Search NASA⌕ Search

SEARCH · Search NASA

Results for “PENETRATION DEPTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Validation Exercise of a Coarse Finite Element Model of Laser Welds

The objective of this project is to validate low-fidelity models of 304L to 304L stainless steel partial-penetration laser welds for thin sheets. Low-fidelity means that the weld is represented by coarsely meshed element blocks. Here, the hexahedral element size is approx imately half the weld penetration depth. The material behavior of the block is represented by a J2 plasticity model with a Voce hardening function. The source of the data used in this work is an extensive experimental study conducted by Sharlotte Kramer (1528) and published in 2015. Figure 1 shows a cross-section of the weld of interest. The nominal thickness of the sheets is 0.063 in. while the target penetration depth of the weld is in the range of 0.028 to 0.032 in., extending about half the sheet thickness. Uniaxial tension tests provided data for calibration of base material and weld models. Results of two validation geometries were also provided. The principal validation geometry is shown in Fig. 2. It consists of a plate specimen with in-plane dimensions 6 in × 2.875 in loaded in tension. A circular plug with a 1.5 in. diameter was cut from the center of the plate and then welded in place. The details of the welding schedule are given. An important assumption is that the welds in the calibration and validation specimens have similar geometric and material properties as those in the validation tests. The task was to first calibrate models for the base material and the welds and then simulate the validation tests until the point of weld first failure.

36 MATERIALS SCIENCE↗

Superconducting properties and gap structure of the topological superconductor candidate Ti 3 Sb

Here, we present a study of the superconducting properties of the candidate topological superconductor Ti 3 Sb. Electrical transport measurements show zero resistance with a T c,onset of ≈ 5.9 K with a transition width ΔT c ≈ 0.6 K. The superconducting phase boundaries as derived from magnetotransport and magnetic susceptibility measurements agree well. We estimate an upper critical field B c2 (0) ≈ 4.5 T. A Ginzburg-Landau (GL) analysis yields values of the coherence length and penetration depth of ξ = 6.2 nm and λ = 340 nm, respectively, and a GL parameter κ ≈ 55, indicating extreme type-II behavior. Furthermore, we observe a step height in the specific heat $\frac{Δ C_e}{γ T_c}$ ≈ 1.61 ± 0.24 (with T c = 4.8 ± 0.4 K), a value larger than the Bardeen-Cooper-Schrieffer value of 1.43, suggesting modest coupling. Measurements of the temperature dependence of the London penetration depth via the tunnel-diode oscillator technique down to ≈ 450 mK show a full superconducting gap, consistent with a conventional s-wave gap structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Critical fields and vortex pinning in overdoped Ba 0.2 K 0.8 Fe 2 As 2

We determine the upper and lower critical fields, the penetration depth and the vortex pinning characteristics of single crystals of overdoped Ba 0.2 K 0.8 Fe 2 As 2 with T c ~ 10 K. We find that bulk vortex pinning is weak and vortex dynamics to be dominated by the geometrical surface barrier. The temperature dependence of the lower critical field, H c1 , displays a distinctive upturn at low temperatures, which is suggestive of two distinct superconducting gaps. Furthermore, the penetration depth, λ, varies linearly with temperature below 4 K indicative of line nodes in the superconducting gap. As a result, these observations can be well described in a model based on a multi-band nodal superconducting gap.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Disorder-Driven Transition from s ± to s + + Superconducting Order Parameter in Proton Irradiated Ba ( Fe 1 - x Rh x ) 2 As 2 Single Crystals

Here, microwave measurements of the London penetration depth and critical temperature T c were used to show evidence of a disordered-driven transition from s ± to s ++ order parameter symmetry in optimally doped Ba(Fe 1–x Rh x ) 2 As 2 single crystals, where disorder was induced by means of 3.5 MeV proton irradiation. Signatures of such a transition, as theoretically predicted, are found as a drop in the low-temperature values of the London penetration depth and a virtually disorder-independent superconducting T c . We show how these experimental observations can be described by multiband Eliashberg calculations in which the effect of disorder is accounted for in a suitable way. To this aim, an effective two-band approach is adopted, allowing us to treat disorder in a range between the Born approximation and the unitary limit.

36 MATERIALS SCIENCE↗

Unexpected Nonlinear Effects in Superconducting Transition-Edge Sensors

When a normal metal transitions into the superconducting state the DC resistance drops from a finite value to zero over some finite transition width in temperature, current, and magnetic field. Superconducting transition-edge sensors (TESs) operate within this transition region and uses resistive changes to measure deposited thermal energy. This resistive transition is not perfectly smooth and a wide range of TES designs and materials show sub-structure in the resistive transition (as seen in smooth nonmonotonic behavior, jump discontinuities, and hysteresis in the devices current-voltage relation and derivatives of the resistance with respect to temperature, bias current, and magnetic field). TES technology has advanced to the point where for many applications this structure is the limiting factor in performance and optimization consists of finding operating points away from these structures. For example, operating at or near this structure can lead to nonlinearity in the detectors response and gain scale, limit the spectral range of the detector by limiting the usable resistive range, and degrade energy resolution. The origin of much of this substructure is unknown. This presentation investigates a number of possible sources in turn. First we model the TES as a superconducting weak-link and solve for the characteristic differential equations current and voltage time dependence. We find:(1) measured DC biased current-voltage relationship is the time-average of a much higher frequency limit cycle solution.(2) We calculate the fundamental frequency and estimate the power radiated from the TES treating the bias leads as an antennae.(3) The solution for a set of circuit parameters becomes multivalued leading to current transitions between levels.(4)The circuit parameters can change the measure resistance and mask the true critical current. As a consequence the TES resistance surface is not just a function of temperature, current, and magnetic field but is also a function of the circuit elements (such as shunt resistor, SQUID inductance, and capacitor values). In other words, same device measured in different electrical circuits will have a different resistive surface in temperature, current, and magnetic field. Next we consider that at the transition temperature of a superconductor both the magnetic penetration depth and coherence length are divergent. As a consequence these important characteristic length scales are changing with operating point. We present measurements on devices showing commensurate behavior between these characteristic lengths and the length scale of added normal metal structures. Reordering of proximity vortices leads to discontinuities and irreversibility of the current-voltage curves. Last we consider a weak-link TES including both thermal activated resistance effects and the effect of the magnetic penetration depth being a function of temperature and magnetic field. We derive its impact on the resistive transition surface and the important device parameters a and b.

Superconducting Detectors↗

Spin waves and high-frequency response in layered superconductors with helical magnetic structure

Here, we evaluate the spin-wave spectrum and dynamic susceptibility in a layered superconductor with helical interlayer magnetic structure. We especially focus on the structure in which the moments rotate 90 degrees from layer to layer realized in the iron pnictide RbEuFe 4 As 4 . While in nonmagnetic superconductors low-frequency magnetic field decays on the distance of the order of the London penetration depth, spin waves mediate its propagation to much larger distances limited by external dissipation mechanisms. The spin-wave spectrum in superconductors is strongly renormalized due to the long-range electromagnetic interactions between the oscillating magnetic moments. This leads to strong enhancement of the frequency of the mode coupled with uniform field and this enhancement exists only within a narrow range of the c-axis wave vectors of the order of the inverse London penetration depth. The key feature of materials like RbEuFe 4 As 4 is that this uniform mode corresponds to the maximum frequency of the spin-wave spectrum with respect to the c-axis wave vector. As a consequence, the high-frequency surface resistance acquires a very distinct asymmetric feature spreading between the bare and renormalized frequencies. Finally, we also consider excitation of spin waves with the Josephson effect in a tunneling contact between helical-magnetic and conventional superconductors and study the interplay between the spin-wave features and geometrical cavity resonances in the current-voltage characteristics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ectopic bone formation by marrow stromal osteoblast transplantation using poly(DL-lactic-co-glycolic acid) foams implanted into the rat mesentery

Porous biodegradable poly(DL-lactic-co-glycolic acid) foams were seeded with rat marrow stromal cells and implanted into the rat mesentery to investigate in vivo bone formation at an ectopic site. Cells were seeded at a density of 6.83 x 10(5) cells/cm2 onto polymer foams having pore sizes ranging from either 150 to 300 to 710 microns and cultured for 7 days in vitro prior to implantation. The polymer/cell constructs were harvested after 1, 7, 28, or 49 days in vivo and processed for histology and gel permeation chromatography. Visual observation of hematoxylin and eosin-stained sections and von Kossa-stained sections revealed the formation of mineralized bonelike tissue in the constructs within 7 days postimplantation. Ingrowth of vascular tissue was also found adjacent to the islands of bone, supplying the necessary metabolic requirements to the newly formed tissue. Mineralization and bone tissue formation were investigated by histomorphometry. The average penetration depth of mineralized tissue in the construct ranged from 190 +/- 50 microns for foams with 500-710-microns pores to 370 +/- 160 microns for foams with 150-300-microns pores after 49 days in vivo. The mineralized bone volume per surface area and total bone volume per surface area had maximal values of 0.28 +/- 0.21 mm (500-710-microns pore size, day 28) and 0.038 +/- 0.024 mm (150-300-microns, day 28), respectively. As much as 11% of the foam volume penetrated by bone tissue was filled with mineralized tissue. No significant trends over time were observed for any of the measured values (penetration depth, bone volume/surface area, or percent mineralized bone volume). These results suggest the feasibility of bone formation by osteoblast transplantation in an orthotopic site where not only bone formation from transplanted cells but also ingrowth from adjacent bone may occur.

NASA Discipline Developmental Biology↗

Grain boundary oxidation and an analysis of the effects of pre-oxidation on subsequent fatigue life

The effects of preoxidation on subsequent fatigue life were studied. Surface oxidation and grain boundary oxidation of a nickel-base superalloy (TAZ-8A) were studied at 600 to 1000 C for 10 to 1000 hours in air. Surface oxides were identified and the kinetics of surface oxidation was discussed. Grain boundary oxide penetration and morphology were studied. Pancake type grain boundary oxide penetrates deeper and its size is larger, therefore, it is more detrimental to fatigue life than cone-type grain boundary oxide. Oxide penetration depth, a (sub m), is related to oxidation temperature, T, and exposure time, t, by an empirical relation of the Arrhenius type. Effects of T and t on statistical variation of a (sub m) were analyzed according to the Weibull distribution function. Once the oxide is cracked, it serves as a fatigue crack nucleus. Statistical variation of the remaining fatigue life, after the formation of an oxide crack of a critical length, is related directly to the statistical variation of grain boundary oxide penetration depth.

Oshida, Y.↗

Grain boundary oxidation and an analysis of the effects of oxidation on fatigue crack nucleation life

The effects of preoxidation on subsequent fatigue life were studied. Surface oxidation and grain boundary oxidation of a nickel-base superalloy (TAZ-8A) were studied at 600 to 1000 C for 10 to 1000 hours in air. Surface oxides were identified and the kinetics of surface oxidation was discussed. Grain boundary oxide penetration and morphology were studied. Pancake type grain boundary oxide penetrates deeper and its size is larger, therefore, it is more detrimental to fatigue life than cone-type grain boundary oxide. Oxide penetration depth, a (sub m), is related to oxidation temperature, T, and exposure time, t, by an empirical relation of the Arrhenius type. Effects of T and t on statistical variation of a (sub m) were analyzed according to the Weibull distribution function. Once the oxide is cracked, it serves as a fatigue crack nucleus. Statistical variation of the remaining fatigue life, after the formation of an oxide crack of a critical length, is related directly to the statistical variation of grain boundary oxide penetration depth.

Oshida, Y.↗

Dielectric and magnetic properties of microwave-absorbing FeAl x O y catalysts fabricated via solution combustion synthesis

Iron-based alumina (FeAl x O y ) nanocomposites are microwave-absorbers and catalysts, which makes them promising for emerging microwave-assisted thermocatalytic technologies. Solution combustion synthesis (SCS) has been used to synthesize FeAl x O y powders, and prior work has demonstrated that adjusting SCS parameters significantly changes phase composition and specific surface area of the products. However, it is unclear how synthesis parameters affect their microwave-absorbing properties, which are essential for optimizing microwave-assisted technologies. To address this challenge, in the present work, twelve different FeAl x O y products were synthesized at different combinations of the SCS parameters such as two fuels (citric acid and glycine), two heating modes (hotplate and muffle furnace), and three Fe:Al molar ratios (2:1, 1:1, 1:2). Dielectric and magnetic properties of the products were characterized using a network analyzer and a vibrating sample magnetometer. Based on the measured permittivity and permeability, penetration depth and reflection loss were calculated as a function of frequency and bed thickness. The products were heated by microwaves at 2.45 GHz and then examined with X-ray diffraction (XRD) analysis. For all products, the magnetic saturation was lower than for bulk iron oxides because of the small crystallite size and aluminum substitution. The use of glycine induced high dielectric losses and enabled fast microwave-heating rates compared to citric acid. Higher Fe:Al ratio also led to higher dielectric and magnetic losses. With glycine fuel, SCS in a furnace induced larger penetration depth and lower microwave absorption than SCS on a hotplate. The minimization of reflected power was more sensitive to the thickness of the product bed than to the frequency of the electromagnetic field. Post-heating XRD analysis revealed different phase transformations in the FeAl x O y powders depending on the SCS parameters. As a result, an FeAl x O y material, synthesized via incipient wetness impregnation, lacked magnetic losses and did not heat well as compared to the SCS products.

Combustion synthesis↗

Single-gap isotropic s- wave superconductivity in single crystals AuSn 4

In this article, London, λ L (T), and Campbell, λ C (T), penetration depths were measured in single crystals of a topological superconductor candidate AuSn 4 . At low temperatures, λ L (T) is exponentially attenuated and, if fitted with the power law, λ(T) ~ T n , gives exponents n > 4, indistinguishable from the isotropic single s- wave gap Bardeen-Cooper-Schrieffer (BCS) asymptotic. The superfluid density fits perfectly in the entire temperature range to the BCS theory. The superconducting transition temperature, T c = 2.40 ± 0.05 K, does not change after 2.5 MeV electron irradiation, indicating the validity of the Anderson theorem for isotropic s- wave superconductors. Campbell penetration depth before and after electron irradiation shows no hysteresis between the zero-field cooling (ZFC) and field cooling (FC) protocols, consistent with the parabolic pinning potential. Interestingly, the critical current density estimated from the original Campbell theory decreases after irradiation, implying that a more sophisticated theory involving collective effects is needed to describe vortex pinning in this system. In general, our thermodynamic measurements strongly suggest that the bulk response of the AuSn 4 crystals is fully consistent with the isotropic s- wave weak-coupling BCS superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A probabilistic model of brittle crack formation

Probability of a brittle crack formation in an elastic solid with fluctuating strength is considered. A set Omega of all possible crack trajectories reflecting the fluctuation of the strength field is introduced. The probability P(X) that crack penetration depth exceeds X is expressed as a functional integral over Omega of a conditional probability of the same event taking place along a particular path. Various techniques are considered to evaluate the integral. Under rather nonrestrictive assumptions, the integral is reduced to solving a diffusion-type equation. A new characteristic of fracture process, 'crack diffusion coefficient', is introduced. An illustrative example is then considered where the integration is reduced to solving an ordinary differential equation. The effect of the crack diffusion coefficient and of the magnitude of strength fluctuations on probability density of crack penetration depth is presented. Practical implications of the proposed model are discussed.

Chudnovsky, A.↗

Studies of anisotropy of iron based superconductors

To study the electronic anisotropy in iron based superconductors, the temperature dependent London penetration depth, Δλ(T), have been measured in several compounds, along with the angular dependent upper critical field, H c2 (T). Study was undertaken on single crystals of Ba(Fe 1-x Co x ) 2 As 2 with x=0.108 and x=0.127, in the overdoped range of the doping phase diagram, characterized by notable modulation of the superconducting gap. Heavy ion irradiation with matching field doses of 6 T and 6.5 T respectively, were used to create columnar defects and to study their effect on the temperature Δλ(T). The variation of the low-temperature penetration depth in both pristine and irradiated samples was fitted with a power-law function Δλ(T) = AT n . Irradiation increases the magnitude of the pre-factor A and decreases the exponent n, similar to the effect on the optimally doped samples. This finding supports the universal s ± scenario for the whole doping range.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Elaboration of the α-model derived from the BCS theory of superconductivity

The single-band α-model of superconductivity (Padamsee et al 1973 J. Low Temp. Phys. 12 387) is a popular model that was adapted from the single-band Bardeen–Cooper–Schrieffer (BCS) theory of superconductivity mainly to allow fits to electronic heat capacity versus temperature T data that deviate from the BCS prediction. The model assumes that the normalized superconducting order parameter Δ(T)/Δ(0) and therefore the normalized London penetration depth λL(T)/λL(0) are the same as in BCS theory, calculated using the BCS value αBCS ≈ 1.764 of α ≡ Δ(0)/kBTc, where kB is The single-band α-model of superconductivity (Padamsee et al 1973 J. Low Temp. Phys. 12 387) is a popular model that was adapted from the single-band Bardeen–Cooper–Schrieffer (BCS) theory of superconductivity mainly to allow fits to electronic heat capacity versus temperature T data that deviate from the BCS prediction. The model assumes that the normalized superconducting order parameter Δ(T)/Δ(0) and therefore the normalized London penetration depth λL(T)/λL(0) are the same as in BCS theory, calculated using the BCS value αBCS ≈ 1.764 of α ≡ Δ(0)/kBTc, where kB is Boltzmann's constant and Tc is the superconducting transition temperature. On the other hand, to calculate the electronic free energy, entropy, heat capacity and thermodynamic critical field versus T, the α-model takes α to be an adjustable parameter. Here we write the BCS equations and limiting behaviors for the superconducting state thermodynamic properties explicitly in terms of α, as needed for calculations within the α-model, and present plots of the results versus T and α that are compared with the respective BCS predictions. Mechanisms such as gap anisotropy and strong coupling that can cause deviations of the thermodynamics from the BCS predictions, especially the heat capacity jump at Tc, are considered. Extensions of the α-model that have appeared in the literature, such as the two-band model, are also discussed. Tables of values of Δ(T)/Δ(0), the normalized London parameter Λ(T)/Λ(0) and λL(T)/λL(0) calculated from the BCS theory using α = αBCS are provided, which are the same in the α-model by assumption. Tables of values of the entropy, heat capacity and thermodynamic critical field versus T for seven values of α, including αBCS, are also presented.

36 MATERIALS SCIENCE↗

Investigating the Depth of Penetration of Radionuclides in Concrete - 16292

This paper focuses on some chemical and structural aspects for mature concrete structural substrate that functions as a barrier to radioactive material migration. Exposure to radioactive material may be a consequence of surface contact, such as resulting from exposure by spills or leaks. In properly-prepared waste storage areas, undamaged paint and sealant helps to protect the structural cement. However, damaged surfaces, cracks, and relatively porous slab seams can offer a preferred migration pathway for spilled contaminates, including radionuclides. The cost of remediation of concrete structures is directly related to the amount of concrete that must be removed and subsequently disposed. A carefully implemented investigative plan can be utilized to determine how much concrete must be removed and the approximate level of volumetric radiological contamination can be used to estimate disposal costs. Normal concrete pore solution is saturated with calcium hydroxide and also contains sodium and potassium hydroxide; the pH is typically 13 to 14. Contaminants (such as uranium) that hydrolyze in alkaline media that form precipitant phases and tend to deposit at the near-surface. However, more soluble contaminants, such as Cs-137 (as Cs{sup +}) and Tc-99 (as the pertechnetate anion TcO{sub 4}{sup -}) diffuse more rapidly (and deeply) into the porous substrate. Profiling the migration of the water-soluble radionuclides into a cure (hardened) cement surface is a challenge, since water-cooled saws, borers and similar implements are often used to excise and/or slice the core. Alternately, dry mechanical fracturing for excavation of cement may introduce the possibility of material cross-contamination and uncertainty for the average sampling depth for the sample collection event, potentially yielding non-representative samples, and may preclude determination of crack formation that may have been present in the native (non-fractured) substrate. Structural concrete is comprised of cement and pozzolan paste, relatively impervious aggregate (typically stone and/or sand), and rebar (iron reinforcement). Near-surface aggregate may act as a hydrolytic barrier, causing contaminants leached into the pore water to by-pass the impervious grains, causing deeper-than expected penetration, especially if there are grain boundary cracks also present to facilitate migration. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Vortex-antivortex coexistence in Nb-based superconductor/ferromagnet heterostructures

Low-temperature magnetic force microscopy was used to study the threshold of nucleation of spontaneous vortex-antivortex structures in superconductor/ferromagnet (S/F) hybrid systems. We investigated S/F heterostructures composed of Py as the magnetic material and Nb as the superconductor, with different thicknesses of Py and Nb. The condition for nucleation of spontaneous vortex-antivortex structures depends on fundamental parameters such as the superconducting penetration depth and the coherence length, as well as on the thickness of the superconducting film and the magnetic domain width. Here, we compare our experimental results with those of existing theoretical models and provide an estimate of the threshold of the local out-of-plane component of the magnetization for different Py film thicknesses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laboratory simulation of intact capture of cometary and asteroidal dust particles in ISAS

In order to develop a collector for intact capturing of cometary dust particles in the SOCCER mission and regolith dust particles released from asteroid surfaces by the impact of projectiles launched from a flying-by spacecraft, various kinds of materials as the collector candidates have been exposed to hypervelocity projectiles in our laboratory. Data based on the penetration characteristics of various materials (penetration depth, hole profile, effectiveness for intact capturing) are greatly increased. The materials tested for these simulation experiments include various kinds of low-density media and multisheet stacks; these are foamed plastics (polystyrene 0.01 g/cc), silica aerogels (0.04 g/cc), air (0.001 g/cc), liquid, and multisheet stack consisting of thin Al sheets (thickness 0.002 to 0.1 mm) or polyethylene sheets. Projectiles used are spheres or cylinders of nylon, polycarbonate, basalt, copper, iron, and volatile organics (e.g.,paradichlorobenzene) of size ranging from 30 micrometers to 1 cm launched by a two-stage light gas gun and a rail gun in ISAS at velocity up to about 7 km/s. Some results obtained by using nylon projectiles of velocity less than about 5 km/s are presented; the penetration depth vs. bulk density of the collector material for several kinds of materials and the velocity at which the projectiles begin to fragment vs. material density for foamed polystyrene.

Fujiwara, A.↗

Boron Doped diamond films as electron donors in photovoltaics: An X-ray absorption and hard X-ray photoemission study

Highly boron-doped diamond films are investigated for their potential as transparent electron donors in solar cells. Specifically, the valence band offset between a diamond film (as electron donor) and Cu(In,Ga)Se₂ (CIGS) as light absorber is determined by a combination of soft X-ray absorption spectroscopy and hard X-ray photoelectron spectroscopy, which is more depth-penetrating than standard soft X-ray photoelectron spectroscopy. In addition, a theoretical analysis of the valence band is performed, based on GW quasiparticle band calculations. The valence band offset is found to be small: VBO=VBM{sub CIGS} – VBM{sub diamond}=0.3 eV±0.1 eV at the CIGS/Diamond interface and 0.0 eV±0.1 eV from CIGS to bulk diamond. These results provide a promising starting point for optimizing the band offset by choosing absorber materials with a slightly lower valence band maximum.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗