Results for “Particle Volumes” — Page 13

NASA NTRS1990

Observed particle evolution in the polar stratospheric cloud of January 24, 1989

Particle-size distributions measured from the NASA ER-2 with the new Forward Scattering Spectrometer Probe 300 in a type I polar stratospheric cloud (PSC) on January 24, 1989 show a volume mode near 0.8 micron in diameter. The large increase in particle concentration and volume after cloud entry did not occur until the apparent saturation ratio of nitric acid with respect to nitric acid trihydrate reached 10, but at ratios near 1 subtle changes in the size distribution suggest some type I particles were present. Particle concentrations in cloud of 15-17/cu cm were greater than the CN concentrations of 5-7/cu cm just outside of cloud, suggesting nucleation on more than just sulfate particles. Some particles greater than 4 microns in diameter were observed in a region which was saturated with respect to ice.

Dye, J. E.↗

NASA NTRS2014

Investigating the Aerosol Optical and Radiative Characteristics of Heavy Haze Episodes in Beijing During January of 2013

Several heavy atmospheric haze pollution episodes occurred over eastern and northern China during January of 2013. The pollution covered more than 100 sq km and caused serious impacts on environmental quality, human health, and transportation. In this study, we characterize aerosol microphysical, optical, and radiative characteristics using a combination of ground-based Sun/sky radiometer retrievals and a radiative transfer model. Our results show that during about half of the total number of days, daily PM2.5 and PM10 concentrations are larger than 100 microg/cu m, with maxima of 462 and 433 microg/cu m, respectively, during the haze events. Fine-mode (PM2.5) particles dominated the aerosol size during the episodes. The volume size distribution and median radius of fine-mode particles generally increase as aerosol optical depth at 440 nm (AOD440) increases. The median effective radius of fine-mode particles increases from 0.15 microns at low AOD value (AOD440~0.3) to a radius of 0.25-0.30 microns at high AOD value (AOD440> or = 1.0). The daily mean single-scattering albedo (SSA), imaginary part of refractive index (RI), and asymmetry factor display pronounced spectral behaviors. The overall mean SSA440 and SSA675 are 0.892 and 0.905, respectively. The corresponding RI440 and RI675 are 0.016 and 0.011, respectively. This indicates that a significant amount of absorption occurred under the haze event in Beijing during January 2013. Approximately half of the incident solar radiation energy went into heating the atmosphere as a result of strong aerosol loading and absorption. The daily averaged heating rate in the haze particle layer (0-3.2 km) varies from 0.12 to 0.81 K/day in Beijing, which might exert profound impact on the atmospheric thermodynamic and dynamical structures and cloud development, which should be further studied.

bejing↗

NASA NTRS2015

Retrieval of Aerosol Microphysical Properties from AERONET Photo-Polarimetric Measurements. 2: A New Research Algorithm and Case Demonstration

A new research algorithm is presented here as the second part of a two-part study to retrieve aerosol microphysical properties from the multispectral and multiangular photopolarimetric measurements taken by Aerosol Robotic Network's (AERONET's) new-generation Sun photometer. The algorithm uses an advanced UNified and Linearized Vector Radiative Transfer Model and incorporates a statistical optimization approach.While the new algorithmhas heritage from AERONET operational inversion algorithm in constraining a priori and retrieval smoothness, it has two new features. First, the new algorithmretrieves the effective radius, effective variance, and total volume of aerosols associated with a continuous bimodal particle size distribution (PSD) function, while the AERONET operational algorithm retrieves aerosol volume over 22 size bins. Second, our algorithm retrieves complex refractive indices for both fine and coarsemodes,while the AERONET operational algorithm assumes a size-independent aerosol refractive index. Mode-resolved refractive indices can improve the estimate of the single-scattering albedo (SSA) for each aerosol mode and thus facilitate the validation of satellite products and chemistry transport models. We applied the algorithm to a suite of real cases over Beijing_RADI site and found that our retrievals are overall consistent with AERONET operational inversions but can offer mode-resolved refractive index and SSA with acceptable accuracy for the aerosol composed by spherical particles. Along with the retrieval using both radiance and polarization, we also performed radiance-only retrieval to demonstrate the improvements by adding polarization in the inversion. Contrast analysis indicates that with polarization, retrieval error can be reduced by over 50% in PSD parameters, 10-30% in the refractive index, and 10-40% in SSA, which is consistent with theoretical analysis presented in the companion paper of this two-part study.

aerosol retrieval algorithm↗

NASA NTRS1984

Ice depolarization on low-angle 2 GHz satellite downlinks

The impact of ice depolarization on the statistical performance of satellite downlinks were investigated. Propagation data recorded during 1979 and 1980 to see what impact of ice depolarization on link performance were analyzed. The effects on the cross polarization discrimination (XPD) statistics amounted to at most a 2 to 4 dB reduction in the XPD values which rain would have produced for a given percentage of time. Ice depolarization had no effect on the statistics of XPD values below the 0.01% level. Most of the severe ice depolarization events were associated with drops in barometric pressure and the passage of intense cold fronts through our area. Ice contents as the product of three individually undetermined quantities were defined: ice particle density, ice cloud thickness, and the average volume of the ice crystals. It is indicated that populations of ice particle with ice contents on the order of 0.002 m4/m3 are probably responsible for the lower values of measured XPD.

Stutzman, W. L.↗

NASA NTRS2018

Solid State Ultracapacitor

An ink of the formula: 60-80% by weight BaTiO3 particles coated with SiO2; 5-50% by weight high dielectric constant glass; 0.1-5% by weight surfactant; 5-25% by weight solvent; and 5-25% weight organic vehicle. Also a method of manufacturing a capacitor comprising the steps of: heating particles of BaTiO3 for a special heating cycle, under a mixture of 70-96% by volume N2 and 4-30% by volume H2 gas; depositing a film of SiO2 over the particles; mechanically separating the particles; incorporating them into the above described ink formulation; depositing the ink on a substrate; and heating at 850-900 C for less than 5 minutes and allowing the ink and substrate to cool to ambient in N2 atmosphere. Also a dielectric made by: heating particles of BaTiO3 for a special heating cycle, under a mixture of 70-96% by volume N2 and 4-30% by volume H2 gas; depositing a film of SiO2 over the particles; mechanically separating the particles; forming them into a layer; and heating at 850-900 C for less than 5 minutes and allowing the layer to cool to ambient in N2 atmosphere.

Rolin, Terry D.↗

NASA NTRS2005

Discontinuous pore fluid distribution under microgravity--KC-135 flight investigations

Designing a reliable plant growth system for crop production in space requires the understanding of pore fluid distribution in porous media under microgravity. The objective of this experimental investigation, which was conducted aboard NASA KC-135 reduced gravity flight, is to study possible particle separation and the distribution of discontinuous wetting fluid in porous media under microgravity. KC-135 aircraft provided gravity conditions of 1, 1.8, and 10(-2) g. Glass beads of a known size distribution were used as porous media; and Hexadecane, a petroleum compound immiscible with and lighter than water, was used as wetting fluid at residual saturation. Nitrogen freezer was used to solidify the discontinuous Hexadecane ganglia in glass beads to preserve the ganglia size changes during different gravity conditions, so that the blob-size distributions (BSDs) could be measured after flight. It was concluded from this study that microgravity has little effect on the size distribution of pore fluid blobs corresponding to residual saturation of wetting fluids in porous media. The blobs showed no noticeable breakup or coalescence during microgravity. However, based on the increase in bulk volume of samples due to particle separation under microgravity, groups of particles, within which pore fluid blobs were encapsulated, appeared to have rearranged themselves under microgravity.

manned↗

NASA NTRS2007

Development of a Reactor Model for Chemical Conversion of Lunar Regolith

Lunar regolith will be used for a variety of purposes such as oxygen and propellant production and manufacture of various materials. The design and development of chemical conversion reactors for processing lunar regolith will require an understanding of the coupling among the chemical, mass and energy transport processes occurring at the length and time scales of the overall reactor with those occurring at the corresponding scales of the regolith particles. To this end, a coupled transport model is developed using, as an example, the reduction of ilmenite-containing regolith by a continuous flow of hydrogen in a flow-through reactor. The ilmenite conversion occurs on the surface and within the regolith particles. As the ilmenite reduction proceeds, the hydrogen in the reactor is consumed, and this, in turn, affects the conversion rate of the ilmenite in the particles. Several important quantities are identified as a result of the analysis. Reactor scale parameters include the void fraction (i.e., the fraction of the reactor volume not occupied by the regolith particles) and the residence time of hydrogen in the reactor. Particle scale quantities include the time for hydrogen to diffuse into the pores of the regolith particles and the chemical reaction time. The paper investigates the relationships between these quantities and their impact on the regolith conversion. Application of the model to various chemical reactor types, such as fluidized-bed, packed-bed, and rotary-bed configurations, are discussed.

Hedge, uday↗

NASA NTRS2009

Development of a Reactor Model for Chemical Conversion of Lunar Regolith

Lunar regolith will be used for a variety of purposes such as oxygen and propellant production and manufacture of various materials. The design and development of chemical conversion reactors for processing lunar regolith will require an understanding of the coupling among the chemical, mass and energy transport processes occurring at the length and time scales of the overall reactor with those occurring at the corresponding scales of the regolith particles. To this end, a coupled transport model is developed using, as an example, the reduction of ilmenite-containing regolith by a continuous flow of hydrogen in a flow-through reactor. The ilmenite conversion occurs on the surface and within the regolith particles. As the ilmenite reduction proceeds, the hydrogen in the reactor is consumed, and this, in turn, affects the conversion rate of the ilmenite in the particles. Several important quantities are identified as a result of the analysis. Reactor scale parameters include the void fraction (i.e., the fraction of the reactor volume not occupied by the regolith particles) and the residence time of hydrogen in the reactor. Particle scale quantities include the time for hydrogen to diffuse into the pores of the regolith particles and the chemical reaction time. The paper investigates the relationships between these quantities and their impact on the regolith conversion. Application of the model to various chemical reactor types, such as fluidized-bed, packed-bed, and rotary-bed configurations, are discussed.

Hegde, U.↗

NASA NTRS2008

Analysis of Thermal and Reaction Times for Hydrogen Reduction of Lunar Regolith

System analysis of oxygen production by hydrogen reduction of lunar regolith has shown the importance of the relative time scales for regolith heating and chemical reaction to overall performance. These values determine the sizing and power requirements of the system and also impact the number and operational phasing of reaction chambers. In this paper, a Nusselt number correlation analysis is performed to determine the heat transfer rates and regolith heat up times in a fluidized bed reactor heated by a central heating element (e.g., a resistively heated rod, or a solar concentrator heat pipe). A coupled chemical and transport model has also been developed for the chemical reduction of regolith by a continuous flow of hydrogen. The regolith conversion occurs on the surfaces of and within the regolith particles. Several important quantities are identified as a result of the above analyses. Reactor scale parameters include the void fraction (i.e., the fraction of the reactor volume not occupied by the regolith particles) and the residence time of hydrogen in the reactor. Particle scale quantities include the particle Reynolds number, the Archimedes number, and the time needed for hydrogen to diffuse into the pores of the regolith particles. The analysis is used to determine the heat up and reaction times and its application to NASA s oxygen production system modeling tool is noted.

Hegde, U.↗

NASA NTRS2009

Analysis of Thermal and Reaction Times for Hydrogen Reduction of Lunar Regolith

System analysis of oxygen production by hydrogen reduction of lunar regolith has shown the importance of the relative time scales for regolith heating and chemical reaction to overall performance. These values determine the sizing and power requirements of the system and also impact the number and operational phasing of reaction chambers. In this paper, a Nusselt number correlation analysis is performed to determine the heat transfer rates and regolith heat up times in a fluidized bed reactor heated by a central heating element (e.g., a resistively heated rod, or a solar concentrator heat pipe). A coupled chemical and transport model has also been developed for the chemical reduction of regolith by a continuous flow of hydrogen. The regolith conversion occurs on the surfaces of and within the regolith particles. Several important quantities are identified as a result of the above analyses. Reactor scale parameters include the void fraction (i.e., the fraction of the reactor volume not occupied by the regolith particles) and the residence time of hydrogen in the reactor. Particle scale quantities include the particle Reynolds number, the Archimedes number, and the time needed for hydrogen to diffuse into the pores of the regolith particles. The analysis is used to determine the heat up and reaction times and its application to NASA s oxygen production system modeling tool is noted.

Hegde, U.↗

NASA NTRS1979

A high resolution holographic particle sizing system

This paper will review briefly the requirements of holography with respect to particle sizing techniques. A holographic construction system and the appropriate reconstruction system will be discussed regarding their characteristics and performance (i.e. system resolution, magnification, system aberration and correction of aberrations, and maximum total test volume). The capabilities of a commercial particle sizing system used to obtain particle sizes and distribution information from reconstructed holograms will be described and characterized. It will be shown that by using the methods described, high resolution throughout large test volumes can be achieved.

Witherow, W. K.↗

NASA NTRS1990

The Mechanisms of Dispersion Strengthening and Fracture in Al-based XD (TM) Alloys

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength, and the fracture toughness of metal matrix composites of both pure aluminum and Al(4 percent)Cu(1.5 percent)Mg with 0 to 15 vol percent TiB2 were examined. Higher TiB2 volume fractions increased the tensile yield strength both at room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. The fracture toughness of the Al(4 percent)Cu(1.5 percent)Mg alloys decreased rapidly with TiB2 additions of 0 to 5 vol percent and more slowly with TiB2 additions of 5 to 15 vol percent. Fracture toughness appears to be independent of TiB2 particle size. The isothermal-aging response of the precipitation strengthened Al(4 percent)Cu(1.5 percent)Mg alloys was not altered by the presence of TiB2.

Aiken, R. M., Jr.↗

NASA NTRS1990

The mechanisms of dispersion strengthening and fracture in Al-based XD(tm) alloys, part 1

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength; the fracture toughness; and the fatigue crack growth rate of metal matrix composites of Al-4(pct)Cu-1.5(pct)Mg with TiB2 were examined. The influence of reinforcement volume fraction was also examined for pure aluminum with TiB2. Higher TiB2 volume fractions increased the tensile yield strength at both room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. Interparticle spacing appears to be the factor that controls the strength of these alloys, with the exact nature of the dependence relying on the nature of dislocation slip in the matrix (planar vs. diffuse). The isothermal aging response of the precipitation strengthened Al-4(pct)Cu-1.5(pct)Mg alloys was not accelerated by the presence of TiB2. Cold work prior to artificial aging created additional geometrically necessary dislocations which serve as heterogeneous nucleation sites leading to accelerated aging, a finer precipitate size, and an increase in the strength of the alloy.

Aikin, R. M., Jr.↗

NASA NTRS1981

Energetic storm particle events in the outer heliosphere

The evolution of energetic particle events with increasing heliocentric distance is studied through events of Pioneers 10 and 11. Beyond 12 AU the events become the dominant type of solar particle event at 1 AU, and the combined effects of adiabatic cooling and volume expansion rule out the possibility that the particles represent the confinement of the original particle population behind the shock. It is not established whether the particles originate from the solar wind by injection via post-shock enhancements or are energetic solar particles further energized by the shock, although their very long lifetime favors the solar wind origin.

Mcdonald, F.↗

NASA NTRS1998

A New Optical Aerosol Spectrometer

An optical particle spectrometer capable of measuring aerosol particle size distributions from 0.02 to 100 micrometers has been developed. This instrument combines several optical methods in one, in-situ configuration; it can provide continuous data collection to encompass the wide dynamic size ranges and concentrations found in studies of modeled planetary atmospheres as well as terrestrial air quality research. Currently, the system is incorporated into an eight liter capacity spherical pressure vessel that is appropriate both for flowthrough and for in-situ particle generation. The optical sizing methods include polarization ratio, The scattering, and forward scattering detectors, with illumination from a fiber-coupled, Argon-ion laser. As particle sizes increase above 0.1 micrometer, a customized electronics and software system automatically shifts from polarization to diffraction-based measurements as the angular scattering detectors attain acceptable signal-to-noise ratios. The number concentration detection limits are estimated to be in the part-per-trillion (ppT by volume) range, or roughly 1000 submicron particles per cubic centimeter. Results from static experiments using HFC134A (approved light scattering gas standard), flow-through experiments using sodium chloride (NaCl) and carbon particles, and dynamic 'Tholin' (photochemical produced particles from ultraviolet (UV)-irradiated acetylene and nitrogen) experiments have been obtained. The optical spectrometer data obtained with particles have compared well with particle sizes determined by electron microscopy. The 'Tholin' tests provided real-time size and concentration data as the particles grew from about 30 nanometers to about 0.8 micrometers, with concentrations ranging from ppT to ppB, by volume. Tests are still underway, to better define sizing accuracy and concentration limits, these results will be reported.

Fonda, Mark↗

NASA NTRS1974

Implications of the Pioneer 10 measurements of the Jovian magnetic field for theories of Io-modulated decametric radiation

The configuration of the magnetic field of Jupiter imposes constraints upon theoretical models of decametric emission triggered by Io, with respect to such features as the frequency of the emission, the density of the inner plasmasphere, and the beaming pattern. Owing to the northern offset of the field model reported by Smith et al. (1974), the upper ranges of observed decametric frequencies can be equated to the electron gyrofrequency only in the northern hemisphere, in regions outside the trapping volume of radiation-belt particles. Emission mechanisms in which the frequency is at or very near the electron gyrofrequency must be stimulated by Io either through acceleration and precipitation of particles or through generation of MHD waves. Mechanisms invoking trapped particles are consistent with wave amplification in the southern hemisphere at the upper hybrid frequency, imposing a lower bound on the density of thermal plasma near the planet.

Smith, R. A.↗

NASA NTRS1975

Atmospheric particulate measurements in Norfolk, Virginia

Characterization of atmospheric particulates was conducted at a site near the center of Norfolk, Virginia. Air quality was measured in terms of atmospheric mass loading, particle size distribution, and particulate elemental composition for a period of 2 weeks. The objectives of this study were (1) to establish a mean level of air quality and deviations about this mean, (2) to ascertain diurnal changes or special events in air quality, and (3) to evaluate instrumentation and sampling schedules. Simultaneous measurements were made with the following instruments: a quartz crystal microbalance particulate monitor, a light-scattering multirange particle counter, a high-volume air sampler, and polycarbonate membrane filters. To assess the impact of meteorological conditions on air quality variations, continuous data on temperature, relative humidity, wind speed, and wind direction were recorded. Particulate elemental composition was obtained from neutron activation and scanning electron microscopy analyses of polycarbonate membrane filter samples. The measured average mass loading agrees reasonably well with the mass loadings determined by the Virginia State Air Pollution Control Board. There are consistent diurnal increases in atmospheric mass loading in the early morning and a sample time resolution of 1/2 hour seems necessary to detect most of the significant events.

Storey, R. W., Jr.↗

NASA NTRS1979

Design, development, and test of a laser velocimeter for a small 8:1 pressure ratio centrifugal compressor

The instrument was designed as a diagnostic tool for the basic fluid dynamics of the inducer, impeller, and diffuser regions of this type compressor. The LV instrumentation was optimized to measure instantaneous velocities up to approximately 500 m/s, measured in absolute coordinates, within the rotating compressor impeller and in the two dimensional radial plane of the diffuser. Some measurements were made within the diffuser and the impeller inlet flows; however, attempts to make detailed measurements of the velocity field were not successful. Difficulties in maintaining high seed particle rates within the probe volume and the improper operation of the blade gating optics may explain the lack of success. Recommendations are made to further pursue these problems. At 100% speed the stage attained a total static pressure ratio of 7.5:1 at 75% total-static efficiency. Flow range from choke-to-surge was 6.8% of choking mass flow rate. Performance was lower than the design intent of 8:1 pressure ratio at 77% efficiency and 12% flow range. Detailed measurements of the stage components are presented which show the reasons for the stage performance deficiencies.

Dolan, F. X.↗