Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxygen release”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Mass analysis of neutral particles and ions released during electrical breakdowns on spacecraft surfaces

Charged-particle fluxes from breakdown events were studied. Methods to measure mass spectra and total emitted flux of neutral particles were developed. The design and construction of the specialized mass spectrometer was completed. Electrical breakdowns were initiated by a movable blunt contact touching the insulating surface. The contact discharge apparatus was used for final development of two different high-speed recording systems and for measurements of the composition of the materials given off by the discharge. It was shown that intense instantaneous fluxes of neutral particles were released from the sites of electrical breakdown events. A laser micropulse mass analyzer showed that visible discoloration at breakdown sites were correllated with the presence of iron on the polymer side of the film, presumably caused by punch-through to the Inconel backing. Kapton samples irradiated by an oxygen ion beam were tested. The irradiated samples were free of surface hydrocarbon contamination but otherwise behaved in the same way as the Kapton samples tested earlier. Only the two samples exposed to oxygen ion bombardment were relatively clean. This indicates an additional variable that should be considered when testing spacecraft materials in the laboratory.

Kendall, B. R. F.↗
NASA NTRS1985

Oxygen extraction from lunar materials - An experimental test of an ilmenite reduction process

The reaction of ilmenite with hydrogen to produce water has been studied experimentally in order to evaluate the effectiveness of using a cold trap to improve yields in a continuous flow process. Yields were enhanced, but not to the degree observed in batch processing systems. The terrestrial simulant used in these studies contained traces of iron sulfide, which released H2S during processing with a deleterious effect on several components of the test system. More sophisticated testing should be undertaken to obtain kinetic data and attention given to the removal of sulfides in the pre-process beneficiation.

Williams, R. J.↗
NASA NTRS1978

Chemical interpretation of Viking Lander 1 life detection experiment

An earth-based evaluation of the Viking Lander 1 life-detection experiments was conducted using a radiofrequency glow discharge in a simulated Martian atmosphere. The Gas Exchange Experiment conducted in the humid mode released substantial amounts of CO2, O2, N2, Ar, and CO into the atmosphere, indicating that these substances were adsorbed onto the Martian soil. An adsorption potential plot is given, graphing quantity of gas against time (d). For a model surface area of 17 squares meters per gram of measured substance, oxygen adsorption was found to be relatively high, a result which tends to confirm the hypothesis that Martian oxygen exists largely in chemisorbed states or in active oxygen compounds, e.g., peroxide, superoxide, hydroperoxide

Ballou, E. V.↗
NASA NTRS1992

Ignition delays, heats of combustion, and reaction rates of aluminum alkyl derivatives used as ignition and combustion enhancers for supersonic combustors

The work was based on adapting an apparatus and procedure developed at Southwest Research Institute for rating the ignition quality of fuels for diesel engines. Aluminum alkyls and various Lewis-base adducts of these materials, both neat and mixed 50/50 with pure JP-10 hydrocarbon, were injected into the combustion bomb using a high-pressure injection system. The bomb was pre-charged with air that was set at various initial temperatures and pressures for constant oxygen density. The ignition delay times were determined for the test materials at these different initial conditions. The data are presented in absolute terms as well as comparisons with the parent alkyls. The relative heats of reaction of the various test materials were estimated based on a computation of the heat release, using the pressure data recorded during combustion in the bomb. In addition, the global reaction rates for each material were compared at a selected tmperature and pressure.

Ryan, T. W., III↗
NASA NTRS1994

Intermittent gravity: How much, how often, how long?

Continuous exposure to gravity may not be necessary to prevent the deconditioning effects of microgravity. It is not known, however, what the minimum gravity (G) exposure reguirements are, whether they vary for different physiological systems, or whether passive Gz (gravity in the head-to-toe vector) or activity in a G field is more effective in preventing deconditioning. It is also not known what the optimal characteristics of the G stimulus should be in terms of amplitude, duration, and frequency. To begin to address these questions, a 4-day -6 deg head-down bed rest (HDBR) study was conducted. Nine males (aged 30-50 yr) were subjected, over a period of seven months, to four different +1 Gz exposure protocols (periodic standing or controlled walking each for a total of 2 or 4 hr/day in individual 15-min doses), plus a control (0 Gz) of continuous HDBR. The study consisted of one ambulatory control day, 4 full days of -6 deg HDBR, and a recovery day when subjects were released at the end of HDBR after completion of tests. A battery of tests was selected and standardized in order to evaluate the known early responses to HDBR. Dependent variables of interest included orthostatic tolerance (30 min at 60 deg head-up tilt) and hemodynamics during head-up tilt, peak oxygen consumption (VO2(sub peak)) plasma volume (PV), and urinary calcium (Ca). The results were as follows: 4 hr standing completely prevented and 2 hr walking partially prevented post-HDBR orthostatic intolerance. Walking at 3 mi/hr for 4 hr/day provided no additional benefit. Intermittent walking attenuated, but did not prevent, the decrease in VO2(sub peak). Both 4 hr conditions showed less PV loss by the end of HDBR; both 2 hr conditions were without effect. Both 2 and 4 hr walking essentially prevented urinary Ca excretion and were more effective than standing. It is concluded that different physiological systems benefit differentially from passive +1 Gz or activity in +1 Gz, and the intensity of the stimulus may be an important contributing factor.

Vernikos, Joan↗
NASA NTRS2000

Carbon and Oxygen Budgets of Subtidal and Intertidal Cyanobacterial Mats

Intertidal cyanobacterial mats (Lyngbya-dominated) are contrasted with mats (Microcoleus-dominated) that grow in subtidal (0.7m water depth) hypersaline (90-110 permil) environments. In benthic chamber experiments conducted in Oct., 1999, mats exhibited greater net uptake of dissolved inorganic carbon (DIC) from overlying water during the daylight period than Microcoleus mats (e.g., 200 vs 120 mmol C/m. at 26 deg C, respectively). Net DIC release at night was similar for both mats (approx. 80 mmol C/m). Daytime net O2 release by Lyngby mats exceeded that by Microcoleus mats (150 vs 100 mmol O2/m), and O2 uptake at night was comparable for both mats (60-80 mmol O2/m). Nonphotosynthetic populations are more prominent within the subtidal versus intertidal mats, and accordingly exhibited greater internal 02 uptake and DIC production during the day. Over 24 hours, Lyngby-dominated mats exhibited greater net uptake of DIC than subtidal Microcoleus mats, consistent with these intertidal mats being "pioneer" communities that constantly recover from periodic physical disruption in energetic environments. The Microcoleus-dominated mats achieve steady-state mat thicknesses by balancing primary production against diagenetic decomposition of cellular and extracellular organic constituents.

DesMarais, David J.↗
NASA NTRS1993

On the escape of oxygen and hydrogen from Mars

Escape rates of oxygen atoms from dissociative recombination of O2(+) above the Martian exobase are computed in light of new information from ab initio calculations of the dissociative recombination process and our recently revised understanding of the Martian dayside ionosphere. Only about 60 percent of the dissociative recombinations occur in channels in which the O atoms are released with energies in excess of the escape velocity. Futhermore, we find that the computed escape fluxes for O depend greatly on the nature of the ion loss process that has been found necessary to reproduce the topside ion density profiles measured by Viking. If it is assumed that the ions are not lost from the gravitational field of the planet, as required by an analysis of nitrogen escape, the computed average O escape rate is 3 x 10 exp 6/sq cm/s, much less than half the H escape rates inferred from measurements of the Lyman-alpha dayglow, which are in the range (1-2) x 10 exp 8/sq cm/s. Suggestions for restoring the relative escape rates of H and O to the stoichiometric ratio of water are explored.

Fox, J. L.↗
NASA NTRS2007

Lunar Resource Utilization: Development of a Reactor for Volatile Extraction from Regolith

The extraction and processing of planetary resources into useful products, known as In- Situ Resource Utilization (ISRU), will have a profound impact on the future of planetary exploration. One such effort is the RESOLVE (Regolith and Environment Science, Oxygen and Lunar Volatiles Extraction) Project, which aims to extract and quantify these resources. As part of the first Engineering Breadboard Unit, the Regolith Volatiles Characterization (RVC) reactor was designed and built at the NASA Glenn Research Center. By heating and agitating the lunar regolith, loosely bound volatiles, such as hydrogen and water, are released and stored in the reactor for later analysis and collection. Intended for operation on a robotic rover, the reactor features a lightweight, compact design, easy loading and unloading of the regolith, and uniform heating of the regolith by means of vibrofluidization. The reactor performance was demonstrated using regolith simulant, JSC1, with favorable results.

Kleinhenz, Julie E.↗
NASA NTRS1993

Silazine to silica

Thin film silica and/or methyl silicone were detected on most external surfaces of the retrieved LDEF. Both solar ultraviolet radiation and atomic oxygen can convert silicones to silica. Known sources of silicone in or on the LDEF appear inadequate to explain the ubiquitous presence of the silica and silicone films. Hexamethyldisilazane (HMDS) was used as the Challenger tile waterproofing compound for the Challenger/LDEF deployment mission. HMDS is both volatile and chemically reactive at STP. In addition, HMDS releases NH3 which depolymerizes silicone RTV's. Polyurethanes are also depolymerized. Experiments are reported that indicate much of the silicone and silica contamination of LDEF resulted directly or indirectly from HMDS.

Harvey, Gale A.↗
NASA NTRS1993

A model of concurrent flow flame spread over a thin solid fuel

A numerical model is developed to examine laminar flame spread and extinction over a thin solid fuel in lowspeed concurrent flows. The model provides a more precise fluid-mechanical description of the flame by incorporating an elliptic treatment of the upstream flame stabilization zone near the fuel burnout point. Parabolic equations are used to treat the downstream flame, which has a higher flow Reynolds number. The parabolic and elliptic regions are coupled smoothly by an appropriate matching of boundary conditions. The solid phase consists of an energy equation with surface radiative loss and a surface pyrolysis relation. Steady spread with constant flame and pyrolysis lengths is found possible for thin fuels and this facilitates the adoption of a moving coordinate system attached to the flame with the flame spread rate being an eigen value. Calculations are performed in purely forced flow in a range of velocities which are lower than those induced in a normal gravity buoyant environment. Both quenching and blowoff extinction are observed. The results show that as flow velocity or oxygen percentage is reduced, the flame spread rate, the pyrolysis length, and the flame length all decrease, as expected. The flame standoff distance from the solid and the reaction zone thickness, however, first increase with decreasing flow velocity, but eventually decrease very near the quenching extinction limit. The short, diffuse flames observed at low flow velocities and oxygen levels are consistent with available experimental data. The maximum flame temperature decreases slowly at first as flow velocity is reduced, then falls more steeply close to the quenching extinction limit. Low velocity quenching occurs as a result of heat loss. At low velocities, surface radiative loss becomes a significant fraction of the total combustion heat release. In addition, the shorter flame length causes an increase in the fraction of conduction downstream compared to conduction to the fuel. These heat losses lead to lower flame temperatures, and ultimately, extinction. This extinction mechanism differs from that of blowoff, where the flame is unable to be stabilized due to the high flow velocity.

Ferkul, Paul V.↗
NASA NTRS1992

Carbon isotope evidence for the stepwise oxidation of the Proterozoic environment

The oxidation of the earth's crust and the increase in atmospheric oxygen early in earth history have been linked to the accumulation of reduced carbon in sedimentary rocks. Trends in the carbon isotope composition of sedimentary organic carbon and carbonate show that during the Proterozoic aeon (2.5-0.54 Gyr ago) the organic carbon reservoir grew in size, relative to the carbonate reservoir. This increase, and the concomitant release of oxidizing power in the environment, occurred mostly during episodes of global rifting and orogeny.

Des Marais, David J.↗
NASA NTRS1992

Carbon Isotope Evidence for the Stepwise Oxidation of the Proterozoic Environment

The oxidation of the Earth's crust and the increase in atmospheric oxygen early in Earth history have been linked to the accumulation of reduced carbon in sedimentary rocks. Trends in the carbon isotope composition of sedimentary organic carbon and carbonate show that during the Proterozoic aeon (2.5-0.54 Gyr ago) the organic carbon reservoir grew in size, relative to the carbonate reservoir. This increase, and the concomitant release of oxidizing power in the environment, occurred mostly during episodes of global rifting and orogeny.

DesMarais, David J.↗
NASA NTRS1989

Plasma density fluctuations observed during Space Shuttle Orbiter water releases

Observations by the Langmuir probe on the Plasma Diagnostics Package flown as part of the Spacelab 2 mission in the summer of 1985 show a strong increase in the level of turbulence near the Shuttle Orbiter during operations in which liquid water is released. The spectrum of the plasma density fluctuations peaks at the lowest frequencies measured (a few Hz) and extends up to a few kHz, near the lower hybrid frequency. Two potential mechanisms for generating the plasma turbulence are suggested which are both based on the production of water ions as a result of charge exchange with the ambient oxygen ions in the ionosphere. The first mechanism proposed is the ion-plasma instability which arises from the drift of the contaminant with respect to the ambient oxygen ions. The other mechanism proposed is the Ott-Farley instability, which is a result of the ring distribution formed by the 'pick-up' water ions.

Pickett, J. S.↗
NASA NTRS1993

Observed Barium Emission Rates

The barium releases from the CRRES satellite have provided an opportunity for verifying theoretically calculated barium ion and neutral emission rates. Spectra of the five Caribbean releases in the summer of 1991 were taken with a spectrograph on board a U.S. Air Force jet aircraft. Because the line of sight release densities are not known, only relative rates could be obtained. The observed relative rates agree well with the theoretically calculated rates and, together with other observations, confirm the earlier detailed theoretical emission rates. The calculated emission rates can thus with good accuracy be used with photometric observations. It has been postulated that charge exchange between neutral barium and oxygen ions represents a significant source for ionization. If so. it should be associated with emissions at 4957.15 A and 5013.00 A, but these emissions were not detected.

Stenbaek-Nielsen, H. C.↗
NASA NTRS1994

Atomic Oxygen (ATOX) simulation of Teflon FEP and Kapton H surfaces using a high intensity, low energy, mass selected, ion beam facility

A high intensity (greater than 10(exp 15) ions/sq cm) low energy (down to 5 eV) mass selected ion beam (MSIB) facility was used to study the effects of ATOX on two polymers commonly used for space applications (Kapton H and Teflon FEP). The polymers were exposed to O(+) and Ne(+) fluences on 10(exp 15) - 10(exp 19) ions/sq cm, using 30eV ions. A variety of analytical methods were used to analyze the eroded surfaces including: (1) atomic force microscopy (AFM) for morphology measurements; (2) total mass loss measurements using a microbalance; (3) surface chemical composition using x-ray photoelectron spectroscopy (XPS), and (4) residual gas analysis (RGA) of the released gases during bombardment. The relative significance of the collisional and chemical degradation processes was evaluated by comparing the effects of Ne(+) and O(+) bombardment. For 30 eV ions it was found that the Kapton is eroded via chemical mechanisms while Teflon FEP is eroded via collisional mechanisms. AFM analysis was found very powerful in revealing the evolution of the damage from its initial atomic scale (roughness of approx. 1 nm) to its final microscopic scale (roughness greater than 1 micron). Both the surface morphology and the average roughness of the bombarded surfaces (averaged over 1 micron x 1 micron images by the system's computer) were determined for each sample. For 30 eV a non linear increase of the Kapton roughness with the O(+) fluence was discovered (a slow increase rate for fluences phi less than 5 x 10(exp 17) O(+)/sq cm, and a rapid increase rate for phi greater than 5 x 10(exp 17) O(+)/sq cm). Comparative studies on the same materials exposed to RF and DC oxygen plasmas indicate that the specific details of the erosion depend on the simulation facility emphasizing the advantages of the ion beam facility.

Vered, R.↗
NASA NTRS1998

Coordinated Studies of Magnetospheric/Ionospheric Coupling and Dynamics in the Diffuse Aurora

The results of the studies carried out under the grant are described in detail in the following publications: Atmospheric Response in Aurora experiment: Observations of E and F region neutral winds in a region of postmidnight diffuse aurora; Walterscheid, Modified geostrophy in the thermosphere, ARIA II neutral flywheel-driven field-aligned currents in the postmidnight sector of the auroral oval: A case study; Observations of unstable atmospheric shear layers in the lower E region in the post-midnight auroral oval; and Depletion of oxygen in aurora: Evidence for a local mechanism. The objective of the Atmospheric Response in Aurora (ARIA) experiment was to measure the response of the E-region neutral flow to substorm activity in the post-midnight sector of the auroral oval. To this end, neutral wind profiles were obtained from a series of four sets of rocket flights using the chemical release technique. The measurements covered conditions ranging from quiet to disturbed. A consistent feature of the observed winds in disturbed conditions is the presence of an E-region jet located between approximately 110 and 120 km altitude. The profiles presented here show that the neutral wind speeds near 110-120 km altitude increase and the hodographs become more elongated or linear in response to higher magnetic activity levels. The wind speeds decrease and the hodographs become more circular as the activity level decreases. The presence of a wind maximum implies shears both above and below. The observations consistently show larger shears below the peak and smaller shears above. In fact, the bottom-side shears during disturbed conditions have Richardson numbers close to or below the critical value of 0.25 suggesting that the flow is highly unstable in that height range. The instability is expected to produce waves, turbulence, and enhanced diffusivity.

Larsen, M. F.↗
NASA NTRS2009

Integrated Bio-ISRU and Life Support Systems at the Lunar Outpost: Concept and Preliminary Results

We continue the development of our concept of a biotechnological loop for in-situ resource extraction along with propellant and food production at a future lunar outpost, based on the cultivation of litholytic cyanobacteria (LCB) with lunar regolith (LR) in a geobioreactor energized by sunlight. Our preliminary studies have shown that phototropic cultivation of LCB with simulants of LR in a low-mineralized medium supplemented with CO2 leads to rock dissolution (bioweathering) with the resulting accumulation of Fe, Mg and Al in cyanobacterial cells and in the medium. LCB cultivated with LR simulants produces more O2 than the same organisms cultivated in a high-mineralized medium. The loss of rock mass after bioweathering with LCB suggests the release of O from regolith. Further studies of chemical pathways of released O are required. The bioweathering process is limited by the availability of CO2, N, and P. Since lunar regolith is mainly composed of O, Si, Ca, Al and Mg, we propose to use organic waste to supply a geobioreactor with C, N and P. The recycling of organic waste, including urine, through a geobioreactor will allow for efficient element extraction as well as oxygen and biomass production. The most critical conclusion is that a biological life support system tied to a geobioreactor might be more efficient for supporting an extraterrestrial outpost than a closed environmental system.

Brown, I. I.↗
NASA NTRS1985

The use of superoxide mixtures as air-revitalization chemicals in hyperbaric, self-contained, closed-circuit breathing apparatus

In portable breathing apparatus applications at 1 atm, potassium superoxide (KO2) has exhibited low-utilization efficiency of the available oxygen (O2) and diminished carbon dioxide-(CO2) scrubbing capacity caused by the formation of a fused, hydrated-hydroxide/carbonate product coating on the superoxide granules. In earlier work, it was discovered that granules fabricated from an intimate mixture of KO2 and calcium superoxide, Ca(O2)2, did not exhibit formation of a fused product coating and the utilization efficiency with respect to both O2 release and CO2 absorption was superior to KO2 granules when both types of granules were reacted with humidified CO2 under identified conditions. In the work described here, single pellets of KO2, KO2/Ca(O2), mixtures and commercially available KO2 tables and granules were reacted with a flow of humidified CO2 in helium at 1- and 10-atm total pressure and at an initial temperature of 40 C. In the 1-atm flow tests, the reaction rates and utilization efficiency of the KO2/Ca(O2)2 pellets were markedly superior to the KO2 pellets, tablets, and granules when the samples were reacted under identical conditions. However, at 10 atm, the rates of O2 release and CO2 absorption, as well as the utilization efficiencies of all the superoxide samples, were one-third to one-eighth of the values observed at 1 atm. The decrease in reaction performance at 10 atm compared to that at 1 atm has been attributed principally to the lower bulk diffusivity of the CO2 and H2O reactants in helium at the higher pressure and secondarily to the moderation of the reaction temperature caused by the higher heat capacity of the 10-atm helium.

Wood, P. C.↗