Search NASA⌕ Search

SEARCH · Search NASA

Results for “POLYAMIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

An Ionic Liquid Reaction and Separation Process for Production of Hydroxymethylfurfural from Sugars

There has been world-wide interest to making plastics out of renewable biomass feedstock for recent years. Hydroxymethylfurfural (HMF) is viewed as an attractive alternate to terephthalic acid (TPA) for production of polyesters (PET) and polyamides. Conversion of sugars into HMF has been studied in numerous publications. In this work, a complete ionic liquid reaction and separation process is presented for nearly stoichiometric conversion of fructose into HMF. Different adsorbent materials are evaluated and silicalite material is demonstrated effective for isolation of 99% pure HMF from actual ionic liquid reaction mixtures and for recovery of the un-converted sugars and reaction intermediate along with the ionic liquid. Membrane-coated silicalite particles are prepared and studied for a practical adsorption process operated at low pressure drops but with separation performances comparable or better than the powder material. Complete conversion of fresh fructose feed into HMF in the recycled ionic liquid is shown under suitable reaction conditions. Stability of HMF product is characterized. A simplified process flow diagram is proposed based on these research results, and the key equipment such as reactor and adsorbent bed is sized for a plant of 200,000 ton/year of fructose processing capacity. The proposed HMF production process is much simpler than the current paraxylene (PX) manufacturing process from petroleum oil, which suggests substantial reduction to the capital cost and energy consumption be possible. At the equivalent value to PX on the molar basis, there can be a large gross margin for HMF production from fructose and/or sugars.

Liu, Wei↗

Nylon–MOF Composites through Postsynthetic Polymerization

Abstract Hybridization of metal–organic frameworks (MOFs) and polymers into composites yields materials that display the exceptional properties of MOFs with the robustness of polymers. However, the realization of MOF–polymer composites requires efficient dispersion and interactions of MOF particles with polymer matrices, which remains a significant challenge. Herein, we report a simple, scalable, bench‐top approach to covalently tethered nylon–MOF polymer composite materials through an interfacial polymerization technique. The copolymerization of a modified UiO‐66‐NH 2 MOF with a growing polyamide fiber (PA‐66) during an interfacial polymerization gave hybrid materials with up to around 29 weight percent MOF. The covalent hybrid material demonstrated nearly an order of magnitude higher catalytic activity for the breakdown of a chemical warfare simulant (dimethyl‐4‐nitrophenyl phosphate, DMNP) compared to MOFs that are non‐covalently, physically entrapped in nylon, thus highlighting the importance of MOF–polymer hybridization.

Kalaj, Mark↗

Nylon–MOF Composites through Postsynthetic Polymerization

Hybridization of metal–organic frameworks (MOFs) and polymers into composites yields materials that display the exceptional properties of MOFs with the robustness of polymers. However, the realization of MOF–polymer composites requires efficient dispersion and interactions of MOF particles with polymer matrices, which remains a significant challenge. Herein, we report a simple, scalable, bench-top approach to covalently tethered nylon–MOF polymer composite materials through an interfacial polymerization technique. The copolymerization of a modified UiO-66-NH2 MOF with a growing polyamide fiber (PA-66) during an interfacial polymerization gave hybrid materials with up to around 29 weight percent MOF. The covalent hybrid material demonstrated nearly an order of magnitude higher catalytic activity for the breakdown of a chemical warfare simulant (dimethyl-4-nitrophenyl phosphate, DMNP) compared to MOFs that are non-covalently, physically entrapped in nylon, thus highlighting the importance of MOF–polymer hybridization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Low-temperature selective laser sintering 3D printing of PEEK-Nylon blends: Impact of thermal post-processing on mechanical properties and thermal stability

Herein, a high-performance polymer (HPP) (polyether ether ketone, PEEK) blended with a commercial low-temperature polymer (polyamide 12, PA-12) was fabricated using a low-temperature selective laser sintering (SLS) 3D printer. Different post-processing heat treatments were implemented after fabrication to tune the thermal and mechanical properties of printed blends. The specific mechanical modulus of the blend was increased up to 79% in comparison to printed PA-12 samples with heat treatment. Additionally, the thermal resistance of the treated blends greatly exceeded the properties observed using PA-12 alone. This research proposes a methodology to fabricate and engineer HPP using desktop SLS printers through a secondary lower melting temperature material and heat treatments.

36 MATERIALS SCIENCE↗

Reaction Optimization for Enzymatic Deconstruction of Industrially Relevant Nylon Composites

Plastics such as polyamides (PAs) possess unique physicochemical properties that make them indispensable in modern society. However, their energy‐intensive production and challenging end‐of‐life management highlight the urgent need for efficient recycling or remanufacturing solutions. Enzymatic depolymerization offers a promising route toward circular recycling, yet remains constrained by limited enzyme characterization, lack of validation under industrially relevant conditions and substrates, and overall performance. Here, we optimized the reaction conditions for three recently discovered nylon‐degrading enzymes. One of them, Nyl12, achieved product titers with PA6 and PA66 that exceed previously reported values, without enzyme engineering or substrate pretreatment. We further demonstrated the scalability of the process and its application to complex PA‐based materials used in microelectronic components. Analysis of substrate features, including surface area and particle size, revealed key parameters governing enzymatic activity and provided a framework for future pretreatment and process optimization efforts. In combination, these efforts provide a new benchmark for enzymatic nylon recycling.

nylon↗

Hydrotreatment of Nylon 66 and Amide Model Compounds Over Sulfided NiMo Catalysts

Molybdenum sulfide-based catalysts, such as nickel–molybdenum on alumina (NiMoS x /Al 2 O 3 ), are widely used in hydrotreating and have potential for catalyzing waste plastic conversion via hydrogenolysis, yet their performance, such as reaction kinetics and network, for amide-rich polymer feeds is poorly defined. Here we combine Nylon 66 with the amide model compound, N,N-dibutylhexanediamide (DBDAD), to quantify hydrodeoxygenation (HDO) and hydrodenitrogenation (HDN) chemistry in a stirred batch reactor (53 bar H 2 , 280–320°C). DBDAD conversion is near-linear with time, indicating strong adsorption of the substrates on the active sites. Time-resolved product identification indicates parallel C─O first-cleavagedeoxygenation (DO) and C─N first-cleavagedenitrogenation (DN) sequences proceeding through amine and diol intermediates, respectively, to C 4 ─C 6 alkanes. Increasing temperature shifts selectivity toward DN, decreasing the initial r(DO)/r(DN) from 1.38 (280°C) to 0.69 (320°C), with an apparent activation energy of 173 kJ mol −1 for DBDAD conversion. At 300°C, nylon 66 converts faster than DBDAD, producing a complex mixture of oxygen- and nitrogen-containing species and an initial rate ratio r(DO)/r(DN) of 1.6. No heteroaromatic nitrogen products are detected by the method used. These results provide reaction pathways and product signatures relevant to hydro-processing catalysts exposed to polyamide-derived streams.

Nylon 66↗

Self‐Standing Carbon Nanofibers@Carbon Felt Electrodes to Boost Electrolyzer Productivity: Application to the Electro‐Manufacturing of trans ‐3‐Hexenedioic Acid and Adipic Acid

The industrial implementation of electrosynthesis for chemical manufacturing remains constrained by the limited surface area of conventional electrodes. Herein, this challenge is addressed by designing a carbon nanofiber@carbon felt (CNF@CF) electrode platform that combines the high conductivity, flexibility, and ease of handling of commercial carbon felts (CF) with the large surface area and tunable surface chemistry of carbon nanofibers (CNFs). CNFs are deliberately grown onto the CF scaffold to form a sword-in-sheath structure, where entangled nanofibers wrap the felt macrofibers to provide excellent mechanical stability and electrical conductivity without binders. CNF@CF is evaluated both as an electrode and as a catalyst support for the electrochemical hydrogenation of cis,cis-muconic acid (ccMA), a biobased platform molecule key to the production of performance polyamides and renewable Nylon 6,6. As a noncatalytic electrode for the partial hydrogenation to trans-3-hexenedioic acid, CNF@CF achieves a threefold increase in both cumulative productivity and Faradaic efficiency (FE) compared to bare CF. A similar boost in catalytic activity and energy efficiency is observed using Pd/CNF@CF for the hydrogenation of ccMA to adipic acid. These results highlight the opportunities of the CNF@CF platform for electro-organic synthesis and sustainable chemical manufacturing.

electrochemical hydrogenation↗

3D printing of anisotropic Sm–Fe–N nylon bonded permanent magnets

Abstract Fabricating a bonded magnet with a near‐net shape in suitable thermoplastic polymer binders is of paramount importance in the development of cost‐effective energy technologies. In this work, anisotropic Sm 2 Fe 17 N 3 (Sm–Fe–N) bonded magnets are additively printed using SmFeN anisotropic magnetic particles in a polymeric binder polyamide‐12 (PA12). The anisotropic SmFeN bonded magnets are fabricated by Big Area Additive Manufacturing followed by post‐printing alignment in a magnetic field. Optimal post‐alignment results in an enhanced remanence of ∼0.68 T in PA12 reflected in a parallel‐oriented (aligned) measured direction. The maximum energy product achieved for the additively printed anisotropic bonded magnet of Sm–Fe–N in PA12 polymer is 78.8 KJ m −3 . Our results show advanced processing flexibility with 3D printing of the development of SmFeN nylon bonded magnets designed for applications with no critical rare earth magnets.

42 ENGINEERING↗

Advancing reliability assessments of photovoltaic modules and materials using combined-accelerated stress testing

Previously undiscovered failure modes in photovoltaic (PV) modules continue to emerge in field installations despite passing protocols for design qualification and quality assurance. Failure to detect these modes prior to widespread use could be attributed to the limitations of present-day standard accelerated stress tests (ASTs), which are primarily designed to identify known degradation or failure modes at the time of development by applying simultaneous or sequential stress factors (usually two at most). Here, we introduce an accelerated testing method known as the combined-accelerated stress test (C-AST), which simultaneously combines multiple stress factors of the natural environment. Simultaneous combination of multiple stress factors allows for improved identification of failure modes with better ability to detect modes not known a priori. A demonstration experiment was conducted that reproduced the field-observed cracking of polyamide- (PA-) and polyvinylidene fluoride (PVDF)–based backsheet films, a failure mode that was not detected by current design qualification and quality assurance testing requirements. In this work, a two-phase testing protocol was implemented. The first cycle (“Tropical”) is a predominantly high-humidity and high-temperature test designed to replicate harsh tropical climates. The second cycle (“Multi-season”) was designed to replicate drier and more temperate conditions found in continental or desert climates. Testing was conducted on 2 × 2-cell crystalline-silicon cell miniature modules constructed with both ultraviolet (UV)–transmitting and UV-blocking encapsulants. Cracking failures were observed within a cumulative 120 days of the Tropical condition for one of the PA-based backsheets and after 84 days of Tropical cycle followed by 42 days of the Multi-season cycle for the PVDF-based backsheet, which are both consistent with failures seen in fielded modules. In addition to backsheet cracking, degradation modes were observed including solder/interconnect fatigue, various light-induced degradation modes, backsheet delamination, discoloration, corrosion, and cell cracking. The ability to simultaneously apply multiple stress factors may allow many of the test sequences within the standardized design qualification procedure to be performed using a single test setup.

14 SOLAR ENERGY↗

Effects of a composite flame retardant system on the flame retardancy and mechanical performance of epoxy resin adhesive

Abstract A flame‐retarded epoxy resin (ER) adhesive with strong flame retardancy and adhesion performance was prepared. The coated ammonium polyphosphate (MFAPP), melamine (MEL), and organic montmorillonite (OMMT) were mixed to prepare a composite flame retardant. It was subsequently blended with a toughened ER thoroughly and then the mixture was cured with polyamide. The resultant ER adhesive thermosets achieved UL‐94 V‐0 rating during vertical burning test, and the limiting oxygen index value was as high as 31.6%. The shear strength of the ER adhesive was 27.9 MPa when 25 wt% MFAPP/MEL/OMMT was introduced. Compared with the pure adhesive, the flame retardant epoxy adhesive maintained outstanding adhesion performance because of the good compatibility between the composite flame retardant additives and the toughened ER adhesive. Cone calorimetry tests indicated that the release of heat and smoke were obviously declined with the incorporation of the composite flame retardant system in comparison to pure ER adhesive thermoset. The investigation of flame retardant mechanism revealed that the composite MFAPP/MEL/OMMT flame retardant system stimulated the generation of highly expanded, integral, and strong char layer and the formed char layer exerted superior insulation effect during combusiton. The present work provided an alternative approach to prepare flame retardant ER adhesive with the similar excellent adhesive performance.

Li, Sheng↗

Peptide nucleic acid Hoogsteen strand linker design for major groove recognition of DNA thymine bases

Sequence-specific targeting of double-stranded DNA and non-coding RNA via triple-helix-forming peptide nucleic acids (PNAs) has attracted considerable attention in therapeutic, diagnostic and nanotechnological fields. An E-base (3-oxo-2,3-dihydropyridazine), attached to the polyamide backbone of a PNA Hoogsteen strand by a side-chain linker molecule, is typically used in the hydrogen bond recognition of the 4-oxo group of thymine and uracil nucleic acid bases in the major groove. We report on the application of quantum chemical computational methods, in conjunction with spatial constraints derived from the experimental structure of a homopyrimidine PNA·DNA-PNA hetero-triplex, to investigate the influence of linker flexibility on binding interactions of the E-base with thymine and uracil bases in geometry-optimised model systems. Hydrogen bond formation between the N2 E-base atom and target pyrimidine base 4-oxo groups in model systems containing a β-alanine linker (J Am Chem Soc 119:11116, 1997) was found to incur significant internal strain energy and the potential disruption of intra-stand aromatic base stacking interactions in an oligomeric context. Additionally, in geometry-optimised model systems containing a 3-trans olefin linker (Bioorg Med Chem Lett 14:1551, 2004) the E-base swung out away from the target pyrimidine bases into the solvent. These findings are in qualitative agreement with calorimetric measurements in hybridisation experiments at T–A and U–A inversion sites. In contrast, calculations on a novel 2-cis olefin linker design indicate that it could permit simultaneous E-base hydrogen bonding with the thymine 4-oxo group, circumvention and solvent screening of the thymine 5-methyl group, and maintenance of triplex intra-stand base stacking interactions.

59 BASIC BIOLOGICAL SCIENCES↗

Coal polymer composites prepared by fused deposition modeling (FDM) 3D printing

Coal is a vital energy resource worldwide, but pollutants and greenhouse gases from its combustion cause environmental problems. To explore the non-combustion approach to use and valorize coal, anthracite and lignite were blended with polyamide 12 (PA 12) through FDM printing in this work and compared in the composites. By adding lignite, Young’s modulus improved with increasing loading to 50 wt% while tensile strength leveled off among the composites, compared to that of PA 12. By contrast, the addition of anthracite decreased the tensile performance at all loadings. Rheology tests and morphology analyses suggested that the interactions between fillers (anthracite and lignite) and PA 12 may cause differences in tensile properties. In addition, the printed lignite composites showed improved thermal conductivity (~ twofold), indicating lignite demonstrates the potential to build functional composites. This work provides a strategy to use lignite in composites by 3D printing for value-added products and reduces the demand for petroleum-based polymers. Overall, our approach diverts lignite from combustion processes and alleviates the negative impact of lignite use on the environment.

36 MATERIALS SCIENCE↗

Thermal Conductivity of Thermal Interface Materials Evaluated By a Transient Plane Source Method

The thermal conductivity of thermal interface materials (TIMs) has been investigated using a transient plane source (TPS) method. In thermoelectric generators designed for vehicle waste heat recovery, high thermal conductivity materials are needed for the cold-side interface between a polyamide flexible circuit and an aluminum plate heat exchanger. The conventional heat flow method described by ASTM D5470 is often used to determine thermal contact resistance of an interface with a thin layer of interface material. The apparent thermal conductivity values provided by materials manufacturers are used to calculate heat transfer through the interface. Yet, estimated parameters based on the thermal conductivity of a TIM often do not agree with the actual heat transfer through the interface. Thermal conductivity of a series of 10 commercial TIMs were evaluated by applying a small quantity to an embedded TPS sensor. The 2-mm radius sensor was able to operate under standard bulk material measurement mode and produced consistent thermal conductivity measurements of the interface materials. The TPS method is demonstrated to be effective in ranking the available interface materials by thermal conductivity and to ensure that the material with consistent performance can be selected for the thermoelectric generator applications.

36 MATERIALS SCIENCE↗

Impact Damage Behavior of Vinyl Ester-, Epoxy-, and Nylon 6-Based Basalt Fiber Composites

Composite laminates reinforced by woven basalt fibers and based on different polymer matrices were prepared and mechanically characterized, in static and dynamic conditions, to compare the results and evaluate the influence of the matrix type. In this regard, a thermoplastic resin, polyamide 6 (PA6), and two thermosetting matrices, vinyl ester and epoxy grades, commonly used for high-performance applications, were considered. Indentation depth measurements carried out by a confocal microscope and ultrasound analyses performed on specimens subjected to falling dart tests at levels of impact energies lower than the perforation one permitted to evaluate the extent of plastic deformations and of subjected delaminations, respectively. These data have provided useful information about the involved damage mechanisms and highlighted interesting perspective of use for the eco-friendly thermoplastic sample.

36 MATERIALS SCIENCE↗

Fiber Orientation Effects in Fused Filament Fabrication of Air-Cooled Heat Exchangers

Fused filament fabrication (FFF) is a type of additive manufacturing based on material extrusion that has long been considered a prototyping technology. However, the right application of material, process, and product can be used for manufacturing of end-use products, such as air-cooled heat exchangers made by adding fillers to the base polymer, enhancing the thermal conductivity. Fiber fillers lead to anisotropic thermal conductivity, which is governed by the process-induced fiber orientation. This article presents an experimental study on the microstructure-property relationship for carbon fiber-filled polyamide used in FFF. Furthermore, the fiber orientation is measured by micro-computed tomography, and the thermal conductivity of manufactured samples is measured. Although the thermal conductivity is raised by more than three times in the fiber orientation direction at a load of only 12 vol.%, the enhancement is low in the other directions, and this anisotropy, along with certain manufacturing restrictions, influences the final part performance.

36 MATERIALS SCIENCE↗

Structure-dependent mechanisms for plastic degradation in the marine environment

The visible and invisible accumulation of waste plastic in our oceans is a consequence of rapidly increasing inputs and very slow degradation rates. In general, this combination of effects results in long residence times. Nevertheless, the abiological degradation rate of a specific synthetic plastic varies widely, depending on its structural characteristics at the molecular, mesoscopic, and macroscopic levels. This chapter summarizes factors that determine these rates of degradation, and describes their principal mechanisms, for several of the major types of waste plastic found in the oceans. Mechanical forces cause cracking and flaking that break macroplastics into microplastics and even smaller fragments with increasing surface-to-volume ratios. Chemical degradation rates increase with surface area, influenced by intrinsic variations in crystallinity and the presence of additives, as well as extrinsic factors such as temperature, pH, and UV light intensity. Since polyolefin-based plastics are less dense than seawater and lack hydrolysable bonds in their polymer backbones, they accumulate close to the surface of the ocean where photo-oxidation is the principal cause of C–C bond cleavage in the polymer backbone. In contrast, polyesters and polyamides are denser than seawater and they sink, experiencing less exposure to solar irradiation. However, they can also degrade by slow hydrolysis of the C–O or C–N bonds intrinsic to the polymer structures.

Maciulis, Nicholas A.↗

A novel additive manufacturing compression overmolding process for hybrid metal polymer composite structures

Metal polymer composites combining low density, high strength composites with highly ductile and tough metals have gained traction over the last few decades as lightweight and high-performance materials for industrial applications. However, the mechanical properties are limited by the interfacial bonding strength between metals and polymers achieved through adhesives, welding, and surface treatment processes. In this paper, a novel manufacturing process combining additive manufacturing and compression molding to obtain hybrid metal polymer composites with enhanced mechanical properties is presented. Additive manufacturing enabled deposition of polymeric material with fibers in a predetermined pattern to form tailored charge or preform for compression molding. Here, a grade 300 maraging steel triangular lattice is first fabricated using AddUp FormUp350 laser powder bed system and compression overmolded with additively manufactured long carbon fiber-reinforced polyamide-6,6 (40% wt. CF/PA66) preform. The fabricated hybrid metal polymer composites showed high stiffness and tensile strength. The stiffness and failure characteristics determined from the uniaxial tensile tests were correlated to a finite element model within 20% deviation. Fractographic analyses was performed using microscopy to investigate failure mechanisms of the hybrid structures.

36 MATERIALS SCIENCE↗