency, broaden material versatility, and improve part performance. This involves exploring novel materials, advancing process monitoring, implementing automation technologies, and integrating artificial intelligence (AI) and machine learning (ML) for predictive modeling and real-time optimization in composite manufacturing. These developments will establish the AM-CM system as a transformative technology in composite manufacturing, driving innovation across industries.

Hassen, Ahmed [ORNL] (ORCID:0000000328521222)↗

DOE OSTI2024

Distinct Mechanism of Anti-Corrosion and Swelling-Adhesion Modeling of Low-Dimensional Nylon-Fluoropolymer Composite Coatings

Compared to other polymers, composite coatings with fluoropolymers as the matrix have attracted considerable interest due to their mechanical performance, chemical stability, and low surface energy. Herein, we present an anticorrosion mechanism of fluoropolymer composite coatings achieved by dispersing varying amounts of polyamide 12 (PA-12) particles over a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix. The choice of PVDF-HFP as a coating matrix was driven by its superior processability and mechanical properties over Teflon, while PA-12 afforded swelling capacity, preventing electrolyte permeation, and inhibiting matrix stress crack propagation. The corrosion resistance of the coatings was assessed mainly by potentiodynamic polarization and impedance measurements while being immersed in a NaCl solution. Our electrochemical measurement findings showed that 0.75% w/w PA-12 in the PVDF-HFP matrix significantly enhanced corrosion protection even after 21 days of immersion. Microscopy, dielectric spectroscopy, surface analysis, and mechanical testing (American Society for Testing and Materials standards) corroborated the results. PVDF-HFP coatings containing a minimum percolation threshold of 0.75 wt % PA-12 with 1 mil thickness on mild steel exhibited a remarkable increase in resistance and film adhesion, and a notable corrosion rate decrease. Finite element analysis simulation with a bilinear traction-separation law confirmed the swelling mechanism and adhesion behavior. Finally, this study highlights the potential of nylon particle dispersion in PVDF-HFP matrices as a practical approach to developing advanced anticorrosion coatings with promising practical applications in various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Performance of Lithium-Ion Batteries with 3D Printed Anodes and Compressible Carbon Structures

Carbon scaffolds have been shown to improve the performance of Li metal anodes in Li-ion batteries by acting as conductive hosts for Li metal plating and stripping. The scaffolds provide a more uniform electric field, and their 3D geometry enables smaller diffusion paths for the Li ions. In this project, several different types of carbon lattices were 3D printed, mechanically tested, and analyzed in coin cells. Planar and 3D printed graphite coatings were evaluated as the baseline, since graphite is a common anode material. The results showed that implementing a 3D graphite lattice into a coin cell improved the Li plating and stripping efficiency compared to the planar coating. However, since graphite can intercalate Li ions, other carbon materials were also explored that should act as better hosts for Li plating/stripping. To improve the compressibility of these non-graphite carbon scaffolds, five different carbon ink formulations were 3D printed in lattice configurations. SEM imaging and compression testing showed that both the final dimensions and the compressibility of the carbon lattices depended on the type of carbon precursors used. The two most suitable compositions were found to be those made with graphene oxide-resorcinol formaldehyde and graphene oxide-ammonium hydroxide. In the future, these formulations will be further refined to increase their mechanical strength, and their performance as scaffold hosts for Li metal anodes will be evaluated in coin cells.

25 ENERGY STORAGE↗

DOE OSTI2026

TEM Approaches for Microstructure-Informed Prediction of Mechanical Properties in Structural Alloys

Predicting the mechanical performance of structural alloys from their evolving microstructure remains a major challenge in materials science, particularly for nuclear structural materials, where irradiation-induced defects span multiple types and length scales and interact through complex mechanisms. The dispersed barrier hardening (DBH) [1] and Friedel–Kroupa–Hirsch (FKH) [2,3] models have been widely used to evaluate the hardening contributions of individual obstacles and to estimate tensile strength from quantified microstructures; however, when multiple size-dependent obstacles coexist and evolve, predicting temperature-dependent tensile strength becomes significantly more complex, and a fully consistent hardening model is still lacking. Transmission electron microscopy (TEM) plays a central role in refining hardening models and enabling predictive assessments of tensile strength evolution by providing quantitative characterization of dislocations, irradiation-induced defects (e.g., dislocation loops and cavities), precipitates, and grain structure (Fig. 1.). These experimentally measured defect densities are incorporated into physically based hardening models with size- and shape- dependent obstacle strengths [4], using root-sum-square superposition for obstacles of comparable strength and linear superposition for dissimilar ones [5]. In addition, recent advances in TEM [6-8], including high-resolution imaging, 4D-STEM strain mapping, EDS/EELS elemental analysis, and flash-polishing-based TEM specimen preparation and extraction-replica methods (Fig. 2), further improve the accuracy of microstructural quantification. By comparison with prior studies as well as our own results, we show that when TEM-derived microstructural information is carefully integrated with physically grounded hardening models, yield strength (or irradiation-induced hardening) measured at room temperature can be predicted with good quantitative agreement across multiple alloy classes. In-situ TEM combined with high-temperature mechanical testing represents an important next step for refining hardening models by directly probing dislocation–obstacle interactions across varying irradiation doses and temperatures [9]. Because the barrier strength factor (α) depends on both temperature and obstacle size, it should not be treated as a constant fitting parameter; rather, it must be explicitly evaluated to achieve physically meaningful predictions of mechanical behaviour at operating temperatures. This presentation therefore discusses why all strengthening contributions (e.g., Peierls stress, solid-solution strengthening, voids, bubbles, dislocation loops, dislocation lines, and grain boundaries) must be considered collectively, why appropriate superposition methods are essential when obstacles possess different barrier strength factors, how hardness measurements can be meaningfully related to tensile properties, and how TEM-derived microstructural information can be systematically incorporated into hardening models. More broadly, it outlines a pathway toward microstructure-informed prediction of mechanical properties and supports the goal of establishing science-based tools for evaluating structural materials in extreme environments [10].

Lin, Yan-Ru [ORNL] (ORCID:0000000339991473)↗

DOE OSTI2024

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗

DOE OSTI2022

High Strength Steel-Aluminum Components by Vaporizing Foil Actuator Welding

This project aimed to address the challenge of effectively welding dissimilar materials—high-strength steel and high-strength aluminum for creating lightweight, multi-material automotive components. For automotive companies, reducing weight of a vehicle is critical task regulated by the government to solve the issue of greenhouse gas emissions. Production of lightweight cars and trucks can be achieved by substitution of current all-steel structures with multi-material lightweight structures that include high strength-to-weight-ration materials such as high-strength steels, aluminum alloys, magnesium alloys, titanium alloys, coupled with lightweight designs. This requires dissimilar metal welding, which is challenging for state of the art joining processes such as resistance spot welding. The cycle of melting-cooling-freezing during traditional welding that can easily ruin the designed outstanding properties of the advanced base metals, such as aluminum alloys, making the welded area much weaker than the base metals. To weld two different metals with great difference in melting points, such as aluminum and steel, it’s even more difficult or impossible because of the formation of brittle intermetallic compounds at the welded interface. In this project, a novel welding method, developed at OSU, was selected for validation and development. This novel technology enables welding by impact without melting and proves to be robust to join various dissimilar lightweight metals. Termed as vaporizing foil actuator welding or VFAW, the technology uses a thin aluminum foil that is rapidly vaporized by a high current pulse to produce an explosive-like pressure pulse to drive one metallic piece into another at the high speed required for impact welding. This project entailed development of the early-stage welding technology in terms of (a) the consumables, the welding apparatus and the power sources, (b) coupon scale screening of many material combinations including corrosion studies, (c) computational modeling and design of the welded interface as well as of the multi-material prototype component, and (d) mechanical testing for strength and durability at coupon scale and to a certain extent the prototype scale. The all-steel engine cradle of 2016 Chevrolet Cruze was chosen as the baseline prototype component. The target set for the project was to demonstrate a 20% weight reduction at a cost premium of less than $\$ $5/lb saved without compromising on baseline mechanical properties. At project completion, a 12% lighter prototype component was demonstrated with an estimated cost premium of $\$ $9.8/lb saved. Besides prototype level demonstration of the technology, this project also enabled elevation of the technology’s readiness level to where a hydraulically actuated welding head was developed and made ready for deployment at a research and development facility for Tier 1 automotive supplier.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Innovative Nuclear Materials Outboard-A Project Specimen Preparation Guide

The Innovative Nuclear Materials (INM) Program was recently established by the U.S. Department of Energy (DOE) to develop advanced material technologies for use in nuclear reactors. The INM program is presently focused on researching in-core non-fueled materials for application in fast spectrum nuclear reactors. The widespread deployment of fast reactors continues to be a prominent aspiration for advanced nuclear technology developers. However, companies working to license these reactors have no choice but to rely on historic material technologies since further optimization and advancement of these materials is impeded by the lack of fast neutron irradiation test facilities. INM-OA is a non-fueled drop-in experiment which will irradiate material specimens of interest to fast reactor applications. This experiment will be irradiated at Idaho National Laboratory (INL) in the Advanced Test Reactor (ATR) outboard-A (OA) position during normal and high temperature steady state (HTSS) cycles. It will include material specimens supplied by members of the INM program and will utilize a cadmium-lined basket to filter out incident thermal neutrons, thus simulating a faster neutron energy spectrum. Material specimens will undergo post-irradiation examination including microscopy and mechanical testing. In addition to absorption reactions, fast neutrons cause microstructural damage in materials by atom displacement, which can cause exacerbated changes in physical properties and behavior. Thus, the data obtained from the INM-OA experiment will be crucial for understanding the engineering-scale behavior of reactor materials. This document is intended for the Principal Investigators providing samples for this project. Topics included are a general description of the experiment, the irradiation experiment/capsule design, sample geometries, number of samples to be provided, documentation to be provided, a brief list potentially useful characterization methods that can be leveraged at INL, and other miscellaneous requirements specific to this project. This document is intended for informational use only.

innovative nuclear materials↗